Search Documents

By Thatcher R

In areas where undeveloped land represents a scarce resource, an upgraded post mining land use can result in economic benefits to both the mining company and to the community. A study undertaken at Allied Queensland Coalfields Ltd's Aberdare Colliery located between Brisbane and Ipswich during 1986/1987, assessed the costs and benefits of developing the site following mining for grazing, forestry and residential uses. The proposed final land use plan comprised a combination of these uses which can be upgraded to higher valued uses once subsidence monitoring of backfilled opencut areas and dumps indicates that total settlement has reached acceptable levels. The study involved the documentation of existing site environmental parameters and the delineation of site opportunities and constraints. The unpredictable nature of settlement over backfilled opencuts and overburden dumps represents the major constraint to urban development on mined areas.

Jan 1, 1987

By A Domanti, C Jewkes

This paper describes the design and constructability issues investigated in the selection of a trenchless solution in comparison to trenched construction options as part of a scoping study for the augmentation of the existing Bulimba Creek Trunk Sewer in Brisbane. Initial work involved the planning of alignment options vis-a-vis ground geology, geotechnical conditions, location and depth of shafts considering potential construction technology, flotation and stability of the tunnel, availability of construction sites and the influence of construction works on neighbourhood properties and the immediate environment. Two design pipe sizes, DN1200 and DN1500, were considered, and factors including jacking forces, specification of product pipes, pipe joints, pipe jacking methods and the associated impacts of ground settlement were carried out. Of particular interest was research on suitable lubricating fluids with the potential to minimise jacking forces and maximise the length of pipeline between launch and reception shafts.

Jan 1, 2008

Railway cuttings require the highest care in design and construction, as the pro- bability of failure concept does not allow any risks to be taken with hundreds of lives being dependent on continued stability. The usual geological influences on stability such as bedding dip and faulting are often discus- sed, but other major problems may come from the presence of sheet joints, cross joints differential weathering and seasonal or daily changes of ground water level. The design of rail cuttings has taken little note of the problems imposed by cons- truction methods, and low cost quarrying methods may seriously weaken a designed shape. The presence of berms and drainage ditches is often difficult to achieve as blasting imposes cumulative stresses and jointing on rocks. Contractors face difficulties in bidding extensive rock cuttings as variations in rock properties are often concealed and overshoot- ing the toe of a batter can easily occur. Modern blasting methods offer some solutions, but the best guide to safe successful cuttings is extensive investigation and the continued involvement of engineering geology at the stages of feasibility, design, construction and maintenance. Two case histories show the influence of folding, faulting and construction methods in the case of slope failure and slope stability.

Jan 1, 1979

By Tack K

During its 28-year life the MHD ISP smelter has gone through two phases, each of about a dozen years. The first phase was a learning one; in the second phase the lessons were applied and throughput and production rose strongly. Early experience revealed the robustness and the flexibility of the Imperial Smelting Process. The experience was demonstrated by strong increases in the throughput of mixed lead-zinc concentrates and of secondary (oxide) zinc materials. Purchased material quantities rose from 175 000 tonnes/year to 200 000. The required capacity increase of the IS furnace to smelt the higher throughput was achieved by relatively minor modifications; for instance a change to the internal furnace profile gained an extra two square metres in cross sectional area. The furnace hearth area has remained practically unchanged over its entire history. The paper concludes that there is still more potential to be drawn from the process and MHD intends to sustain raw material input at a new level of 240 000 tonnes/year. However, this rate will have to be achieved under the imposition of more stringent environmental and product quality standards than ever before.

Jan 1, 1993

By O J. Restrepo Baena, S Nowosad, R Webber-Youngman, N Mojtabai, P Foster, A Binder, S Hazuria, erson, S Raval, L Liu

As the mining industry faces times of change, new challenges arise to ensure raw material supply for the younger and future generations. Different scenarios are currently shaping the way we mine and teach mining engineering. Led by an increasing demand for raw materials, net zero requirements for improving long-term operation performance, technological advancements such as automation and digitalisation, safety improvements, environmental considerations and a need for social acceptance, mining is pursuing to change and adapt to these requirements at a faster pace. Such changing times raise new concerns, one of the most relevant is the lower number of students interested or enrolling in mining engineering and related fields leaving mining engineering as one of the less preferred career options between the younger generations. Nonetheless, it is essential to continue addressing and supplying the skill sets that is suited to contemporary and future of the mining industry. To this end, globally, academia is currently undergoing several initiatives such as curricula updates and adaptation, up skilling, improving teaching practices and techniques, including e-learning techniques, enhancing industry-academia and inter-university collaboration, and much more

