Search Documents

By Fred H. Perfect

The thermite process, now approximately 80 years old, has heretofore been practiced in ceramic vessels. This paper outlines the successful production of several million pounds of alloy produced in zuater-cooled copper vessels. THE high temperatures necessary to produce fluid high-alumina slags have probably discouraged earlier workers from attempting to utilize water-cooled vessels. The following is a report of the successful application of this method, together with a report of the physical and chemical problems which had to be solved to make the process practical. About 1955, when Reading Alloys was more concerned with the production of ferrotungsten than with most other types of alloys, it was found to be exceedingly difficult to predict the reaction rate that one would experience from one tungsten ore to another . This difficulty was increased for two reasons: the physical state of the ore as received was seldom uniform, and the size of the mass to be reduced is a very important factor in developing the proper mix for the final reaction rate and temperature. For example, the reduction of ferric oxide with aluminum would theoretically produce temperatures of about 2600°C, and, in spite of the losses due to radiation, the energy is quite sufficient to produce a very fluid slag and iron effecting a very clean separation. On the other hand, the reduction of ferrous oxide with aluminum, while it is not as energetic as the first reaction, nevertheless should give temperatures above 2000"C, which should cause separation of alumina and iron, but, in practice, this is not the case and good fluid slag is not obtained. The heat of reaction, calculated from the thermo-dynamic heats of formation of the constituents of the reaction, offers a convenient guide to the feasibility of a thermite reaction. Thus, the values listed in Table I can be used as an approximate guide for estimating the results which may be expected in the reduction of various oxides and combinations of oxides using aluminum as the reducing agent. As a generalization, those reactions releasing approximately 600 cal per g of total mass represent the lower limit at which to expect separation of slag and metal. On the other hand, those reactions which release 1100 to 1200 cal per g are too violent to be used successfully without the addition of considerable inert material, such as lime, fluorspar, and so forth. Reaction rate is also a very important factor. This, of course, is governed very largely by the sizing and intermingling of the oxidant and reductant and by the starting temperature of the reactants. This is why those figures shown in Table I can only be a general guide. Further, it must be understood, that by adding powerful oxidizing agents, such as nitrates, chlorates or metallic oxides, such as molybdenum trioxide or chromium trioxide, certain problems respecting low temperatures are not necessarily solved. This is true in the addition of oxidants, such as sodium chlorate. By adding too high a concentration of sodium chlorate as a booster for a particular reduction, explosions are generated. Generally, they are of an intermittent type so as to give a Roman Candle effect to the reduction itself; with each surge resulting from a minor explosion more and more material is thrown

Jan 1, 1968

By WILLETT G. MILLERS

GENERAL RECEPTION COMMITTEE.-Willett G. Miller, Chairman; F. G. B. Alan, Hon. Frank Cochrane, Eugene Coste, Thomas W. Gibson, Cyril W. Knight, J. C. Murray, 0. N. Scott, Alan Sullivan, J. B. Tyrrell, J. W. Wells, A. B. Willis. COBALT RECEPTION COMMITTEE.-Arthur A. Cole, Chairman; Will. Ask with, R. W. Brigstocke, Robt. Bryce, Fred Coombs, M. I. Culbert, I. R. Drummond, J. W. Evans, A. Ferland, F. N. Flynn, E. L. Fraleck, S. R. Heakes, Joseph Houston, D. L. Jemmett, I. R. Jones, Major Leckie, Capt. Jack Leckie, R. W. Leonard, W. H. Linney, Alexander Longwell, Frank Loring, Murdock McLeod, John Martin, D. B. Rochester, W. E. Running. COBALT RECEPTION COMMITTEE (Ladies).-Mrs. A. A. Cole, Mrs. A. Edwards, Mrs. R. Jennings, Mrs. S. H. Logan, Mrs. A. Longwell, Mrs. H. F. Marsh, Mrs. J. Smith. SUDBURY LOCAL COMMITTEE.-Mayor L. O'Connor, Chairman; S. Fournier, Secretary; A. H. Beath, W. J. Bell, F. B. Bennett, D. M. Brodie, J. S. Buchanan, F. C. Busby, Wm. Chalmers, R. Dorsett, W. A. Evans, John Frawley, J. S. Gill, A. B. Gordon, J. G. Henry, T. N. Kilpatrick, Major Leckie, Chas. McCrea, John McLeod, Wm. McVittie, R. Martin, R. S. Mitchell, J. H. Morin, J. A. Orr, James Purvis (President Board of Trade), C. R. Reid, Major Smith, W. W. Stull, J. F. Templeton, S. E. Wright. The first session, held in the Banquet Hall of the King Edward Hotel, was called to order Tuesday, July 23, 1907, at 2.30 p.m., President John Hays Hammond presiding. Prof. Willett G. Miller, chairman of the General Committee, introduced Alderman J. J. Graham, who, in behalf of the City of Toronto, extended a hearty welcome to the members and guests of the Institute. To this welcome, President Hammond replied in a few well-chosen and hearty remarks. In the hall in which the session was held there was exhibited a fine, full-length, life-size portrait of Dr. Rossiter W. Raymond, in 1871 Vice-President and acting President, in 1872, 1873 and 1874 the elected President, in 1876 and 1877 Vice-President, in 1883, by appointment of the Council, and for the last 24 years by annual election, Secretary, of the Institute. Dr. James Douglas, of New York, N. Y., on behalf of numer-

