Search Documents

THIS SYMPOSIUM ON AUSTRALIAN BEACH SANDS IS MOST TIMELY; WHEN WE ARE APPROACHING PEAK PRODUCTION FROM THESE RESOURCES AND WHEN PRICES ARE GOOD, BUT THE RESOURCES CAN BE SEEN TO BE COMING TO AN END IN THE LIFETIME OF OUR YOUNGER COLLEAGUES - 20 TO 25 YEARS AS WE HEARD FROM ROY TOWNER TODAY. THE SPREAD OF PAPERS HAS BEEN 15 PERCENT EACH ON GEOLOGY AND THE MINERAL RESOURCES, WITH 25 PERCENT ON LAND USE AND ENVIRONMENTAL PROBLEMS. I AM PLEASED TO SEE 20 PERCENT HAS BEEN ON TREATMENT PROCESSES AND 25 PERCENT HAS BEEN CONCERNED WITH DOWNSTREAM USES. I SUSPECT THESE RATIOS ARE DUE IN PART TO THE WAY PAPERS WERE CALLED FOR, BUT THEY ALSO SUMMARISE CLOSELY THE BALANCE OF INTERESTS IN THE INDUSTRY. NOTE AGAIN; 30% CONCERNED WITH SUSTAIN -ING RESOURCES, BUT 25% WATCHING LAND USE AND IMPOSING CONTROLS; 20 % IMPROVING THE PRESENT PROCESSING, AND A HEALTHY 25% WITH AN INTEREST" IN WHAT HAPPENS TO THE MINERAL CONCENTRATES. I SHALL RETURN TO THIS FOURTH POINT AT THE END OF MY REMARKS. THE POSSIBILITY OF ADDITIONAL HEAVY MINERAL SANDS IN NEW AREAS WAS HINTED AT BY M.S. SHEPHERD (EG TERTIARY SHORELINES OF THE MURRAY BASIN). OLD FOSSIL SHORELINES, WELL REMOVED FROM PRESENT SHORES ARE AN IMPORTANT MINERAL SOURCE IN CHINA AND IT WOULD HAVE BEEN INTERESTING TO HEAR FROM THE SEVERAL COMPANIES EXPLORING IN THE MURRAY BASIN. I ALSO NOTICED THAT WHILST OUR MONAZITE

Jan 1, 1986

By J A. Sanchidrián

The general ranges of validity of some distribution functions are assessed from their behaviour with 119 sets of fragmentation data from bench blasting obtained by sieving. The emphasis is on determining the lower size/passing limit that the size-scaled Rosin-Rammler, Grady and Swebrec functions, and their bi-component versions, can represent with reasonable precision. By fitting these functions to the data using different weights, the accuracy of the fit varies in the different size/passing zones, so that an overall knowledge of the capacity of the function is obtained across the whole size range, from the coarse zone to the fines. Reasonable ranges of use of bimodal Rosin-Rammler and extended Swebrec (all of them five-parameter, bi-component distributions) are, in terms of percentage passing p, 99 > p > 2 per cent (up to 100 per cent for the extended Swebrec), or 90 > p > 0.5 per cent, in which the expected error of the calculated size is below 15 per cent in the extremes of the range, and less than five per cent in most of the central range; maximum errors (ie errors that will only rarely be exceeded) are typically less than 50 per cent in the central range, and up to about 100 per cent in the extremes. Ranges of use for the Swebrec and the size-scaled Rosin-Rammler (three-parameter distributions), with only slightly larger errors than the bi-components, are 100 > p > 5 per cent or 80 > p > 2 per cent. The classical two-parameter Rosin-Rammler can be used in the range 95 > p > 20 per cent or 90 > p > 10 per cent, with expected and maximum errors less than about 15 per cent and 100 per cent respectively.CITATION:Sanchidrián, J A, 2015. Ranges of validity of some distribution functions for blast-fragmented rock, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 741–748 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By P K. Wong, D A. F Oliveira, F M. Azad

