Search Documents

By J. A. Brierley, Roshan B. Bhappu, D. H. Reynolds, P. H. Johnson

Although the economic importance of recovering copper by leaching of mine work dumps from open-pit operations has been realized for some time, serious attempts to understand and to improve such operations through scientifi research has been made only in recent years. This progress report covers the results of chemical, physical, and biological studies pertaining to the dump-leaching process and discusses salient features and parameters that may be helpful in improving such operations. The dump leaching of low-grade copper ores, as an integral part of the open-pit mining operations in the Southwest, has been practiced for the last 50 years and is increasing in importance as one of the major sources of copper. The recent acceleration in dump leaching can be attributed to: (1) the greater tonnages of low-grade ores mined and dumped at newer mines as well as resulting from increased stripping ratios at the older mines, (2) the relatively small investment required for dump leaching facilities per pound of copper recovered contrasted with expansion of milling facilities to recover equal amounts of the metal by raising tonnage throughout, (3) low labor requirements needed for leaching, and (4) the simple and continuous nature of the process needing little close supervision of trained operators. In the past, the mining companies have not worried about efficiency in dump leaching but have been satisfied with whatever metal recoveries could be made without much effort. However, because of the huge amounts of metal accumulating in the low-grade waste dumps, compared to the relatively small amount recovered annually, an operator today cannot leave dump leaching to chance. What appears to be a simple, empirical process is actually a very complex one involving a large number of critical factors that encompass Several Scientific disciplines, such as physics, chemistry, geology, biology, and hydrology. It is imperative that

Jan 1, 1970

By M. H. Forester, John D. Cooner

ALTHOUGH the unmined anthracite will last for approximately A 150 years, most of the thicker and cleaner coal beds have been almost entirely first-mined and pretty well robbed, leaving much of the present and future production to come from thin and dirtier beds. Herewith is a section of one of the dirty beds being mined in the Wyoming region This section shows that 45.8 per cent of the bed is made up of impurities and that the 45 in. of coal in the bed is in five benches, the thickest of which is 19 inches. In some localities of the anthracite region there are 14 beds of minable coal. Orderly and proper mining of the coal makes it necessary to rob or second-mine-almost all beds have already been first-mined-in sequence from the top downward. Therefore the robbing of the few remaining portions of the thicker and cleaner beds is in many instances being held up by the mining of the overlying thin and dirtier coal beds. Impurities Impurities consist of fire clay, slate, rock, and bone. The latter, which is black, contains 40 to 60 per cent carbon and often resembles good coal. In some beds there are also bands of "blue" coal, which, as the name implies, is of a bluish slaty color. Although much of this "blue" coal has a carban content almost as high as the good anthracite, it is not

Jan 1, 1943

By Thirumalai, K.

Although the term "spalling" has long been known, Norton l first referred to its usage for the fracture or disintegration of materials subjected to rapid temperature changes. Spalling of ceramic materials at high temperatures has received attention in the past. Removal of the char formed during ablation in re-entry of space vehicles has been referred to as mechanical spalling. The first experiments to evaluate the process of rock fragmentation by thermal spalling were conducted by Stoces using a series of gasoline burners on the quartz veins of the Zinnwald deep mines in Germany. After the development of rocket-jet burners, the principles of 'thermal spalling combined with high fluid momentum found wide practical application in rocks. The well-known jet piercing process for drilling blastholes in taconite and for jet channeling in the quarrying of granite are among the more notable of these application^.

