Search Documents

By John H. Hearding

Induction heating, together with automatically controlled tempering and hardening is giving Oliver faster and more accurate bit sharpening, while experiments with bit taper promise to offer increased footage per bit.

Jan 10, 1953

By M. B. Holt

At this time, when electricity in its various applications is attract- ing so much interest, and with such good reason, it has been suggested to me that, as the Aspen Mining and Smelting Company, of Aspen, Pitkin county, Colorado, was the first mining company in America to employ electrical power for hoisting, a record of what has been accomplished by this company would be of interest. Early in the year 1888 the question of power for the development of the ore-horizon lying below the level of the tunnel through which the property is worked, became one of importance. The conditions under which it was proposed to use power were as follows (See Fig. 1): The company's mines lie upon the northwestern slope of a mountain, the ascent of which is at an angle of 28' from the horizon. The ore, consisting of argentiferous galena and other silver-bearing mineral, is found at or near the plane of contact of a superincumbent mass of blue limestone, with an underlying bed of dolomite. This contact plane dips north 30° west, at an angle of 60' with the horizon. A tunnel 1000 feet in length, driven south into the mountain near

Jan 1, 1892

By R. L. Templin, D. A. Paul

The modulus of elasticity is defined as the ratio of stress within the proportional limit to corresponding strain. This property, as thus defined, is a constant for each kind of material; and in tension or compression is usually designated by the symbol E. The modulus of elasticity serves as an index of the stiffness of a material or a measure of its ability to resist change of shape under stresses not higher than the proportional limit. In view of the frequency with which the modulus of elasticity is used in engineering calculations, it is surprising to note the uncertainty that exists as to authentic values, and the marked lack of published information relating to the variation of the constant E within individual alloy systems. A value of 10,000,000 Ib. per sq. in. has been quoted as representative of aluminum and its alloys. This value has been found to be approximately corrcct for pure aluminum and aluminum alloys in which the total percentage of the alloying elements is low, but seriously in error in the case of alloys that contain relatively large amounts of the alloying elements. a National Metals Handbook. b Intcrnatiunal Critical Tables. '' Aluminum Co. of America. " Based on density of alurminum (2.70). c Smithsonian Pliysical Tables.

Jan 1, 1931

By H. S. Cannon, F. N. Rhines

IT. H. Hausner( Sylvunia Electric Products Inc., Bay-side, N. Y.)—The results reported by the authors are interesting because they contribute some information on the principles of sintering and also because of a certain practical value for the manufacture of powder . metallurgical parts in production. Pressed powder compacts are frequently sintered in a boat in several layers so that the lower layers are actually sintered under the weight of the upper layers and, therefore, are frequently deformed. The authors gave information on this deformation process by determining the effect of the load on the density. The experimental setup of the authors, however, has a disadvantage—that the sintering occurred in a cylindrical container so that the deformation was stopped in the direction of the diameter. The authors should have rather called this a study of hot-pressing than of sintering. I want to call the attention of the authors and others interested in sintering under load to the experimental work described by Dawihl and Rix.' These authors sintered cylindrical compacts under a lengthwise ten-sional load of 0 to 25 g and found that the shrinkage in length and diameter changes considerably with the load, but that the volume shrinkage is affected very little by the load. H. S. Cannon (authors' reply)—We wish to thank Dr. Hausner for calling attention to the experimental work of Dawihl and Rix. The fact that they found volume shrinkage little affected by varying tensional loads during sintering seems to support the contention that the forces due to loading are equivalent to and additive to the forces which cause densification. This contention is the basis of our comparison of sintering and creep.

Jan 1, 1952

By Earl R. Hoskins, James E. Russell

The electrical resistivity of rocks has been studied quite extensively, in particular, the effects of temperature and confining pressure on resistivity. References 1 through 6 at the end of this chapter pertain to electrical resistivity of rock and contain further references on the same topic. The present study is motivated by an interest in determining the in-situ properties of rock as well as the stress state of the rock and how these quantities are changing with time. Most of the previous work on the electrical resistivity of rocks has been directed toward saturated rocks at relatively high confining pressures and temperatures. The present study was oriented towards air-dry surface rock that might occur in mine pillars. The mean stress and temperature under such conditions are comparatively low. It has been demonstrated that the resistivity of rock is highly dependent upon the porosity. In fact, for saturated rocks, a relationship referred to as Archie's law has been established between porosity and electrical resistivity. In the case of saturated rock, the property that is actually being measured is the resistivity of the solid/fluid system. Since the resistivity of the fluid alone is usually much lower than that of the dry rock, it is understandable that the resistivity of a saturated rock is in general several orders of magnitude lower than the resistivity of a relatively dry rocli. For dry rock, it seems reasonable that the electrical resistivity should increase as microcracks open within the material. Since microcracks open as material is stressed closer and closer to its failure point, it appears that there should be a correlation between electrical resistivity

