Search Documents

By Hans Lundberg

AFTER the war years, great activity has been shown in geophysical exploration for ore. The appreciation by mining and government geologists of geophysical techniques and results is largely responsible for the popularity of these methods. In Canada, plans are being made to study, by geophysical methods, the structure of a portion of the Pre-Cambrian shield in the hope that such studies will not only give a clearer picture of the geology, but will be of direct aid to the mining companies when selecting areas for detailed prospecting. Although geophysics thus has become more popular, some engineers are still reluctant to employ the methods to their full extent. Allotted funds are often rather low, so that the least expensive

Jan 1, 1947

By C. D. Keen

In the latter part of the summer of 1913 the Conservation Commission of the State of Louisiana, under presidency of M: L. Alexander, decided to stop the waste of natural gas going on at the "burning gas-well," Located about 2 mile southeast of Oil City, La. On several occasions, both in newspapers and in reports, comment had been made on the condition of this well, its harmful effect on the Caddo gas field, and the considerable loss, estimated at several thousand dollars each month, caused by the escape of the valuable fuel., But nothing had been done to bring the well under control and prevent further waste of gas until the State Conservation Commission took the matter in hand. The gas fields of Louisiana are among the greatest in the country. So far most of the gas has been found in the Caddo field proper, although considerable development has been done in and around the city of Shreveport and near the town of Mansfield in DeSoto parish. To extend the life of the gas fields and to prevent the quick exhaustion of the supply of the natural fuel are matters of vital importance for this section of the country. Four gas companies have entered the Caddo field and supply the surrounding towns and cities With gas. The Arkansas Natural Gas Co. has pipe lines to Little Rock, Ark., and supplies gas to the following cities and towns in that State: Texarkana, Hope, Garland, Emmet, Prescott, Boughton, Beirne, Gurdon, Arkadelphia, Gum Springs, Mal-vern, Dsnaldson, Gifford, Perla, Beaton, Beauxite, Mabelvale, Bryant, Sheridan, Pine Bluff, Little Rock, Argenta, Pulaski Heights, and Hot Springs. The Southwestern Gas & Electric Co. transports gas to Mooringsport, Blanchard, Caddo, Rodessa, Oil City, Vivian, Bloomburg, Hosston, Ida, Dixie, Belcher, and Shreveport. The Marshall Gas Co. supplies gas to the town of Marshall, Texas. The Louisiana Co. has a line to Shreveport. In, the oil field the gas is used for drilling purposes, and the operators either have their own gas system or buy from the gas companies. At the present time the surrounding territory depends for its fuel supply on the Caddo field, and the importance of the conservation of the natural-gas

Jan 1, 1915

By J. M. Callow

THe results obtained by pneumatic flotation throughout the country on all classes of ore, and the tonnage now being treated by this particular method, speak for themselves. Its advantages over the so-called agitation process are now established by facts and data from practicc. The comparative efficiency of a rapidly revolving paddle, as a means for aerating an ore pulp, and of a cyeloidal or turbine blower for the same purpose, would seem to be so obvious as to leave no room for discussion. Practitioners in this art are to be congratulated on the acquisition of the valuable literary contributions that have recently been made on the theory of flotation by Messrs. Ralston, Van Arsdale, Taggart and Beach, and others, and the very valuable and able articles by Messrs. Laist and Wiggin on "Flotation Concentration at Anaconda, Mont.," by Dr. Rudolf Gahl on the "History of Flotation at Inspiration," and by David Cole on "The Advent of Flotation in the Morenci District." It is not within the province of this article to attempt an answer to the various issues raised in regard to the theory, or to defend the one advanced by me a year ago. But since discussion usually benefits the profession, a reply will be made to some of the statements made by the last-named writers. CoMPABATIVE SENSITIVENESS AND ATTENDANCE Concerning the article, "Flotation Concentration at Anaconda, Mont.," by Laist and Wiggin, a little explanation is in order. It should be stated that, with the exception of about 24 days at the end of the testing period, the Callow experimental plant at Anaconda was not run under my direction. This perhaps accounts for some of the concIusions drawn on page 499 of the descriptive paper. The conclusion that the use of acid seems to be of considerable advantage, calls for some comment. While the tests conducted by the Anaconda Copper Co. do show acid to be of considerable benefit, this is a consequence of using acid sludge as a flotation agent. My belief has always been that the Anaconda

Jan 1, 1917

By RICHARD MAIZE

IN this critical period of our history, the coal industry of the nation, faced with many obstacles, performed its work safely during the first ten months of 1943. Thousands of the younger mine workers were inducted into the armed forces of our country and in many instances their jobs have been filled by others without much if any experience and training. This situation alone would seem to be sufficient to interfere with the safe and orderly operation of the industry but the Government's demand for a substantial increase in coal tonnage over that produced in normal times introduced a hazard which always accompanies speed, regardless of the skill of the worker.