Jan 1, 1970

By R. F. Stilwell

There are three things that all coal consumers look for when they burn coal: (1) suitability for their particular requirements and burning equipment, (2) uniformity of shipments, and (3) quality as expressed by heating value and other chemical and physical tests. Suitability, or proper application, is determined generally from previous buying experience. It is a function of (1) the reliability and integrity of the shipper and distributor, (2) of a certain coal field or seam and of (3) uniformity and quality. Quality is limited by the location and geology of the seam and mine, the mining and preparation methods and equipment and the knowledge and ability of the personnel. Uniformity of shipments is in many ways the most important factor in coal selection. Lack of uniformity in chemical quality, size consist and treatment cause most of the customer complaints that arise from faults of the coal shipper. Lack of uniformity destroys suitability and quality standards, causing a large customer turnover, and greatly increases sales expense and reduces the net return to the operator. Oil and gas fuels are more uniform in quality than solid fuels, and there will be more gas and oil competition for coal markets after this war than before, because the size of their market is a direct function of the dimensions of their pipe lines, which have been greatly increased during the war. Present mechanical coal-cleaning equipment based upon gravity concentration has gone a long way toward giving us a coal of uniform ash content. The chart in Fig. I, by Hebley,1 shows the greater uniformity of the ash content of washed coal as compared with that of raw coal. Wide variation in the nature and amount of ash in the coal feed to the washer leads to a coal of non-uniform ash content. Mechanica1 cleaning equipment does not understand such terms as ash-softening temperature, coking properties, size consist and sulphur content. Unless the feed to the washer is uniform, the washed coal probably will not be uniform. Table I shows the ash, sulphur and ash-softening temperature of two mines in the Pittsburgh bed, both raw and washed, loaded over the same tipple; also No. 3 and No. 4 Pocahontas seams, both raw and washed, loaded from the same preparation plant. It is obvious that they must be blended or loaded separately if a uniform product is to be obtained. Why Is Blending Necessary? It was natural for the operators of captive mines producing by-product coals to recognize the necessity for blending raw coals of different quality and coking characteristics. They have had many years of experience with blending high, low and medium volatile coals at their oven plants. They have found that careful blending gives a coke of more uniform quality and better structure. Coals that could not be

Jan 1, 1947

By R. F. Stilwell

There are three things that all coal consumers look for when they burn coal: (1) suitability for their particular requirements and burning equipment, (2) uniformity of shipments, and (3) quality as expressed by heating value and other chemical and physical tests. Suitability, or proper application, is determined generally from previous buying experience. It is a function of (1) the reliability and integrity of the shipper and distributor, (2) of a certain coal field or seam and of (3) uniformity and quality. Quality is limited by the location and geology of the seam and mine, the mining and preparation methods and equipment and the knowledge and ability of the personnel. Uniformity of shipments is in many ways the most important factor in coal selection. Lack of uniformity in chemical quality, size consist and treatment cause most of the customer complaints that arise from faults of the coal shipper. Lack of uniformity destroys suitability and quality standards, causing a large customer turnover, and greatly increases sales expense and reduces the net return to the operator. Oil and gas fuels are more uniform in quality than solid fuels, and there will be more gas and oil competition for coal markets after this war than before, because the size of their market is a direct function of the dimensions of their pipe lines, which have been greatly increased during the war. Present mechanical coal-cleaning equipment based upon gravity concentration has gone a long way toward giving us a coal of uniform ash content. The chart in Fig. I, by Hebley,1 shows the greater uniformity of the ash content of washed coal as compared with that of raw coal. Wide variation in the nature and amount of ash in the coal feed to the washer leads to a coal of non-uniform ash content. Mechanica1 cleaning equipment does not understand such terms as ash-softening temperature, coking properties, size consist and sulphur content. Unless the feed to the washer is uniform, the washed coal probably will not be uniform. Table I shows the ash, sulphur and ash-softening temperature of two mines in the Pittsburgh bed, both raw and washed, loaded over the same tipple; also No. 3 and No. 4 Pocahontas seams, both raw and washed, loaded from the same preparation plant. It is obvious that they must be blended or loaded separately if a uniform product is to be obtained. Why Is Blending Necessary? It was natural for the operators of captive mines producing by-product coals to recognize the necessity for blending raw coals of different quality and coking characteristics. They have had many years of experience with blending high, low and medium volatile coals at their oven plants. They have found that careful blending gives a coke of more uniform quality and better structure. Coals that could not be

Jan 1, 1947

By Henry F. Adams, Guy H. Ruggles

IN this paper the authors aim to chronicle the experience and salient points brought out in changing flotation reagents at a concentrator which had probably been using a mininium amount of oil at a minimum cost per ton, to a more complicated system requiring a partial chemical control. The original oils were coal tar and pine oil. The new reagents are lime, xanthate and pine oil. It was found that there were no insurmountable difficulties and eventually the cost of the new reagents per ton of ore proved to be very little more than that of the old. LIME PLANT When the question of handling lime came up there were two propositions open: (1) to handle the lime dry; (2) to handle it wet in the form of an emulsion. Granting that a dry lime feeder would function properly, delivering lime uniformly, the chief objection was the dust that would be raised when these feeders were being charged or operated, as the only possible location was on a gallery beneath which men were working. With this objection the handling of lime as an emulsion seemed to be the better scheme. The lime plant which was first installed was for experimental work on one section. This was gradually changed and developed until it was of sufficient size to accommodate 20 sections. The various changes will not be discussed and the following description deals only with the fully developed plant. Crude as it is, and perhaps somewhat expensive to operate, the lime-handling plant has been quite successful. Much has been learned which will pave the way for a better installation in the future. Burnt lime is received loose in standard gage box cars. This is the product of the kilns and has had no screening or sorting. A grab sample is taken from each car as it is unloaded. An average of the analyses of samples from 44 cars gave the following: [ ]