Sep 1, 2024

By D A. Deglon

Solids suspension is important in the design and operation of mechanical flotation cells, and is a necessary precondition to particle collection. Most of the fundamental hydrodynamic research that incorporates some aspect of solids suspension was done by Arbiter, Harris, and co-workers, or Schubert and co-workers. However, a need for research into solids suspension in mechanical flotation cells exists, since very little has been done since the late 1980s; a time that also coincides with the advent of round mechanical flotation cells and the subsequent dramatic increases in maximum flotation cell sizes. In this work, concentration profiles and critical impeller speeds, Njs, were measured in a 0.124 m3, round cell fitted with a 0.150 m, Bateman impeller mechanism. Two solids size fractions (75 - 106 and 150 - 250 ¦m) were tested, in ungassed and gassed conditions (JG = 0, 1 cm/s) and at various impeller speeds (300 - 900 rpm). The effectiveness of solids suspension was quantified in three ways in terms of extent of off-bottom solids suspension, suspension height (extent of solids distribution), and variation within the solids distribution, which together present a complete quantitative picture of solids suspension and distribution within the cell. Consistent trends were found when these effectiveness criteria were considered against relative impeller speed, in terms of percentage of critical impeller speed, N/Njs. Off-bottom solids suspension is complete at or above 100 per cent of Njs, with significant sedimentation occurring as the impeller speed drops below 60 per cent of Njs. Suspension heights consistently reached a level equivalent to 90 per cent of the tank diameter at the critical impeller speed, and dropped off significantly as N/Njs dropped below 60 per cent. The variation in the solids concentrations within the sampled profiles showed consistent trends in two-phase but not under three-phase conditions. The paper concludes that the critical impeller speed, Njs, commonly used in the design and operation of standard stirred tanks, is a very useful solids suspension benchmark for describing all aspects of solids suspension in mechanical flotation cells and should be correlated to system conditions.

Jan 1, 2005

Modern minerals projects face serious challenges in earning and maintaining acceptance by their key stakeholders. Factors which underpin effective response to managing these challenges include consideration of public affairs issues from the earliest planning stages, building robust alliances with a range of influential partners, developing a level of transparency in all operations and decision-making and integrating activities towards resolving key strategic issues. Effective community relations is vital and there are a number of elements common to the best approaches. These include senior management support and involvement, appropriate involvement in project decisions and activities by community members and company responsiveness to community expectations. The project's operations manager and executive team must fully commit to developing the capability and processes to meet these challenges. They require a whole of project response and it is not an option to manage them peripherally.

Jan 1, 1997

By F Jullian, L Jofre

Many maintenance managers find it difficult to justify investments in maintenance improvement initiatives. In part, this is due to a tendency by mine managers to regard maintenance purely as a cost centre, and not as a process able to influence productive capacity and profit. It is also hindered by a lack of alignment between commonly used maintenance performance measures and key business drivers, and the lack of formal business training amongst maintenance professionals. With this in mind, a model to assist maintenance managers in evaluating the benefits of maintenance improvement projects was recently formulated. The model considers four cost saving dimensions. These are: 1. reduction in the cost of unplanned repairs and maintenance,2. increased or accelerated production and/or sales,3. spares inventory reduction, and4. reduction in over-investment in physical assets and operating costs. This paper discusses the application of this model and a number of numerical examples are given to justify investments in maintenance improvement projects having varying objectives.

Jan 1, 2006

By Baafi EY

Deposits of gold, silver and other precious metals often display a high variability of grade values, usually a very low average metal content and are frequently not easy to sample reliably. The characteristics, together with the volatility of precious metal prices, make evaluations of precious metal deposits extremely difficult to make. Geostatistical estimation techniques can be used to make grade estimates of precious metals and to assess the reliability of these estimates. Two case studies are presented.

Jan 1, 1987

By Wright G. N

Curragh Queensland Mining Limited, a co-venture of Australian and overseas interests, operates an open cut coal mine 13 km north of the township of Blackwater in Central Queensland, refer attached location map.

