Search Documents

By T. S. Spicer, C. C. Wright

A CHARACTERISTIC property of bituminous coal is that upon being heated the coal becomes plastic, evolves volatile gases, and finally solidifies into coke This fundamental characteristic is of utmost importance and is utilized in the production of the high-temperature coke upon which the steel industry is so dependent, but from the standpoint of operation in the domestic underfeed stoker this coking tendency seriously interferes with efficient combustion When the coke formed has too strong a structure, certain difficulties result, such as low rate of burning, slow response to heat demand, and, in extreme cases, extinction of fire The plastic mass prevents uniform distribution of air through the fuel bed and, With strongly coking coals, large dense pieces of coke are produced which have much less reacting surface thin was possessed by the original coal In both ignition and combustion of solid fuels, the extent of the reacting surface is an accelerating factor Poor combustion permits a surplus of fuel to accumulate in the furnace because the rate of feed and the rate of combustion are not in equilibrium, and this produces an unbalanced condition detrimental to continued) automatic service In order to burn strongly coking coals satisfactorily in a conventional stoker during the three requisite types of operation continuous, intermittent and hold-fire, frequent attention is necessary Domestic stokers are defined by the industry as residential stoker heaters that burn 60 lb of coal or less per hour With a few exceptions, these units employ the underfeed principle of combustion in which both air and coal move in the same direction up and through the fuel-bed Domestic combustion equipment has difficulty in meeting the problems presented by the several variations in ash and volatile matter, in ash-clinkering tendencies, in coking properties, and in the particle size of bituminous coals The work of Bituminous Coal Research Inc at Battelle Memorial Institute has shown that, of these, coking characteristics and the clinkering tendencies have the greatest effect upon the operation of the conventional clinkering type of stoker Typical coke formations in a clinkering type of underfeed domestic stoker are illustrated in Fig. I, which shows (A) the ideal fuel bed obtained with a noncoking or free-burning coal, (B) the type of fuel bed formed -with, a coal that produces a weal coke, and (C) the type of fuel bed obtained with a strongly coking coal C is characteristic of the fuel bed developed when the average Pennsylvania bituminous coal is ,burned in an underfeed stoker of conventional type It is apparent from these pictures that the formation of coke trees will seriously interfere with the efficient automatic combustion of Pennsylvania bituminous coals

Jan 1, 1942

By David Baker

A Discussion of the Paper of David Baker, read at the Lake Superior Meeting, September, 1904. (Washington Meeting, May, 1905.) MR. JOHN J. PORTER, Chicago Ill. (communication to the Secretary*) :-Mr. Baker's account of his experiences with stock-distribution has been particularly interesting to me, as it confirms the opinions which I had formed concerning the rapid failure of linings in several furnaces that have recently come to my notice. These furnaces, four -in number, are of modern construction, having been built or remodeled within the past two years, and are equipped with a well-known type of skip-hoist and double-bell charging-apparatus. In every case, a hot spot has developed within a few months after blowing-in, which has already compelled relining in two cases, and the probabilities are strongly against a long campaign in the other two. Since the hot spot in each case appeared in a position approximately opposite to the skip-hoist, and since the sizing, mentioned by Mr. Baker, is very apparent, it would seem as though there could be no doubt concerning the cause of the trouble. Nevertheless, there are some who cannot see it in that light; for the managers of two of these plants, at least, do not admit the existence of bad distribution, and have satisfied themselves by putting in cooling-plates, thickening the lining of the in-wall, and changing the brand of the fire-brick used for the construction of the walls. From observations of the clumping-action of the skip-hoist, and from subsequent inspection of the stock-distribution in the furnace itself, I arrived at the conclusion, some time ago, that no system of filling could be perfectly satisfactory where the stock is dumped into the hopper from one side, also that some

