Search Documents

By Glenn Keep

THIS paper is not an announcement of the successful conclusion of the Cerro de Pasco Copper Corporation's pacos-pyrite problems, but merely a description of the commercial-scale, intermittent-roasting operations conducted by the writer, J. H. Lucas and others of the staff. It was prepared by request, for presentation at the February meeting of the Institute. The results obtained in Peru confirm the 1-ton-a-day experiments completed about three years ago at Kearny, N. J. by C. C. Gordon and Mr. Lucas, where it was first demonstrated that a mixture of about 80 per cent. pacos ore with 10 per cent. pyrite ore and 10 per cent. salt could be roasted intermittently in a small 1-ton-a-day Holt-Dern furnace without extraneous fuel, producing porous calcine that could be leached rapidly. Mr. Keep and his staff, by successfully introducing improvements in the construction of the commercial furnace and in their handling of material, have established beyond doubt a low cost for roasting. The other steps in the process of treating pacos and pyrite ores have not as yet been demonstrated as sufficiently conclusive to warrant their acceptance for a permanent plant.

Jan 1, 1929

By Robert A. Rapp, Ronald L. Pastorek

Solid-state electrochemical measurements by three alternative experimental procedures were made with the cell FeO, Fe3O4 |Zro.85Cao.15O1.85 |Cu| Zr0.85CaO.15O1.85 | FeO, Fe304 to establish the solubility and diffusivity of oxygen in solid copper in the temperature range 800" to 1030°C. The solubility of oxygen in solid copper and the diflusivity of oxygen in solid copper Dgu = 1.7 X 10-2 exp(-16,000/RT) Cm2/sec were determined and confirmed in alternative experiments. The enthalpy of solution of oxygen in solid copper equals —10,000 cal per mole; the partial excess entropy of the oxygen atoms in the Cu-O dilute solution is approximately the same as that found for interstitial atoms in other metals. The diffusivity of oxygen in solid copper is consistent with that expected for an interstitial atom. RELIABLE values for the saturation solubility N(s) and diffusivity DO of oxygen in solid copper have not been unambiguously established in the literature. Following three early determinations by others,1"3 Rhines and Mathewson4 reported that the solubility of oxygen in solid copper increased from 0.007 at. pct 0 at 600°C to about 0.015 pct at 1050°C. Phillips and skinner,, using essentiially the same analytical procedure, reported that the solid solubility increases from 0.0018 at. pct 0 at 550°C to about 0.0075 pct at 1050OC. The only previous value for the diffusivity of oxygen in solid copper was reported by Ransley.6 Ransley deoxidized Cu-Cu2O alloys in an atmosphere of carbon monoxide gas to yield a solubility-diffusivity product. He used the solubility data of Rhines and Mathewson to calculate the diffusivity values. Another method for obtaining the solubility-diffusivity product (N(s) DO) is by measuring the widths of internal-oxidation zones in copper alloys as reported by Verfurth and Rapp.7 However, the calculated N(S)Do products depend upon the alloy content of the specimen, so that the internal oxidation of copper alloys does not follow ideal internal oxidation kinetics. As a result, unequivocal values for the N(s) DO product were not obtained by this procedure. A solid-state coulometric titration technique similar to that employed in this work was introduced by C. Wagner8 to study the dependence on silver activity of the Ag/S ratio in silver sulfide in the temperature range of 160" to 300°C. Similar experiments have been carried out by C. Wagner and co-workers9-11 to study the stoichiometry range of silver and copper tellurides, cuprous sulfide, and cuprous selenide. Numerous authors have carried out electrochemical measurements with a solid oxygen-ion-conducting electrolyte to determine the solubility and/or diffusivity of dissolved oxygen in several liquid metals.12-l6 Rickert and Steiner17,18 have used solid-state electrochemical measurements to determine the diffusivity of oxygen in solid silver from 760" to 900°C. Two different cell geometries were used. In the cell of linear geometry Fe, FeO | ZrO2 + (CaO) | Ag + [0 (dissolved)] [1] oxygen diffused from the interior of the silver electrode to the silver/electrolyte interface where the oxygen activity had been lowered from a fixed initial value to practically zero by the application of voltage to the cell. The diffusivity of oxygen in solid silver was determined from the solution of the diffusion equation and the time dependence of the cell current. However, this determination of the diffusion coefficient depended upon a knowledge of the solubility of oxygen in solid silver. A cylindrical geometry was used for the cell Pt, O2(Po2 = 0.21 atm) | ZrO2 + (CaO) | Ag + [0 (dissolved)] [II] which also allowed the diffusivity of oxygen in solid silver to be determined. These values were in agreement with other available data.l9 Recently, Raleigh20,21 used a method involving the measurement of diffusion-limited currents in a cell involving the AgBr solid electrolyte to determine the diffusion coefficient of silver in Ag-Au alloys at 400°C. Diffusivity values on the order of l0-14 sq cm per sec were measured in the alloy composition range 10 to 60 at. pct Ag in a single experiment. From numerous electrical conductivity and galvanic cell measurements,9'22"26 the solid solution Zr0.85 Ca0.15 O1.85 has been established as an electrolyte with predominant oxygen ion conduction over a wide range of intermediate and high oxygen activities. For interrelating the thermodynamics and the kinetics of the dissolution of oxygen in solid copper in this investigation, a galvanic cell was constructed with FeO-Fe3O4 as the reversible reference electrode, the Zr0.85Ca0.15 O1.85 electrolyte, and a pure copper specimen under-saturated in oxygen as the other electrode. THEORETICAL ANALYSIS Three variations of a high-temperature electrochemical technique were used in this study to provide two determinations each of the solubility and diffusivity