Jan 1, 1944

By R. S. Dean

REQUIREMENTS for war materials have led to large scale experimentation upon metallurgical innovations. It is of interest to inquire what this may contribute of permanent value to our existing technology, as innovations adopted during war are apt to be discarded promptly at its end. This is because utilization of substandard ores usually requires a new technology for ore treatment, and a new use-pattern for employment of the products. Thus two very different problems are involved: first, devising a process; then, adopting its products by industry, with readjustments of the use-pattern if necessary. A new process may be as good or better than an old one, but the readjustments required for use of its products may prevent its general adoption if this implies scrapping existing plants and investing much additional capital. Metallurgical innovations are of three kinds: I. The use of substandard material in processes already established; 2. The grading-up of substandard material to render it more suitable for established processes; 3. The adjustment of technology and use-pattern to the raw materials that we have.

Jan 1, 1945

By M. Baeyertz

SINCE 1915 many papers and books have covered industrial applications of X-rays from various angles. Two of the more recent are a paper by Fink and Archer1, which describes in detail the technique of radiography, and a paper by Clark2, which embraces the whole field of X-ray metallography. This paper, therefore, is confined to work of the X-ray Laboratory of the Western Electric Co., which naturally divides into two categories: radiography and diffraction patterns of various types.

Jan 1, 1930

By W. E. Remmers

The defect in wire known as "cuppiness" has appeared and disappeared from time to time but the exact cause of its appearance or disappearance has not heretofore been known definitely. This defect is not limited to one particular metal or alloy but seems to be found at various times in all of the materials that are drawn into wire. Fig. 1 represents cuppy wire made from an aluminum alloy and Fig. 2 illustrates copper wire that became cuppy in drawing without intermediate annealing. Differences of opinion are current among the manufacturers of wire and in the literature (see bibliography at end of paper), some believing that the source of the trouble lies in segregation in the wire rod, oxides, sulfides, slag, etc.; others that the trouble is created by an unevenness of stress distribution across the section of the wire, usually thought of as being a function of die shape. All of the published work is of a qualitative rather than a quantitative nature. With this in mind, it was deemed advisable to make a study of the shape of the wire-drawing dies, as well as the oxygen content of the copper to be drawn. Experimental After several methods were tried, it was found that by studying the contour of the butt-end of the rod after drawing a measure of the "working" across the section of the wire could be made. The butt-end of the annealed rod was not sheared but was sawed off. The end was then smoothed with a fine file so that the plane of filing was perpendicular to the drawing axis. It is to be noted that this method is not an absolute measure of the distribution of cold working but is a very good indicative means of studying comparative values. The method of examining a tension break in wire was found to be the most sensitive in detecting cuppiness. Other methods, such as microscopic examination of longitudinal sections, X-ray radiographic studies, etching away of outer layers with nitric acid, and fracture by bending, can all be used to identify cuppy wire but the tension break will give the fracture characteristic of cuppiness before any of the other methods can

Jan 1, 1930

By Robert Lewis

THE Utah coal field to which the name Book Cliffs is applied runs in a northeast direction from Mt. Hilgarde, in Sevier county, along the escarpment of the Wasatch Plateau to the vicinity of Castle Gate, thence southeast along the Book cliffs, which lie to the north of and generally within sight of the Denver & Rio Grande Railroad,. to the Colorado line. The Book cliffs form the southern escarpment of the West and East Travaputs Plateaus, and vary in height from 2,000 to 6,000 ft. At the base of the Wasatch and Book Cliffs escarpments is a broad plain known as Castle valley. The coal beds outcropping in the escarpments along this valley are worked on the largest scale of any in the State, and this particular area is known locally as the Castle Valley coal field. Geology The Book cliffs are capped by the Tertiary-Eocene-formation, consisting of varicolored shales; buff sandstone, conglomerate, and subordinate thin beds of limestone. Different sections show diverse stratigraphy. This is mainly the Wasatch formation, and lies unconformably upon the rocks of the Upper Cretaceous. Fig. 1 is a generalized section of the rocks of the. Book Cliffs field. The Mesaverde formation contains the cliff-making rocks of the Book cliffs, and is composed of massive sandstone interbedded with sandy shales and beds of coal and carbonaceous shale. The sandstone has greater resistance to erosion and the formation is characterized by escarpment ledges and cliffs. The shale is commonly sandy and is drab in color, but where it is associated with the coal it is usually carbonaceous. The sandstone is generally buff, though occasionally it is white, and in places red. The bedding ranges from thin to massive. In the lower part. of the formation the sandstone is red in