Mar 1, 1905

John J. Porter, Cincinnati, Ohio (communication to the Secretary *):—The remarks of Mr. Firmstone concerning the presence of nickel in Oriskany ores, call to my mind some additional evidence on this point. In 1903, while engaged in the determination of zinc in a number of samples of ore from the Oriskany mine of the Alleghany Ore & Iron Co., I was surprised to discover the presence of nickel and cobalt. As far as I was then able to discover, their present;! had up to this time remained unnoticed. The amounts ranged from 0.05 up to 0.10 per cent. of the combined oxides, and while no attempt was made to separate the metals, the presence of both nickel and cobalt was conclusively proven. Since that time I have learned that traces of these metals are of quite general occurrence in Virginia iron-ores, and more especially in the ores of the Potsdam formation from the western slopes of the Blue Ridge. In certain manganese-ores from this formation, I have found as high as 0.50 per cent. of nickel and cobalt oxides. Any one interested in this subject will find further information in a volume l written by Andrew 8. McCreath, and printed in 1884 for distribution by the Norfolk & Western railway. A number of complete and accurate analyses of Virginia iron-and manganese-ores are given, and practically all show nickel and cobalt in appreciable quantity. Still another source of information on the occurrence of nickel in iron-ores in the United States, for which I am indebted to Charles Catlett, is found in the Tenth Census. Several analyses of Oriskany ores are given: all of which show the presence of nickel, with less cobalt, while the single representative from the Potsdam formation shows nickel, with no cobalt.

Jan 1, 1909

TO THE BOARD OF DIRECTORS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS Gentlemen:-The following report covers briefly some of the more important activities of the Institute during the year 1923. In my report for the year 1922, I drew attention to the falling off in membership of the Institute due to the depressed condition of the mining industry in several lines and the inability of many of our members to find profitable employment in mining or its associated branches. A number who were unemployed during 1922 established connections during 1923, but a still greater number have been forced to resign or drop their membership during 1923. Fortunately, the number dropped is not so great as in the previous year. The Employment Service conducted by the four Founder Societies bears witness to the trend in business. For the young men just out of college, there are plenty of opportunities at small salaries, there are plenty of opportunities for them as laborers; but for the mature members, those of experience, there are few calls. During the last eighteen months, our Employment Service has been able to place only six of our members out of every hundred engineers for whom it has found work. Another loss which this Society has suffered, but which is not felt so keenly by our sister societies, is in its foreign members. The A. I. M. E. has always had a large foreign membership, but of recent years exchange has been so heavily against many European and South American countries that a large number of members residing abroad have been compelled to relinquish their membership. Almost invariably these members express keen regret because of the necessity that confronts them, and almost invariably the writers express hope that present conditions will not last long and that they will soon be able to ask-for reinstatement. Having stated the darkest side of the picture first, it may now be drawn to your attention that in spite of these losses the number of persons applying for membership was decidedly encouraging.

Jan 2, 1924

By H. J. Mutz

THE International Nickel Co. of Canada Ltd. operates five underground mines and an open pit. Four of the mines, the Frood-Stobie, Creighton, Murray, and Garson, are on the south range of the Sudbury Basin, map above, within a radius of 10 miles of the city of Sudbury, Ontario. The fifth mine, the Levack, is on the north range of the Sudbury Basin, 30 miles to the northwest of the city. The open pit is operating on surface ores of the Frood-Stobie orebody.

Jan 1, 1953

Jan 1, 1910

By Albert A. Mathews

OUTCROPS of gypsum rock near the present site of the city of Gland Rapids, Mich., were known to fur traders early in the nineteenth century. However, the deposits seemed without value and were not worked for some time. So far as cat1 be learned, Michigan gyp- sum was first used by a plasterer who settled in Grand Rapids in 1834 as a member of its fourteenth white family. In building a house for one of the early traders, be used some otnamental stucco mouldings manufactured from the local gypsum deposits for decorations in the gables and around some circular windows. The gypsum was broken out with a hammer, ground in an Indian corn mill, and burlled in a caulclron kettle,. After two attempts, the ornaments were successfully set, and remained on the house until it was destroyed by fire in 1850.