Jan 1, 1970

By J. P. Myers, A. H. Flagg, E. S. Mardock, J. L. P. Campbell, J. M. Terry

The development process for the use of radioactive tracers as a means of locating zones of permeability is discussed. The general techniques for the safe handling of radioactive materials is given as developed by the Lane-Wells Co. and Well Surveys, Inc. The prob1em and. successes with tracers in waterflood systetns, oil and gas injection profiles, fracture sand tracing, squeeze (ement tracing. lost circulution, and cement top localion are discussed and illustrated. INTRODUCTION The exact location of the permeable zones lying within the productive horizon has been a major problem faced by the petroleum engineer for decades, and it has been a problem which has seldom been solved with certainty. Reservoir engineers usually have to incorporate a question mark in their estimates of future reservoir performance because of blanks in the core data. Although the use of radioactivity or electrical logs for the estimation of porosity has been of great assistance in furnishing a record for the reservoir engineer, this application of logging data has not completely solved the problem. In short, the industry needs an in-situ well surveying method which can locate and estimate the permeability of the zones existing within a given pay section. The initial development work with radioactive tracers has been towards filling the need for permeability information. Progress to date permits the location of permeable zones with a qualitative estimate of their relative importance with respect to permeability. The calibration of the method is still incomplete. but present development work on tracer preparations, borehole effect correction factors, and instrument limitations give a promise of quantitative "permeability profiles" in the near future. The development work on the radioactive tracer method discussed here began several years ago in the laboratories of Well Surveys, Inc., in Tulsa. At the outset of this work, three approaches to the problem were visualized as follows: 1. A fluid carrying a soluble, chemically inert, gamma ray emitting isotope is pumped down the borehole and out into the permeable zones of the formation. The greater gamma activity of the permeable zones thus permits them to be differentiated from the impermeable zones which contain no active tracer. It was found difficult to obtain a tracer material which was chemically inert. Absorption to some degree was noted in all experiments. Also, it proved impossible to hold the tracer near the horehole where it could be logged. 2. A fluid carrying a soluble, gamma ray emitting isotope is pumped down the borehole into the permeable formations. In contrast with proposal 1, above. the tracer is chemically active with the fluids and materials in the pore spaces of the permeable zones. The permeable zones are thus indicated by their higher radioactivity level. The main difficulty in this proposal was finding a tracer material which would not be absorbed by shale as well as in the permeable porosity. Very little field work was done with this system. 3. Radioactive particles suspended within the injection fluid are pumped down the well. As the fluid enters the permeable formations, the radioactive particles are filtered out on borehole wall. The permeable zones are differentiated from the impermeable by the gamma ray activity deposited on the formation wall.

Jan 1, 1956

By S. N. Kesten, Richard Murphy, A. H. Land, W. F. James

Introduction—by W. F. James and A. H. Lang This paper describes the geology and present state of development of uranium and thorium deposits in Canada. It is expected that this information will be added to that now being assembled from available American and British data to provide a background for engineers and others who may be called upon in the future to examine or search for radioactive deposits. Some generaliza- tions regarding the Canadian deposits are included, but many of these are necessarily tentative. The information contained in the paper is up to date for the end of 1948. The information contained in this paper has been derived from many sources. Much of it is from the records of the Canadian government-owned Eldorado Mining and Refining (1944) Limited and from examinations of government and private properties made by officers of the Geological Survey of Canada. Some information on privately-owned properties has been quoted from other sources mentioned in the text. The information has been assembled by W. F. James of Eldorado Mining and Refining (1944) Limited and A. H. Lang of the Geological Survey of Canada, who have written the sections for which they are credited. The description of the Eldorado mine is based on reports by Richard Murphy, formerly chief geologist for Eldorado; the report by Mr. Murphy was published previously by the Canadian Institute of Mining and Metallurgy,' to whom the writers are indebted for permission to repub-lish. The section dealing with the geology of and development work in the Goldfields area, where Eldorado has important holdings, is by S. N. Kesten, field geologist for Eldorado. The geological diagram of the Goldfields area (fig. 2) was kindly supplied by A. M. Christie of the Geological Survey of Can-