Jan 7, 1914

Jan 1, 1969

By H. E. Exner

This article is a critical review of the influence of surface preparation on crack formation at Vickers indentations in the test used by Palmqvist3-7 to evaluate the toughness of cemented carbides. Experimental results are presented which clearly show that grinding introduces compressive surface stresses into the cobalt phase and thus reduces the crack length. The deformed surface layer is removed by polishing and a stress pattern is approached corresponding to that in the bulk material. Cracks of maximum length are characteristic of this stress state. Deformation stresses can be removed by annealing above 800°C. On the basis of these results , sample preparation for the crack length test can be simplified, the accuracy of measurement is improved, and a simple and significani parameter is found to describe crack resistance of cemented carbides. FOLLOWING suggestions by Ammann and Hinniiber,1'2 Palmqvist3-7 developed a method for testing the toughness of cemented carbides using as a measure the sum of crack lengths at the four corners of a Vickers hardness indentation. This method has several advantages over the bend test commonly used in carbide technology: a) specially formed samples are unnecessary; b) sufficient information can be obtained from one sample; c) the scatter is relatively small; d) the range of actual values for commercial cutting alloys is wide. Thus, this test is both cheaper and more precise than the bend test. Nevertheless, Palmqvist's method is not widely used, mainly for two reasons: a) The relationship between crack length and the technological properties of the material (wear and shock resistance) is not clear. b) The crack length is strongly dependent on surface treatment. It is necessary, therefore, that surface preparation be very precise and reproducible, conditions usually hard to obtain. While any other simple mechanical test has this first drawback, the second became crucial in the application of the crack length method as a practical test. The reasons that this drawback could not be eliminated are, in our opinion, misleading and inconsistent interpretations of the influence of surface preparation on the crack length given in literature. In the following, after a short review of previous experimental results the interpretations given by different authors,4?'-11 cf. Table I, are discussed critically and a consistent explanation is presented on the basis of which improvements of the method of crack length testing are proposed. 1) PREVIOUS EXPERIMENTAL RESULTS In his first attempt to use the cracks at Vickers impressions as a quantitative measure of the toughness of cemented carbides, palmqvist3 calculated the work necessary to initiate cracks by the formula: Sk =k.Pk. [I] where k = numerical constant = 6.49, Sk = critical work to initiate cracks (gf cm), Pk = critical load (load necessary to initiate cracks) HV = Vickers hardness (kp per sq mm). The difficulties involved in experimental determination of the critical load were overcome by the observation that a linear relation holds between the applied load and the sum of the crack lengths at the four corners of the indentation. This linear function, given by Eq. [2] below, was confirmed by Dawihl and Alt-meyer9and by our experiments, see Fig. 1: I = a1.P +a2 [2] where 1 = sum of the crack lengths at a Vickers indentation, P = applied load, al, a2 = parameters dependent on the toughness of the alloy and the surface preparation. The critical load, Pk, is now given by a2, which can be obtained by extrapolating the load vs crack length line to zero crack length, see Fig. 1. This simple relationship, Eq. [2], led Palmqvist1,7 to a parameter which was more reproducible and easier to obtain experimentally than the critical work: the work, S300, put into the sample to produce an average crack length of 300 µm per indentation. This parameter is calculated using the formula: where the load, P3oo, giving a crack length of 300 µm, can be taken from the load-crack length plot, Fig. 1,

Jan 1, 1970

By R. F. Mehl

Jan 1, 1936

By G. O. Hiers

THE object of the experiments reported in this paper is to determine the eutectic composition of copper and tin and to determine the location of the part of the liquidus line immediately above the eutectic composition in copper. Three methods were used in the investigation: (1) the method of dissolving copper in a bath of molten tin at constant temperature, with the idea that when the bath was saturated with copper its copper content, by analysis, together with the temperature at which the saturation took place would locate a point on the liquidus line (2) the method of the differential cooling curves, and (3) the method of microscopic examination. This paper is principally concerned with the results of the last two methods mentioned. The results of the first method, that of dissolving copper in molten tin, did not agree with the .results of Miller,1 by the same method, nor with the results of other investigators by other methods, nor yet with the results of the cooling-¬curve experiments and microscopic examination reported here.

