Search Documents

By I. H. Van Horn

IN the development of the incandescent electric lamp one aim of the investigators has been to establish the fundamentals of lamp design, so that the performance of any new lamp may be accurately predicted. The study of the temperature relations in lamps has done much toward establishing these fundamentals. Fig. 1 gives the typical FIG. 1.-ARRANGEMENT OF PARTS IN MAZDA B AND MAZDA C LAMPS. arrangement of the lamp parts in both the Mazda B (vacuum) and Mazda C (gas-filled) lamps. The outstanding differences are the filament form and the bulb shape. The ideal lamp is one in which the filament operates at a uniform temperature throughout its length. In practice, it is necessary to disturb this uniformity by the introduction of supports and terminals. The amount of cooling at the supports and terminals affects the over-all efficiency of the filament as a light producer. The life of the lamp is ordinarily proportional to the maximum and not to the average filament temperature. The Holborn-Kurlbaum type of optical pyrometer has

Jan 9, 1919

By J. C. Martin

Equations for three-phase, three-dimensional, compressible flow (including capillarity) are reduced to two-dimensional relations by a partial integration. This reduction allows three-dimensional flow problems to be treated with mathematics for only two spatial dimensions. The results can be used to formulate flow equations for two-dimensional reservoir simulators in which the effects of capillarity and fluid segregation in the third dimension are represented. Such reservoir simulators would retain many of the aduantages of two-dimensional simulators while simulating three-dimensional effects. The principal restriction of the method is that the thickness of the reservoir should be small, compared to the distance across the reservoir. INTRODUCTION In recent years, computers have been used to calculate the performances of many reservoirs. Most of the detailed calculations, however, are based on finite difference solutions of the flow equations, and present day computers are seldom able to handle a sufficient number of cells to produce entirely satisfactory solutions, even for reservoirs represented by two-dimensional arrays of cells. The situation becomes much worse when one wishes to approximate the reservoir by a three-dimensional array. A great saving in computation or a more detailed solution can be obtained for many reservoirs by using the partial integration of the equations of flow presented in this paper. The integration reduces the three-dimensional equations to two-dimensional relations; and, for studies of two-dimensional flows in vertical cross-sections, the equations are reduced to one-dimensional relations. Most reservoir performance calculations currently are based on one- or two-dimensional flow re1ations.l-3 In some cases flow in the third dimension is approximated by assuming a particular type of vertical saturation distribution, such as gravity segregation.l.2. The relations developed in this paper approach those for segregated flow as the capillary pressures approach zero, and they approach those for uniformly distributed saturations as the capillary pressures are increased. For this analysis, the ratio of the reservoir's thickness to the maximum distance across it must be small. The capillary pressures between the oil and water should also be small compared to the maximum pressure difference in the reservoir. This requirement is met by most reservoirs. It is assumed that the capillary-pressure curves are well defined, whether or not hysteresis effects are included. Also, the reservoir must have sufficient vertical permeability to allow the fluids to segregate. The results presented here provide a firm theoretical foundation to Coats' et aL5 assumption of vertical equilibrium and extend the relations to three-phase flow. Coats' assumption of vertical equilibrium, which he verified by calculations and experiment, is developed here mathematically from basic flow equations. DISCUSSION SATURATION AND PRESSURE DISTRIBUTIONS Appendix A presents a mathematical analysis of fluid flow in reservoirs where the ratio of thickness to maximum distance across the reservoir is small. The results indicate: (1) that the fluids along any line perpendicular to such a reservoir's upper surface are in static capillary equilibrium (vertical equilibrium); (2) that, to a first approximation, the fluid pressures and properties are functions of only areal position in the reservoir and time; and (3) that hydrostatic pressure gradients exist along any line perpendicular to the reservoir's upper surface. The results might be expected after studying several physical considerations. First, no flow is allowed normal to the upper and lower reservoir boundaries, which are relatively close together.