Jan 1, 1951

By W. F. James, Richard Murphy, S. N. Kesten, A. H. Land

Introduction—by W. F. James and A. H. Lang This paper describes the geology and present state of development of uranium and thorium deposits in Canada. It is expected that this information will be added to that now being assembled from available American and British data to provide a background for engineers and others who may be called upon in the future to examine or search for radioactive deposits. Some generaliza- tions regarding the Canadian deposits are included, but many of these are necessarily tentative. The information contained in the paper is up to date for the end of 1948. The information contained in this paper has been derived from many sources. Much of it is from the records of the Canadian government-owned Eldorado Mining and Refining (1944) Limited and from examinations of government and private properties made by officers of the Geological Survey of Canada. Some information on privately-owned properties has been quoted from other sources mentioned in the text. The information has been assembled by W. F. James of Eldorado Mining and Refining (1944) Limited and A. H. Lang of the Geological Survey of Canada, who have written the sections for which they are credited. The description of the Eldorado mine is based on reports by Richard Murphy, formerly chief geologist for Eldorado; the report by Mr. Murphy was published previously by the Canadian Institute of Mining and Metallurgy,' to whom the writers are indebted for permission to repub-lish. The section dealing with the geology of and development work in the Goldfields area, where Eldorado has important holdings, is by S. N. Kesten, field geologist for Eldorado. The geological diagram of the Goldfields area (fig. 2) was kindly supplied by A. M. Christie of the Geological Survey of Can-

Jan 1, 1951

By Edgar S. Cook

At the close of the Bethlehem Meeting, the writer was experimenting with large fuel-charges, 4000 Ibs. basis, as compared with 2000 Ibs., hot had not made sufficient progress to draw any safe conclusions. Previously me had always used 2000 Ibs. fuel, the ore-burden being proportioned to this as a basis. I could never persuade myself that there was any advantage to be derived from following the more popular method of larger fuel-charges. Our men were accustomed to the old way of filling ; and we did not care to run the risk of the errors likely to follow any alteration in routine work, particulary as I could not, by my course of reasoning, discover ally compensating gain. Nevertheless, after reading Mr. Gordon's discussion of Mr. Birkinbine's paper, '' Operations of Warwick Furnace from August 27th, 1880, to September 1st, 1885" (Transactions, xiv., 833), I determined to test by actual experiment the value of large fuel-charges : the change was made in the week commencing March 28th, 1886, and continued until July 25th, about four months. The fuel and ores remained during the trial the same as had been used before, and have been used since. For the first two weeks, the furnace worked with great regularity, giving excellent results, exceeding those of the two weeks immediately preceding. But for my remembrance that the furnace had on former occasions worked with equal uniformity for longer periods without any apparent reason, I should doubtless have concluded that this improvement was due to the different method of filling and congratulated myself that a means had at last been found to prevent inconvenient "dirt" accumulations. Before abjuring my previous skepticism, however, I resolved to pursue the trial further. The fourth meek developed the peculiar conditions that had prevailed previous to the change; and these continued with more or less frequency during May, June and July. At last, finding no improvement over the smaller charges—no change in fact for better or for worse—I commenced filling the 2000 lbs. fuel-charge in the latter part of July, and have continued it up to present writing, September 4th.

Jan 1, 1887

R. V. Norris, Wilkes-Barre, Pa. (communication to the Secretary*):—Mr. Stow's paper presents a series of arguments, numbered from 1 to 18, concerning the relative merits of four systems of colliery-ventilation, designated by the author as " plain pressure-ventilation," " plain exhaust-ventilation," " obstructed pressure-ventilation," and " obstructed exhaust-ventilation." These arguments are subsequently compared by means of tables, in which an arbitrary numerical value is assigned to each, and which consequently serve no other purpose than that of showing his opinions and predilections, as indicated by his assignment of the said numerical values. In addition to this general summary, Mr. Stow intimates his preference for a fifth method of colliery-ventilation—namely, what he calls " alternating pressure-ventilation," which consists in the running of the fan at "pressure " during working-hours, and as an " exhaust" between shifts—a system which he proposes as, perhaps, new, yet which he thinks deserves recognition " as a standard form." This proposed " standard form " is not to be found in practice ; and I think it would be impracticable in gaseous mines of large extent, for the following reasons: 1. It takes considerable time to reverse the air-current in a large mine; and the reversal would involve a period of complete stoppage of ventilation, long enough to permit serious accumulations of gas. 2. In shaft- and slope-mines, at least, it is hardly practicable to have " every man out of the mine" during the night, and certainly impracticable to avoid keeping mules and horses inside. 3. The doors necessary to divide and direct the air-current are properly hung to open against the air-pressure; and, unless