Jan 1, 1928

By Lucius W. Mayer

The iron-mines of the Ilsede Hütte Co. are at a town called Peine, about 20 miles east of the city of Hanover, on the railroad to Brunswick (Braunschweig). Hanover, the capital of the province, is a military city, of approximately 250,000 inhabitants, and Brunswick, 33 miles to the westward, has half this number. The mines here described are located in a hamlet called Bülten. The Ilsede Hütte Co. operates two mines, 1.5 miles apart, in this district, Gruber Bülten Adenstadt and Gruber Lengede Bodenstadt. It also operates an iron-mine north of Hanover, known as Eiserhaven, and one in the Harz mountains, the Georg Friedrich, at Grauhof. At Bülten a coarse conglomerate, a, Figs. 1 and 2, contains nodules of limonite, cemented together by calcium phosphate. The ore contains Fe, 25 to 45; Mn, 3 to 4; P, 0.6 to 1.4; S, 0.02 to 0.09; and CaCO3, 40 per cent. Directly above the conglomerate is limestone, b, followed by a mixture of clay and sand, c. Below the conglomerate is a hard clay floor, d. The ore-body, from 10 to, 12 km. long, and from 3 to 4 km. wide, has a maximum thickness of 20 m. It clips approximately 10° S.E., and strikes N. 45° E. Diamond-drill prospecting shows that the thickness diminishes to 1 m. as the end of the deposit is approached to the northward. At this point the deposit is 250 m. below the surface. In Fig. 2, the arrow, A, indicates the general direction of the work along the face, a, which is carried forward in a straight line for its entire length. At B, a train is approaching, which has come from the bench-track, shown at G, by a circuitous route, and is dumping the overburden behind the face, in the space left by the excavated rock. Formerly the work at this mine was essentially open-cut, the deposit having a very strong outcrop. Figs. 1 and 2 show also