Jan 1, 1929

By Henry M. Howe

The present paper aims to present in brief the results of Tetskichi Mukai's* studies of the remarkable changes in the properties of manganese-steel caused by changes in the rate of cooling, together with some inferences of my own. Manganese-steel may vary greatly in composition ; that containing from 10 to 13 per cent. of manganese has hitherto reached the widest use. In this paper I consider manganese-steel of about this composition only. To distinguish common steel from manganese-steel, I speak of the

Jan 1, 1893

By John Hall

(New York Meeting, October, 1913.) THE Fremont test for measuring the energy consumed in breaking a notched bar of steel is not so well known in this country as it deserves to be. The test specimen used in this test is about 3/8 by 1/4 by about 11/4 in., notched with a hack saw on the lower side to cause the piece to break at a fixed point. A weight of 10 kg. falling 4 m., and provided with a knife or. chisel which strikes the specimen, breaks the test piece by impact. The residual force in the falling weight after it has broken the specimen is recorded by a suitable device, and the difference between the total energy and the residual energy of the weight (in kilogrammeters) is the force consumed in breaking the specimen. An experience of several years with the Fremont testing machine has shown its great value in readily detecting brittleness not revealed by tensile testing or slow bending testing. In this paper it is proposed to discuss (1) the supersensitiveness of the test as applied to cast steel and (2) its value in revealing the effect of heat treatment under certain conditions.

Jan 7, 1913

By Francis C. Krauskopf, Carl E. Swartz

Metallurgists differ considerably in their opinions regarding the effect, if any, of small amounts of iron pyrites, or other iron compounds on zinc sulfide ores during the roasting operation. As a result, the literature on this subject expresses many conflicting ideas. The ore, previously crushed to pass through a 1-mm. screen, dries in the roasting kiln, losing water up to 200° to 300° C. At 150° C. iron pyrites begin to lose sulfur. As the temperature increases, while the ore is passing to the hotter part of the furnace, the sulfur burns to sulfur dioxide, leaving the metals as zinc oxide and ferric oxide. These two substances then interact to form zinc ferrite, a compound, yellow brown in color, having the general characteristics of a spinel. Like magnetite, another spinel, zinc ferrite is insoluble in alkalis and dilute acids. As a result, when leached with 10 per cent. sulfuric acid solution, zinc values tied up in this compound remain behind History In the electrolytic recovery of zinc from its ores, the roasted ores are usually leached with a 10 per cent. sulfuric acid solution. When the zinc ore contains iron pyrites as an impurity in an appreciable amount, the actual yield of metallic zinc is much lower than a theoretical calculation would indicate. Further, losses of zinc are, in a rough way, directly proportional to the amount of iron pyrites or other iron compounds present. When the iron is present in the ore in an isomorphous relation to the zinc, as in the case of a marmatite, a greater amount of zinc remains insoluble than when present as a true pyrite or marcasite. Work on the insoluble residues obtained from leaching of the calcines shows that the zinc lost is intimately tied up in this residue. Some investigators have suggested a definite compound, such as zinc ferrite; others merely a mixture of zinc and iron compounds. As early as 1851, Pelouze(')' prepared calcium ferrite by fusion of calcium oxide and ferric oxide. Ebelman, 2) about the same time, prepared

Jan 1, 1928

By Hugh O?Neill

IN PREVIOUS papers,1 the author has reported the results of experiments on the straining in tension of a single crystal test piece, about 0.6 in. long, of vacuum-melted electrolytic iron containing 1.8 per cent. of silicon. The crystal was originally in the "as cast" condition, and was stressed slowly along a tetragonal axis so that slipping along conjugate gliding planes finally transformed the original cylindrical portion into a pair of fracture wedges. One of these fracture wedges was sectioned along the stress axis in a plane at right angles to the edge of the wedge. A metallographic study of this plane of -section led to the conclusion that slip had taken place in the (111) direction along (112) planes making a V shape with the stress axis. The present paper describes the results of scratch-hardness tests conducted on the same section, in order to determine the distribution of strain hardness therein, followed by annealing, and considers the resulting variations in hardness. These observations supplement those made by Krivobok2 on similar material reduced 25 per cent. by hammering (i. e., by impact) in the cold. In order to investigate ageing effects, two small crystals of the same alloy were also tested.