Jan 1, 1970

By Francis F. Lucas

A microscope objective of given numerical aperture, when used with light of given wave length, has some fixed limit of resolution. This may be expressed as potential resolving ability—the ability to resolve is inherent in the lens but whether this limit is achieved in practice is quite another matter. Nearly 50 years ago Abbe evolved theoretical considerations which indicated that the ability of a lens to resolve detail is directly proportional to twice the numerical aperture of the objective and inversely proportional to the wave length of the light used. It is true, unquestionably, that as the numerical aperture of the objective is increased the potential resolving ability of the lens is increased and likewise when the wave length of the light used is decreased, the degree of resolution is increased. Whether Abbe's formula expresses the exact relationship is not a matter of great concern. It suffices to know that to improve resolution, other things being equal, two avenues of approach are available. Either the numerical aperture of the objective may be increased or the wave length of the light decreased. With the apochromatic system it is possible to employ successfully wave lengths from 400 to 500 uu and still secure reasonably short exposures. The present limit for numerical aperture is 1.40 N. A. although objectives of 1.60 N. A. are now an experimental possibility for metallurgical work. Thus certain well defined limits are set for those who work within the range of the visible spectrum. In order to take advantage of the increase in resolving power which accompanies a decrease in the wave length of light employed, Dr. A. Kohler and Dr. M. Von Rohr of the Zeiss Scientific Staff developed the "monochromats." These are quartz objectives corrected for the single wave length 275 uu which lies in the ultra-violet region of the spectrum. They also developed a series of quartz oculars and a complete photo-micrographic equipment with which to use the quartz optics. Quartz must be used for the optical parts because glass absorbs ultra-violet light almost completely. Thus there was made available about 20 years

Jan 1, 1926

By J. H. Hollomon, L. D. Jaffe

The hardenability concept has become widely used during the last few years for the choice and substitution of steels. Before the work of Grossmann,1 the systems for predicting hardenability from chemical composition could be used only over a narrow range of composition. Grossmann introduced a comprehensive system, which has been effective in calculating the hardenability of most types of moderate or low-alloy steels. However, occasions often arise that require the calculation of the hardenability of high-alloy steels from their chemical compositions. Experimental determinations of the hardenabilities of such steels indicate that the Grossmann system predicts much greater hardenabilities than are realized. The fact that cases do arise in which the Grossmann method does not apply indicates that the fundamental hypothesis of the system may not be generally applicable. It seems advisable to re-examine not only Grossmann's system but also the concept of hardenability itself. Hardenability If steel parts are to possess a martensitic structure after quenching, they must first be austenitized and then cooled through the pearlite and bainite transformation ranges sufficiently rapidly to avoid the formation of pearlite, bainite, and pro-eutectoid products.* If, on cooling, these transformations are avoided, the resulting structure can consist only of martensite (and retained austenite). The hardenability of a steel is measured in terms of the severity of the cooling conditions necessary to avoid the pearlite and bainite transformations. The less rapid is the cooling necessary to prevent the formation of bainite and pearlite, the higher is the hardenability. The pearlite and bainite reactions appear to be differently affected by the alloying elements. Not only is this indicated by the published isothermal transformation data, but recent work by Zener2 affords a rational interpretation of the differing effects of the alloying elements. Manganese,3 for example, appears to decrease the rates of the pearlite and bainite transformations by equal percentages, while molybdenum45 is approximately 10,000 times more effective in retarding the pearlite than in retarding the bainite transformation, on the basis of isothermal measurements. In some steels, the formation of bainite restricts the formation of martensite while

Jan 1, 1947

By L. D. Jaffe, J. H. Hollomon

The hardenability concept has become widely used during the last few years for the choice and substitution of steels. Before the work of Grossmann,1 the systems for predicting hardenability from chemical composition could be used only over a narrow range of composition. Grossmann introduced a comprehensive system, which has been effective in calculating the hardenability of most types of moderate or low-alloy steels. However, occasions often arise that require the calculation of the hardenability of high-alloy steels from their chemical compositions. Experimental determinations of the hardenabilities of such steels indicate that the Grossmann system predicts much greater hardenabilities than are realized. The fact that cases do arise in which the Grossmann method does not apply indicates that the fundamental hypothesis of the system may not be generally applicable. It seems advisable to re-examine not only Grossmann's system but also the concept of hardenability itself. Hardenability If steel parts are to possess a martensitic structure after quenching, they must first be austenitized and then cooled through the pearlite and bainite transformation ranges sufficiently rapidly to avoid the formation of pearlite, bainite, and pro-eutectoid products.* If, on cooling, these transformations are avoided, the resulting structure can consist only of martensite (and retained austenite). The hardenability of a steel is measured in terms of the severity of the cooling conditions necessary to avoid the pearlite and bainite transformations. The less rapid is the cooling necessary to prevent the formation of bainite and pearlite, the higher is the hardenability. The pearlite and bainite reactions appear to be differently affected by the alloying elements. Not only is this indicated by the published isothermal transformation data, but recent work by Zener2 affords a rational interpretation of the differing effects of the alloying elements. Manganese,3 for example, appears to decrease the rates of the pearlite and bainite transformations by equal percentages, while molybdenum45 is approximately 10,000 times more effective in retarding the pearlite than in retarding the bainite transformation, on the basis of isothermal measurements. In some steels, the formation of bainite restricts the formation of martensite while