Jan 1, 1969

By Hugh S. Spence

IN MAY, 1930, G. LaBine and E. C. St. Paul, prospect¬ing round the southeastern shore of Great Bear Lake, in the North West Territories of Canada, discovered pitchblende at what is now LaBine Point. At the same time, they also found native silver in a small sheared break on an island lying off the point. Late in 1930, samples of the pitchblende were sent to the Mines Branch, at Ottawa. The material consisted of several fair-sized slabs of botryoidal pitchblende banded with a brownish quartz. A small amount of chalcopyrite was visible as small particles and fine veinlets, and the pieces were rather heavily stained a yellowish-green by secondary copper-uranium salts. Analyses were run in the Mines Branch Ore Dressing Laboratories on two samples, and small-scale concentration tests were made on one of them. The results of this work were published in a Memorandum Series report (No. 48) of the Mines Branch, in March, 1931.

Jan 1, 1932

By H. A. Domian, H. Biloni, G. F. Bolling

Jan 1, 1965

Jan 1, 1968

By John T. Norton

N order to attempt to arrive at a better under-Jl standing of the whole basic problem of sintering, these remarks will serve as an introduction for discussion that is included and will, perhaps, help to isolate specific questions which need to be answered or to suggest some definite avenues of investigation which should be followed. To bring some sort of logical order into the presentation, I will consider the various types of interaction between the metal to be sintered and the atmosphere which surrounds it, depending upon whether the phenomena are essentially chemical or physical in nature. For example, when the only necessary criterion for the satisfactory sintering of a certain powder is the removal of an oxide skin, then the problem of choosing a suitable atmosphere is primarily chemical; however, if a special surface condition as a consequence of the oxide skin removal is necessary for particularly effective sintering, then the problem becomes a physical one. Of course, the two aspects overlap considerably, but it may be possible to make a distinction in principle if not in practice. The chemical characteristics of the phenomena will be emphasized, since these are the better known. Metal-gas reactions involved in sintering are controlled primarily by the thermodynamics of the processes involved. In which direction will a reaction go and how far before it stops? The answer is to be found in the magnitude of the free energy change associated with the reaction. If a constituent is to be removed from the specimen as completely as possible or if a constituent is to be formed in the specimen as completely as possible, then one chooses conditions which are far from equilibrium so that the reaction is driven toward completion. On the other hand, if the composition is to be maintained at a desired value, then conditions are adjusted as closely as possible to the equilibrium point. This aspect of the problem is susceptible to quite precise analysis, provided, of course, that the significant reactions can be recognized and the required thermodynamic data are available. Conversely, if one asks how fast the reaction goes or how far it proceeds in a given time, the answer is frequently much more difficult to answer in quantitative terms. Yet the rate-con trolling factors of the reactions may be of primary importance in the success of a particular operation, especially where competing processes are at work. Both equilibrium and rate factors must be understood if a clear picture is to be obtained. For instance, in a process for carburizing titanium dioxide, is the difficulty of obtaining a stoichiometric Tic due to a true limitation of the equilibrium or simply to a very slow rate of reaction? An example of this appears in the work of Kalish and Mazza.' They showed that the oxygen content of sintered iron compacts was lower when sintered in pure hydrogen than in the case where the hydrogen was diluted with either argon or nitrogen. The equilibrium oxygen content of the iron would be the same in the two cases, since it is determined by the ratio of the partial pressures of water vapor and hydrogen and this pressure ratio is unchanged by dilution. The rate of oxygen removal, however, under the conditions of a constantly replaced furnace atmosphere, depends upon diffusion and thus upon the concentration of hydrogen in the furnace atmosphere. Possibly the clearest way to illustrate the interplay of these two factors is to consider in more detail some of the typical metal-gas reactions. Adsorbed Gases It is common experience that fine metal powders with their very large surface areas often contain large quantities of gas. This gas, which results from exposure to air or perhaps from some step in the

