Search Documents

By Z Lianbi, Z Yibin, Z Youhong, P Bin

Without adequate soil available, it is difficult to rehabilitate a large area of acid mine waste dump with sustainable plant communities, which has a strong potential acid generation. In the present project, paste tailings capping method has been put forward to reconstruct plant ecosystem on acid mine waste rock dump. This rehabilitation method uses paste tailings as capillary break and plant growth media. The tailings used contained 26.3 per cent of particles of less than 20 ¦m which satisfy the requirement of grain of paste tailings preparation. The tailings are not acid- producing materials. In addition to Cu, total contents of Zn, Pb, Cr, Cd, As and Ni in tailings are lower than those in local soil. Paste tailings concentration 70 per cent ~ 72 per cent was prepared by concentrating ten per cent tailings by using polypropylenecrylic sodium as flocculation. The potential pollution risks are low by using paste tailings as capillary break layer. Plants directly grown in the tailings did not particularly accumulate Cu, Zn, Pb, Cr, Cd, As, Ni in roots, stem and leaves, which were 0.01 ~ 1.6 times of those grown in soil.CITATION:Yibin, Z, Lianbi, Z, Bin, P and Youhong, Z, 2012. Study on paste tailings capping ecology reclamation on acid mine waste rock dump, in Proceedings Life-of-Mine 2012 , pp 243-246 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By Kavetsky A, Scott A

As well as breaking and moving rock, blast energy sets up a seismic wave in the ground which can cause significant damage to rock structures and buildings and disturbance to human occupants. This seismic ground vibration is potentially most damaging when its dominant frequency coincides with the resonant frequency of a structure, leading to high amplification factors between the input ground vibration and the resulting structural response. This paper outlines methods of identifying the resonant frequency of structures. It also describes a practical numerical method for the modification of blast designs to reduce the ground vibration energy in critical frequency ranges. The method is illustrated with two recent case studies.

Jan 1, 1990

By Bowling K. McG, Hamilton J. D G

The influence of three important para- meters which affect the induration of iron-ore pellets, viz temperature, time, and lime content, have been assessed in terms of internal pellet structure and commonly-used pellet quality criteria. The pellets studied were produced from a typical hematite ore from the Pilbara area of Western Australia, using a 25 cm dia. pot-grate test rig. Isothermal laboratory induration tests were conducted in accordance with a statistically-planned programme. The internal structures were studied by optical microscopic examination of polished sections of the test pellets. The effects of SFCA (silico- ferrite of calcium and aluminium) and slag formation, matrix consolidation and grain modi- fications were studied, and have been related to pellet properties and to the time/temperature histories produced by the firing conditions chosen. The implications of the data for commercial pellet plant operations are discussed.

Jan 1, 1974

By C Mark, Z Agioutantis

This paper presents an empirical design methodology that is based on successful US roof support systems using both primary and secondary support in coal mining entries and intersections. The recent nationwide dramatic reduction of roof fall rates, especially in areas with weaker roof, can be directly correlated to the effectiveness of the roof support systems. A large database of roof fall histories at several mines is used to define the approximate boundaries of three modes of roof support with respect to roof strength as classified by the Coal Mine Roof Rating (CMRR) and in situ vertical stress as indicated by the depth of cover. These roof support classifications are: • Suspension, where roof bolts mainly provide skin control for strong roof. • Beam building or reinforcement, where a roof of moderate strength can be supported by roof bolts only. • Supplemental (secondary) support, where the primary support by roof bolts may be augmented by several secondary support systems, eg cable bolts, trusses, additional roof bolts or standing supports. The Primary Support Rating index (PSUP) captures the capacity of the primary roof bolt system as a function of the actually implemented roof control plan, ie roof bolt length, roof bolt density, and roof bolt capacity, while it does not consider the type of bolt. The actual PSUP value is compared against a suggested PSUP value derived from statistical analysis of US case histories. Where secondary support is indicated, the expected rock load determines the necessary capacity of the secondary support system. A new (free) software package, Analysis of Mine Roof Support (AMRS), implements the design methodology and also allows comparison with other international indices such as the Reinforcement Density Index (RDI), the PRSUP, etc.