Jan 1, 1928

By M. A. Schimmelpfennig, A. D. S. Gillies

Loss of visibility due to the occurrence of atmospheric fogging in underground mine airways can lead to longer travel times and loss of production efficiency, an increase in the frequency of vehicular and foot traffic accidents and difficulty in checking rock surfaces for instability and loose material. Where hot and humid surface air meets colder underground air, conditions for fog formation may be present. Further, suspended particulate matter from diesel exhausts or stoping operations together with slow movement of air along passageways may contribute to formation. This study describes an investigation being undertaken with the cooperation of Kennecott's Ozark Lead Co. to identify causes of the problem.

Jan 1, 1984

By J. D. Pennock

The different samples of brick examined were Grecian magnesite, American magnesite; silica brick and coke-oven tiling made in Belgium and used in retort coke-ovens. The Grecian magnesite was furnished by a New Pork party. The American magnesite and the silica brick were furnished by a manufacturing company in Pittsburgh. From these brick were made cylindrical cores, '79 inches long and 15/8 inches in diameter. At one end of each was drilled a hole about 1/4-inch in diameter and 11/4 inches long, into which the thermometer was inserted during the experiment. Conductivity.—The apparatus used for determining the conductivity, as shown in Fig. 1, is a sheetriron drum, 18 inches in diameter and 8 inches high. In the center is a little combustion-chamber with walls of split fire-brick, 39 inches square and about 6 inches high. The fire-brick, however, pass through the drum to the table on which the drum stands. The cores are placed horizontally, half-way between the top and bottom of drum and on the line of diameters at right angles. In the four walls of the combustion-chamber are cut holes just large enough to allow the cores to pass through. The cores extend

Jan 1, 1897

By Strathmore R. B. Cooke

That calcium will activate quartz for flotation with anionic collectors such as soaps has been known for a number of years,1 2 3 and the method has been applied to the concentration of various iron ore 4 5 6 as well as to other materials. Clemmer gives the permissible pH range for the activation of quartz by calcium as between 9.5 and 12.5 with an optimum value of 11.0, and Hertzog7 has determined the calcium abstraction of iron ores and of Ottawa sand, but otherwise little quantitative data are available. The purpose of the present investigation was to determine those conditions under which dilute solutions of calcium chloride will activate quartz for anionic flotation and to determine the amount of calcium ion adsorbed by quartz. Those variables, the influence of which was primary, such as calcium, sodium, and hydrogen ion concentrations, were studied. Other factors which influenced the results are discussed in the description of the experiments. Three different experimental methods were used to determine the activation of the quartz. The first method was to treat a sample of ground, deslimed quartz with solutions of calcium chloride and sodium hydroxide, and to determine the calcium adsorbed by chemical analysis of the solution. Ad- vantages are that a direct value for the

Jan 1, 1949

A. L. BLOMFIELD, ? Colorado Springs, Colo. (written discussion?).¬I congratulate the author on bringing out a paper of real service to the profession. His contention of uniform size in balls is borne out by my own experience; in coarse crushing at the Golden Cycle in 6 by 6-ft. (1.8 by 1.8-m.) ball-mills we unquestionably gain by screening out the small balls once or twice a month. The point of gaging the ball size to be used by the uniformity of screen sizing is of particular interest. The necessity of sufficient return feed from classifier to the ball-mill is sound and clearly shown. In connection with this, I wish two further points had been gone into as thoroughly: (1) The effect of the quality of classification. In general, it is true that the smaller the per cent. of undersize in the feed the more effective is the mill's work. This is true on a bucking board, in tube-mills, ball-mills, and grinding pans. Given the possibility of returning. a full-feed load to any mill, it has been my experience that the effective work in the grinder is almost proportional to the quality of the return feed. (2) Again speaking generally, the shorter the tube-mill the greater is the quantity of return feed necessary to keep it loaded. The classification thus keeps the oversize in the mill more free from finished product and thus the crushing more efficient. It is very easy to overload any long mill with too much return

Jan 4, 1919