Jan 1, 1910

By C. McCulloch

OPEN-PIT mining of coal is relatively a recent innovation; men still active in the industry can trace its development. Re- viewing the growth of operations from the original horse-drawn scrapers, through the various stages of power equipment to the huge strip- ping shovels of today, one also notes changes in the methods of what the coal man calls preparation at the face. We really should not call it face preparation because, in contrast to underground mining, a face does not exist in strip mining. Further, preparation of the coal for market at the loading point has already, in but a few years, become largely of historic interest only and modern mines as well as old mines recently modernized rely almost entirely on separate and elaborate preparation plants to produce marketable coal. This practice was not voluntarily adopted by the producer but was forced upon him by the inadequacy of previous

Jan 1, 1939

By Gregoire Gutzeit

THE development reported in this paper was begun by the author a number of years ago, while he was a lecturer on complex chemistry and metallurgy at the University of Geneva, Switzerland, and in charge of that institution's research laboratory. Completion of the development and reduction to practice did not occur until last year at the Westport mill, laboratories and testing plant of the Dorr Company, where this method is now in general use for identifying and localizing the mineral constituents of both metallic and nonmetallic ores. It has proved to be a practical tool of the metallurgical staff at the Westport mill, devising unusual milling flowsheets for complex and refractory ore bodies. In a number of instances the findings have been successfully used as fundamental factors in the design and specification of complete metallurgical plants. Seven examples of the use of this method in solving practical milling problems are included in this paper. GENERAL OUTLINE The microscopic study of an ore, at first only of scientific interest, has proved extremely useful both in practical geology and in ore dressing. The binocular magnifying lenses for rough observation of the products of an ore-dressing plant have been in use for a long time; but only within the last few years has a systematic microscopical examination of ore samples become a normal tool of any research laboratory dealing with ore-dressing problems. Such an investigation avoids considerable loss of time as well as empirical trials and useless experimentation. It will generally indicate the correct grinding and often will suggest the proper method of treatment. The petrographic determination of transparent minerals in thin sections, or even in grains, has been perfected, and very accurate methods have been devised to meet any requirement, such as Feodorof's rotating stage on the petrographic microscope. Almost all transparent minerals can be positively identified by their optical properties; i.e., isotropism, anisotropism, color, pleochroism, refractory index, cleavage, crystal form, birefringence, and others. The identification of opaque minerals is a much more difficult problem and can be done only by using polished specimens. Unfortunately, most of the valuable metallic ores, and even some of the nonmetallic ones, are not transparent; therefore it has been necessary to develop a special technique for the determination of these minerals. Some optical properties-for instance, isotropism, anisotropism, color, cleavage, reflecting power-are often adequate in roughly classifying the mineral. Only "reflecting power" is a measurable value, provided special photometric equipment (ocular photometer or Orcel's photoelectric cell) is available. The other optical properties mentioned are more or less relative,

Jan 1, 1942

FRank FirmstoNe, Easton, Pa.: The effect of lead on brass seems to have been recognized by Berthier, and the facts published by him as early as 1818 (Ann. des Mines, 1st ser., iii., 1818, p. 347 et seq.). He there says expressly that copper containing lead makes " dry " (see) brass, and that, for the same reason, blast-furnace