In situations where foundation piles are located in proximity to existing or future tunnels, it is typical for the tunnel owner to require that sleeving of the piles be carried out to at least the invert of the tunnels to minimise any load transfer to the tunnel lining. In competent rock, this practice may be sometimes unnecessary, thus uneconomical. This paper presents an assessment of the effect of pile loading from one of the multi-storey buildings at Barangaroo South in Sydney on the adjacent future Sydney Metro tunnels. It was originally required by Transport for NSW (TfNSW) that the piles be sleeved below the tunnel invert level; however, the building developer wanted to reduce the pile sleeving depth to achieve a more economical solution due to the large number of load transfer piles being required for the project. To assess this feasibility, a full 3D commercial numerical code, FLAC3D, was used to carry out this complex soil-structure interaction analyses. Based on these assessments, it was demonstrated successfully to the TfNSW that the pile sleeving may be terminated at 2 m above the tunnel invert level. For this arrangement, the investigations found that the loading on the piles should have negligible adverse impact on the tunnel lining design. As a result of such an assessment, the proposed pile sleeving level was approved by TfNSW, thus offering an economical foundation solution for the project.CITATION:Azad, F M, Oliveira, D A F and Wong, P K, 2014. The impact of pile loading on adjacent metro tunnels – Barangaroo South, Australia, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 355–360 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By M I. Pownceby, N Karimian, J R. Manuel, M J. Peterson

The CSIRO ore classification scheme for Pilbara ores was used as a reference frame to target recognisable ore types/textures with potentially elevated phosphorus content for detailed analysis. Particles of each individual ore texture were separated from a Brockman high-P ore and each class was characterised using methods including XRF, XRD, EPMA and synchrotron-based XAS. Results were then correlated with optical microscopy and hand specimen identification to establish any relevant associated mineralogical phases and/or textures. This represents a more systematic approach to identification of high-P ore components based on particle and goethite type and texture. The information can then provide the basis for more targeted P-removal strategies factoring in the relationship between particle/ore texture and phosphorus deportment

Sep 18, 2023

By M Berndt

Four siltite-argillite rock samples were characterised (particle size, chemistry, mineralogy) and subjected to laboratory dissolution testing for 36 to 298 weeks. In two samples sulfur (0.99, 1.69 wt per cent) occurred largely as pyrite, and in the other two samples sulfur (0.96, 1.93 wt per cent) occurred predominately as potassium jarosite. The observed rate of sulfate release from the pyritic samples was one to two orders of magnitude greater than that from samples containing potassium jarosite. Drainage pH values from the pyritic samples were one to two units lower and acidities were ten to 70 times higher than associated values from the potassium jarosite samples. Geochemical modelling supported the hypothesis that pH and concentrations of sulfate and potassium in drainage from the potassium jarosite samples were controlled by the limited solubility of potassium jarosite. This dissolution produced an iron-dominated mineral phase, but iron concentrations in the drainage were well below those predicted by ferrihydrite solubility.

Jan 1, 2003

By Sano S, Ishikawa T, Nagaoka H, Hayashi Y, Hasegawa M

The stirred mill is regarded as one of the most efficient devices for micronising materials and has come to be actively used for preparation of fine particles. Recently, the demand for ultrafine particles was increased in many kinds of industries. In this paper, autogenous grinding to get submicron particles based on mutual friction feed material has been carried out using a stirred mill. The mill used was made of stainless steel and its volume was about 5.5 litres, and has 12 impeller blades. Sample used was limestone. In the present work, two operating parameters such as stirring speed and feed size of limestone were considered. The ground products were sieved in the size range from feed size to 325 mesh (45 lun), and from 45 to 0.17 pm the size distributions were measured by a laser diffraction and scattering method. The progress of grinding was evaluated by the increasing amount of submicron particles in products. As a result, the rotational speed of impeller with the minimum energy consumption to produce submicron particles was observed. It was found that the autogenous grinding with a stirred mill is an effective method for producing submicronized limestone.

