Search Documents

The Iron Prince orebody occurs within the Lower Middleback Jaspilite Horizon of the Middleback Group and consists of hematite within host rocks of jaspilites and schists. The ore was probably the product of leaching of silica from jaspilites and replacement by iron, concentrations occurring in suitable structural traps. The narrowness and the presence of extensive dolerite amphibolite dykes within the orebody make it essential to operate a grade control programme in advance of the faces. Information from drilling is drawn up on bench plans, step plans and impurity overlays, and these serve both in day to day production planning and in long term planning. Mining is done selectively by open-pit methods and blending conducted by keeping at least three faces of different grades of ore open at any one time. No stock piles of ore are kept for blending, but contact ore, contaminated ore and enriched material are dumped for later beneficiation.

Jan 1, 1971

The BLEG (Bulk Leach Extractable Gold) technique is a semiquantitative measure of cyanide extractable gold contained in a sample. A 5kg sample is leached in cyanide solution for 24 hours and gold is precipitated out of the pregnant solution using zinc and assayed by AAS. The detection limit is reported as ppb (parts per billion). Telfer is located 1300km north north-east from Perth in the Great Sandy Desert. The climate is one of hot summers with irregular rainfall and mild winters. A large portion of the area is covered by aeolian sand and seif dunes with poorly developed drainage, rare outcrop; topographic relief is a maximum of 96m. Poor outcrop and poorly developed drainage render conventional stream sediment sampling and soil geochemistry inadequate. Therefore a technique providing a minimum number of samples with maximum accuracy and sensitivity was needed. Consequently BLEG orientation surveys were conducted over the Telfer Mine area in 1983, 1984 and 1985.

Jan 1, 1988

By Hare S. M, Griffin P. T, O&apos

Chalcopyrite ore and converter slag treatment to produce copper concentrates is undertaken at the Copper Concentrator of Mount Isa Mines Limited. This concentrator was commissioned in May 1973, replacing the original No 1 Lead-Zinc Concentrator, for the processing of all chalcopyrite ore coming from Mount Isa Mine.Treatment of chalcopyrite ore at rates of up to 125 000 l/week is described here; the treatment of converter slag is described later.

Jan 1, 1993

By Peck J. P, Kennedy D

Drill performance monitoring studies were recently completed at the Fording River mine, British Columbia. Microprocessor-based instrumen- tation and data analysis techniques were developed with the objective to improve short and long term mine planning. Data analysis permitted the identification of thicknesses and interfaces between soft/hard zones at depth based upon the recorded responses of the drill. Data clearly con- trast the soft coal seams and harder waste rock units based on variations in recorded drill rotary speed and torque, hydraulic downpressure, bail- ing air pressure and instantaneous rate of penetration. These parameters were monitored and recorded at 10 cm sampling intervals. Processed drill data was correlated with gamma logs, an existing means for locating coal seams and distinguishing between waste units. Current development of a pattern recognition module aims towards automated interpretation of drill data, identifying micro-and macro-geological and geomechanical rock mass characteristics. Delay between acquiring, processing and interpret- ing the drill data for practical use by mine personnel should be minimized. Integration of this technology with the mine's current main-frame based Mine Engineering Application System software will enable more accurate and timely annlication of the nrocessed drill data.

Jan 1, 1989

Tectonic subsidence plots have been calculated for well, extrapolated-well and significant off-well (seismically-based) locations in the Vulcan Sub-basin and adjacent highs (western Timor Sea). The subsidence curves have been normalized to a common datum, the distinctive "near top Permian" marker, and corrected for sediment compaction, palaeobathymetry, eustatic sea-level change and loading effects.Four principal phases of post-Permian basin development are recognised and quantitatively described by integrating the results of the sub-sidence analysis into the regional (e.g. recent Ocean Drilling Program-derived) framework of the tectonic evolution of the North West Shelf. They are1. the Triassic-mid Jurassic Westralian Superbasin intracratonic phase,2. the late Jurassic-early Cretaceous North West Shelf rift phase,3. the mid Cretaceous-Palaeogene North West Shelf subsidence phase, and4. the Neogene-present Timor collision phase. Rapid Triassic tectonic subsidence occurred in an intracratonic setting, possibly subsequent to aborted late Palaeozoic rifting. Intracratonic sub-sidence mechanisms such as deep crustal metamorphism and/or intrustion and regional tectonic compression are invoked in addition to any post-rift thermal subsidence which may have occurred.