Jan 1, 1947

By J. D. Anthony

The Australian continent possesses significant reserves of a wide range of minerals, including bauxite, coal, copper, diamonds, gold, iron ore, lead, manganese, mineral sands, nickel, phosphate, silver, tin, uranium, and zinc. Australia's identified economic resources of many minerals are very large as indicated in Table 1. A sophisticated and highly experienced mineral industry is now an established feature of the Australian economy and Australia is the world's largest exporter of iron ore, alumina, mineral sands and refined lead and amongst the leading suppliers of many other commodities such as coal, lead and zinc ores/concentrates, nickel, refined zinc, tungsten concentrates and bauxite. The industry exports 70% of its production. This is reflected in the value of Australian mineral exports which have grown from about $200m in 1960/61, comprising 10% of total export receipts, to about $1265m or 29% of export income in 1970/71 to around $7061 representing 37% of Australia's total export income in 1980/81. Details of the more significant minerals are as follows: Japan (42.1%) USA (11.3%) ASEAN (6.3%) UK (5.9%) F.R. Germany (3.8%) Republic of Korea (3.4%) New Zealand (2.6%) Also see Table 2. AUSTRALIA'S MINERAL RESOURCES POLICIES Federal and State Governments' Responsibilities Australia has a federal system of government comprising six States, a self-governing Territory and a Federal Government. Under the Australian federal system the Constitution sets down the powers of the Federal Government. All powers not assigned to the Federal Government in the Australian Constitution reside automatically with the States. Certain of these broad powers result in the Federal Government having a significant influence on resources development. For example, in being responsible for economic management, the Federal Government's fiscal and monetary policies have an important effect on industry as well as on State finances. In particular, the taxation regime employed by the Federal Government is of direct importance to decision-makers in the resources industry. The Federal Government is responsible also under the Constitution for external trade matters; and international trade and commodity matters are increasingly important in Australia's international relationships. Foreign investment is another area where the Federal Government has a role to ensure that national interests are protected. This foreign investment power flows from the Federal Government's control of foreign exchange movements into and out of Australia. However, before enlarging on these and others of the Federal Government's powers and policies, it should be emphasized that the State governments, by virtue of their wide powers to regulate matters within their own boundaries, are more directly involved in the day-to-day administration and regulation of mining operations. For instance, the powers of the State governments include the responsibility-for the granting of exploration rights and mining leases, the approval of mining operations and the levying of royalties and other like charges. Administrative arrangements covering the granting of minerals and petroleum exploration and development titles vary from State to State. Before development rights are granted, State governments consider environment protection and rehabilitation aspects of development proposals. The provision of infrastructure within State borders is a matter primarily of State government responsibility. It is usual practice in Australia for State governments to construct and operate infrastructure services such. as railways, ports and electricity generation and transmission. The States may also provide certain public services such as electricity. and water, port and loading facilities, communications, health and education services which form part of the infrastructure of mining operations. In remote areas the mining companies themselves usually are expected to provide much of this infrastructure. However, the Federal Government is primarily responsible in some fields, such as telecommunications and parts of the railways network. State governments carry out preliminary exploration and geological mapping and some are directly involved in the mining of coal for power generation. The Federal Government's responsibilities in addition to economic management, taxation, international relations, foreign capital and investment, include regulation of exports, environmental matters and matters affecting the Aboriginals of the Northern Territory. FEDERAL GOVERNMENT POLICIES The continued sound development of the minerals and energy resources sector is regarded by the Federal Government as being of very great importance. However, the Government does not seek to participate directly in resource developments. It sees its role rather as that of establishing a sound economic and policy climate in which private companies can identify opportunities, seek out customers and marshall the necessary capital for the development of resource projects.

Jan 1, 1982

By H. A. Schwartz, W. Kenneth Bock

In this paper it is shown that when the tensile strength of a given steel in various states of heat-treatment is plotted against its elongation, a straight line results. The equation of this straight line can be computed with considerable accuracy from its chemical composition. The appropriate equations are given. The logarithm of the slope of the tensile-strength locus is shown to be proportional to the cumulative effect of the total alloy addition and the vosition of the line to be directly proportional to the cumulative effect of the alloy content. It is further pointed out that heat-treatment is more effective than composition in determining yield ratio. The latter enters mainly by its effect on hardenability, which is briefly discussed. Reduction of area and Brinell number are given some incidental attention. The data are applicable only to steels that have been normalized and/or quenched. The steels, if normalized, may or may not have been tempered. If quenched they must have been tempered at or above 4oo°C. (75o°F.). Introduction Cast steels vary in composition and frequently are used in various states of heat-treatment. It is obviously important to be able to predict the compositions that might accompany specific engineering properties by suitable selection of heat-treatments. For cast steels, which are of necessity produced heat by heat in accordance with the particular requirements of the castings to be poured, there has been, happily, much less tendency to standardization than for rolled products, whose destination is not necessarily known when particular ingots are made or rolled. It is of distinct advantage to the steel foundry-men to be able to make steel of given properties, using alloys that can be recovered from scrap, or most conveniently or cheaply bought, rather than a particular formula adopted in the interest of standardization. The heat-treatment appropriate to securing a given result in a given steel is well known to be closely related to composition. For example, molybdenum steels are not much softened by tempering except at rather high temperatures. Highly alloyed steels are "air-hardening," and on cooling in air behave like carbon steels that have been quenched. With these matters, we do not concern ourselves in this paper, although we recognize their importance. The entire picture evidently will be very complex and can be brought within accurate understanding only if our knowledge of test results can be coordinated in terms of general principles.