Sep 1, 1907

Jan 1, 1967

In 1962, minerals beneficiation showed definite signs of coming out of the doldrums into which it has drifted after the uranium boom. Demand by steelmakers for high-grade iron pellets has created the need for concentrating plants to upgrade specular hematite by spiral concentration or flotation and magnetites by magnetic means and flotation. According to a paper given at the AMC annual meeting by C. S. Arms of Pickands Mather, "the shipment of pellets, started in the mid-1950's, has increased to 17.6 million tons in 1961 from North American operations. Many plants already underway will raise this production to about 42 million tons by 1965. This will be a very sizeable percentage of the total iron ore production contemplated by that date." Iron ore concentration methods are gradually raising the assay of pellets into the 65 to 69% Fe range and lowering silica to the 4 to 7% range. Quebec Cartier's Lac Jeannine concentrator went into operation in late 1961 and all grinding units were running by 1962. The Iron Ore Co. of Canada's new Carol Lake plant was started in mid-1962.

Jan 2, 1963

By Paul. D. Merica

I LIKE to look upon the award this year also as a recognition of the importance of metallic materials of construction to the engineer and of the active progress which I believe is continually being made in almost all branches of that field today. It has been said that metals are the material backbone of industry and technology. Well in that case, I suppose we metallurgists are industry's bonesetters. And it is possibly not inappropriate that we should occasionally give some atten¬tion to those bony structures of our industrial activities upon which engineers in other fields hang their manifold and striking creations. What is going on in the field of metals development? Well, in the first

Jan 1, 1938

By D. W. Smith, Robert F. Mehl

It has been shown by numerous studies that the orientations of new metal crystals are determined by the orientations of the crystals in the original matrix, whether these new crystals are formed by recrystalliza-tion, by precipitation from solid solutions, or by transitions in the solid state. The orientations of crystals formed by recrystallization of cold-worked metals that bear preferred orientations are occasionally simply related to the initial preferred orientation; often, however, the relationship is not simple, but complicated and obscure in origin.1 The orientations of crystals formed by precipitation from solid solutions have been shown by many studies in this and other countries to be determined by the orientation of the crystals of the solid solution stable at the higher temperatures, though here again complicated cases have been found and no general theory is available.2 Related to this latter class are the relationships found in crystals formed by suppressed transforma-

Jan 1, 1935

By D. W. Smith, Robert F. Mehl

It has been shown by numerous studies that the orientations of new metal crystals are determined by the orientations of the crystals in the original matrix, whether these new crystals are formed by recrystalliza-tion, by precipitation from solid solutions, or by transitions in the solid state. The orientations of crystals formed by recrystallization of cold-worked metals that bear preferred orientations are occasionally simply related to the initial preferred orientation; often, however, the relationship is not simple, but complicated and obscure in origin.1 The orientations of crystals formed by precipitation from solid solutions have been shown by many studies in this and other countries to be determined by the orientation of the crystals of the solid solution stable at the higher temperatures, though here again complicated cases have been found and no general theory is available.2 Related to this latter class are the relationships found in crystals formed by suppressed transforma-