Jan 1, 1993

By M Bond, R R. Hargreaves, G W. Booth

There are numerous causes of speculative mineral resource and reserve inflation. Traditionally, these are linked to issues of data accuracy or misinterpretation, the use of overly optimistic estimation parameters or assumptions, an absence of independent expert verification, or the simple pressure to increase company value, covert or otherwise. Owing to its subjective nature, classification of resources and reserves remains an opaque process. Of necessity, Competent Persons rely on personal heuristic interpretations, ideally underpinned by appropriate estimation and classification experience across commodity and deposit types. Whereas independent verification of individual resource and reserve statements remains impractical, publicly available data can be interrogated for potential category inflation, particularly when viewed with exploration expenditure statistics included in annual company reports. Abrupt changes in category tonnages and market capitalisation without concomitant expenditure can aid in outlier detection. Consequently, a comparison of common exploration and resource reporting parameters offers a basis for risk assessing classification robustness, over time. In this introductory study, an analysis of globally listed companies was undertaken over a multi-year period, examining base and precious metal projects in both preproduction and operational asset classes. From these, a series of exploratory decision tree trigger points were generated against which target companies were anonymously identified and risk-ranked.

May 24, 2023

By Matthew SP, Hayes PC

The product morphologies formed on the reduction of dense wustite crystals are classified into three types,A) porous iron, B) porous wustite covered with dense iron and C) dense wustite covered with dense iron. The mechanisms of formation of these structures and the effects of impurity elements on the product morphologies are discussed

Jan 1, 1984

The radiolarian biostratigraphy of the western part of the Gympie Province, north of Brisbane, has been examined. This part of the province comprises mainly the Amamoor beds and the Gympie Group, which have been assigned Permian ages on the basis of localised marine macrofossils. This study has shown that the Amamoor beds and the Gympie Group include older strata than previously supposed.The Amamoor beds consist of at least two tectonic units, namely a melange unit (unit A) and a well stratified sequence of sedimentary rocks (unit B). The former unit, regarded as an accretionary subduction complex, contains chert blocks ranging from Late Devonian to Earliest Carboniferous, while the latter unit yields Permian radiolarians. Latest Devonian to Earliest Carboniferous bedded cherts occur in sequence previously mapped as Amamoor beds and Gympie Group.

Jan 1, 1990

By Ward M

The current and future requirements for an underground mine information management system are being met with a flexible, value-engineered approach to mine information/communication infrastructures. El-Equip has developed and delivered to over fifty mines around the world an integrated, high capacity, radio-based leaky feeder communication system called MultiCOM. To meet the requirements of recently developed advanced information management technologies, such as production and ventilation management, the system has evolved to support simultaneous mobile and fixed information delivery services over an integrated single cable system. The following paper will review how MultiCOM is enabling information/communications technology to cost-effectively implement mine monitoring and control applications. Applications described in this paper include mobile vehicle production tracking, vehicle location, ventilation system monitoring and control with integrated ventilation system simulation. The techniques described are leading the world in terms of flexible and value-engineered applications of technology in the underground mine.

Jan 1, 1995

The amount of land subjected to coal surface mining in the United States has been reported at 1, 302, 000 acres (1). Latest National Coal Association estimates (1968) show that about 65, 000 acres are affected annually in the production of 186, 000, 000 tons of coal. Peabody Coal Company affects approximately 9500 acres annually in the ten States in which we are presently operating. Surface mining at Moura, Australia was begun in February 1961. In Marcy 1963, the Marion 7900 dragline with 35 cubic yard bucket went into operation and in 1967 the Marion 8900 dragline with a bucket capacity of 130 cubic yards was put into operation. In addition a third dragline, a 480W was added in 1969. It carries a 15 cubic yard bucket and is used to work areas that are too small to justify movement of the larger machines, In 1969 the Moura surface mine produced 3, 002, 774 short tons, and in 1970 3, 418, 933 short tons.

Jan 1, 1971

Scheduling mine development and underground construction has been the bane of most mine managersÆ lives at one time or another. Even though scheduling software has developed significantly over the last 20 years, mining projects continue to take far longer than expected to complete. It would appear that possession of a gleaming 1000 activity bar chart generated by the latest project management software and plotted in multiple colours offers no guarantee at all that any of those 1000 activities will be completed on time, let alone the project as a whole. The author has earned his æmasters in disastersÆ with more than one project running over time and budget. This paper describes some of his experiences in scheduling major mine development and construction projects and the lessons he has learnt along the way. In particular, the paper examines a range of key issues that mine schedulers must take into account when planning mining projects. The paper also examines the development of scheduling software and particular advance rates used in scheduling mine development projects in Australia.