Jan 1, 1936

By Persifor Frazer

IT was my intention to have directed the attention of the members of the Institute to a complete series of rocks representing the older and middle formations represented in Pennsylvania, but time has been insufficient for the purpose, and I have been unable, in the first attempts to reduce the sections of those rocks, which I have brought with me to this meeting, to the requisite thinness necessary for exhibiting the peculiarities of their constituent minerals. The rocks represented here belong to the various horizons already mentioned, and include gneiss, ferruginous gneiss, chlorite slate, quartzites, and hydro-mica slates, limestones, dolomites, ferruginous conglomerates, quartz conglomerates, "Potomac marble" (nether member of the Mesozoic series), dolerites, and a syenite. The order in which these are named is, roughly, the order -of geographical position in a section line from southeast to northwest, commencing at the intersection of the Northern Central Railroad with the Maryland line, and ending a few miles from the town of York, and a short distance within the marginal outcrop of Mesozoic red sandstone. In such a geographical section all the rocks above mentioned would be encountered in the given order except syenite, about which a few words are to be said in a moment. (But this is far from representing the rocks in their geological sequence.) There is nothing of unusual interest to present to your notice in these slates and quartzites. The limestones were carefully searched under 450 diameters microscopic power, but they show no signs of organic remains. One section of a fine-grained Triassic sandstone contains a very beau¬tifully banded plate of quartz. But the objects of greatest interest at present are the specimens of trap. The more fine-grained and compact traps were collected from

Jan 1, 1875

A. 0. ASHMAN, Palmerton, Pa. (written discussion *.).-Mr. Newcomb's paper has interested me greatly, as I have had numerous experiences along this line. I do not think enough emphasis can be put on his warn-ing to keep platinum couples free from contact with quartz tubes, as silica shows a tendency to alloy with platinum to a surprising degree even at low temperatures. I have frequently had evidence of silica contamination in a perfectly good tube, in which there was seemingly no possibility of a reducing atmosphere. This is rather important as it seems to be common practice to insulate, as well as protect, the wires by means of- capillary silica tubing, thus allowing the entire wire to be in contact with the silica. The best way to mount a couple in a silica protecting tube is by means of double-bore porcelain insulating tubes, the protecting tube being slightly longer than the couple so as to leave a space between the couple and the end of the tube. In this way there is no possibility of contamination from silica. In no case should silica capillary tubes be used to insulate platinum wires. Mr. Newcomb states that there is still much to be desired in pyro-meter protecting tubes; this is in keeping with my experience. From a practical standpoint there is not a satisfactory pyrometer tube on the market for high temperatures; with all clue respect to the many improve-ments and good work recently done in this line. I believe that the whole future development of pyrometry is dependent on the development of suitable refractories. With suitable refractories, for example, Darling's1 work with liquid couples could be developed to a practical basis, making possible the use of base-metal couples to replace platinum.

Jan 12, 1919

By J. B. Umpleby

The subject of reservoir energy and its efficient utilization has been well explored in many papers. The present effort, therefore, is limited to a summary of existing information combined with an emphasis of the probability that the relative importance of controlling factors will change with advancing knowledge. Consequently the necessity for flexibility in laws and regulations, inherent in the problem, is emphasized. Definitions Many terms have been widely used in the literature without having been specifically defined. For example, confusion exists in the use of ((reservoir energy" and "gas energy." The latter is much more limited in meaning than the former. Other terms have been variously used. Consequently, I shall preface my remarks with definitions of a few of the more pertinent terms. Reservoir energy is that force or forces, active or potential, that is native to the reservoir and has the power to move oil through the reservoir rock. The energy may result from expanding gas, from hydrostatic head, from the weight of overburden, or from any other source. Gas energy is the expansive power of gas when pressure is reduced. It is one type of reservoir energy. An oil reservoir is that part of a geologic formation or formations in which oil occurs in commercial quantities wholly surrounded by nonproductive rock. The essence of this definition is effective separation rather than remoteness and under it oil reservoirs may be superimposed in the same oil pool. Conservation of reservoir energy means primarily its maximum use in the production of oil. Unit operation is a plan of development and production, which embraces an entire oil reservoir under a unity of engineering control. It is distinct from unitization, which has to do with arrangements of organization and equities to make unit operation possible in areas of divided ownership.