Sep 1, 1908

By Å. Sterten, R. Tunold, J. Brun, K. Dalatun

c axis compression behavior of beryllium single crystals at three purity levels under hydrostatic pressures up to 27 kbars was determined. Extensive non-basal slip, observed by two-surface trace analysis and transmission electron microscopy, occurred under a hydrostatic pressure of about 12 kbars (175 ksi) for the high-purity (twelve-zone pass) material and at about 19 kbar (275 ksi) for the lower-purity (zone-leveled) material. Prismatic loops with a (c + a) Burgers vector were observed in association with second-phase parti- A principal factor limiting the use of beryllium is its brittle behavior when tested at the usual strain rates (E = 10-4 sec- 1) at temperatures below about 200°C and under impact conditions at temperatures in excess of 200°C. It has been proposed' that the brittle-ness of beryllium is associated with the lack of a sufficient number of independent slip modes and the absence of a slip mode with a Burgers vector out of the basal plane [presumably (c + a) pyramidal slip mode] and to the ease with which beryllium cleaves on the basal and second-order prism planes. The absence of pyramidal slip has been attributed to a high Peierls-Nabarro stress associated with the motion of dislocations with a (c + a) vector and the ease with which cleavage occurs on the basal and second-order prism planes. The experimental evidence in support of the proposed explanation for the brittleness of beryllium is far from complete; for example, that the ductile-to-brittle transition in polycrystalline beryllium is associated with the operation of profuse (C + a) slip has not been unequivocally established. The occurrence of (c + a) slip ({1122}(1123)) has been experimentally established2-5 under conditions where basal and prism cleavage are restricted in a c axis compression test. In these investigations (C +a) slip was found in high-purity beryllium single crystals tested in c axis compression* at 200°C and in Be-4.4 pct Cu and Be-5.2 pct cles in the lower-purity materials tested. The loops were related to surface "extrusions" observed on many of these same specimens. Nonbasal dislocations operating on (1122) planes with a (c + a) Burgers vector were observed. The presence of c and a dislocations together with (c + a) dislocations suggests that the (c + a) dislocations dissociate presumably on unloading or after failure of the test crystals to c and a dislocations. terial, (c + a) slip has only been observed near the the fracture4 surface in room-temperature c axis compression tests. Fracture in these tests occurs without measurable plastic flow, as determined with a strain sensitivity of 10"6. Since it has been shown for many metals that the application of hydrostatic pressure suppresses fracture,?-' it was felt that studying the behavior of unalloyed beryllium single crystals stressed in c axis compression under a hydrostatic pressure would reveal whether (c + a) can occur if fracture was prevented, and that it might elucidate the role of (c + a) slip in the ductile to brittle transition. Evidence that (C + a) slip is associated with increased ductility in a high-pressure environment has been found in stress-strain tests on poly crystalline beryllium.10 The present paper describes a study on the influence of a hydrostatic pressure environment on the occurrence of (c + a) slip in beryllium single crystals. Material of two purity levels was tested in c axis compression over the pressure range ambient to about 27.5 kbars.* 1) MATERIAL PREPARATION AND CHARACTERIZATION Two lots of low-purity single-crystal beryllium were used. The first lot was "ingot secondary refined grade" and designated lot A. The second lot (lot B) was produced by a two floating zone pass zone-leveling operation in an argon-filled sealed quartz apparatus on a 1-in.-diam by 12-in.-long bar of Pechiney secondary refined-grade vacuum-cast and hot-extruded material. The high-purity material (lot C) was made by traversing twelve floating zone passes through a similar bar of Pechiney secondary refined-grade vacuum-cast and hot-extruded material. In a series of spark cutting and lapping procedures,11 single-. crystal specimens some 0.12 in. sq by 0.30 in. high were made with the sides Parallel to the first- and second-order prism planes and the basal plane within 3' of arc of the top and bottom surfaces of the specimen. Such an accurate orientation is necessary because of the large difference in resolved shear stress

Jan 1, 1970

By A. Eilers

In a former paper on Western Smelting Works, I mentioned the great difficulty of obtaining accurate information in regard to the economy of the processes in practice; and to-day, although nearly two years have elapsed since my former paper was written, I am sorry to say that very little improvement has taken place in the keeping of accounts, and in the direction of a more systematic management in the majority of these works. But I am quite certain that by this time even the most sanguine furnace managers must have become convinced, from the experience of the last year, that somewhere in their processes there are enormous losses. Rates for the purchase of ores in 1873 were not as high as they were in former years in certain parts of the country ; labor was no 'higher than formerly; the demand for unparted lead was good throughout the year, with the only exception of the time of the panic, in the fall of 1873; yet there are, of between 40 and 50 works, not more than two or three in Utah and Nevada to-day, that have paid a reasonable interest on the capital invested.

By A. Filers

IN a former paper on Western Smelting Works, I mentioned the great difficulty of obtaining accurate information in regard to the economy of the processes in practice ; and to-day, although nearly two years have elapsed since my former paper was written, I am sorry to say that very little improvement has taken place in the keeping of accounts, and in the direction of a more systematic management in the majority of these works. But I am quite certain that by this time even the most sanguine furnace managers must have become convinced, from the experience of the last year, that somewhere in their processes there are enormous losses. Rates for the purchase of ores in 1873 were not as high as they were in former years in certain parts of the country ; labor was no higher than formerly ; the demand for unparted lead was good throughout the year, with the only exception of the time of the panic, in the fall of 1873; yet there are, of between 40 and 50 works, not more than two or three in Utah and Nevada to-day, that have paid a reasonable interest on the capital invested.

Jan 1, 1875

By Willard S. Morse

In my paper on "The Lixiviation of Silver-Ores by the Russell Process at Aspen, Colorado" (page 137 of the present volume), attention was called to the decrease in "chlorination " during the washing of the roasted ore with water, to remove soluble salts, before leaching with hyposulphite and Russell solutions. This decrease in " chlorination," which is due to conversion of the silver chloride to some other form not soluble in hyposulphite solutions, and which, for the sake of brevity, will be termed the "going-back" of chlorination, has been a serious obstacle to the successful operation of several leaching-works, and was at Aspen the only difficulty encountered. I have never seen any explanation of the cause of this failure to extract, in actual practice in the mill, the amount of silver chloride shown by laboratory-leachings to be present in the roasted ore; and the purpose of this paper is to record the conclusions arrived at concerning the cause of the phenomenon, and the data upon which they are based. The average decrease in chlorination by washing with water in the Aspen ores for a period of fourteen months was as follows:

Jan 1, 1896

By Henry M. Bates, Roscoe Pound

Mr. Chairman and Gentlemen: I accepted your Chairman's invitation to speak to a group of experts in this field with the greatest hesitation, because I know little or nothing about it. Certainly I can make no detailed suggestions, or suggest planning along very definite lines. You cannot do that sort of thing in a vacuum, and as I have suggested, my knowledge of the whole oil problem is next to nothing. It is possible that as a student of our public law, constitutional law particularly, for a number of years, I have acquired a perspective that may enable me to offer, for what they are worth, some general thoughts on these problems. I think that nothing in the whole field of law requires more definitely and clearly the functional approach than does the problem of a sound legal solution of the difficulties of the oil and gas industry. The industry is dealing with substances that are peculiar, and one must know how those substances act and what has been the history of the industry, to undertake to make anything like specific suggestions. I certainly am not qualified.

Jan 1, 1935

By O. M. McRae. Discussion by R. W. Jones

R. W. Jones (Senior Exploration Geologist, Standard Oil Co. of California, Box 250, Seattle, Wash.) -Mr. McRae6 and his colleagues are to be congratulated for providing a more coherent structural synthesis of the complex structure in the Courtland-Gleeson area, Cochise County, Arizona, than the "gigantic thrust breccia" concept of Gilluly. 4 However, a few problems of interpretation remain. It is the intent of this note to point out some of these problems, and, drawing on my own work in the area as well as the work of McRae6 and Gilluly, 4 to suggest some interpretations which differ from those previously published. GRAVITY SLIDES In an unpublished manuscript (Jones5) I previously argued that most of the complex structures in the Courtland-Gleeson area can be most reasonably interpreted in terms of gravity sliding caused by uplift and eastward tilting of Jurassic intrusives and associated Paleozoic rocks. Although the field work and drill hole data described by McRae6 provided excellent documentation for two important gravity slides, McRae6 interpreted the basic structure in the Courtland-Gleeson area in terms of major eastward directed thrusting. I continue to disbelieve the

Jan 1, 1967

By John V. Beall

Hard as the Revett quartzite are conditions governing the deep mines of the Coeur d'Al6ne. In fourscore years of mining, heat and pressure have been the rewards of preseverance. Such obstacles are the natural concommitant to search for ore at depth. But high cost and shortage of miners is a creeping frustration of the decade. These grim observations were made on a trip to the mines of the Coeur d'Al6ne in the first week of May. But the bouncy optimism of competent mining engineers and geologists overrides by far the tough conditions. This is the story of what they are doing. I think they are setting the stage for the wonder mines of tomorrow. I didn't meet all the people or see all the mines, so there are unfortunate gaps in the story. Then too, sometimes the muck and water blotched my notes, or I couldn't write fast enough or I was too tired. No matter. There is much to tell and, because it is basically a human story, I am flouting the rules of technical journalism and couching it in the neglected "I" person. First then, a little history . . . .

Jan 7, 1966

.MAX ROESLER, Firmeza, Oriente, Cuba (communication to the Secretary?).-It is substantially admitted by all who have recently been in touch with these deposits that the orebodies lie in the fine-grained dark-green rocks, called diorite by most writers and diabasic by myself. The three points of disagreement concern the agency of included limestone blocks as causes of deposition, the agency of the