Nov 29, 2022

By A E. Annels, M D. Raine, I M. Platten

Lode-gold systems are often characterised by a high to extreme nugget effect (>50 per cent), and the presence of coarse gold particles (>100 ¦m in size). They rank amongst the most difficult of ore deposits types, in terms of producing an accurate and precise resource estimate. Their effective sampling is generally difficult because of the relatively low concentrations involved and erratic nature of the gold particles. Grade continuity is usually less consistent than gross geological continuity, and is typified by the localisation of grades within discrete oreshoots. In most cases drilling, particularly diamond drilling is an effective measure of global geological continuity, whereas grade can only be reliably resolved from underground development. Depending upon drill density and geology, it is unlikely that anything above an Inferred Mineral Resource can be estimated from surface drilling alone. Underground development, in-fill drilling and, potentially, bulk sampling or trial mining will be required to delineate Indicated and Measured Mineral Resources and subsequent Ore Reserves. Grade estimation will have to account for highly skewed and often multi-modal populations, extreme values, a high nugget effect and low geostatistical ranges. A clear geological model that honours both geological and grade continuity must drive the resource estimation process.

Jan 1, 2003

By Y Durkheim, P Saunier, L Ameglio

"In the last decade Afitex developed the Draintube™ geocomposite, which provides simultaneous drainage and waterproofing functions. This new type of drain tubes planar geocomposites (DTPG) differs from other geocomposites as the drainage core is composed of multiple corrugated and perforated pipes instead of biaxial or triaxial nets. It is furthermore associated with needle-punch stitched layers of non-woven geotextiles, which act either as capillary mediums or as filters.In this paper, the structure of the Draintube™ drainage composite is presented along with its key properties and the drainage mechanism associated with its particular structure.The relevance of this kind of structure is then reviewed based on past and current laboratory bench evaluations and field installations for mining applications such as the covering of acid rock drainage (ARD) tailings for the Central Manitoba Mine (Canada) site-rehabilitation; and as a pregnant solution collection layer in heap leach pads.Some of the demonstrated critical advantages of Draintube™ in the mining industry are as follows: reduction of the thickness, hence lower volume of granular drain layers improvement of fluid and gas collection and reduction of the hydraulic load reduction of secondary collector network mechanical protection of the sealing membrane fast and economical installation of interlifts stability under extreme conditions (compression, temperature, pH) increased stability of entire covering system and reinforcement of protection of dykes filtration of the covered material customised drainage positive connection of the geocomposite to collector pipes enable leaks detection (using a conductive textile layer) with an electrical test.CITATION:Saunier, P, Ameglio, L and Durkheim, Y, 2015. Tubular drainage and lining geocomposite for mine tailings and heap leach pads, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 297–304 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 27, 2015

By A Salama, J Greberg, B Skawina

In today’s underground mass mining, the orepass is an important part of the infrastructure as it connects two or more mine levels and is used for conveying or storing large amounts of material. One of the main risks related to an orepass is when operational or structural failure occurs, leading to long-term loss of functionality. Developing or rehabilitating an orepass when major failure has occurred is a time-consuming and expensive operation, and the risk of a long-term orepass loss motivates the development of alternative transportation strategies to ensure the continuation of smooth operations in large underground systems. The study presented in this paper has been done at the Loussavaara Kiirunavaara AB Malmberget mine in Sweden, where iron ore deposits are being extracted using sublevel caving. The study analyses the transportation system in one of the mine’s orebodies using discrete event simulation, with a focus on maintaining ore transportation in the event of the loss of an orepass.CITATION:Skawina, B, Greberg, J, Jonsson, K and Salama, A, 2016. Orepass loss mitigation approach in Malmberget mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 617–622 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By V Gumba, S Narendranathan, C Barker, R D. H Thomas, G P. Bungard