Jan 1, 1992

By Quilliam B, Richmond G

Aberfoyle Ltd. has utilised a variety of flotation technologies in the Hellyer concentrator in North-Western Tasmania. Hellyer ore, with its slow flotation rates and low rate differentials between values and gangue, requires the use of long residence times and low air consumption rates in the flotation circuit. The operation of the flotation circuit, with a nominal residence time of 7 hours, has necessitated the development of a control system to provide continuity through operator shift changes. Cell selections at Hellyer varied from the 54 m3 hybrid Dorf Oliver / Maxwell (DO/MX) cells, to smaller 32 m3 Maxwell cells, conventional Don-Oliver 300 (8.5 m3) and 600 (17 m3) trough cells, and a column cell. The advantages of the large cells included low specific power consumptions and a low capital cost. However, problems with mixing and the maintenance of consistent froth depth have been identified in the hybrid DO/MX cells. Short circuiting in the trough cells was apparent, causing a considerable reduction in metallurgical performance. The column cell performs to expectation, although the application is not ideal.

Jan 1, 1991

Mathematical modelling of continuous rotary vacuum filtration has been limited by the wide range of variables and the absence of connecting equations linking the variables. The filter type and size, mechanical design and predicted performance are generally determined by laboratory leaf tests on representative samples of slurry, or plant samples from an operating filter. A model has been developed which includes the major process variables such as slurry feed rate and concentration, cake thickness, wash water and air flow rates, to predict the filter production throughput, cake moisture and residual solubles. Where possible the model incorporates well established equations relating form filtration, washing and drying rates of the filter cake. Where an equation has not been formulated, standard curve fitting programs have been used to establish an algorithm. The theoretical equations and the derived algorithms are defined in the text. A major feature of the model is that operators, metallurgists, process, mechanical and instrumentation engineers become more aware of the interaction of process variables, the principles of the equipment design and its limitations when operating at peak performance. The model has specific application in the alumina industry where a high moisture content of the filter cake can increase chemical losses and energy costs, and in the coal industry where overseas companies are insisting on lower export coal moistures.

Jan 1, 1989

By Kikuta K

ISP (Imperial Smelting Process) produces zinc and lead simultaneously from zinc and lead sulphide concentrates and recovers copper and precious metals into a lead bullion. The strength of sinter is important to keep permeability in the shaft of the Imperial Smleting Furnace. The residual sulphur content of the sinter is also important as it causes metal losses into slag. The paper describes an investigation into the sintering operations to improve sulphur elimination and sinter strength. The micro structure of the sinter and the effect of the blast rate, sintering temperature etc have been studied.

Jan 1, 1993

By K Orth

The volcanic successions that host massive sulphide deposits are diverse in composition, facies types and facies relationships. They also show a variety of spatial and temporal relationships to mineralisation. In many examples, such as the Koongie Park Formation in Western Australia, the host succession includes more or less conformable syn-volcanic sills with peperitic contacts. Such sills can be an important source of heat for fluid circulation, influencing patterns of hydrothermal alteration and the location of co-eval and later mineralisation. The impact of syn-volcanic sills on the host succession depends in part on the initial porosity and permeability of the enclosing facies. The special properties of glassy pumice û being highly porous, permeable, and reactive û allow pumice-rich facies to preferentially focus hydrothermal fluid flow. However, the same properties promote early alteration and porosity reduction. Hence, the diagenetic and compaction history of pumiceous facies strongly influences their potential to host massive sulphide mineralisation. In contrast to pumice, dense glass has relatively low porosity, at least initially, and does not compact. Non-vesicular glass is a major component of submarine lavas, syn-volcanic intrusions and some volcaniclastic facies. However, especially in submarine settings, dense glass is commonly intensely perlitically fractured soon after eruption. The fractures greatly increase the porosity and permeability, locally accelerating diagenetic and hydrothermal alteration. In addition to false pyroclastic textures, altered perlite may exhibit false porphyritic textures. Silica- or feldspar-altered perlite kernels surrounded by intensely altered phyllosilicate domains can resemble phenocrysts in a fine grained groundmass.

Jan 1, 1999

Self Advancing or "Poweredtt supports are a successful means of supporting roof and designs have reached the stage where adequate support capa- bility is available for all conditions. Some designs have resulted in equipment being too difficult to transport underground and too complex to maintain. Current trends are reducing those problems and simplicity in hydraulic systems is now the keynote of both supplier and user. There is a good possibility that the "Shield-Chock" support will be the universal design of the future. So-called t'shortwall supports" have been developed to the point where they can be applied with a high degree of confidence to conditions of great variety. Develop- ments by manufacturers and practices of users related to maintenance should result in consistent achievement of designed performance.