Jan 1, 1935

By J. L. Lytton

The flow-stress recovery of high-purity aluminurn following a 10 pct tensile prestrain was studied in terms of a fractional flow-stress recovery parameter fr. The flow-stress recovery behavior was related to the dislocation arrangements using transmissiort electron rnicvoscopy. During recovery at 120° and 160°C, nearly stable strength levels were attained, the strength level for 120°C recovery being greater than that for 160°C. This stabilization of flow stress was related to the formation of meta-stable dislocation networks bounding nearly perfect cells. Both network formation and the annealing of dislocation loops were found to be recovery mechanisms, and the stronger metastable strength level joy 120°C recovery was related to a smaller average cell size. Analysis of the networks was consistent with the reaction of sets of dislocations with a/2 (110) Burgers vector to give product Burgers DURING isothermal annealing of cold-worked metals, a degree of softening occurs without re-crystallization, and the processes responsible for this change are termed recovery processes. During recovery annealing, the dislocations generated during cold work become rearranged into low-energy configurations, and as much as 50 pct of the stored energy is released."' The relationship between this rearrangement of dislocations and mechanical behavior is of considerable importance, since the dislocation substructures formed during recovery provide a significant degree of low-temperature strength3j4 and can favorably alter the course of primary creep at high temperatures.4 The purpose of the present study was to relate the flow-stress recovery behavior of high-purity aluminum to the substructural modifications that occur. Electron transmission microscopy was therefore employed for direct observation of dislocation substructures at various stages of recovery following 10 pct prestrain. Several investigators5-' have proposed that dislocations can become rearranged or lost during the preparation of thin foils. It was found early in the present study that the dislocation structures in the thicker regions of the foils changed in a systematic way during the course of recovery. Therefore, it is unlikely that substantial losses or rearrangements occurred during thinning. This point will be discussed in more detail later. The results of various investigators indicate that recovery processes in fcc metals can result in release of 50 pct or more of the total energy stored in the as-prestrained metal, this percentage decreasing with increasing prestrain.' Alloying elements or impurities tend to increase this percentage. The release of stored energy of fcc metals during recovery appears to occur by 1) annealing of point defects if the deformation occurred at sufficiently low temperaturesg and 2) rearrangement of dislocations into low-energy Configurations.1,2In bcc metals, the annealing of dislocation loops has also been observed during recovery after prestrain,10-12 and it has been proposed that this is a recovery mechanism for unidirectionally strained fcc metals.' The density of dislocations in bcc metals has not been observed to decrease appreciably during recovery,10 although the formation of regular dislocation networks has been observed. has shown that the formation of such networks can result in elimination of long-range stresses and can lead to significant release of stored energy without dislocation annihilation. It might thus be expected that network formation is a significant recovery mechanism in fcc metals, although extensive network formation has apparently not been reported in controlled recovery experiments. The formation of sub-boundaries in aluminum has been observed by various investigators13'17 during recovery studies of aluminum, but the structure of these boundaries was not resolved. In this regard, it is significant to note that Bailey and Hirsch,' using transmission electron microscopy, detected no network or sub-boundary formation during recovery of 99.99 pct Ag. Furthermore, Clarebrough et al.2 found no such rearrangements during recovery of copper. EXPERIMENTAL PROCEDURE The high-purity aluminum used in this investigation was obtained in the form of 0.125-in.-thick sheet. Spectrographic analysis revealed that the sheet was 99.995 pct A1 with the following weight-percent impurities: 0.001 Cu, 0.002 Fe, 0.001 Si, and 0.0004 Mg. The as-received sheet was in the heavily cold-rolled condition. The as-received sheet was cold-rolled at room temperature to 0.040-in.-thick sheet in the longitudinal direction, which was the original rolling

Jan 1, 1965

Jan 1, 1967

By E. W. Rouse

THE year 1936 has seen rehabilitation of many plants which had been closed or severely curtailed. The Steptoe smelter of the Nevada Consolidated Copper Co. has been transformed by a rearrangement of the flow of material and utilization of mechanical handling to a maximum. The Phelps Dodge Corp. reports the construction of newer and better reverberatories at the Copper Queen smelter, and of particular interest, a single high-pressure waste-heat boiler placed directly over the uptake. There has also been a complete reconstruction of the smelter at the Laurel Hill plant of the Nichols Copper Co.