Jan 1, 2000

By G E. Smith, G N. Lye

Wall control blasting practices are necessary to reduce the impact of blasting on mine faces but can also have a significant negative impact on mine productivity and operating costs. The conventional practice in deep open pit mines is to use so-called trim blasts adjacent to pit walls. To provide burden relief these trim blasts have fewer rows than full production blasts and are fired to a cleared free-face; hence they are termed æunchokedÆ. This practice leads to scheduling constraints on the pit operations and can cause ore dilution due to excessive muckpile movement. The use of such trim blasts stems from the perception that increased wall damage results from æchokedÆ blasts. These concerns are based on the unproven assumptions that blast vibration levels and explosive gas penetration increase with increased blast burden and face confinement. This paper describes work undertaken as part of a major investigation into wall control blasting at the KCGM Fimiston Mine, Kalgoorlie, Western Australia. It details a study to assess damage effects due to blast burden. Borehole air pressure measurements and borehole video camera inspections were done behind a series of single blastholes drilled with varying burden distances, as well as behind a dedicated trim blast and a full production blast. It was found that the measured damage effects, including visible rock cracking, dilation, and the limited extent of gas penetration behind the blastholes, did not vary significantly with burden or blast type for the cases tested. This result was in complete agreement with detailed vibration measurements conducted by Blair and Armstrong (2001) during the study, which found that vibration was independent of blast burden. As a result of these investigations, changes to the blasting practices at the mine were implemented. Dedicated trim blasts and free-face blasting have been replaced by modified production blasts and the practice of æchokingÆ blasts has been introduced. This has resulted in a significant improvement in productivity and cost savings without compromising pit wall integrity.

Jan 1, 2001

By A Weeks an, R Bertinshaw, S Khosrowshahi

Good mining is central to any approach to value tracking. Good mining occurs where the ore is correctly delineated, measured and fed to the mill. This process is usually referred to as grade control, ore control or quality control. There are now ways to measure the efficiency of this process, such as by using conditional simulation, and a brief synopsis is presented. Resource estimation is the foundation of ore reserve estimation, which should enable useful prediction of the expected metal to be recovered from mining and milling. Significant improvements have resulted from applying new techniques such as the Chain of Mining (CoM) method, which models the mining process. Again, a brief synopsis is presented. Tracking value from the mine through the mill implies a linear sequence of processes that can be modelled. Reality is more complex and there are error components, feedback loops and breaks in the Chain of Value. Modelling the total production process in a number of operations is considered, including the various impacts on producing reconciliations. Procedures are also discussed for handling a number of difficult issues such as: different data supports, stockpiling strategies, blending from multiple ore sources, blast movement and underground ore extraction.

Jan 1, 2002

By E Ruhanen, S Kauvosaari, M Kosonen, C Meintjes

The Yara Siilinjärvi plant is located in the central part of Finland. Siilinjärvi is Western Europe's only apatite mine and annually it produces 1 Mt of apatite concentrate, which creates approximately 10 Mt of tailings.At the beginning of 2017, tailings handling in Yara Siilinjärvi was brought to a new era, by replacing the conventional tailings storage facility with a new tailings treatment plant. The new high-density tailings disposal system with two paste thickeners increased the percentage of solids in the slurry from 45–48 per cent to 66-68 per cent, making it possible to deposit as a paste. This extended the life-span of the current tailings storage facility by 15 years; from 2020 to 2035.This paper presents the storyline of the Yara Paste Plant Project. The project began with laboratory testing and then progressed to pilot-scale thickening and beaching trials. After some successful pilot trials, the final process design was implemented. Process instrumentation and automation played a key role in the project, as the aim of the Yara Project was to make the plant operable remotely from the main plant. An advanced control system is needed to maintain process stability and the desired operation point in various operational circumstances.This paper discusses the results from the Yara site since the new tailings treatment plant commenced. Some of the main points are that the operation has been running consistently with an underflow solids content of 66-68 per cent, with average beach slope angles of 3.5 degrees in the tailings disposal area. This control system additionally facilitates minimum use of flocculant, which delivers significant savings to operating costs. Robust thickener operation also leads to the trouble-free high-density pumping and high availability of the Paste Plant. During the first year of operation, the plant’s availability has been very good, over 97 per cent.Currently, the plant still has its own staff working there during the daytime, but the Paste Plant is now already operated remotely during the night shifts. The long-term goal is to gradually transition into operating the plant completely remotely.CITATION:Ruhanen, E, Kosonen, M, Kauvosaari, S and Meintjes, C, 2018. Optimising the operation of paste thickening at the Yara Siilinjärvi Plant, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 297–310 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By L M. Zhang, T H. Xu, J Zhao