Jan 1, 1957

By Daniel T. Brian, O&apos

Exploration targets and results in the mining industry are commonly summarized in terms of tonnage and grade. Business appraisals require, as additional information, the expected profit or loss implied by the physical summay. The early incorporation of knowledge gained through financial analysis computations can provide a means for economically resolving many common exploration and development problems. Examples of such applications from the activities of exploration planning, reconnaissance, land acquisition, and development planning are presented. While prospecting for mineral deposits, geologists are frequently asked what they hope to find or have found. The response is usually descriptive, such as "50 million tons of 1% copper," and the economic implications are deferred until a capital investment decision is required. At that time, a financial analysis integrating the four analysis components is completed. These components are: 1) Tonnage and Average grade above cutoff grade 2) Capital and operating costs 3) Product value 4) Appropriate profit or loss accounting Close examination of these components reveals that there is no intrinsic reason for avoiding financial analyses at earlier stages in exploration, as long as the uncertainty of the estimate is realized. Tonnage and average grades are commonly estimated at early stages in exploration. For this component, the appropriate cutoff is the major uncertainty. Capital and operating costs are difficult to estimate before detailed quantitative information is available, but estimates useful for the types of applications pertinent to earlier exploration stages are possible. Product value estimates may or may not be difficult, depending on the pricing structure of the particular commodity. A simplified accounting procedure usually may be adopted without introducing any significant loss of validity. This paper describe some of the financial analysis applications which are pertinent during mineral exploration and deposit development. These applications lend additional insight during exploration planning, land acquisition, physical exploration, and development. The examples are oriented toward a hypothetical management investment policy which is based on a single criterion, a minimum 15% discounted cash flow rate of return. In reality, managements use multiple criteria. This simplification is convenient for purposes of presentation and does not invalidate the examples. Computers are useful, but not a requirement, for the applications described. The use of computers provides the results on a more timely basis at costs lower than equivalent manual computations. UNDERLYING PRINCIPLES AND ANALYSIS METHODS Data estimates are subject to uncertainty. The analyst may choose to assess this uncertainty by using one of two principles. Each principle has some advantages. The principle most commonly employed is "assumed certainty." Each financial analysis is based on one set of selected data, which may represent the average estimates, minimum expected conditions, etc. The critical data is identified by making successive calculations, varying the values used. Such studies, called sensitivity analyses, isolate the economic effect of various uncertainties, and guide the allocation of future efforts toward improving the overall accuracy of the analysis. A second principle, "assumed risk," examines the interactive effect of the current uncertainties by qualitatively assigning probability distributions to each data element. These probability distributions indicate the currently appraised chance that a given numerical value will prove to be true. The corresponding procedure, risk analysis, consists of processing many individual financial analyses, each analysis being based on randomly selected numerical values from the probabilistic distributions. The result is a numerical presentation of the uncertainty, but care must be exercised in the interpretation of results. The advantage of this procedure is the direct measurement of economic uncertainty caused by the interaction of uncertain estimates. Kennecott Copper Corp. has developed computer systems for accomplishing sensitivity and risk analyses.

Jan 1, 1970

By J. B. Cheatham, M. D. Biggs

This paper presents a systematic method for determining the forces on a simplified roller bit. The kinematics of an actual roller bit drilling in rock is complex; nevertheless, it is desirable to obtain an accurate analytical model.. As a preliminary study, the roller bit is represented here by a simple two-dimensional bit and the rock by a Coulomb plastic material. Results from previous work, plus additional assumptions, are incorporated into a computer program to determine the forces required to move the bit in a specified manner. Example problems are worked by use of this program. By studying similar drilling problems and by supporting laboratory work, one could eventually obtain an accurate analytical model for drilling by an actual roller bit. This could lead to the compilation of a catalog of results that, in turn, would allow selection of the optimum drill bit for any given situation. INTRODUCTION

Jan 1, 1970

By C. E. Sims

THE following presentation is more a summation of observations made and conclusions drawn over a period of three to four years than a report of experiments made with a definite objective. Tests were made, of course, to verify hypotheses, but the large mass of data was collected incidental to other work. Lack of space forbids the presentation of more than a few of those data. On the other hand, it is unfortunate that some of the most illustrative examples are not available. The work is admit¬tedly incomplete but is presented in the hope that it will stimulate further work along a similar line. The answers to many of the questions left unanswered by this paper will be found only after long and painstaking study, such as is scarcely possible in a commercial laboratory where problems of immediate importance consume most of the time. It is also hoped that this study will in some measure throw light on some of the dark spots of steelmaking, and help to clarify some of the annoyingly vague references to "good practice." Only cast steel was studied and the conclusions apply to cast steel, but it is the authors' opinion that the quality of rolled or forged steel is largely dependent on the quality of the ingot, which is a casting. Although this discussion deals almost entirely with inclusions, it is important that the reader understand that only those natural inclusions which owe their origin to the solubility of certain materials in steel and to the chemical reactions of steelmaking are considered. Accidental inclusions, such as entrapped particles of slag, nozzle, runner, or mold are outside its province and are not considered. Such accidental inclusions are always dangerous and should be carefully avoided.