Jan 1, 1898

By D. K. Deardorff, Earl T. Hayes

An improved technique is described for the accurate determination of melting points of metals in the temperature range 1500' to 2500°C. The improvements consist of gradient heating and refinements in cavity preparation to obtain true black-body conditions. The melting point of hafnium, as determined by this method, is set at 2222°±30°C. This is over 200°C higher than one of the values reported earlier. Discrepancies in the previously reported values for the melting point of hafnium are explained. The melting points of zirconium and titanium are found to be 1855O±15OC and 1668°±10°C, respectively. Reproducibility of results was ±3OC. PRIMARILY, this report is being made to correct a 1975o±25oC1 value for the melting point of hafnium, and to present an improved method for melting point determination. As a matter of interest, the technique was also applied to determining the melting point of zirconium and titanium. There is a wide difference in the melting point of hafnium as reported by competent investigators. DeBoer and Fast' reported a value of 2230°±500C, and later work of McPherson, as reported by Aden-stedt, placed the melting point at 1975o±25oC. Zwikker" calculated that the melting point was 2430°C. In resolving this discrepancy, improvements were made in the procedure for determining the melting points of refractory metals in the range 1500" to 2500°C. Special techniques are necessary to determine the melting point of these metals accurately. Since the metals oxidize in air above 900oC, the determinations must be carried out in an inert gas or vacuum. Also, every known refractory contaminates them to some extent. In addition, the attainment of true black-body conditions is always difficult. DeBoer and Fast actually determined the melting point of Hf-Zr as-deposited iodide process alloys and extrapolated to 100 pet Hf. McPherson employed a tungsten wire suspension similar to that described by Schramm, Gordon, and Kaufmann,1 and used hafnium metal produced by the iodide process. There was no apparent reason for the wide spread in melting points, since the quality of the metal was very good and the work was under the direction of highly competent investigators. Retracing some of this work revealed one understandable error in the case of hafnium, and led to development of an improved technique for determining melting points of reactive metals in the range 1500" to 2500°C. Material Crystal bar hafnium, zirconium, and titanium were used for this work, with analyses as shown in Table I. The hafnium was of the highest purity that has been prepared, though not as pure as the zirconium and titanium. At the instigation of the Pittsburgh Area Office of the AEC, a special lot of Hfo2 was purified, converted to the tetraflouride, and bomb-reduced with calcium, all at the Iowa State College Laboratories. This crude hafnium metal was then refined by the iodide process at the Foote Mineral Co. All specimens were cut with a Sic wheel, ground, pickled, and dried carefully before use. Procedure General Tungsten Suspension Method—In this method, a small specimen is suspended by a fine tungsten wire in a slender, induction-heated tungsten or tantalum cylinder, all under vacuum. The melting point is determined by heating the specimen slowly while observing it with an optical pyrometer focused upon a portion of the specimen that radiates as a black body. This means that there should be no reflected radiation, either from colder objects near the pyrometer or from hotter surfaces. The induction heater would be the only hotter object and, if it is slender enough, the specimen will attain the same temperature. Often a slender hole is drilled into the specimen as a source of black-body radiation. This was the general method used by McPherson in obtaining his value of 1975°C for the melting point of hafnium. In trying to repeat this work, it was found that the points of contact between the

Jan 1, 1957

By Paul Berggreen

LIST OF PUBLICATIONS In the Bibliography titles of publications are replaced by corresponding symbols in this list. American A-1. Transactions of the American Institute of Mining Engineers, New York. A-2. Journal of the New York Microscopical Society, New York. A-3. Journal of the Franklin Institute, Philadelphia, Pa. A-4. The Metallographist, Boston, Mass. A-5. The Electrochemical and Metallurgical Industry, New York. A-6. Bulletin of the American Institute of Mining Engineers, New York. A-7. The Iron Trade Review, Cleveland, Ohio. A-8. The Journal of Physical Chemistry, Ithaca, N. Y. A-9. The Physical Review, New York. A-10. Van Nostrand's Electric Engineering Magazine, New York. English E-1. Proceedings of the Institution of Mechanical Engineers, London. E-2. Journal of the Iron and Steel Institute, London. E3. Proceedings of the Institution of Civil Engineers, London. E-4. Journal of the Chemical Society of London, London. E-5. Philosophical Magazine, London. E-6. Proceedings of the Royal Society of Edinburgh, Edinburgh., E7. Carnegie Scholarship Memoirs, London. E-8. Proceedings of the Royal Society of London, London. E-9. Chemical News, London. E-10. Philosophical Transactions of the Royal Society of London,, London. E-11. Transactions of the North-East Coast Institution of Engineers and Shipbuilders, Newcastle-on-Tyne E-12. Iron, London. E-13. Nature, London. E14. English Mechanic and World of Science, London.

Jan 6, 1914

By F. S. Norcross

DEVELOPMENT of the manganese deposits of Cuba is a matter of importance not only to those involved in this industry on the Island but to the United States steel industry and to our Nation as a whole. For years our domestic resources of manganese have been wholly inadequate, but the recent Cuban development points the way toward solution of this strategic mineral problem.