Jan 1, 1934

By Robert Hunt

The American Institute of Mining and Metallurgical Engineers was the first American technical organization to consider steel-rail specifications and sections. If I am not mistaken, the first contribution on those subjects to the Proceedings of the Institute was presented by Prof. Thomas Egleston, in 1874, and was entitled "Investigations on Iron and Steel Rails made in Europe in the Year 1873.1" The next contribution was Dr. C. B. Dudley's report of his investigation for the Pennsylvania Railroad of the wear of steel rails in their tracks, in 1878, which contribution led to a very memorable discussion that extended through several meetings.2 In 1880, Mr. C. P. Sandberg3 presented an article on rail specifications and inspection and rail sections. This was followed, in 1881, by A. L. Holley,4 in his exhaustive report on the then used American rail sections. The next contribution, I believe, was made by myself' at the Buffalo meeting, in 1888, on steel-rail specifications, which I followed,6 in 1889, by a paper on steel-rail sections. Since that time there have been numerous contributions to the Transactions of the Institute in relation to the manufacture of steel rails. The American Society of Civil Engineers officially took up the investigation of the relation of rail sections to the wear of car wheels in 1888. In the prosecution of this work, the Society appointed a special committee, whose labors extended through several years and resulted in an exhaustive report to the Society in 1893.7 Later, another committee was appointed to consider specifications for the manufacture of steel rails; the labors of this committee extended over a period of several years, a final report8 being made in 1910. It was my fortune to be the secretary of both of those committees.

Jan 9, 1919

By R. J. Wysor

MORE than two years ago, in making efficiency tests on our hot-blast stoves, I was surprised to discover a marked difference in temperature as indicated by a pyrometer inserted near a stove on blast, and the regular recording instrument situated near the bustle pipe. A special hole was then provided at the junction of the hot-blast main and the bustle pipe, and portable pyrometers with bare fire ends were used, both at this point and in the stove necks. I had occasion to make a number of such tests on various stoves on the same furnace, the difference in temperature as shown by the two pyrometers varying chiefly with the temperature of the blast, and the distance of the stove from the furnace. However, this difference was always great, often averaging above 100° F., for the entire period of a stove on blast. Later, experiments were made with similar results on another group of stoves. The pyrometers used were properly standardized and checked against each other before and after each test. However, there was still a slight doubt as to the accuracy of the results obtained, as subsequently explained. But I have obtained corroboration of the magnitude of heat losses from blast-furnace hot-blast mains from two independent sources. I have learned from H. A. Brassert, Superintendent of Blast Furnaces, South Works, Illinois Steel Co., that he has recently clone some experimental work similar to my own, and found temperature drops of the same order of magnitude. Also, C. R.. Lyle, of the Armstrong Cork Co., has made some interesting theoretical calculations, based oil the thermal conductivity of fire brick, for the particular conditions of several of our tests; and his theoretical interpolations, all facts being considered, check our actual observations fairly well. I understand that Mr. Lyle expects to publish the results of his investigations.

Jan 10, 1915

By Charles Shamel

I FEAR most of the Institute members are already weary of the perennial controversy about the apex law. I feel that way about it myself now, though I have been guilty of considerable contribution to the discussion in the past. The discussion does not seem to perceptibly influence previously held views and I would not again break into print on the subject but for the urgent invitation of the Chairman of our, Law Committee. This energetic and able member has firmly determined to secure a revision of the mining law and among other things to eliminate the so-called apex provision from the U. S. mining statutes. He is, however, fair about it and has invited me to make "the strongest possible argument in its favor." I am suspicious that he is acting on the psychological principle that it is usually easier to convince an audience against a cause vigorously but unsuccessfully defended than against one wholly mute. Nevertheless, I realize that personally he wishes me no harm, much as he hates the apex law, and so am willing that the Institute have whatever benefit may accrue from my taking up again the unpopular side of the discussion. I say this because the attitude of a large part of our "articulate" membership seems irreconcilably hostile; their minds are made up; favorable consideration is foreclosed; and they become impatient and even sarcastic at any attempt to elucidate a favorable view of the apex law. The exact question for discussion at the present time is not whether on abstract, or any other considerations, the apex law is the best possible rule, but the very different proposition whether, after nearly 50 years of statutory life and much longer as a practically universal miners' custom, it is now just and expedient to repeal the apex law.