Jan 1, 1932

By L. E. Fish, G. S. Wyman

CHUQUICAMATA open-pit mine is capable of producing a total of 105,000 tons daily. When the sulphide plant is operating to capacity the distribution of this quantity will be approximately 30,000 tons sulphide ore, 30,000 tons oxide ore and 45,000 tons of waste. At that time the combined capacity of the oxide and sulphide plants will be about 540 million lb of copper per year. Twenty one benches have been opened to date and all are still active except the three top ones at the northeastern limit of the pit. These have been pushed back to final slope line. The pit is 8850 ft long, 3540 ft wide and 980 ft deep. Benches are not all developed to a standard height as the large development shovels used in cutting new benches have been of different size and range. At this time new benches 521 ft high are being developed with an' 11-yd shovel. Ore haulage through the greater part of the pit operation has been on down grades to the crushing plant. With the opening of bench F-4 in April 1944 the first adverse-grade ore haul was encountered. Of the total tonnage now being mined, 35 pct comes from the four benches that are below the level of the crushing plant yard. Waste had been dumped on the same or nearly the same level as the bench from which it was removed up to the opening of bench F-4. Waste from this and lower levels is hauled to the level of the crusher, yard where it must cross the flow of ore traffic to reach the only available dumping space to the east of the mine. The average ore haul is 3.13 miles one way shovel to crusher, and the average waste haul from that portion handled by railroad is 3.32 miles one way from shovel to waste dump. Waste that is being removed by truck haulage from the upper part of the -mine is hauled an average of 1 mile. Ore loaded by trucks is hauled 3/4 mile to a car loading ramp and then by rail to the crushing plant. Drilling and Blasting There are two types of development for blasting being used: One for opening new benches and the other for bank shooting. The former consists of 9a in. diam churn-drill holes drilled 11.8 ft center to center in rows 10.2 ft apart with the holes staggered in the rows thus giving an equilateral-triangle pattern of 11.8 ft on a side. After the first block, 492 ft long by 71.5 ft wide, is shot in the pattern described above, the cut is advanced by smaller shots consisting of four rows of holes spaced 23 ft center to center with the rows 23 ft apart. These shots are fired in conjunction with side shots in which the holes are drilled 33 ft center to center and 29.5 ft back from the toe, thus squaring up the bank for subsequent shooting. An average bank shot consists of about 60 holes drilled in two rows parallel to the face, 30 holes to

Jan 1, 1952

By B. H. Caudle, L. G. Loncarie

Pilot flooding is one method of evaluating a proposed secondary recovery project. However, the amount and rate of oil recovery from an unconfined pilot area is not usually the same as from an equal area in a large-scale flood. This is true because fluids are free to move across the boundary of a pilot area. The result is that some of the oil produced in a pilot flood may come from outside the designated area and some of the displaced oil may leave the pilot area completely. This paper presents the results of fluid-flow model studies on a five-spot pilot flood. Mobility ratios between 0.1 and to have been studied. The effects of changing the ratio of injection to withdrawal rates are shown. INTRODUCTION A small-scale field test, or pilot flood, is an accepted method for evaluating the applicability of a secondary recovery operation and the economic potential of that operation for a reservoir. The pilot flood is carried on in the same manner, with the same injected materials and at the same pressures as would be used were the secondary recovery program to be expanded to a larger area of the field or to the entire field. If the reservoir fluid and reservoir rock properties are the same in the pilot area as in the rest of the reservoir, the production, injection and other pertinent data associated with the pilot test will represent and measure what should be expected from a full-scale development of this secondary recovery program. There is one major exception which, unfortunately, has been overlooked by many and which has been awaiting quantitative definition. This is the sweep-out pattern the reservoir engineer must use in interpreting the pilot flood and in extrapolating it to the full-scale development. The sweep-out area in a pilot flood is not contained within the five-spot pattern. Further, there is oil flow into and/or out of the five-spot during a pilot test. Thus, production data from pilots must be interpreted with this different flow system and sweep pattern in mind. We have studied the sweep-out pattern that will exist for some conditions of operation of pilot flooding a single five-spot (four injection wells and one producer). In our study, reported here, we have assumed that the reservoir is relatively homogeneous and of uniform thickness in the pilot area. The results of this study en-able the engineer to predict the recovery, injection requirements and project life for a full-scale operation from the pilot flooding data. The effects of various injection to withdrawal-rate ratios and mobility ratios in a relatively gas-free (10 per cent pore volume or less) system are shown. Experimental Method The technique used in this study was the same as that for the X-ray shadowgraph studies of sweep-out pattern efficiencies.' The model of the pilot and surrounding area was made from a uniform packing of round-grain sand consolidated with an epoxy resin. Fig. 1 shows the relation between the model and the pilot area. Only one-eighth of the pilot area had to be represented in the model because we assumed equal injec-