Jan 1, 1944

By H. A. Schwartz, W. Kenneth Bock

In this paper it is shown that when the tensile strength of a given steel in various states of heat-treatment is plotted against its elongation, a straight line results. The equation of this straight line can be computed with considerable accuracy from its chemical composition. The appropriate equations are given. The logarithm of the slope of the tensile-strength locus is shown to be proportional to the cumulative effect of the total alloy addition and the vosition of the line to be directly proportional to the cumulative effect of the alloy content. It is further pointed out that heat-treatment is more effective than composition in determining yield ratio. The latter enters mainly by its effect on hardenability, which is briefly discussed. Reduction of area and Brinell number are given some incidental attention. The data are applicable only to steels that have been normalized and/or quenched. The steels, if normalized, may or may not have been tempered. If quenched they must have been tempered at or above 4oo°C. (75o°F.). Introduction Cast steels vary in composition and frequently are used in various states of heat-treatment. It is obviously important to be able to predict the compositions that might accompany specific engineering properties by suitable selection of heat-treatments. For cast steels, which are of necessity produced heat by heat in accordance with the particular requirements of the castings to be poured, there has been, happily, much less tendency to standardization than for rolled products, whose destination is not necessarily known when particular ingots are made or rolled. It is of distinct advantage to the steel foundry-men to be able to make steel of given properties, using alloys that can be recovered from scrap, or most conveniently or cheaply bought, rather than a particular formula adopted in the interest of standardization. The heat-treatment appropriate to securing a given result in a given steel is well known to be closely related to composition. For example, molybdenum steels are not much softened by tempering except at rather high temperatures. Highly alloyed steels are "air-hardening," and on cooling in air behave like carbon steels that have been quenched. With these matters, we do not concern ourselves in this paper, although we recognize their importance. The entire picture evidently will be very complex and can be brought within accurate understanding only if our knowledge of test results can be coordinated in terms of general principles.

Jan 1, 1944

By F. R. Hensel

PURE silver and silver-lead alloys have been studied as to their suitability for bearings.1-8 A review of the properties of thallium and the silver-thallium constitutional diagram was made by the author to analyze the possibilities of silver-thallium compositions for antifriction materials.† The silver-rich end of the diagram as reported in the literature9-11 was found to be sketchy and it was necessary to carry out considerable experimental work to arrive at definite conclusions. Some of the results of this work are reported in this paper. TEST MATERIALS In the beginning of the work, only fused alloys were investigated. Later, research [TABLE I. Composition of Fused Silver thallium Alloys Tested for Antifriction Properties PERCENTAGE ALLOY No.OF THALLIUM 15330.48 153406 231 HT2.04 2312.10 232 HT3.83Balance 2324.07Silver 233 HT5.86 2336.38 2349.84 234 HT10.07] was carried out on electroplating methods and diffusion processes. In preparing the fused alloys, care was taken to exhaust the toxic fumes caused by the thallium content. The compositions of the series of fused alloys are listed in Table I. The silver-thallium alloys were melted in clay-graphite crucibles and cast into preheated steel molds of 3/4-in. diameter. In the cast condition, they showed a cored structure, as indicated by the micrographs of Figs. I to 3. The etching reagent used was a mixture of 2 grams K2Cr2O7, 8 c.c. H2SO4, and 100 c.c. H2O. The cored structure is unsatisfactory for the type of corrosion resistance required for bearing applications, and homogenizing experiments were carried out at various temperatures, the results of which are shown in Figs. 4 through 8. The alloys with a lower thallium concentration, which were heated for 2 hr. at 525°C. show an almost completely homogenized solid solution type of structure. With higher thallium concentration, the homogenizing temperature was dropped to 475°C. to eliminate the formation of a liquid phase. It is evident that heating for 2 hr. at this temperature did not result in complete elimination of the cored structure. As would be expected, cold-working of the cast structure is an expedient in establishing equilibrium conditions. The fine homogeneous grain structure shown in Fig. 7 corresponds to the cold-worked area under the Rockwell ball penetration when the hardness was taken before heat-treatment. A detailed structural study was made on a cast silver-thallium alloy containing 3.67 per cent thallium. Three micrographs (Figs. 9, 10 and 11) show the transition