Jan 4, 1914

By Stephen Taber

JOHN C. BRANNER, Stanford University, Cal. (communication to the Secretary *).-Wideawake teachers of geology are constantly on the lookout for good illustrations of veins, especially where the processes of formation are either clearly shown or suggested. And I long ago found out that one who would learn nature's laws must despise nothing. It thus happened that in 1910, Dr. George J. Peirce of the depart-ment of botany at Stanford University called to my attention a cracked and broken yellow earthenware dish, 8 ½ in. across the top and 2 ½ in. deep, that, to the ordinary observer, seemed to be of no further use, and quite ready for the waste can. The striking thing about this dish was that the thin glaze over much of the outside surface and over the upper margin of the inside surface had been lifted in small scales, varying in. diameter from ½ cm. to 1 cm., and thrust outward and held there by some sort of white fibrous mineral. The process looked very much like one we are familiar with in the Southern States where. we often see in the winter pebbles and soil thrust out from a clay bank or lifted from a clay soil and held there supported by what is popularly known as needle-ice. Upon inquiry I learned the following facts in regard to the history of this particular dish: In the summer of 1910, it had been partly filled with a concentrated salt solution taken from one of the salterns of the Stauffer Chemical Co. at Redwood City, Cal. A qualitative analysis of the original brine showed: Present: iron, magnesium, sodium, potassium, chlorides, sulphates, nitrates (trace), bromides, carbonates, borates (trace), and considerable amounts of organic matter. Absent: calcium, lithium and iodides.

Jan 3, 1917

By Sherwin F. Kelly

THE geophysical scene shifts and alters, the emphasis changes, and new possibilities loom, but the tendency is always towards widening the field and deepening the analytical penetration. Seismic methods have had their heyday, the torsion balance is being displaced by the gravimeter, electrical methods are showing deeper penetration, soil analysis is the newest tool, and gamma-ray logging appears on the horizon. One of the striking features of re- cent geophysical work in the oil fields has been the marked decrease in the number of seismic crews employed. Although the percentage of company crews is believed to have increased appreciably. the sum total has fallen sharply, as shown by the figures for the Gulf Coast area. About two years ago probably over 100 seismic parties were operating there, whereas now there are only about 35. This decrease may be partly due to the low prices of petroleum with a consequent reluctance to spend money to increase crude-oil re- serves but more probably to the fact that reflection and refraction shooting have been carried on so extensively that they have been applied to a large pro- portion of the areas in which they may reasonably be expected to succeed. Some of the earlier enthusiasm, particularly over reflection prospecting, may have erred on the side of over- optimism; some of the present curtailment may be due to over pessimism; but in the opinion of various observers seismic work at the present rate seems to be at it- optimum. It nevertheless remains pre-eminent as a technique for detailing structures in areas where good reflections can be obtained and is the only method that will give accurate depth to definite beds. Results may be poor in certain areas but many regions still remain wherein it can be applied, so that plenty of structural mapping remains to be done by the reflection seismic method.

Jan 1, 1940

By Felix A. Vogel

I (New York Meeting, February, 1912.) FLUE-DUST, to most blast-furnace operators, means a troublesome by-product, the formation of which should be curtailed, if not prevented entirely. However, with the increasing use of fine ores, larger furnaces, and high-pressure blast, the production of flue-dust is constantly increasing, and amounts annually in the United States to from 3,000,000 to 3,500,000 tons, An exceedingly high tonnage, of which a large part has been discarded as valueless. As a result of greater economy in the iron industry, the attention of our furnace-men has been directed towards the utilization of this enormous amount of waste material, a problem which had also been given due consideration by metallurgists abroad. Flue-dust is generally a fine material containing considerable coke and iron-ore, with a small admixture of lime and silica, depending upon the burden. The iron-ore is partly reduced, which shows that the dust originates largely in the reducing-zone of the blast-furnace. In the United States this dust usually contains 20 per cent. of coke and more than 40 per cent. of iron. Estimating coke to be worth $3.25 per ton, and iron-ore 7 cents per unit, a ton of flue-dust, unless made available, represents a loss to the furnace-man of $3.50. This accounts for the first efforts to recharge the flue-dust into the furnace, either by moistening it clown with an excess of water, or mixing it with clay to form balls of pulp, or treating it with lime-water. These methods, however, have been practically discarded, as they failed to produce the desired economies. To recover, in the blast-furnace, all the values represented by the material contained in the flue-dust, the following con¬ditions should be complied with