By H. H. Stoek

MINE models have three distinct uses: 1. As exhibits in expositions and museums. 2. As exhibits in law suits. 3. As illustrations in teaching mining engineering. All three uses are in a sense educational. The third, or distinctively teaching function, has not been extensively developed in America as it has been abroad, chiefly because of the cost of the models and the scarcity of model makers. In connection with expositions, such as the Columbian, the Louisiana Purchase, and the Panama-Pacific, a number of very good mine and metallurgical models were prepared with funds furnished by State commissions, by mining organizations or mining companies. At the close of these, expositions, some of these models have been deposited in National or State museums or in educational institutions, but too many of them have been lost, or have been stored, away in some mining company's office or in the basement of some State building, where they have been lost sight of and have gradually fallen to pieces. A visitor to a German mining school is impressed by two facts: 1. The mining laboratories are in general inferior to those in America. 2. The mining museums are infinitely superior -to ours, particularly in models exhibited. One may reply to this comparison by saying that a museum is necessarily a work of time. From the historical standpoint this is, of course, true, but it is not necessarily true in connection with a working museum intended to illustrate current practice. For instance, the oldest mining school in Germany, that at Freiberg, has much excellent historical material, but very little on modern practice, while Berlin, one of the youngest German mining schools, has a most extensive and valuable collection of modern appliances and models. This is true in spite of the fact that one of the best-known model shops is at Freiberg, from which many of, the models to be seen in America have come. Because many of the models in American mining schools have come from

Jan 4, 1917

By W. A. Burns

Vertical flow is an important mechanism in many petroleum reservoirs. Yet no adequate method has heretofore been proposed for determining the in-situ vertical permeability in a reasonable length of time. Core measurements of vertical permeability do not necessarily represent effective in-situ values. Cores may be representative of only localized pockets of high or low permeability, and total reliance on cores might cause one to overlook the presence of vertical fractures altogether. Conventional single-well tests, interference tests, and pulse tests commonly are used to determine horizontal transmissibility, khh/u, but generally are not designed to measure vertical trans-missibility or other groups containing vertical permeability, ku. A new well test described here provides a measure of in-situ vertical permeability as well as the previously measurable horizontal permeability. This "vertical test" determines the vertical diffusivity, kv/gcu, and horizontal transmissibility, khd1/u (where dl is the length of injection or production perforations). The test is basically a short-term interference or pulse test normally lasting less than a day. Conventional down-hole equipment is used between two isolated sets of perforations in the same well, as shown in Fig. 1. A "layer-cake" description of a reservoir can be obtained by running two or more vertical tests in the same well, each over different vertical intervals. Each test can be analyzed for the effective vertical and horizontal properties of the interval tested. In addition, a vertical well test can determine the effective- ness of a shale barrier or tight zone by testing across it. Field use to date of vertical testing has confirmed its utility in reservoir description. Mathematical Basis Interpretation of vertical tests for ku and kh is based on comparison of measured pressure response with computer-generated response. Pressure behavior during a vertical test in a homogeneous, anisotropic, infinite-acting reservoir (infinite in radial extent and bounded in both directions vertically) is given by the diffusion equation for slightly compressible fluids with negligible gravity effects.l A schematic diagram of the problem is presented in Fig. 2, and an analytic solution, based on the image