Jan 1, 1990

By Raymond G. F

Geostatistics - a tool used by geologists and mine planning engineers to estimate grades and rapidly evaluate alternative mining strategies has reached an advanced stage of development for the silver-lead-zinc orebodies at Isa and Hilton Mines. Geostatistics has been used for over a decade in the massive copper orebodies but the stratiform lead-zinc orebodies are much more complex and provided a completely different set of challenges. Recent increases in computer processing speed and power provided by the Integrated Mine Planning System (IMPS) has aided the development of the geostatistics package. Also the formation of a project team and the subsequent in-house development which has drawn together the expertise of geologists, engineers and system analysts has contributed significantly to the success of the project.The most important feature of any approach to modelling the lead-zinc orebodies is that the kriging search must consider estimate and sample points according to their positions relative to bedding surfaces. By transforming co-ordinates as perpendicular offsets from a plane representing the local strike and dip, it is possible to elongate the ellipsoidal influence to parallel bedding. By interactively modelling surfaces using CAD facilities and then specifying these surfaces as 'hard' or 'soft' boundaries, the geologist has complete control over the kriging process.

Jan 1, 1993

By Laird CH

Large quantities of brown coal are excava ted from open cut mines in the Latrobe Valley to fire the base load thermal power stations of the Victorian Electricity System. Most of the coal is removed using bucketwheel excavators which have been modified or specially designed for the conditions encountered. The actual digging efficiency of the bucketwheel excavator is strongly influenced by such factors as wheel speed, slewing speed and tooth design and arrangement. The coal deposit, although not difficult to work, is not uniform and the operation of the machine is influenced by the stability re- quirements of the excavation face.

Jan 1, 1978

Alcoa of Australia's Western Australian bauxite mining operations in the Darling Ranges, southeast of Perth, present major challenges in the control of air blast. The close proximity of rural communities and the face profile make the traditional methods of air blast control difficult.An extensive blast noise monitoring programme has been established. The development of a computerised blast noise prediction model and the establishment of a radiosonde weather balloon facility have reduced blast induced complaints by a factor of ten.The meteorological factors affecting blast noise transmission are discussed and examples are given of adverse weather conditions for the southwest region of Western Australia.

Jan 1, 1983

The high maintenance of load-haul-dumps (LHDs) and front end loaders in hard rock affects mine planning with reduced availability and productivity. Intensive study of maintenance costs and availability of machines related to machine age and life provide the basis for planning from available operational alternatives.Derived programmes and experiences have led to the beginnings of unmanned operation and automation through reduction of manual diesel units and spreading electrification and use of radio. But electrification has obvious layout limitations. This approach to the present has resulted in better utilisation, costs and safety and the computerised monitoring and control provides continuous awareness of machine and work conditions with the promise of future improvements.

Jan 1, 1991

By Palmer G, Dennis R, Clark A

The Ravenswood Mine in North Queensland is the first gold mine developed by Carpentaria Gold Pty Ltd, a wholly owned subsidiary of MIM Holdings Ltd. Carpentaria Exploration Pty Ltd began exploration at Ravenswood in 1978. However initial exploration of the main gold producing area (Buck Reef East) commenced in March 1987 when exploration rights to four key leases were secured. A rapid, co-ordinated exploration and development program produced gold from a heap leach operation nine months after the first costeans were dug at Buck Reef East. To treat higher grade ore found at depth in the Buck Reef East pit and the metallurgically more difficult Buck Reef West ore, a carbon in pulp plant was commissioned in May 1988. The mine is currently producing at a rate of approximately 40 000 ounces of gold per year. Ore at Ravenswood is hosted by hydrothermally altered diorites and tonalites of the Ravenswood Granodiorite complex. Alteration is controlled by planes of permeability formed by joints, shear zones and dilational breccias. The complex orebody geometry resulting from these controls required very detailed surface and drill exploration for adequate definition. Carpentaria's need for early cash flow meant that economic, mining and metallurgical considerations governed choices of exploration techniques, program timing, material and data collected. The initial reserve of 1.1 mt @ 2.87 g/t Au was defined by sectional polygonal methods. Grade control is based on geologic mapping and blast hole or channel sample assays. Ore is batched through the crusher and sampled to monitor grade control and mining performance. Minimal dilution has occurred. Gold content is greater than predicted by the reserve. Sprinkling of heaps commenced in November 1987. Changes have been made to the pad design and to the method of heap construction. Heap leach ore is treated at a rate of 400 000 tpa.