Jan 1, 1939

By D. S. Tomalin, D. F. Stein

The effect of reducing oxygen to low concentrations on the fracture of high-purity iron single crystals has been examined at 78° and 20°K. It is found that iron single crystals grown by the strain-anneal method usually contain a few occluded grain boundaries which may become embittled in the presence of oxygen, thereby nucleating cleavage fractures. High purity with respect to interstitial elements was found to inhibit twinning and evidence is presented for an orientation dependence of the resolved yield stress. Deformation occurred by slip rather than twinning at both temperatures of testing with elongations of as much as 9 pct at 20°K. THE fracture properties of iron single crystals have been observedl-3 to be a function of temperature, orientation, and purity. Allen, Hopkins, and McLennan1 demonstrated that at 78°K iron single crystals became increasingly brittle as the tensile axis approached the (001) pole of the stereographic unit triangle. Iron crystals with the tension axis near a (001) pole were completely brittle and orientations near the (011)-(111) boundary were very ductile, achieving a 100 pct reduction in area prior to fracture. Later work of Biggs and pratt2 and of Edmondson3 demonstrated that by reducing the carbon content of the single crystals the transition between brittle and ductile failure at 78°K could be shifted to orientations nearer the (001) pole. Ed-mondson went further and pointed out that any mechanism which tended to increase the yield strength of the iron (i.e., carbon addition, pre-strain) also increased the tendency for brittle behavior at 78°K. Thus by a reduction of carbon content Biggs and Pratt were able to obtain ductile behavior to within 20 deg of the (001) pole, and Ed-mondson was able to obtain ductile behavior to within 26 deg of the (001) pole. Edmondson's material had a total interstitial content (carbon, oxygen, and nitrogen) of approximately 60 ppm and, although Biggs and Pratt reported no analysis, indications were that their iron contained comparable impurities. Stein, Low, and seybolt4 purified iron single crystals to a total carbon, oxygen, and nitrogen content of approximately 20 ppm. They observed a lowering of the yield stress with this increased purity, and thus one might have expected an observation of increased ductility. Although they tested specimens of orientations which the previous workers had indicated should be ductile, the crystals failed at a 78°K in a brittle manner with little elongation. Stein noted,' however, that about 90 pet of the failures could be traced in origin to occluded grains. Allen et al.1 and Edmondson3 do not report examination of their cleavage surfaces, but Biggs and pratt2 reported that microscopic examination of the cleavage surfaces of many of their specimens revealed the presence of small occluded grains. Honda and cohen6 and Keh7 have also observed the initiation of fracture at occluded grains in iron single crystals. Therefore, the additional complication of occluded grains must be considered in studying the properties of iron single crystals and the origin of fractures determined if the ductility exhibited by the crystals is to be considered meaningful. Various investigators8-12 have studied the effects of impurities on grain boundaries in high-purity polycrystalline iron. Rees and Hopkins10 showed that the addition of oxygen to low-carbon (0.002 pet) iron weakened the grain boundaries, causing a shift from transcrystalline to intercrystalline fracture and a progressive decrease on the brittle-fracture stress with increasing oxygen content. In addition, it has been shown by Low and Feustel11 that the addition of carbon to polycrystalline iron containing oxygen eliminated grain boundary brittleness. Thus, oxygen can embrittle grain boundaries in high-purity polycrystalline iron, but the addition of an appropriate amount of carbon can eliminate the oxygen-induced brittleness. The oxygen content (19 ppm) of the iron "single crystals" employed by Stein el al. was large enough to suspect impurity effects at the occluded grain boundaries. Allen et al.1 Biggs and pratt,2 and Edmondson3 may have masked any occluded grain problem in their specimens considering the relatively high carbon levels they employed. stein13 demonstrated that the addition of as little as 0.9 ppm C to previously purified (less than 5 x 10-3 ppm C) "single crystals" would increase the elongation from a few percent to more than 20 pet at 78°K and the fracture was not associated with grade boundary initiation.

Jan 1, 1965

By H. C. Howard

Reaction of oxygen and bituminous coal starts as soon as the coal bed is exposed to air and, with some coals, proceeds with significant velocity even at normal temperatures and at normal oxygen partial pressures of one-fifth of an atmosphere. At higher temperatures, the reaction is greatly accelerated and ultimately a condition is reached where the process is very rapid and we then speak of combustion. It is the purpose of the present paper to discuss the reactions of oxygen and coal at temperatures below those of active combustion. It is these low temperature oxidation reactions which are responsible for heating in storage and for marked changes in agglutinating proper-ties. These reactions may also be employed for the preparation of organic acids, which are of direct interest to the chemical industry. For convenience in discussion, the low temperature reactions of oxygen and bituminous coal can be roughly divided into three stages though there is, of course, overlapping. Stage I is a surface oxidation stage, characterized by the addition of oxygen, with the formation of oxygen containing groups some of which have acidic properties. Carbon dioxide, carbon monoxide and water may be formed con-comitantly and are always liberated at higher temperatures, and in cases where the oxidation is prolonged. Superficially, the coal is little affected by this primary stage of oxidation and usually only minor changes in ultimate composition result. There may be definite changes in coking and coking properties, and heat of combustion susceptibility to further oxidation. The presence of acidic groups can be demonstrated by specific reactions. These groups may show cation exchange properties like the mineral zeolites. The formation of oxalic acid has been reported. If the oxidation is continued, a large fraction of the organic material of the coal is converted ultimately into alkali soluble, acid insoluble products, which have been given the name "regenerated humic acids" and which are the characteristic products of Stage 2. These humic acids, in the solid stage, do not differ greatly in appearance from the original coal, but show large differences in chemical composition and chemical and physical properties. Along with the humic acids, carbon dioxide and some of the water soluble types of Stage 3, are also formed. If the oxidation is carried still further, the humic acids may be degraded completely to the simpler, lower molecular weight acids of Stage 3 which are characterized by solubility in acid as well as in alkaline media, and by their orange, yellow or white colors. Additional carbon dioxide is formed in the transformation from Stage 2 to Stage 3 and, for a number of American coals, a maximum yield of the water soluble types of acids is reached when about 50 pct of the carbon of the coal is converted to carbon dioxide. Primary Oxidation The initial step in the reaction of gaseous oxygen on coal, like that on carbon,