Jan 1, 1937

By Joseph Jensen

MANY fields have been zoned by nature with shales and intermediate waters between oil zones. Limitations thus imposed have been the basis on which the field was developed. In contrast thereto, in the Ventura Avenue Field, nature proved more generous. Always expecting to find such similar limitations, operators drilled deeper and deeper into the oil zone without finding any distinctive shale bodies other that the Gosnell shale and only one intermediate water, which became the point below which the final water shut-off of each well was made. Thus, on top of the structure, about 3300 ft. of oil-bearing zone has been penetrated below this intermediate w9ter-a distance of 4000 ft. below the Gosnell shale. At first it seemed that the greater the penetration in the zone, the better the well. The error of this assumption became evident

Jan 1, 1930

By P. van Meurs, C. van der Poel

From observations of the linear displacement of oil by water from a porous medium as visualized in transparent models, new insight into the mechanism of vircous fingering, as occurring in the case of unfavorable oil-water viscosity ratios, has been obtained. A mathematical description of the observed phenomena leads to formulas. expressing both oil production and pressure drop across the formation as a func-tion of cumulative water injection with the oil-water viscosity ratio as a parameter. Theoretical results are compared with those obtained from scaled laboratory experiments in sand-filled rubes in which water was injected at the one end and production was obtained from the other end. In the second part of the paper the same principles are used to calculate a more realistic production scheme in which production of oil and water is obtained from wells regularly distributed over the field. Results show satisfactory agreement with production data of an actual oil field. Application of the theory is extremely simple as only a limited number of readily available parameters have to be known and results are presented in an analytical form. INTRODUCTION When oil is displaced from a porous medium by water having a viscosity lower than the oil. the oil-water interface is essentially unstable and has the tendency to break up into what are called "fingers" or "streamers". This Viscous fingering has been noted before by Engelberts and Klinkenberg' and has recently been demonstrated in transparent models by van Meurs-. It is highly questionable whether it is at all possible to perform relative permeability measurements In the laboratory reproducing the same distribution of water and oil in the cores as Present in practice. Therefore, we based our descriptive theory on an idealized model which was "tailored" to the fingering mechanism as observed in transparent models under scaled conditions. This approach was the more attractive, as a highly simplified model had already yielded an adequate description of the process. Though we are aware our theoretical approach can be extended in several ways, it is given here in its simplest form to explain the fundamental principles and to avoid complicated formulas. SIMPLEST CASE OF A LINEAR DRIVE Observations and Theoretical Model In Fig. 1 a series of photographs shows how water penetrates into a formation saturated with an oil which is considerably more viscous than the water. The technique for obtaining these photographs, using transparent models, has already been described?. The fingers can be clearly observed and are seen to be mainly parallel to the flow direction. Note that the contours of these fingers are not smooth but show protrusions of water enclosing oil pockets.

By William P. Blake

We are so familiar with water in its liquid and its solid form, that we seldom think of it as a mineral, and still less as a mineral product of any considerable industrial importance, though in the form of ice it is mined and stored up in enormous quantities yearly. The industry is peculiarly American, and in no other country has the business of cutting and storing ice been so well systematized and perfected. The interest has grown steadily from year to year, until it has attained large proportions, the annual production being counted in millions of tons, requiring, in the aggregate, a large investment of capital in all the Northern States. It gives employment, also, to thousands of men and horses, in the depth of winter, when farming work cannot be carried on. Ice is not only a luxury, but a necessity, in our climate, and is indispensable in many manufacturing operations: and finds constantly increasing applications and uses. As the industry has grown, so the necessity for suitable implements and tools has grown with it, and it has become necessary to systematize and cheapen the methods of handling such a large amount of material with rapidity and economy. As the industry is properly a branch of mining, and as our mining literature does not, to my knowledge, contain any description of the methods and appliances used in it, it seems desirable to place a brief description on record in our Transactions, and I therefore offer to the Institute the following outline description, based partly upon observations for several years past of the methods and processes employed, and partly upon the information obtained from prominent ice-miners and from the manufacturers of ice-tools. My acknowledgments are particularly due to the firm of W. T. Wood & Co., of Arlington, Massachusetts, for much information in detail, and also to the Knickerbocker Ice Company, of Philadelphia. The wood-cut blocks used in the illustration of this paper, have been kindly lent by both of these firms. The sequence of operations in getting ice is as follows : 1. Wetting down a light snow. 2. Scraping off an excess of snow, if present. 3. Marking out the field. 4. Ploughing and cross-ploughing. 5. Cutting the channel and detaching large floes.