Jan 5, 1917

By W. B. Boggs, J. N. Anderson

An account of the operation of the Noranda smelter covering the period from December, 1927, when the smelter started, until December, 1929, was given in a paper published by the Canadian Institute of Mining and Metallurgy early in 1930.' The object of the present paper is to review matters of interest in the original paper and to describe the present construction and operation of the smelter, with particular reference to the reverberatory-furnace practice. The Noranda smelter was built by Noranda Mines, Ltd., from the designs of A. E. Wheeler, consulting metallurgist of New York, for the reduction of ores and concentrates from the Horne mine and to treat, on a custom basis, ores and concentrates from other mines in the Rouyn district. The smelter is at Noranda, about 330 miles directly north of Toronto. Construction work was started in June, 1926, and copper was first produced in December, 1927. The smelter was built throughout as two duplicate units, each with a rated capacity of 500 tons of ore per day. Operations were started with one unit and after several months it was found that one unit alone could smelt 1000 tons of ore a day. At that time there was only one hoisting shaft, No. 3, and its hoisting capacity and the capacity of the original crushing plant were insufficient to supply ore for the two units at the increased tonnage. Accordingly No. 4 shaft was sunk and a new crushing plant provided to handle the ore hoisted there. Operating two units at capacity also required the installation of two more converters to treat the additional quantity of matte produced. This work was completed in the latter part of November, 1929, and since then both smelter units have been operating continuously. In 1928, a mill to treat 500 tons a day of concentrating ore was completed. Since then the concentrator capacity has been increased twice, and at present 2000 tons a day of ore are being concentrated. The layout of the surface plant of the mine, concentrator and smelter is shown in Fig. 1 and the general plan in Fig. 2. The smelter is shown in more detail in Fig. 3. The original hoisting shaft, No. 3, is now used only for handling men, supplies and waste rock, and the original crushing

Jan 1, 1934

C. N. FEnner, New York City (communication to the Secretary) : A possible explanation of some of the' phenomena of amalgamation cited by Mr. Bayliss and others has occurred to me. We know that if, to a quantity of mercury, gold and silver are added until a putty-like paste is formed, and if this mass is spread on a flat surface and pressure is applied, a more fluid portion of the mercury will be squeezed out from the rest, carrying gold and silver with it. The proportion of gold to silver will depend, I think, upon various causes and conditions—the relative chemical affinity which gold and silver have for mercury; the amount of pressure used; the presence of other metals:

Jan 1, 1898

By Alden Greninger

THE time-honored description of the growth of metal crystals to form polycrystalline aggregates is one in which two important steps are con-sidered: (1) nucleation, and (2) dendritic growth, each dendrite starting from its individual nucleus and resulting (upon slow cooling, assuming no solid phase changes) in a macrograin. This picture of the process of crystallization is incomplete, and it is with the hope of enlarging upon it that the following summary and correlation of experimental results are given. MOSAIC STRUCTURE For an exact definition of the mosaic structure of metal crystals-if, indeed, one can be found that will hold for all metals-one must await the results of much experimental work in this field. The writer's investiga-tions have been confined almost entirely to copper and a few of its alloys. The following terms are proposed, and will be used in this report: Macromosaic Structure l.-Large-scale mosaic structure; more specif-ically, mosaic structure of a scale large enough to produce splitting of Laue spots on back-reflection Laue X-ray patterns2. The deviation from exact parallelism of neighboring macromosaics varies from a few

Jan 1, 1935

By C. P. PERIN, DONALD BELCHER

T HE production of pure iron by electrolyzing solutions of its salts has been the object of scientific curiosity and research for about 80 years; and in the last two decades a realization of the unusual physical and chemical qualities of electrolytic iron has turned the attention of chemists and metallurgists toward a commercial application of this accumulated knowledge. Thus Burgess and Hambuechen in America, . Cowper-Coles in England, and Fischer in Germany- devised methods, more or less successful, for the electrolytic refining of iron, but none of these processes has yet attained large-scale operation. During the war some interesting ,work was done in France and England on building up worn or defective machine parts by electrodeposition of iron. It remained for the Société "Le Fern in France to carry on the process commercially. For six years Les Fonderies et Forges. de Sainte-Maire et Gravigny and the works of Bouchayer & Viallet at Grenoble have manufactured pure-iron boiler tubes in competition with established practice. The French process originated in the researches of Anthelme Boucher in 1910, and was, not put into operation until several years of experimentation had passed.

Jan 1, 1921

By C. A. HEILANDG

THERE is a need for men well trained in geo- physical prospecting. Although the number of geophysicists required by the industry in the future cannot be expected to be very great, there will always be a demand for courses on the subject. A number of educational institutions are, therefore, interested in providing instruction in geophysical prospecting. Some institutions will be satisfied with courses in general geophysical prospecting designed to give the geologist fundamental concepts on the comparative merits of the methods and the interpretation of the results. Other institutions will want to give special instructions in theory, field procedure, and interpretation of any or all geophysical methods. In giving such special courses a number of problems will be faced, and it seems to me that such difficulties are easier to overcome in an engineering institution than in a university. A knowledge of basic engineering subjects, such as required of all students in an engineering school, seems to be the best foundation upon

Jan 1, 1930