Jan 1, 1970

By Chung Yu, Wang

CHINA can he roughly divided into three metallogenetic province: North China, the Yangtze Valley, and South China. In North China the old Pre-Cambrian schists and gneisses are represented by the abundance of quartz mines in which sporadic occurrences of copper, lead, zinc, gold, and silver are sometimes found in subordinate quantities. Along the Yangtze Valley and in Central China, extending eastward as far as Shantung, are found here and there intrusions of dioritic rocks, in which occur the famous contact deposits of iron ore, besides which minor quantities of copper. lead, and zinc are also found. In South China the igneous intrunsions are of granitoid type in which, or in the vicinity of which, occur in certain regions immense deposits of antimony, tungsten, tin, and mercury. Broadly speaking. most of the famous coal mines are now situated in regions north of the Yangtze River, in which occur also the sedimentary deposits of iron in contradistinction to the contact deposits of iron along the Yangtze Valley.

Jan 1, 1943

By H. T. Kennedy, S. M. Avasthi

An equation developed for gaseous hydrocarbon mixtures predicts molal volumes with an average absolute deviation of 0.73 percent when applied to 264 natural gas and condensate systems including 2,043 PVT points. Another equation developed for liquid hydrocarbon mixtures predicts molal volumes with an average absolute deviation of 1.12 percent when applied to 346 crude oil systems including 1,759 PVT points. Both equations require composition of the mixture to be expressed as mole fraction of methane through heptanes-plus, hydrogen sulfide, nitrogen and carbon dioxide, together with the characteristics of the heptanes-plus fraction in addition to the temperature and pressure. The equations cover wide ranges of the variables involved, and their accuracy is considerably better than that of other available methods. The equations were differentiated to allow calculation of the coefficients of isothermal compressibility and isobaric thermal expansion. (In this paper the coefficient of isothermal com-pressibility and the coefficient of isobaric thermal expansion will be expressed as compressibility and thermal expansion coefficient, respectively.) Equations to calculate these quantities are presented. INTRODUCTION Calculations of reservoir performance for petroleum reservoirs require accurate knowledge of the volumetric behavior of hydrocarbon mixtures, both liquid and gaseous. Compressibilities are required in transient fluid flow problems, and thermal expansion coefficients are important in thermal methods of production. An accurate laboratory investigation of the PVT behavior of each reservoir fluid encountered would be costly and time consuming. For this reason various correlations for predicting fluid properties have been developed and recorded in recent literature. Correlations have been presented in the form of graphs, tables and equations. Since an increasing number of studies are being conducted with the aid of electronic computers, recent efforts have been directed toward development of correla-tions suitable for computer programming. Application of computers permits the use of more complex correlations which otherwise are not feasible. Moreover, methods for predicting reservoir performance, particularly those based on the compositional material balance, depend upon the capability of accurately expressing the molal volumes and other fluid properties as functions of pressure, temperature and composition. The coefficient of isothermal compressibility c is defined by