This paper presents the positive outcomes on an EPCM project, which was undertaken in a challenging environment, whereby the design team had to generate a design with a number of stringent serviceability criteria, any deviation from which would have had significant implications to the proposed design performance. The success of the design implementation within the tight time frame hinged upon the precise installation by a skilled contractor. The overall objective was achieved as a result of close collaboration between the designer and contractor ensuring all stringent quality assurance/quality control (QA/QC) aspects were met and opportunities to optimise design without compromising on performance were identified and implemented, resulting in a cost saving of over A$13 M.CITATION:Narendranathan, S, Thomas, R D H, Bungard, G P, Gumba, V and Barker, C, 2012. The importance of collaboration between designers and contractors in implementing a design in challenging conditions, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 97-102 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

The Que River and Hellyer polymetallic massive sulphide ore bodies are located 3 kilometres apart in the Cambrian Mount Read volcanics of Western Tasmania. Both deposits are classic examples of the Kuroko volcanogenic style. Base and precious metal rich hydrothermal solutions rose through a deep fracture system and vented on the sea floor, causing sulphides to accumu- late in adjacent topographic lows. Together the preproduction geological resource is approximately 23 million tonnes at greater than 18% zinc plus lead, with economically significant silver and gold. Exploration by Aberfoyle in the Mount Read volcanics com- menced in 1970. Que River was discovered in 1973 following a comprehensive data review, a regional stream geochemical survey and a helicopter-borne electromagnetic survey. Production began in 1981, and the mine is currently producing 300,000 tonnes per year. The ore is sold to the Electrolytic Zinc Company of Aus- tralasia Ltd mill at Rosebery. Ten years of extensive geological mapping, soil geochemistry, and induced polarisation, combined with continual study of the Que River orebody and its host rocks, formed a strong frame- work for the discovery of the Hellyer deposit, which was found as a result of drilling .a subtle time domain electromagnetic anomaly in 1983. Hellyer is currently being mined at a rate of 250,000 tonnes per year, with the ore being concentrated at Aber- foyle's converted Cleveland tin mill. Treatment of 1 million tonnes per year will begin in early 1989 at a new mill located near the Hellyer site.

Jan 1, 1988

By Higuchi K

Intorducing the hypothesis that the cause ,òi spontaneous combustion of coal is depending un the accumulation of heat produced by its oxidation, the authors derived the equation expressing the temperature change in a heap i fine coal. To solve the equation, thermal conductivity, specific heat and rate of heat ,eneration of fine coal (-48 mesh) were measured at various temperatures in the range _'0-65¦C. The equation was solved numerically and the volume of fine coal which would ignite spontaneously was estimated as the function of ambient temperature. Using 170 Kg of fine coal, everal experiments for confirmation were conducted. At the ambient temperatures of 60¦C nd 50¦C, coal began to fire spontaneously brut 00 and 110 hours later respectively. Iii addition to this, the measured t,,rp,i,itures in the coal heap agreed with the ,aLulated ones comparatively well, If more volume of fine coal were used, experi;:ontul ;,eneration of spontaneous combustion from ...,n-, , 1-1 I'd Sill al r..

Jan 1, 1981

By A Stasi, B Brice

Water is a limited and precious resource in Australia. Because of the increasing demand for water from all sectors of the economy and the variability in supply, efficient management of water resources is of vital importance. The national water reform agenda has provided a strong impetus to all states and territories to progressively move towards more efficient and sustainable water management. The Queensland Water Act 2000 is the legislative framework for providing water for the environment and for planning for the security of supply to water users. The comprehensive water planning process prescribed in the Act results in new tradeable water allocations that are separate from land. These water allocations are well specified and can be traded on a permanent or temporary basis. Trading of water allows it to move to its highest value use, thereby encouraging the most efficient distribution of this limited resource. In addition to transferring ownership of water allocations, it is also possible to change the attributes of the allocation, such as the location from which water may be taken. Changes to water allocations are subject to approval from the resource manager. Pre-testing allows for certain changes to be approved very quickly, making the trading process more streamlined and cost effective. Temporary trades, or seasonal water assignments, currently account for the majority of water trades in Queensland. However, permanent trading activity is expanding steadily as old water entitlements are converted to tradeable water allocations and as the market matures. The permanent trading market provides significant opportunities to the mining sector. It allows mining companies to buy water allocations at market prices without compromising environmental outcomes or causing third party impacts.