May 1, 1912

By Luther Wagoner

Having given in a former paper1 the results of assays of sea-water, bay-mud, dredgings from San Francisco bay, etc., and believing it might be interesting to extend the work to include some deep-sea dredgings, I procured from the Smithsonian Institution six samples taken by the U. S. steamer Albatross, and marked as follows: Depth in No. station. Locality. Latitude. Longitude. Fathoms. 1. 2103. Off Delaware bay. 38' 47' 20" N., 72o 37' W., 1,091. 2. 2265 to Between Chesapeake 35° 37' N., 74O to 75O W., 49 to 70. 2297. bay and Hatteras. 3. 2420. Off Chesapeake bay. 37' 03' 20" N., 74O 31' 40" W., 104. 4. 2528. East of Georges 41° 47' N., 65o 37' 30" W., 677. bank. 5. 2572. SE. of Georges bank. 40° 29' N., 66O 041 W., 1,769. 6. 2681 South of Nantucket. 39' 43' N., 70' 29' W., 990. The above samples were assayed by the cyanide-method, described in my former paper (p. 807), about 30 g. of sample being used, and the following results were obtained: Value in Milligrams Per Metric Ton. No. Station. Gold. Silver. 1. 2103. 145 1,014 2. 2265 to 2297. 44 304 3. 2420. 15 353 4. 2628. 267 1,963 5. 2572. 125 377 6. 2681. 66 414 No. 4, Station 2528, consisting of red clay and volcanic ash, mas re-assayed ; 35 g. was roasted at a low heat for one hour and weighed 34.05 g. after roasting; the color was changed to a deep brick-red; and when assayed by the cyanide-method

Jan 1, 1908

By A. H. Tousley

Current problems in the cement industry are discussed and suggestions for solving them by modernization are made. Cement facility modernization is discussed in considerable detail with examples illustrating before and after conditions. Itemized are the improvements realized in better working conditions, better efficiency, higher production, lower costs, and better community relations. These improvements are related to the overall profitability of the particular plant or facility.

Jan 1, 1972

William Metcalf, Pittsburg, Pa. (communication to the Secretary*): I am greatly pleased that some one has at last reached what I have long regarded as the only rational explanation yet given of the reasons why steel hardens. Mr. Field claims originality; and doubtless he is entitled to it, but not to priority, mhich must be granted to Prof. John W. Langley.' The difference between them is that Langley says " Tension, probably molecular," and Field says " Tension, probably atomic "; in either case the vital thing after solution is tension. Mr. Field's argument carries with it the idea of increase of density with hardness; if he mill study the facts farther he will observe that the case is just the reverse; that is, the greater the hardness the less the specific gravity; it was just this fact that led Langley to his conclusion, in mhich I have always concurred. Field agrees with Langley that the first requisite for perfect hardening is complete solution of the carbon, not combination; and all of the facts agree with this conclusion. The fact that increase of hardness causes reduction of density was first brought to my notice some 40 years ago, when Major William Wade was testing Jones & Laughlin's cold-rolled iron, and I mas his assistant. We found the well-known increase of tenacity, compressive strength, torsional resistance, and hardness. Specific-gravity tests showed that the cold-rolled iron was less dense than the hot-rolled bars. Major Wade was so surprised at this result that he gave me a lot of samples to weigh, saying that he was not satisfied with