Jan 1, 1949

By A. Satter

Studies of wellbore heat transtnission during the injection of a hot fluid, as either gas or liquid, have appeared in he literature. The present investigation takes into account the effect of condensation, which is of practical sig-nificance when considering steam injection operations. Calculation procedures are given for superheated and for saturated and undersaturated steam. Effects of injection rate, time, pressure, temperature and depth of a well on heat losses have been analyzed. The benefits of using a packer are discussed. Also presented are correlations for estimating heat losses involved during injection of saturated steam. INTRODUCTION Studies of wellbore heat losses during the injection of a hot fluid have appeared in the literature. Ramey' has presented a useful solution for calculating temperature of a heated gas as a function of depth and injection time. Ramey and others have also presented solutions for the hot liquid case.'. ' No method is available to take into account the effect of condensation, which is of practical significance when considering steam injection operations. This paper presents a method of estimating the quality of a condensing fluid as a function of depth and time. The approach is basically the same as that used by Ramey. The following injected fluids and conditions are considered in this study: 1. Injection of superheated steam A. Decrease in temperature until cooled to the saturated state B. Condensation until condensed completely into hot (saturated) water 2. Injection of saturated or undersaturated steam; condensation until condensed completely into hot (saturated) water. Although this investigation does not include cooling of water after steam is completely condensed, Ramey's solution for the hot liquid case can be used for this purpose. The effects of various process variables on heat losses During the injection of steam into a well are investigated. THEORY QUALITY OF CONDENSING STEAM Predicting the behavior of condensing steam flowing down the injection wellbore requires an estimate of the quality of steam, i.e., the mass fraction of vapor in the mixture. Let us divide the total depth of the injection well into several segments which might be, but do not have to be, of equal magnitude. Consider condensation within a given depth interval AZ, the bottom of which is located at a depth Z from the surface (Fig 1). The following equation, derived in the Appendix- relates the quality of steam at the bottom of an interval to that at the top of the interval:

Jan 1, 1966

By George Boulter

Draglines 8.2-1 Introduction. The nature and characteristics of rock and rock derivatives forming the crust of the earth vary so greatly from place to place that it is impossible to use the same numerical factors to show the, productive ability of excavating equipment on different jobs or projects. Factors for each project must be developed individually and applied as the conditions and requirements dictate. TYPES' OF DRAGLINES. Types of draglines are differentiated by the propelling method used and are generally divided into four classes, as follows: 1. Wagon mounted 3. Crawler mounted 2. Truck mounted 4. Walking Figure 8.2-1 shows a truck-mounted dragline. This type is considered to be the most mobile unit. In order to increase stability over the side, outriggers are installed as part of the truck chassis. This feature is not shown in .this figure. Figure 8.2-2 shows a crawler-mounted dragline. The long, wide crawlers are used to increase the stability and reduce the bearing pressure of this unit. These features allow for use of these units on surfaces too soft for the wagon- or truck-mounted types. Figure 8.2-3 shows a walking-type dragline. The large diameter tub and the well-supported boom through the gantry gives high stability for rugged works over a long life. BASIC PARTS OF A DRAGLINE. The basic parts of a dragline are illustrated in Fig. 8.2-4. A deck layout is shown in Fig. 8.2-5 with the main components named. OPERATION OF A DRAGLINE. Following is a description of the steps and controls present in a typical cycle of operation of a large dragline having independent hoist and drag motors. Starting the cycle with positioning the bucket on the ground under the point of the boom, the next step is