Jan 1, 2006

By C M. Ramotsabi, F Bornman, W Erasmus

Spiral concentrators are gravity based separation devices used for the preparation of coal, iron and heavy mineral ores (Wills, 1992). Gravity concentration remains the main separation method for fine iron ore and is used extensively for treating many minerals. Gravity concentration methods separate minerals of different specific gravity by their relative movement in response to gravity and one or more other forces, the latter often being the resistance to motion offered by a viscous fluid such as water or air (Wills, 2006).The main operating variables for a spiral concentrator are the feed rate, the slurry concentration, the wash water addition and the position of the splitters used to separate the tailings, middlings and concentrate streams (Sadeghi, Bazin and Renaud, 2014). Wash water is an important control variable used to wash away entrapped light minerals from the concentrate stream (Burt, 1984; Bouchard, 2001). Sadeghi et al concluded the spiral operation to be sensitive to the wash water flow addition and resultant economic trade-off. Increasing the wash water flow rate increases the concentrate grade at the expense of the iron recovery.The paper addresses the effects of dripping wash water onto the concentrate stream of a spiral processing fine iron ore. The dripping wash water system offers a low flow alternative and could possibly provide a good balance between grade and recovery of valuable minerals without using excessive water. The Multotec SC20HC/7 WW spiral was used for the experimental test work. The spiral was tested at varying solids concentrations; the wash water rate and the splitter positions were kept constant.The use of wash water at 30 per cent, 35 per cent and 40 per cent solid concentration improved the Fe grade in the concentrate by about 1.5 per cent, six per cent and eight per cent respectively. The additional SiO2 rejected by the wash water is approximately three per cent, nine per cent, and 11 per cent at 30 per cent, 35 per cent and 40 per cent solid concentration respectively. Addition of wash water is shown to have minimum effect on grade at 30 per cent solid concentration, and Fe upgrades obtained with and without wash water were found to be similar. Notable upgrades were observed at 35 and 40 per cent solid concentration with wash water. The results obtained suggest that the additional SiO2 rejection by wash water increases with an increase in solid concentration. This suggests that the benefit of using the drip system is notable at higher solid concentration. It is believed that at lower solid concentration SiO2 particles are reasonably free to move around and are possibly less entrapped than at high solid concentration.The Fe grade/recovery and solid concentration relationship with wash water showed a non-linear correlation. The Fe grade increases with an increase in solid concentration up to a somewhat optimum point and then drops as solid concentration increases further. The recovery of Fe on the other hand follows a converse relationship with solid concentration, the recovery decreases from 30 per cent to 35 per cent solid concentration and then increases again at 40 per cent solid concentration. The increase in recovery at higher solid concentration could possibly be explained by the fact that the mass yield to concentrate also increases with solid concentration. Since recovery is a function of both grade and mass yield, the higher recovery at 40 per cent solid concentration is likely due to the high mass yield obtainable at 40 per cent solid concentration.The drip system could therefore possibly offer a safe guarding against grade and solid concentration variations without using excessive water, and possibly ensure that a product within specification is maintained.CITATION:Ramotsabi, C M, Erasmus, W and Bornman, F, 2015. Optimisation of wash water on an iron ore spiral to improve grade, in Proceedings Iron Ore 2015, pp 175–184 (The Australasian Institute of Mining and Metallurgy: Me

Jul 13, 2015

Avoca Resources LimitedÆs Higginsville Gold Project has a resource base of over 1 300 000 oz of gold. The Trident underground mine, which forms the basis of the project development, has a resource base of 927 000 oz of gold. Avoca is building the Higginsville Gold Project based on a minimum ten year vision, producing over 150 000 oz per annum. The project development has taken less than three years from the Trident discovery hole in October 2004 to the first ore production in June 2007. This paper discusses the background work associated with the development of the Trident underground mine in a difficult period for new project development in Western Australia. The resources boom, led by the iron ore industry in the Western Australian Pilbara region, is creating cost pressures and, combined with a lack of people and equipment, is placing cost and timing stress on a small developing project. Avoca Resources has developed a project execution management strategy aimed at mitigating cost blow outs and schedule delays.