Jan 1, 1969

By John Nunes, Frank R. Larson

Temperature-dependent functions of various ten-sile flour stress and fracture parameters were investigated on iron and low composition alloys of Fe-C, Fe-Cr, Fe-Mn, and Fe-Ni. Data were obtained over a range of test temperatures from 200" to -196"C at an initial strain rate of 0.01 min". It was found that the strain-hardening exponent, n, for the Fe-Ni alloys increased significantly at very low testing temperatures with increased alloy addition. Also, the stress and strain at fracture followed a predictable transitional type of behavior. The flour stress-temperature dependence was evaluated employing the relation: M where it is shown that composition can strongly influence the constant M. An empirical formula describing this effect is as follows: M = MI (equivalent at. pct Ni)-'" Some preliminay, tests were run on several commercial steels to test the generality of this relationship. One of the phenomenological explanations of the ductile-to-brittle transition encountered in bcc metals is based upon the difference in the temperature dependence of the flow and fracture stresses.' It states simply that the fracture stress is relatively insensitive to temperature and that the yield or flow stress rises rapidly with decreasing temperature so that, when the flow stress reaches the fracture stress, brittle fracture occurs without appreciable plastic deformation. This behavior is illustrated schematically in Fig. 1 where the ductile-to-brittle transition is shown to occur at two possible temperatures. The lowest temperature, TB, represents essentially completely brittle behavior while the higher temperature, TN, represents "notch" brittle behavior. Support for this theory is obtained when it is observed that fcc metals, which do not commonly have a ductile-to-brittle transition, also do not commonly exhibit any strong temperature de- pendence of the yield stress. This relationship of yield or flow stress behavior with the ductile-to-brittle transition has been generally observed for most metals representative of these two crystallo-graphic structures. One exception to this generalization appears in the case of tantalum where no apparent ductile-to-brittle transition has been observed. However, this may simply be an indication that this type of behavior is not directly related to the flow stress and that some other mechanism such as twinning must also be operative. A comparison of the typical temperature dependence of the yield stress of some representative metals is shown in Fig. 2. In the study of the temperature dependence of the strength of metallic materials, considerable ef-

Jan 1, 1963

By R. E. Morgan, D. L. Douglass

The determination of phase relationships and solid-solubility limits can be performed by quantitative metallography in addition to the usual X-ray and metallographic techniques. For example, Beck and smith1 redetermined the ß/ß + ?, ß + ?/?, a/a + ß and a + ß/ß boundaries in the Cu-Zn system by measuring the volume fraction of second phase of several alloys and extrapolating the volume fraction-composition curves to 0 and 100 pct. A modification of this technique is suggested for certain alloy systems, in which it is not necessary to use several alloy compositions but merely one. A single two-phase alloy may be used to determine terminal solubilities in the following manner. The method consists of equilibrating samples of the alloy in a two-phase region adjacent to the desired solid solution, at three or more temperatures, quenching, measuring the volume fraction of second phase present, and applying an analytical treatment to calculate the unknown solid solution. However, two restrictions are inherent in this technique. They are: 1) only certain types of alloy systems are amenable to it, and 2) the general features of the system must be known. The first drawback to the new technique, i.e., that only certain types of systems may be studied, necessitates that the composition at one end of the tieline must either be constant with temperature or well established as a function of temperature. Either a pure metal or some intermetallic compounds fulfill the former. If it is assumed that the volume per gram-atom of a dilute solution is unchanged by the addition of element B to element A, the composition of the solid solution in equilibrium with the second phase may be determined by a material balance and is given by where X, = volume fraction of B in a solid solution Xc = volume fraction of B in compound c X = volume fraction of B in alloy f = volume fraction of second phase The composition by weight may then be determined by the use of tables in the Metals Handbook2 when the density ratio of the solid solution constituents is known. A possible alternative treatment involving the use of the lever rule is less precise than the above tech- nique. This may be used when the density of the solid solution is either known or may be calculated from X-ray data for several compositions. The following analysis is then made. The ratio of compound to solid solution (by weight) may be expressed as follows: x0 - x wc = xr-x = x0 - x r2i Xc -X where Wc = weight of compound w = weight of solid solution x, - alloy composition, weight percent x = unknown composition Xe = compound composition but where V, = volume of compound VA = volume of solid solution pc = density of compound p, = density of solid solution fc = volume fraction of compound fB = volume fraction of solid solution and fs = l -fc then If pc and xc are known, and f, is measured, then pB is the only unknown on the right side of Eq. [4]. The known densities of the solid solution can be plotted for various compositions and can then be expressed mathematically as a function of composition. The use of an expression of pB = f(x)reduces the equation to one unknown—the desired solubility. In the event that the densities are unknown, they may be calculated for various compositions from Vegard&apos;s law. The calculated values are then plotted and expressed analytically. The most accurate results are obtained for Eq. [4] when fc<< 1, i.c., when (x, -x,) - 0, &/l-f, - m; but as fc/l -fc - 0, (xl-x,)- (x, - x), and x - x,,. However, the accuracy with which fc can be measured decreases as f, decreases.3 Alloys for investigation must be selected by a compromise, which is based upon an error analysis of Eq. [4] and knowledge of the accuracy of volume fraction measurements. An examination of phase diagrams in the literature showed many which were amenable to the technique described here. The zirconium-copper system was selected in order to determine the solubility of copper in beta zirconium. Pieces of an alloy which was arc-melted three times were wrapped in tantalum foil and sealed under an argon atmosphere in Vycor tubes. The sealed samples were equilibrated at temperatures from 850" to 960°C for 3 weeks and quenched to room temperature by smashing the capsule in water. Several planes of polish were examined, and