Jan 1, 1945

J. M. Wadsworth,' Okmulgee, Okla. (written discussion).—It seems to me that thc young man must first be absolutely sure that the work he has taken up is to his liking and then I would advise that he get into the practical end of it and learn as much about it as he can as fast as he can. For instance, in the refinery business the college man, graduated in chemical engineering, should ground himself by going through the various departments in a refinery and working in them until he is thoroughly familiar with the operating problems. In a short time he would be able to apply many things which appear in the abstract form in his college work and this would opcn up an opportunity for him to capitalize on them, promoting his own interest. I do not criticize the present-day college men as a class, but I have found that many of them come into your plant with the idea that mere possession of a diploma should insure rapid promotion; in a short time they are impatient and usually leave. We have found in employing men that the single attribute most difficult to find in them is a lot of energy and whole-hearted interest in the work at hand, and it seems to me that if a man combines these with a careful technical training he should be fairly well equipped to gamble on his future. They must learn that the biggest satisfaction to be gained in life is in their work. Procedure for Attaining Objective of Young Petroleum Engineer H. B. Fell,+ Ardmore, Okla. (written discussion).—Of course, the first thing to be ronsidered in any proposition is the ultimate objective that is desired to be attained. 1 presume that the desired objective of most of the young men graduating in petroleum engineering will be that of chief executive of one of the companies in the petroleum industry, or one of the allied industries, or to become an independent oil producer, or oil refiner, or possibly an oil distributor. The next phase then to be considered is the procedure which should most logically be followed to attain the objeckive of the indivitlual, since in these cases these young men will have been trained in a course in petroleum engineering and it would logically be presumed that the attainment of their objective should be through the operating end of the branch of the business with which they are connected. The operating end is, of course, the department of each branch of the business that develops the resources, or refines the products, or distributes the products, from which the profits are derived, and is a part of any business which is filled with enough interesting work to appease the desires of the most ambitious young men. In order to get the best possible training it would appear to me that the place for a young man to start after graduation would be at the bottom of that branch of the industry which he expects to follow. For example, if he is going in the producing end he can gct no better training than is secured by starting as a roustabout in the ficltl, where he romes in constant rontact with the character of work that is necessary

Jan 1, 1928

By David J. Mack, T. V. Philip

The effects on the Cu-A1 eutectoid transformation of the addition of a third element from the second long period and from Group IIB of the periodic table, were studied by isothermal transfomation techniques. The valency of the third element shows the most pronounced effect on the eutectoid decomposition. With some exceptions, the atomic size factor of the third element shows some consistent effects on pearlite nucleation and growth. The atomic concentration or the electronegative valency of the third element shows wo consistent effect on the eutectoid decomposition. Addition of the third element helps spheroidization of pearlite. SINCE the pioneering work of Davenport and Bainl on the eutectoid decomposition in steel by the isothermal transformation technique, an enormous amount of data has been accumulated on the eutectoid transformation characteristics of commercial steels. While the eutectoid reaction in steel is of tremendous industrial importance, it appears to be quite unique among the eutectoid reactions. Though the metal-lographic structures developed in the Fe-C and Cu-A1 eutectoids are similar, it is now evident that the two eutectoid reactions are quite dissimilar. The eutectoid decomposition in the Cu-A1 system is more complicated partly due to the appearance of transitional phases in addition to the equilibrium phases. * The first isothermal studies of aluminum bronzes were made by Smith and Lindlief2 and later by Mack,3 Klier, and Grymko,4 and recently Hayne 5,6 A few other systems, structurally analogous to the above, have been studied by the same technique.7-10 Kasberg and Mack1' studied the effects of iron on the transformation of commercial aluminum bronze. The effects of manganese and nickel on this aluminum bronze and those of iron, manganese, and nickel on the binary Cu-A1 eutectoid have been recently studied.12 The object of the present investigation was to study, by isothermal transformation techniques, the effects (with respect to the fundamental factors of alloy formation) of the addition of a third element on the transformation of a Cu-Al eutectoid alloy, 11.8 pct Al. The third elements chosen for the purpose were silver, cadmium, indium, tin, and antimony from the second long period, and beryllium, zinc, and cadmium from group 11B of the periodic table. They were added in nominal amounts of 0.5, 1.0, and 2.5 pct by weight to a eutectoid Cu-A1 alloy. These third elements were expected to show the effects of electron valency, atomic size factor, and electronegative valency effects on the binary eutectoid transformation. PFLEPARATION OF ALLOYS AND PROCEDURE All alloys were made as 400-g heats by induction melting in a graphite crucible with a graphite lid. The molten alloy with a layer of graphite powder on top was stirred at regular intervals by a graphite rod. When the melt was judged to have acquired sufficient superheat, a pinch of common salt was sprinkled on top and any crust scraped off to one side. It was then chill cast into a 5/8 in. rod. The alloys with silver were prepared by remelt-ing the high-purity Cu-A1 eutectoid alloy used by Mack3 with high-purity silver (99.99 pct pure from Hardy and Harmon, Inc.). In the preparation of all the other alloys, polished electrolytic copper shot (from Belmont Smelting and Refining Co.) and high-purity aluminum (99.99 pct pure from Aluminum Co. of America) were used.