Jan 1, 1974

By Hedley TP

Success for underground coal mine operators in the 1990's and beyond will be dependent upon better understanding of the dynamics of their operating environment, and extension of emerging technologies to reach new levels of output and productivity. The Collieries Division of B.H.P. Steel International Group clearly identifies with the concept of business/product life cycles - and the need to adopt strategies that can drive the business successfully into the future. Three main thrusts within BHP Collieries Division relate to: 1) Detailed assessment of current mines to determine: a) The real output potential of the current facilities. b) What factors now inhibit the full potential from being realised. c) Opportunities that exist to enhance overall mine performance. 2) Based upon the findings of these studies, putting into place cost effective strategies and systems for the ongoing "tuning" of the mine. 3) of new/improved technology primarily in areas of: a) Coal cutting and underground coal clearance. b) Controlling the overall mine gas Regime.

Jan 1, 1987

The Savage River Mines concentrator and pipeline has operated for seven years. During this time some problems of general interest have been overcome, particularly in the area of autogenous grinding in large mills and in pump- ing solids over long distances. The plant flow sheet and equipment at Savage River and the control techniques are. described. Ore type has varied widely over the per- iod of plant operation. Techniques developed to minimise the effect of variations on through- put are discussed'. The main technique is the controlled rejection or addition of grinding Media.

Jan 1, 1975

To grow a mining company today is seen to be challenged by the reduced interest in resources companies by the financial markets, the complexity of native title and a somewhat depressed commodity cycle. However, the opportunity to grow production and sales in a mining company are as numerous as they have ever been. It is the challenge of growing significant shareholder value that is difficult. The distinction between growth in æcompany sizeÆ and growth in æshareholder valueÆ is an important distinction upon which some resource companies are now firmly focussed. The equity market/commodity market cycle can provide windows of opportunity to consolidate and expand a company for the benefit of shareholders. These benefits may not be reflected until more buoyant equity markets return but, as the cycle turns, as it surely will, those with the foresight to position themselves may be richly rewarded.

Jan 1, 2000

Comalco's Bell Bay smelter produces some 94 000 t.p.a. of primary aluminium in the form of foundry alloys, extrusion billet and rolling blocks. The extrusion billet and rolling block are produced by a process, in which molten aluminium is poured into an open ended water cooled mould of the required shape. The bottom of the mould is initially closed off by a dummy or starting block. Primary cooling takes place at the mould wall and secondary cooling is achieved by direct water sprays onto the out side shell of the product. Careful preparation of the molten alumin- ium is essential if stringent alloy specific- ation limits are to be met. Optimum casting temperature must be maintained within a narrow range and metal cleanliness is important to ensure a consistent product. Increased demands of recent years for larger product and higher standards of surface quality and dimensional control have been instrumental in forcing improvements in furn- aces, casting machines and in mould and dummy Doq,

Jan 1, 1977

By E Mielczarski

Determination of the adsorbed layer composition and structure at molecular and atomic levels and understanding adsorption mechanisms and dynamics are vitally important for the preparation of surface layers with specific functions. Direct information, at a molecular level, about mineral surface composition, its structure and surface distribution is crucial to perform an efficient separation process for mineral beneficiation. This information is equally important for modifying surface properties of industrial minerals for specific applications such as: fillers, composites, weathering resistance, etc. An understanding of the mechanisms and kinetics of the interaction of first adsorbed organic molecules with mineral surfaces is a fundamental requirement for the prediction and control of the macroscopic surface properties governing the efficiency of separation technologies or new material formulations. The developed infrared external reflection technique has a unique ability to study interface phenomena, at a molecular level, on heterogeneous substrates. The variety, precision and reliability of information about the interface phenomena delivered by this technique is superior to any other single technique. The experiments are fast and non-destructive. High sensitivity (starting from 20 per cent of the monolayer) in situ collected information in a multiphase system, even in the region of strong absorption of the substrate, makes this technique a very valuable experimental tool. The complexity of the recorded reflection spectra, their sensitivity to variations of the optical properties of all bulk and surface components and their spatial distribution in the system under investigation, are in fact the major strengths of this technique. A few examples of the application of this multi-diagnostic technique, for monitoring surface modifications of semi-soluble minerals for selective flotation, will be discussed in detail in this paper.

Jan 1, 2005