Jan 1, 2008

By E C. F Hamman

Sunrise Dam Gold Mine is a large open pit mine 730 km NE of Perth, Western Australia. Contract mining commenced in the open pit in September 1996 in lake clays and saprolites with the first fresh rock mined late 1999, and the underground starting the first decline in October 2003. By May 2007, over 150 million cubic metres of material had been mined and the pit was 360 m deep with 80 m remaining before reaching the planned final depth in early 2008. A final cut-back in the northwest will commence in late 2007 with open pit mining in the Mega Pit expected to conclude in late 2010. The challenges of developing the pit can be divided into three phases:Soft materials û mining was in multiple staged pits and cut-backs in lake clays, saprolites, weathered material. The varying characteristics had a significant impact on mining methods and slope stability. Structural û mining was gradually exposing more fresh rock and the drive was to understand how major structures and lithological contacts impact on local and large-scale stability. This had a significant influence on mine design and scheduling. Slope angles û achieving the final slope angle is critical. This is done through application of high standards of final wall establishment and proactive geotechnical hazard identification and management. This includes dealing with the rapid rate of descent, interaction with underground excavations and managing rock fall risk. The paper discusses each of these phases, highlighting the geotechnical controls implemented to date, looking at their success and impact on mining.

Jan 1, 2007

By A Dennis, T Hunter, R Coleman

For metallurgical plant design, it is necessary to progress through successive phases of test work, piloting and process development before involving all the other engineering disciplines and “freezing” the process design criteria and flow sheet. This process usually relies upon the experience, skills and personal preferences of various technology providers, study and engineering entities, test work and metallurgical laboratories and, most importantly, the owner’s team and its operators. Current industry trends include lower grades, more complex orebodies, geometallurgy in defining orebody variation and design envelopes, more common “hybrid” plant processes and the market demands for more reliable, timely and predictable early plant performance.This paper will discuss interaction of these trends and provide guidelines for the level of detail and technical complexity required for a number of different “typical” examples. The paper will pay particular attention to the study definition level translated into the required detail and certainty needed by the overall process “owner” and original equipment manufacturer (OEM) equipment suppliers to ensure the best real plant performance. Some recent case studies will be discussed. In many projects, at a late stage of project definition, it has become common practice to undertake a “value engineering” phase. Although it could be argued that this should be undertaken earlier, it is largely driven by an overall need to reduce capex and “optimise” the perceived “fat” built into the project during the detailed design process. This value engineering can be very counterproductive to project timing and operational performance and warrants discussion.The paper is intended to promote discussion on a topic of wide interest. The authors’ diverse backgrounds and experiences are integral to the views in this paper.CITATION:Dennis, A, Coleman, R and Hunter, T, 2017. Critical process design considerations from test work to operations, in Proceedings MetPlant 2017, pp 12–30 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By T Huynh, K Tungpalan, E Wightman, M Edraki, S Palaniandy

Most preventive environmental management practices promote proactive integrated approaches to waste management. For example, life cycle assessment is often used to find the ‘hot spots’ of environmental burdens. This kind of approach is often based on generic data and has rarely been used for tailings. Besides, life cycle assessments are less useful for designing operations or simulating changes in the process and consequent environmental outcomes. It is evident that an integrated approach for tailings research linked to better processing options is needed.The aim of this Nextmine™ project is to develop new tailings management models by streamlining orebody characterisation, process optimisation and rehabilitation. We present an integrated tailings management approach and preliminary results from a case study. Combined grinding and flotation models were developed using geometallurgical data from the orebody, to predict the properties of tailings produced under various processing conditions. The modelling scenarios based on the case study data provide the capacity to predict the composition of tailings and the resulting environmental management implications. For example, the type and content of clay minerals in tailings will affect the geotechnical stability and water recovery. Clay content will also influence decisions made for paste or thickened tailings and underground backfilling.CITATION:Edraki, M, Huynh, T, Wightman, E, Tungpalan, K and Palaniandy, S, 2015. An integrated approach to proactive tailings management, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 323–332 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By S N SHEARD