Jan 1, 1883

By E. H. T. Whitten

Fundamental principles of trend surface analysis are briefly reviewed. Recent analyses of several granite masses illustrate the method of estimating the quantitative regional composition and also variation trends. Mineralogi-cal, bulk chemical, and other quantitative variates can be employed. Such results should improve gravimetric surveys (etc.) relying on correction terms based upon estimated rock composition. For the first time realistic estimates of the mean composition of rock bodies can be made with the aid of trend components. Deviation maps hold promise for delimitation of disseminated mineralized areas. Deviations comprise residual "anomalies" after removal of trend components. In petrogenetic work such deviations have been shown to reflect local influences (e.g., contamination of magma by assimilation of xenoliths or country rocks of the envelope). Similarly, mineralization should be reflected as deviations standing out from background trends. Actual examples are given. Present results largely involved projection of data onto a horizontal plane, but if sufficient data are available use of three spatial coordinates increases accuracy for prediction in "unexposed" areas. Regression analysis shows that statistical correlations between variates for regionally distributed specimens are often strong (particularly with percentage data). Hence, in preliminary surveys more easily determined variates may sometimes be employed to gain first estimates of the distribution of components more economically significant. The sampling plan is of paramount importance. Unless a suitable sampling plan is devised and adhered to rigorously during collection of the samples, all subsequent analysis is liable to strong bias and to yield spurious estimates of the truth. For a wide variety of purposes it is becoming necessary to assess the quantitative composition and variability of rock masses and mineralized zones of various types. In petrology and petrography this is something of a break with tradition, because virtually all descriptions heretofore have been qualitative. Although vast amounts of qualitative data have been compiled, little is known about the quantitative behavior of rock components. However, if variability of rocks could be understood and expressed with sufficient accuracy, there would be considerable advantage to both economic and petrogenetic problems. For example, if, on the basis of a limited series of observations, the three-dimensional geometry of a disseminated orebody (or ore-bearing formation) could be predicted accurately, it would be possible to extrapolate with confidence the structure into unexposed areas. The following example based upon the geometry of an igneous cone sheet illustrates the point. The significant rock-unit gives outcrops at a number of points on the exposed surface ABCD (Fig. 1A). Study of n exposures may enable a geologist to predict that the rock-unit is circular in form and thus indicate where the unit can be expected in unexposed terrain. Such observations are made at sites with u, v coordinates, but, if subsurface information is available at sites with uvw coordinates, it will eventually become possible to predict accurately the three-dimensional form of the rock mass. Geologic rock masses or mineral deposits are not generally as regular and symmetrical in geometric form as the body illustrated in Fig. 1A. However, even where the broad limits of a major rock mass are known, a more acute problem arises in attempting to obtain detailed quantitative estimates of its internal variability; it is difficult to predict the variability of a mass from a limited number of observa-

Jan 1, 1961

By Walter Fuchs

IT is now generally conceded that coal is the product of deposition and transformation of debris of forests and swamps.29 Ample data are available to illustrate the metamorphosis of biochemical substances through biological action; other data show the progressive regional metamorphism existing in coal beds;25 and numerous examples of change effected by intrusion of igneous dikes into coal deposits have been established.23 However, often the relative importance of the biological and the geological factor in determining the character of the various natural coals is a debatable question. Since both biological and geological factors are ever present in nature, the problem, at first glance, would appear to resemble certain probability problems: specifically the simultaneous toss of two coins, with the biological factor as heads and the geological as tails. The probability is 2:I for the combined effect of both factors, as compared to the exclusive effect of either one. if the a priori probability is the same for each factor. This condition can be analyzed by a thermodynamic treatment of data, which may be obtained from a consideration of pertinent biological, chemical, geophysical and geological facts. SYNOPSIS OF BIOLOGICAL AND CHEMICAL FACTS The biosphere is not sterile; i.e., microorganisms are always present. Microorganisms have been established in the ocean deep, under the ice of the polar regions, in the sand of the deserts, and in swamps far below the surface. The various biological media may be acid, neutral, or alkaline, and they may or may not be readily accessible to air. Microorganisms are encountered almost everywhere, except where the temperature is not within the range tolerable by microbial life. Of course, with changing conditions, the type of microorganisms will change. All chemical products of life-proteins, fats, carbohydrates, lignins, waxes, resins may serve as a habitat of microorganisms. In the decomposition of a medium, some microorganisms macerate organic matter mechanically and remove certain constituents for their own nutrition; others decompose a large part of the organic matter but may leave certain constituents undecomposed. Some attack only certain specific ingredients of the organic matter. All of them build up cell substance. The nitrogen content of the medium largely determines the degree of decomposition. Below 1.7 per cent nitrogen, growth of microorganisms and hence decomposition of organic material is retarded; consequently organic material will accumulate. l7,32 Such accumulations of organic material may give coal eventually. Coals differ in type and rank. The nature of the original vegetation and the conditions attending the transformation of the accumulated debris determine the type of coal such as bright, splint, cannel, and algal or boghead coals. Chemical analysis of representative samples of a given type of