Jan 1, 1962

By T. D. Tiemann

The chemical and mineralogical composition of Caribbean bauxite ores are described. Extraction of alumina by several processes from both Haiti and Jamaica bauxites is discussed and data presented. IMMENSE deposits of bauxite occur in the Caribbean islands of Hispaniola and Jamaica in the high plateau lands and have been excellently described by 0. C. Schmedeman.' The bauxite occurs as deposits in catchments or etched depressions in Tertiary limestone believed to have been deposited in the Eocene and Oligocene periods.' In appearance both the Haiti and Jamaica bauxites resemble a relatively high iron clay and have indeed been mistaken for such.' They are very soft and friable and disperse readily on vigorous agitation in water. The color range in general is light brown to red. Chemically, the outstanding characteristic of the bauxites is the low silica and high ferric oxide content. The extremely low silica makes them particularly valuable for the production of alumina in the Bayer plant since silica is responsible for the loss of both alumina and soda chemically combined as XNa,OYSiO2,ZAl2O2. The ferric oxide, only traces of ferrous iron are present, offers no interference in the production of high grade alumina. Typical oxide analyses of three types of ore are given in Table I2 and a list of the elements occurring in spectrographic quantities in Table 11." The size of the individual particles in the ore makes successful petrographic examination extremely difficult. The ores contain some relatively coarse grains of heavy minerals such as ilmenite, magnetite, and rutile, but other than occasional crystals of a few microns, the greater portion of the minerals are submicroscopic in size and approach colloidal dimensions. The mineralogic composition of the ores has been investigated by X-ray and differential thermal analysis.' These investigations indicate that the predominant mineral phases present are gibbsite (A1203.3H2O), boehmite (Al2O3.H2O), hematite (Fe2O3), and goethite (Fe2O3-H2O). There is no evidence of the occurrence of diaspore (Al2O3.H2O) in either the Haiti or Jamaica ores, but some type of "amorphous" alumina may be present in some of the bauxites of Jamaica." The temperature stability regions in the alumina-water system have been investigated and are given in recent literature. In the temperature range where the hydrated forms are stable, as determined by hydrothermal bomb methods," ibbsite is the stable phase to 155°C (311°F), boehmite from 155°C (311°F) to 280°C (536oF), and diaspore from 280°C (536°F) to 450°C (842°F). Although quite similar in many characteristics, the Haiti and Jamaica ore show a divergence in mineralogic composition that is reflected in the extractability of the alumina described in later paragraphs. Two principal differences occur in mineralogic composition. The iron-bearing mineral in the Haiti ores is predominantly hematite, while in the Jamaica ores goethite is predominant.4 Directly related to the extraction of alumina are the two minerals, gibbsite and boehmite. Boehmite is relatively high in the Haiti ores and in some of the less soluble Jamaica ores, while gibbsite predominates in the ores in Jamaica amenable to the American Bayer process of extraction. Pedersen and Related Processes In general, all processes for the extraction of alumina involving sintering or fusion of bauxite ores with limestone, soda ash, or a combination of limestone and soda ash followed by leaching, are based on the formation of alumina compounds that. yield alumina soluble in the subsequent leach. The principal idealized reactions in respect to alumina and silica for the three types of processes are as follows: Soda Ash Sinter: A12O3 + Na2CO3 = Na2O-Al2O, + CO2 SiO2 + Na2CO3 = Na2O . SiO2 + CO2 A12O2 + SiO2 + Na2CO3 = Na2O.Al2O8. SiO2 + CO2 Leach (with excess water): H2O + Na2O-A12O3 = 2 NaOH + A12O3 (insolution) H2O + Na2O-SiO2 = 2 NaOH + SiO2 (in solution) Soda Ash— Limestone Sinter: Na2CO2 + A12O3 = Na2O.A1203 + CO2 2CaCO3 + SiO2 = 2CaO . SiO2 + 2CO2 Leach (with excess water): Na2O' A1208 + H2O = 2NaOH + A13O3 (in solution) These latter reactions are the basis of the sinter process currently used for the recovery of soda and

Jan 1, 1952

By R. S. Craig, W. E. Wallace, G. S. Kamath

The destruction of long-range order in Mg-Cd, has previously been thought to occur as a second order process. In the present work a variety of X-ray diffraction techniques are employed to show that in this case and in Mg-Cd alloys containing frorn 20 to 33 1/3 at. pct Mg the process more nearly resembles an ordinary first order phase transformation. It is found that the ordered alloy, which occurs as a single phase at lgw temperatures, transforms with increasing temperature into a Cd-enriched disordered (P) phase and an Mg-enriched ordered (a) phase. The interval over which these two phases coexist under apparently equilibrium conditiovs extends from 25" to 87°C content. At 33 1/3 at. pct Mg the two-phase region has disappeared. Measurement of the long range order parameter, s, for the ordered phase in MgCd, (from superlattice line intensities) shows that it disorders only very slightly before it is transformed into the p form. Kinetic experiments reveal that when the a phase is formed frorn the p phase by suitably quenching so as to suppress phase segregation, the transformation is essentially complete and the a phase has acquired its equilibrium value of S in less than 1 min. In an earlier investigation carried out in this Laboratory1 the rate of disordering of the MgCd3 superlattice was determined over an extensive range of temperature. The process was found to be first order and the rate constant, k, was established. At the lowest temperatures studied k was found to increase exponentially with temperature. At higher temperatures, however, it passed through a maximum and for the 100 deg interval below the point at which the superlattice was destroyed k was observed to decrease with increasing temperature. The various theoretical treatments1-3 of order-disorder phenomena lead to a negative temperature coefficient for k near the superlattice critical temperature but this region for MgCdB seemed unusually wide. Detailed analysis of the point indicated' that either the long-range order parameter, S, for MgCda varied with temperature in an anomalous way or the disordering in this instance is more complex than in the cases which have been treated theoretically. The original objective in the present work was simply to determine S vs temperature for MgCda to ascertain whether the disordering was in conformity with theoretical expectations.2° In an early stage of the work it was noted, however, that under equilibrium conditions ordered (a) and disordered (0) phases coexist in MgCd, over a considerable range of temperature. Since on thermo- dynamic grounds the coexisting phases must differ in composition, the investigation was enlarged to permit the compositions of the two phases in MgCd3 to be determined and to establish the extent of the two phase regions for alloys containing from 20 to 33 1/3 at. pct Cd.