Blasting is one of the most commonly used strategies for excavation in civil and mining engineering. Yet blasting can also bring along such undesirable effects as ground vibrations and soil disturbance. Numerical analysis is a powerful tool for estimating the effects of blasting and improving blasting design. In this research, a constitutive model for sand is proposed for the numerical analysis of blast-induced ground motions and wave propagation in soil mass. In the model, three model surfaces, ie the critical surface, the dilatancy surface and the bounding surface, are defined following the bounding surface hypoplasticity framework. The strain rate is included explicitly into the model formulations so that the proposed model is valid under high strain rate loadings caused by blast-induced vibrations. The performance of the proposed model is validated by the simulation of drained triaxial compression tests conducted on a crushed coral sand under different strain rates.CITATION:Xu, T H, Zhang, L M and Zhao, J, 2014. A bounding surface model for sand subjected to blast-induced vibrations, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 201–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By O Pasca, B Hogg

Consistent slag blow end point detection remains one of the challenges in the Peirce-Smith converters at Mount Isa MinesÆ Copper Smelter. Under blowing results in foaming on copper blow and carry forward of oxide skims to the anode furnace. Over blowing results in high copper losses to the slag. Both present safety issues and contribute to lower copper production. The end points of the slag making phases are assessed by inspection of a bar sample. A bar sample is a thin accretion layer that adheres to a steel bar when it is inserted into the tuyere while the converter is blowing. This method is biased and subjective, so there is heavy reliance on operator experience. The Semtech Optical Process Control (OPC) system was installed in early 2002 for converter slag blow end point detection. Initial plant trials did not improve all aspects of converter operations, and uptake by operators was poor, so the system was not used. In early 2005, the Semtech OPC system was re-visited and another short trial was conducted to evaluate the permanent use of the system for slag and copper blow end point detection. During this trial, the Semtech OPC method was found to be superior to bar sampling for slag blow end point detection. The implementation and refurbishment of the Semtech OPC system has resulted in plant improvements and given a better insight into converter operation during blowing. Oxide skim generation carried forward to the anode furnace has been shown to decrease with increasing compliance with Semtech OPC. Some of the expected improvements to converter operation were not found to be significant. Semtech OPC is now well received and utilised by converter operators. Individual paper available only. Not included in book or CD ROM Proceedings.

Jan 1, 2005

By J O. Okonkwo

AngloGold operates various gold mines in South Africa, the largest of which are situated in the North West province. The impact of AngloGold Vaal River mining operations on the environment and, specifically, on aquifers and groundwater is assessed. The location of such aquifers and plumes is determined by remote-sensing and ground-sensing operations, followed up with the correct placement of monitoring boreholes from which information such as water rest levels, chemistry and geological data is gathered. This study utilises an integrated approach consisting of the following mutually reinforcing phases: Phase 1: Airborne multi spectral scanning; Phase 2: Airborne thermal remote sensing; Phase 3: Ground resistivity survey; Phase 4: Borehole placement; and Phase 5: Sampling and monitoring. The integration of the investigation tools and phases in use at AngloGold Vaal River has been found to be very useful in determining the exact sources of contamination, the direction of flow of such contamination, the positioning of interceptive measures and the analysis of such contamination. This adopted approach will enable the development of flow transport models that will further enhance our knowledge of contaminants in aquifers at the mine and enable management to conduct educated interventions.