Jan 1, 1989

Mining software packages are used extensively in industry for resource estimation as well as for mine design and operation. Research undertaken in the W H Bryan Mining Geology Research Unit at the University of Queensland has shown that modifi

Jan 1, 1994

By M Andrew, D McTiffen, M Adams

A major Ventilation Upgrade Project commenced at the Fosterville Gold Mine (FGM) in 2017 to service the ongoing ventilation requirements of the underground mining operation. The project consists of three large diameter ventilation raises totalling 1100 metres, and new axial primary ventilation fans to upgrade the mine ventilation system. With a mining depth of 1200 metres and a thermal gradient of approximately 2.7 °C per 100 metres of depth, the completion of the Ventilation Upgrade Project is key to the ongoing success at FGM. The Ventilation Upgrade Project will allow continued mining, including high-grade gold deposits, lower in the mine where heat is increasing. Figure 1 below illustrates the underground workings at FGM, and provides a general view of the ventilation upgrade works to establish the new exhaust system from the lower workings to surface. Whilst raisebore pilot drilling the H4760 Return Air Rise (RAR) from surface to 395 metres, the raisebore drill string became stuck in the raisebore pilot hole at approximately 300 metres down hole, presenting a significant technical problem and delays to the project. This Case Study provides an overview of the recovery process undertaken at FGM including the recovery of the stuck drill string. The value of the stuck in-hole equipment, the investment in the shaft site preparation, the collar stabilisation, the underground development to the base of the ventilation raise, the surface footprint prepared for the Primary Fans construction and the limited available space on the site were all motivations to recover the raisebore drill sting and ultimately recover the ventilation raise location. More importantly, the long lead-time required should a new shaft location be the final solution, and the delay this would incur to the ventilation upgrade was unacceptable. Recovery of the drill string was not possible using the capability of the Contractor’s Raise Drill. An alternative method for freeing the drill string was required. A significant amount of engagement with industry was undertaken to seek out potential solutions and draw from the experience of others. All methodologies available were considered and assessed. Ultimately, after several attempts at freeing the raisebore drill string using various methodologies, Adams Drillers and Clear Cut Interventions were engaged to provide a turnkey recovery solution.

Mar 15, 2021

The paper, one of two papers on the Queensland Railways Brunswick Street tunnels presented at the VIII Australian Tunnelling conference, describes documentation, tendering and construction aspects.Tender documents were written to reduce the risk taken by the contractor. Details of tenders received are analysed and the changing industrial situation at that time described.Construction aspects covered include mobilisation, major equipment, tunnelling equipment and manning. Program and progress are reported including industrial relations and advance rates for Mitsui-Miike S-200 and S-65 roadheaders. Cycle times and performance in terms of cutting rate and pick wear are provided for the roadheaders.

Jan 1, 1993

By Schonert K

The throughput of a HP-roller mill is determined by the acceleration of the feed material within acceleration zone and introduction into the compression zone. Both processes depend on the internal friction and the friction of the material on the roller surface which is influenced by the surface structure and adhering of material. The particle motion in the acceleration zone has been investigated with high speed videos showing the effect of the centrifugal force and the slip on the roller surface. The throughput is discussed in the term of the specific throughput which can be approximated by a linear function characterised by the throughput number and the throughput elasticity. The throughput number is a helpful measure for investigating the influence of the feed material and the surface structure. The experimental results give some guidance for chosing an optimum corrugation profile.

Jan 1, 1993

By Lee H. G, El-Rahaiby S. K

The literature relating to reduction of sulphides by carbon using lime as sulphur-absorbent is reviewed. A stage-wise thermodynamic model is employed to evaluate the practical feasibility of the direct reduction smelting of galena (PbS) concentrates with a carbon reductant in the presence of lime; a coke-rate of 65 kg/ton Pb is predicted by the model. The experimental data on the reduction of PbS:4CaO:4C mixtures under nitrogen were correlated by means of a finite difference numerical method and the values of the intrinsic rate constant I1 were derived. The results for the uncatalysed reduction are represented satisfactorily with log I1 = 1.247(±0.522) - 5540(±610)T-1.The catalysed PbS:4CaO:4C mixtures contained 2.5 wt% of ternary (K, Li, Na)2CO3 catalyst. For the catalysed reduction it was found that log I1 = 3.981 (±0.301) -7790(±353)T-1, where I1 (in both relations) is expressed in moles.(g.C.)-1.atm-1.s -I. The catalytic enhancement faclor was found to be quite large in the 1068 to 1262°K temperature range investigated here.