Jan 1, 1963

By R. J. Wygal

A method is presented by which homogeneous, isotropic, and reproducible aggregates of particles such as glass beads, sand, ground glass, etc., may be prepared simply and quickly by using a "particle distributor". Several applications of the packing method to the construction of model reservoirs are described. The flow characteristics of these packings me given. Some factors which limit the usefulness of unconsolidated packs for simulating reservoir rock are overcome through artificial cementation of the aggregates. INTRODUCTION Many laboratory studies of porous media are based on experiments using test packs of sand, glass beads and other granular materials. More confidence can be had in the results of such studies if the test packs are known to have uniform properties throughout, to be mechanically stable and to be accurately reproducible. This paper presents a method by which such packs of a variety of shapes and sizes may be constructed using a particle distributor. Some factors which limit the usefulness of unconsolidated packs as a means for simulating reservoir rock are described. A method of overcoming these limitations, which involves artificial cementation of the packs, is presented. DEVELOPMENT Particles packed by the tamping or vibrating techniques are usually either non-uniform or mechanically unstable. An invention by Currie and Gregoryl overcomes these difficulties to some extent. The invention is based on the use of a stream of falling particles impinging on and passing through a distributor matrix of several layers of closely spaced spheres. The particles are well dispersed by numerous collisions with the spheres. They become homogeneously distributed at some distance below the distributor matrix and at that position are collected in the sample container. This apparatus, however, was found to be ineffective when small particles were used since small particles accumulate on the top surfaces of the spheres. An improved distributor matrix was made, first in the form of a stack of five sieves, and then in the more adaptable form of spaced layers of wire screen. Fig. 1 shows a longitudinal view through a five-layered distributor of eight-mesh wire screen. This device gives excellent results.* Fine particles pass through the distributor with very little hold up. The fine structure of the wire matrix with its many deflecting surfaces ensures good particle distribution. There are no dead areas immediately below the screen as were sometimes observed to occur below a matrix of spheres. Using such a device, 20-30 mesh sands were packed to a porosity of 32.1 per cent at rates varying from 0.17 to 6 lb/rnin. The lowest porosity achieved by tamping small increments of similar sands into a container was 33 per cent. Motion pictures at 3,000 frarnes/sec of the surface of a growing pack of 2-3/4 mm glass beads have helped to show the mechanism by which packs of low porosity are obtained. The beads, although packed at the rate of 5 lb/min, were observed to hit the pack surface singly, for the most part, and at well spaced points of impact. Part of their energy is transferred to surface beads which are thereby

By T. C. Russell

The Conda phosphate mine, eight miles north of Soda Springs in Caribou County, Idaho, was opened up by the Anaconda Copper Mining CO. in 1920. Except for brief periods, during the 20's and early 30's, the mine has maintained a continuous production, and 2,100,000 short tons of phosphate rock have been shipped to the company's phosphate fertilizer manufacturing plant at Anaconda, Mont., or to independent processing plants on the Pacific Coast; a small tonnage of the rock has been shipped to the Hawaiian Islands. The Phosphoria formation on the Conda property consists of two, commercial-grade phosphate beds separated by 147 ft of black to brownish colored phosphatic calcareous shales interbedded with softer mudstones, clays, and occasional narrow seams of oolitic phosphate. The main lower phosphate bed in the series averaging 7.1 ft in thickness, is called the "foot-wall bed," which lies coriformably on the Wells limestone formation, the 1atter often containing irregular bands of chert. The upper or " hanging-wall bed" of phosphate rock averaging 7.2 ft in thickness, is overlaid by thick quartzite beds, locally called the " Rex chert" member in the upper portion of the Phosphoria formation. (Fig 1.) There are two anticlines on the property with axis striking approximately parallel to the mountain range beneath which extensive development on phosphate rock has been conducted in the past, and is now in progress. The phosphate beds have been eroded to a large extent from the tops of these anticlines, leaving at least three well-pronounced outcrops of the phosphate beds exposed within the boundaries of the Anaconda Copper Mining Cornpany's properties. At present, mining operations in the Conda No. 3 mine are confined to the two phosphate beds along the east flank of the easternmost anticline, where the dips on the beds vary from 50° to 60° east, thereby affording favorable conditions for the sublevel mining system now in use. Mining operations formerly were confined to the footwall or lower oolitic phosphate bed because of its higher phosphate and vanadium contents (32 pct P²O5 and 0.29 pct V2 O 5); this bed averages 7.1 ft in thickness. The oolitic portions of the upper bed were of satisfactory grade, but the shale and clay partings (Fig 2) diluted the mined rock and could not he separated economically by selective mining or by sorting. Experiments in beneficiating this rock were carried on for a number of years. Recently, a simple washing process was adopted, which gave a satisfactory grade of concentrates and a high recovery of P² O5. In 1947 it was decided to expand Anaconda's production of treble superphosphate and phosphoric acid by approximately 90 pct. This rock will be obtained from the footwall and hanging-wall beds, and the rock from the hanging-wall bed will be benefici-ated at -Anaconda.l In order to take advantage of the previous development on the 500 secondary haulage level, short crosscuts will be driven at approximately 950 ft intervals from the existing lateral drifts through the hanging-wall shale beds. From the inner end of each crosscut, short lateral drifts will he driven in both directions, so that four working raises can he put up on the dip of the phosphate bed at proper intervals along each of the lateral drifts. The mining operation on the footwall bed at Conda