Jan 1, 1904

By S. C. Lindsay, D. J. I. Evans

With each year that passes hydrometallurgical processes are being more widely used to recover base metals from ores and concentrates. Generally these processes involve liquid-solid separation of metal-bearing liquors from barren residues. This may be done by countercurrent decantation, thickening and filtration, or filtration or centrifuging only. Choice of method is governed by chemical and physical characteristics of the pulps; cost of labor, power, materials, and waste disposal; and even by the amount of capital available when building plans are under way. Since all these controlling factors change with time and location and with technological advances, the separation method must be re-evaluated when new plants or expansion programs are contemplated. At the Sherritt Gordon refinery in Fort Saskatchewan, Alberta, an ammonia pressure leaching process recovers nickel, copper, and cobalt from the nickel concentrate produced at Lynn Lake, Manitoba.' Pregnant liquors are separated from the barren leach residues in a thickener-filter liquid-solids circuit. The decision to use this type of separation was based on a summation of economic factors during the pilot plant and design stages. Although countercurrent decantation was not incorporated in the refinery flowsheet, the problems solved in thickening the leach residues and the experience gained in operating the commercial plant are pertinent to countercurrent decantation, particularly where it is applied to slow-settling leach slurries or slurries having a relatively high vapor pressure of a valuable, obnoxious, or poisonous vapor. The nickel sulfide concentrate is leached under pressure with air and ammonia to dissolve the nickel, copper, and cobalt and most of the sulfur, leaving a residue of iron and siliceous material to be discarded.2,3 During a subsequent distillation stage to recirculate part of the ammonia used for leaching, copper is recovered from the solution as a high-grade sulfide. After further purification to remove traces of copper and undesirable sulfur compounds, the nickel is precipitated by hydrogen under pressure at an elevated temperature. The cobalt, together with unreduced nickel, is precipitated as a mixed metal sulfide by hydrogen sulfide for eventual cobalt recovery. The end solution is then evaporated to produce a crystalline ammonium sulfate byproduct. As shown in Fig. 1, the nickel concentrate is leached in a continuous, two-stage, countercurrent circuit. In the first stage, or adjustment leach, the fresh concentrate is partially leached (60 pct) in the liquor produced in the second stage, or final leach. This system is necessary to produce a solution suitable for treatment in the copper sulfide precipitation step. Both stages are carried out at 170" to 180°F under a total pressure, with air, of 100 to 120 psig in large, horizontal, water-cooled autoclaves. The autoclaves are divided by overflow weirs into four compartments to give a certain amount of staging during leaching. In each compartment a relatively slow-speed (100 to 150 rpm) agitator maintains the nickel concentrate in suspension. Adjustment leaching, carried out in two autoclaves in parallel, is followed by a thickener-filter liquid-solids separation. Final leaching is done in two parallel trains of three autoclaves using aqueous ammonia to extract metal values from the adjustment leach residues. This too is followed by a thickener-filter circuit. Here the residues are repulped once with aqueous ammonia and twice with process water and refiltered after each repulping stage, to insure a maximum recovery of soluble metal, before being discarded to the tailings pond. The adjustment leach is followed by a seven-disk Dorr-Oliver American filter, with an agitator in the filter boot to keep the residues in suspension. Agitators have also been installed beneath the four ten-disk filters following the final leach thickener. Slurry Characteristics: A typical analysis of the Lynn Lake nickel concentrate, produced by differential flotation,' is given in Table I. The concentrate comprises 35 to 49 pct pentlandite, (Fe, Ni)S; 3 to 6 pct chalcopyrite, CuFeS,; 1 to 4 pct pyrite, FeS2; and 24 to 42 pct pyrrhotite, Fe1-2S (where x varies between 0 and 0.2) together with various siliceous minerals such as actinolite, hornblende, and talc. During leaching, the sulfur in the pentlandite, chalcopyrite, and part of the pyrrhotite is successively oxidized through the thiosulfate and poly-thionate radicals to sulfate and sulfamate." Simultaneously the nickel, copper, and cobalt are converted to soluble ammine complexes and the iron in the pentlandite, chalcopyrite, and part of the pyrrhotite is oxidized to a spongy hydrated iron oxide. The hydrated iron oxide is readily broken down by the agitation needed to sustain the concentrate in suspension and to maintain a satisfactory mass transfer of the oxygen from the air to the slurry. Table I shows typical chemical, screen, and

Jan 1, 1961