Jan 1, 2003

By G Brewster

The Eagle on the Hill tunnels form part of an upgrade of Mt Barker Road, 15 km to the southeast of Adelaide. The upgrade significantly improves safety and reduces delays on this major road, which winds steeply through mountainous terrain. The twin tunnels each spanning 15 metres run in parallel for a length of 480 metres. The tunnels are excavated in slightly weathered high strength slates and very high strength quartzites of the Saddleworth Formation on the western margin of the Mount Lofty Ranges. Steeply dipping slate cleavages and the high fracture ratio result in many slope stability problems in the project area. The level of geotechnical investigation undertaken prior to the calling of tenders for the project was extensive. This included the excavation of a pilot tunnel along one of the tunnel alignments, which allowed accurate mapping and rating of the rock, resulting in an increased level of confidence during the tender process. One of the features of the winning alternative tender design was the use of canopy tubes, flexible steel ribs and shotcrete to replace up to 40 metres of deep portal cuts in unstable rock with driven tunnels. Slope stability issues were overcome with the use of rock dowels and shotcrete. The support concept allowed the safe driving of the tunnel portals with as little as two metres of overburden. The design incorporated lining drainage and criteria for fireproofing based on European experience to ensure the ability of the tunnels to remain stable in the case of a severe fire incident. The support design allowed for maximum flexibility with a range of support types able to deal with the varying ground conditions. Design development and support refinement continued throughout the tunnel construction phase with close liaison between the designer and the constructor. Monitoring and review of feedback from the construction site by the Sydney based design team was easily achieved by means of electronic transfer of photographic and survey information, telephone and fax communication and regular site visits. The contractor for this project is Macmahon Concrete Constructions Joint Venture (MCCJV) and the designer is Connell Wagner. Excavation commenced in January 1998 with tunnel breakthrough having been achieved in early-August 1998 and mid-September 1998 respectively. Concrete lining construction is scheduled for completion in April 1999.

Jan 1, 1999

By L Smith, R Beckie

Controls on environmental loading from acid rock drainage (ARD) are not well understood in waste rock material. In particular, relationships between subsurface flow and the timing, duration, and intensity of leaching of metals and acidity from waste rock dumps remain ill defined. This study investigates field-scale relationships between subsurface flow processes and geochemical processes in unsaturated waste rock. A 12-metre tall, unsaturated waste rock pile, constructed in 1994, was deconstructed and sampled at Key Lake, Saskatchewan, Canada, during the summer of 2000. A detailed sampling methodology was developed to characterise physical and chemical properties of waste rock material within the waste rock pile. Physical properties were characterised by measuring soil-water suction, volumetric water content, and grain-size distribution at 60 random locations within the pile and grain-size distribution at 20 grid locations within the pile. Attempts to develop a field-based soil water characteristic curve from physical field-data failed due to spatial variability and hysteresis of waste rock properties. As a result, grain-size distribution was used as a relative measure of subsurface flow. Paste pH, pore-water geochemistry, mineralogy, and water-soluble extraction results were used to characterise geochemical processes and sulfide oxidation at each of the 20 grid locations. Geochemical characterisation results demonstrated the preferential weathering of marcasite relative to pyrite and chalcopyrite. Dolomite was the main buffering carbonate mineral. Gyspum, jarosite and iron oxyhydroxides were the main secondary minerals. Pore-waters contained up to 800, 11.7, and 6 mMolar (78 000, 690, 1400 mg/L, respectively) of sulfate, nickel, and uranium, respectively, suggesting significant weathering has occurred. Measures of weathering indicators show no discernable correlation with grain-size distribution nor do they show any spatial relationship within the sampled grid. Reasons for this may include limited duration of waste rock exposure to weathering and development of fluid flow-paths, and limitations of characterisation methods used. Indeed, six years may not be long enough for weathering patterns to develop due to fluid flow-paths in this unsaturated waste rock pile.

Jan 1, 2003