Jan 1, 1968

By David R. Mitchell, R. M. Fleming

MANY trends were evident in the coal industry during 1951. Some were favorable for the industry; others were not. Probably those having the most far-reaching consequences are those affecting coal's markets. The rapid dieselization of many railroads and the continued trend toward oil and natural gas for home heating has caused serious dislocations in various mining districts. Mines have been forced to close down or to work on a reduced time basis. Conversely the increased activity in the metallurgical industries has increased the demand for coking and special purpose coals, and the growing production of electric energy has increased the demand in certain areas for steam coals. The increased demand for metallurgical coal and for steam raising by the large utilities is more than equal tonnage-wise to the loss of coal to railroad dieselization and conversions to oil and gas in the domestic market. Since much of the expansion is at captive mines of large corporations, many commercial operators supplying railroad and domestic users have had their markets curtailed without any compensating demand from other sources. Feverish activity was in evidence in many areas by commercial operators attempting to find new markets. The Norfolk and Western Railway is the, only major American railroad committed to the burning of coal. It has an exceptionally good cost record. During 1951, fifteen additional modern coal-burning steam switching locomotives were authorized for construction in the company's Roanoke shops at a cost of about $1,450,000. When the new order is completed the road will own a total of sixty locomotives of the modern-switcher type, including thirty acquired by purchase last year. The Norfolk and Western today is the only American railroad building its own motive power. All of these locomotives burn coal. Production Coal production in the year 1951 will approximate 570 million tons of anthracite, bituminous coal, and lignite. Of this, approximately 7 pet is anthracite. Total production is approximately 30 million tons more than in 1950 and reflects the increase in general industrial activity. Exports are expected to be close to 50 million tons. The industrial stockpile is close to 75 million tons, the highest it has been since 1943. With the exception of the usual local stoppages the year 1951 was unmarked by labor disputes. It was a year of good labor-management relations with a negotiated wage increase unmarred by a work stoppage. This may be the beginning. of an era of sensible negotiations to find agreeable settlements of disputes without the usual protracted bickering and industry-wide strike. The United Mine Workers of America has condemned wildcat strikes, stating that in nearly every, instance proper grievance procedures have not been instituted. Government defense organizations, perhaps profiting by their experiences during World War II, are pursuing a more enlightened program with regard to the fuel requirements of the nation. Many prominent officials have stated that wherever possible coal should be considered the primary source of fuel in all defense expansion. With the increased consumption of steel by defense projects, approval of transportation facilities for liquid and gaseous fuels have been refused where these fuels would enter a coal producing area. Liquid and gaseous fuel producers also have failed to provide satisfactory evidence that they have sufficient reserves and are capable of supplying their product in adequate amounts for the periods of time required. Realization has at last become prevalent that the hydro-electric power installations in several areas are insufficient to handle increased demands.' Steam generating plants are being constructed in these areas and equipped to burn coal. Most notable of these, is the TWA area whose supplemental steam power plants are expected to consume 10 million tons of coal per year when completed. The Pacific Northwest is another area which is expected to follow the same pattern. Nearly all new steam-power generating plants are being equipped to burn coal either as a primary fuel or as an emergency measure. Metallurgical Coal The steel and other metallurgical industries are expanding rapidly to meet increased industrial demands and defense orders. Since these industries are dependent on coke, coke has had a year of high production and can be expected to break all existing records when steel-plant expansions are completed. Most notable of the expansion projects is that of the Delaware River area where the iron ore will be received by ship from Canada and South America. U. S. Steel is only one of several steel corporations that are planning on putting integrated steel producing units in this area. The Defense Solids Fuels Administration announced in December that through. November 30, 1951. 29 projects in eight states, with a total cost of

Jan 1, 1952

By Wllliam D. Davis

C OMMERCIAL production of oil in northeastern Oklahoma began in 1897 and in the next two decades this area became one of the greatest oil districts of the time. Its importance is now secondary, but thousands of wells in this area have produced uninterruptedly for more than thirty years. They are now classified as stripper wells. By means of what is known as water flooding their L. production can be considerably in- creased. This practice consists in injecting water under pressure into the sand surrounding an oil well, thus displacing the oil in the pores of the sand and forcing it into the oil well.

Jan 1, 1940

By Hans Lundberg, Basil T. Wilson, H. Steuart Scott

FOR the benefit of those readers who may not be in close touch with present practices in the geophysical prospecting for ore, brief reference will fiat be made to the advantages and shortcomings of the methods to be discussed. Magnetic and electric methods are generally accepted as the most useful for ore prospecting. By magnetic methods, magnetic intensities that are not normal may be recorded and outlined. From these can he located concentrations of such highly magnetic minerals as magnetite or pyrrhotite, which sometimes occur in such large masses that they are of economic value in themselves. More often. however, these magnetic min¬erals are associated with others, such as copper, zinc, lead, gold, and silver, which, if existing in sufficient concentration and quantity, may constitute valuable ore bodies. It is therefore only when pyrrhotite and magnetite are present in these bodies that the magnetic method can be used to indicate their presence.

Jan 1, 1945