Jan 1, 1991

The Hellyer deposit, hosted in the Cambrian Mt Read Volcanics, displays features typical of volcanogenic massive sulphide orebodies. These include a well developed stringer zone, metal zonation within the orebody, a polymict volcaniclastic sequence flanking the deposit and a hangingwall alteration plume in overlying basaltic pillow laves.Mapping and core logging is very detailed in order to extract as much data as possible from the deposit and its host rocks. A geological log suitable for direct computer input was adopted shortly after the deposit's discovery.

Jan 1, 1990

By Quinlan M. J, Ratcliffe J. S

Chemical kinetics is a dependent process which usually correlates the rate at which a reaction proceeds with the mechanism descriptive of the manner by which reactive particles interact. Given the latter, the object gen- erally is to find the reaction rate dependency in terms of an intensive property of the system - number of reactive particles present, and of the energetics of the system - usually temperature. Chemical kinetics depend on a dem- onstration that reaction considerations alone control the phenomenological process under study. For these rea- sons, chemical kinetics are usually involved in homogeneous gaseous systems. Even in liquid homogeneous sys- tems earliness or lateness of reactant mixing rather than chemical kinetics may be controlling. Considerations of transport phenomena are involved in heterogeneous systems and often control the observable rate:an additional problem in such systems is to apportion the rate due to mass transfer - usually a linear process - and that due to reaction which may be linear or non-linear. Experimentally, conditions are often chosen so that only one consideration controls but this becomes more difficult where solid phases are involved. Kinetic modelling involves considerations of chemical kinetics, transport phenomena, and factors attributable to the physical environment in which the process takes place. The latter two considerations may be quite different as between experiment and plant. The kinetic model may be a mathematical representation of a conceptual mech- anistic model of the reaction. Alternatively, it may be an empirical relationship resulting from, for example, some curve fitting procedure applied to experimental data. The latter approach may be necessary where the system is particularly complicated.

Jan 1, 1975

By Rosmus P

Improper use of auxiliary ven- tilation units during heading operations may often result in the appearance of hazardous methane accumulations. This is the case especially when roadways are ventilated by a combined system with a short sucking pipe at face end performing as the dedusting installation. Uniform air inflow to the face end facilitates sucking off the dust clouds and creates conditions favourable for formation of local methane accumulations. The highest methane concentration occurs in the cutting zone between the rock cut and the pipe inlet, under the roof and by, the sidewalls. Permanent monitoring of methane concentration at face end employs methane sensors. The most important are: one on the road- header's boom behind the cutting head, and one at the air outlet from the dedusting installation.

Jan 1, 1988

The Fosterville goldfield, situated 25 km east of Bendigo, Victoria was at its peak between 1894-1910 with some 47 600 ounces produced (Figure 1). Since that time intermittent mining and tailings retreatment was undertaken until Bendigo Gold Associates delineated a viable resource and commenced an open cut heap leaching operation in early 1991. Unfortunately they encountered financial difficulties and Perseverance Exploration purchased the mine in April 1992. Perseverance operated a successful heap leach operation nearby Nagambie, 100 km east of Fosterville. Based on its acquired heap leaching experience, Perseverance Exploration was able to instigate operational changes to create a successful small gold heap leach operation. The major change was the using of the original multi-use leach pad as a single-use leach pad. The available data allows for a comparison of the two operating systems.

Jan 1, 1994

By Kuganathan V

The processing of black coal in Australia segregates waste in the form of coarse reject and fine tailings. The coarse reject is relatively easy to handle, while the tailings can be problematic. Conventionally, the two waste materials are disposed of separately, the coarse reject in dumps, and the tailings in man-made containments. Aqueous tailings slurry is pumped to a 'wet' tailings storage, where the fine particle size of the tailings limits dewatering. Their low bearing capacity and high compressibility result in tailings deposits being difficult to rehabilitate. Disposing of the waste streams separately moves away from the heterogeneous mixture in the undisturbed ground, and concentrates potential problems with each waste stream. The feasibility and desirability of the co-disposal of tailings and coarse reject by combined pumping is demonstrated. This technique is in operation at Jeebropilly Mine and is proposed for a number of other coal mines.

Jan 1, 1992