Jan 1, 1950

By R. E. Reed-Hill

The lattice reorientations in (1011) and (1013) twins of pure magnesium have been investigated using polarized light. Both forms (Ire subject 20 almost complete second-order twinning on the (1012) plane of the first-order twin. The observed deviations of composition planes by 6 and 3 deg, respectively, from coherent twinning planes are caused by second-order twinning. The experimental data indicate that (1011) and (1013) are reciprocal twins with a twinning shear 0.136. In a previous paper1 it was shown that the primary fracture mechanism in single crystals of magnesium strained in tension parallel to the basal plane is parting or fracture inside twins. In the temperature interval 25oto286oC, the observed twinning form, dominant in fracture, was a very small twin which formed in bands. Because these twins were very small and appeared in extensively deformed regions they did not lend themselves to X-ray analysis. Lacking Cou-ling and Pearsall&apos;s2 recently reported polarized light technique for magnesium, the twinning plane indices (K1) were originally determined by two surface composition plane measurements. This plane fell in a major zone (axis < 1120>) at an angle of 55.75 deg to the parent crystal basal plane. Because its habit deviated by 6 deg from{l0ll), 61.9 deg, the experimental data per se were not consistent with simple (1011) twinning and, for expedience, the twin was designated with habit plane indices (30341, 54.5 deg, representing the lowest set of indices corresponding to measured angles. Couling, Pashak, and sturkey3 have also found bands of reoriented lattice with a similar habit in polycrystalline specimens of magnesium and certain dilute magnesium alloys. These bands are significant because their formation in large numbers during plastic flow permit specific magnesium alloys to undergo very extensive deformation by cold rolling. Using polarized light2 they showed that the basal plane in the reoriented material was nearly parallel to the band habit and, as a result, proposed a mechanism for band formation involving a double twinning process in which (1011) twins form and then retwin according to (1012). Because of the obvious similarity between the twin bands observed in single crystals and in polycrystalline specimens, it was decided to investigate if the two phenomena were not identical and, if possible, to verify the retwinning hypothesis. The present paper is a report of this investigation and shows that the twins with the (3034) habit correspond closely to retwinned (l011) twins. Evi- dence is also given for an analogous retwinning process in (1013) twins. EXPERIMENTAL PROCEDURE Rectangular single-crystal specimen deformed in tension (stress axis in the basal plane parallel to [1010], as previously described,4 were polished electrolytically by Jacquet&apos;s method5 and etched in acetic picral.2 All twins studied in this investigation belong to a major zone, whose axis, [1210], was perpendicular to both stress axis and two sides of each specimen [(1210) surfaces]. These latter contain the plane of shear of the twins and measurements of the basal plane trace of twins on these surfaces determines the lattice orientations of the twins. The position of the basal plane in each case was determined with a polarizing microscope using a modification of the technique of Couling and Pearsall.2 For each twin the four positions of maximum extinction were measured, the data averaged, and then the pair of extinctions corresponding to the basal plane was determined by rotating the microscope stage and observing the position at which the color changed from orange to blue with a gypsum red, first-order plate inserted between the crossed Nicol prisms. EXPERIMENTAL RESULTS (1013) Twins—In general, especially in speci-mens deformed at 150°C, (1073) twins appear in greater numbers and larger sizes than (1011) twins, and the lattice reorientation inside these twins is therefore easier to study and measure. Fig. 1 shows an area of an unetched and unpolished (1210) crystal surface containing a number of (1073) twins sloping upward to the right at about 29 deg with the basal plane of the original crystal (horizontal direction). Slip line segments may be seen in both the parent crystal (running horizontally) and in the twins (sloping downward to the right at approximately -22 deg with the horizontal). As may be seen in Fig. 2, the slip lines in the twin are not at the proper angle (64 deg from basal plane of the

Jan 1, 1961

By G. Rinelli, A. M. Marabini

A wide-ranging series of experiments has been carried out on value minerals (sphalerite, smithsonite and hematite) and gangue minerals (quartz and calcite) to assess the properties of various commercially available vegetable and synthetic tannins as dispersants for these minerals in a finely ground state (<5 microns). Experiments to determine the dispersing power of each reagents on every mineral have been performed through sedimentation tests run first in water and afterwards in the presence of a collector having specific action on the mineral concerned. The tests have been extended to a wide range of dispersant concentrations, maintaining the pH and collector concentrations at the levels known to be the best for the flotation of the various minerals. By comparing the results obtained on each mineral, conclusions have been drawn on the possibility of using different classes of vegetable and synthetic tannins in the selective flotation of fine particles. These results have been related to the structure of the tanning compounds and to the surface properties of the minerals.

Jan 1, 1980