The use of geophysics in mineral exploration in Australia, and overseas, has increased dramatically over this century. This paper shows that using simple equipment with clever interpretation that the foundations of modem geophysics were laid, using all the same principles. The plethora and diversity of mineral exploration geophysical techniques does not allow a full description of their evolution to be given in such a paper. To convey this evolution, however, the progress of two different geophysical methods, magnetics - a potential field (passive) method, and electromagnetics - an electrical (active) method, are described. Examples of magnetic survey data from the 1920s and more recent vehicle home and airborne surveys are given to show the increase in data quality through technological improvement. A set of four airborne electromagnetic data sets spanning three decades is used to indicate the improvement in electromagnetic techniques. It is argued, that considerable progress is still required in the electromagnetic field to increase its interpretability.

Jan 1, 1992

By R Cox, S Pandey

The coal seam gas (CSG) industry is expanding rapidly in the Surat and Bowen basins. CSG production involves pumping water from the coal seams to release the gas adsorbed to coal particles. The reduction in water pressure in the coal seams will cause some reductions in water pressure in overlying and underlying aquifers because there will always be some interconnectivity between the formations. The Surat Basin is a sub-basin of the Great Artesian Basin, which contains aquifers of high economic, environmental and cultural value. The Condamine Alluvium is also an important water resource, which overlies parts of the eastern margin of the Surat Basin.Under the Queensland (Qld) regulatory framework, an area of intensive CSG development involving multiple CSG operators can be declared to be a cumulative management area. For such areas the Office of Groundwater Impact Assessment develops assessments of future impacts on aquifer water pressures and develops and manages arrangements. The results are published in underground water impact reports.The Surat underground water impact report (QWC, 2012) was approved in December 2012. This paper summarises the place of the report in the Queensland regulatory framework, the content of the report and progress in its implementation.CITATION:Cox, R and Pandey, S, 2013. Managing groundwater impacts in the Surat Basin, in Proceedings Water in Mining 2013 , pp 169-174 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

Level measurement of underground orepasses is important. Orepasses are not only utilised to funnel ore to the shaft skip loading station but also as silos for storing of ore in order to smooth out ore flow in a shaft system. Safety and operational efficiency are also improved as proper orepass level measurement could prevent overfilling of tipping areas. A study was therefore commenced to determine alternative technologies available as well as identifying practical installations across the Anglo American plc Group. From an instrumentation perspective an orepass system is an extremely difficult environment to take measurements in. Factors like dust, vapour, interference, bridging, wear and physical installation have to be taken into account. The study discusses time-of-flight (ultrasonics, radar and laser) measurement techniques followed by other possible solutions. These solutions included strain gauge measurement, the æjumping monkeyÆ technique, radiotomography, fibre optics and very long baseline interferometry (VLBI). Finally, various South African suppliers have been approached in order to determine instrumentation that is available for orepass level measurement in the marketplace. These recommendations were verified, where possible, by visiting the claimed installations.

Jan 1, 2005

By I C. Carrasco, V G. Mirada, J F. D Domingo, F S. Leite

This paper investigates ore loss and dilution produced by rock movement in bench blasting. A total of four blasts, in which electronic detonators have been used, were monitored in Cobre Las Cruces Open Pit Mine (FQM Ltd) in Gerena (Sevilla, Spain). Rock motion has been obtained in 137 points of the free face and 6 points inside the block. Multiple liner regression has been applied to predict rock motion and estimate ore dilution as a function of hole coordinates, rock contacts, powder factor/hole, amount of explosive per blasthole, burden, spacing, hole length, stemming length, explosive energy, hole row, subdrilling, blast sequence, stiffness ratio, blasthole distance to free face, rock density and Young’s modulus. The model is statistically significant with a determination coefficient over 0.8. Rock motion measurements in 31 more points have been used to validate the model and to show a reduction in ore dilution.CITATION:Domingo, J F D, Leite, F S, Mirada, V G and Carrasco, I C, 2015. Dilution, ore grade and blast movement calculation model, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 71–78 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015