Jan 1, 1960

By Y. C. Liu

Both the habit plane of martensite and the orientation relationship between the matrix and martensite platelets of different habit planes have been investigated in binary titanium alloys with molybdenum, chromium, and iron. The effect of the mode of deformation on the martensite habit plane was studied. A micrograph of an exposed mar-tensite platelet is presented. IN the study of martensitic transformation in Ti-Mn alloys,&apos; two martensite habit planes—{334), and {344)8—were reported. The {334), habit was also observed in unalloyed titanium upon transformation,&apos; although there is disagreement with respect to the exact indices. The other habit plane, {344),, has not been reported in martensitic transformation in any other alloys. The present investigation was made to determine whether other binary titanium alloys with P-stabil-izing elements would exhibit a crystallography of transformation similar to that of Ti-Mn alloys. Furthermore, since martensite platelets can be induced by deformation under certain conditions, it was of interest to investigate whether the mode of deformation, compressive or tensile, would influence the formation of martensite platelets on a specific plane in an alloy system which possesses two martensite habit planes. Experimental Procedure The material used for the preparation of the binary alloys of iodide titanium with molybdenum, chromium, and iron had the following purities: 99.99 pct iodide titanium, 99.9 pct molybdenum, 99.423 pct chromium, and 99.9 pct iron. The compositions of alloys listed in this paper are in nominal weight percentage. All specimens used were prepared and treated according to the procedure described in reference 1, unless stated. For the subzero temperature treat,ment the following experimental schedule was followed. After specimens had undergone the grain-growth treatment, they were quenched into an ice-water bath and were then metallographically examined. In specimens of higher alloy content, no martensitic transformation was observed. In those in which mar-tensitic transformation did occur, only specimens in which the martensite platelets existed as fine needles in localized regions were used. All specimens were reannealed 17 hr at 1200°C, quenched into ice water. and the capsule was broken. They were held in the ice water for from 5 to 10 sec, then transferred to a liquid-argon bath. This stepped quenching procedure was found to be more efficient than direct quenching into liquid argon. In the latter case, as soon as the hot specimen was immersed in the liquid argon, a protective, insulating layer of argon gas formed, and the specimen continued to glow vividly in the bath for some time. In the study of the habit behavior of martensite produced by deformation, specimens were deformed at room temperature either by compression, tension, or rolling. Martensite habit planes were determined by the two-surface analysis procedure described in reference 1. A stereographic net of 153/4 in. diam was used throughout the investigation. The method for determining the orlentation relationship between martensite and the matrix follows that used by Greninger and Troiano.&apos; A diamond-polishing table with its auxiliaries was used in order

Jan 1, 1957

Jan 1, 1961

By CLARENCE WM. POY

THE most common difficulty faced by an engineer or mine operator when opening a new property in a new field is the lack of roads and of cheap transportation. This one item often swings the balance of success or failure in starting a project. In Alaska, as elsewhere, such problems are more or less serious. In the boom days around the Valdez district, as well as in other parts of this territory, freighting was accom¬plished by dog teams or horses, or even by men that were willing to put their shoulders into harness, because there were virtually no roads. More important, there was only one time when supplies could be transported, and that was when there was suffi¬cient snow on the ground following a heavy wind. Then, and only then, could one depend on the snow to support horses and sleighs, and be sure that the gulleys, streams, and crevices in the glaciers were filled with snow to avoid pitfalls. These methods were used when one had no roads, no streams in the summer to float a barge, or even a trail for a pack train. If the snow was deep and soft, trans

Jan 1, 1935