Jan 1, 1941

By A. B. Parsons

Jan 1, 1971

The growth and influence of Sherritt Gordon Mines Ltd. in the nickel producing industry has been quite phenomenal. Although the company's Lynn Lake deposit in Manitoba was actually dis- covered in 1941, it was not until 1945, when men and materials were more readily available as a result of the end of World War II, that the area was staked and news of the discovery leaked out. As a result of the discovery, Professor Frank Forward of the University of British Columbia was commissioned by Eldon Brown, then President and Man- aging Director of Sherritt, to develop a new nickel refining process. A pilot plant, based on the results of Professor Forward's research, was constructed in Ottawa, and after the successful testing of the Lynn Lake ore, Chemical Construction Co. was given a con- tract in 1952 for construction of a producing plant. By 1954, the Fort Saskatchewan refinery was operating at an annual production of 15 million lb of nickel metal in the form of briquetts or powder. Capacity has since been increased to 30 million lb.

Jan 10, 1968

By B. A. Wilcox

ThERE are several reports in the literature which indicate that both solid-solution hydrogen and hydride precipitates can promote low-temperature em-brittlement of tantalum.1-3 For example, Imgram et al.2 showed that hydrogen additions in the range of 140 to 580 ppm promoted a ductile-to-brittle transition at slightly above room temperature in both wrought and recrystallized tantalum. This contrasts with the observation that tantalum of norma1 purity is very ductile, even at liquid-nitrogen temperature. Imgram et al. also found that hydrogen additions caused a deterioration of notch tensile properties of tantalum. The purpose of this communication is to present some limited evidence that hydrogen can also cause fatigue embrittlement of tantalum. The material used in this investigation was wrought, stress-relieved (1000°C, 1 hr), are-melted tantalum rod (5/8-in. diameter) containing the following impurities in weight percent: 0.005 C, 0.007 02, 0.0005 H2, 0.003 N2, 0.08 Cb, 0.01 W, and 0.01 Fe. Hydrogen charging was done in an atmosphere of flowing dry hydrogen for 3 hr at 600°C, followed by an homogenizing anneal in purified argon for 15 min at 600°C, and cooling in an argon atmosphere. Typical micro-structures of the hydrogen-free and the hydrogen-charged materials are shown in Fig. 1(a) and Fig. 1(b), respectively. Fig. 1(b) shows the appearance of hydride precipitates which, in many cases, formed preferentially parallel to the rod axis. The hydride dispersion was uniform across the diameter of the specimen. The fact that the precipitate was a tantalum hydride was tentatively confirmed by X-ray diffraction on a metallographically prepared surface. After hydrogen charging, chemical analyses by vacuum fusion revealed the hydrogen content to be 0.0295 wt pct. In addition, the oxygen and nitrogen contents were slightly raised to 0.0095 O2 and 0.005 N2.

Jan 1, 1964

By Frank Rieber

THE study of earthquakes long ago developed the fact that by studying the travel times of the various groups of waves from the same earthquake, as received on seismographs at varying distances, major discontinuities in the earth's crust could be reasonably well defined. Using this original discovery, and adapting the mathematical methods originally devised in seismology for determining the depth below the surface at which such discontinuities occur, other investigators were able to develop a new branch of seismology which promises to be extremely useful in extending the boundaries of our information on local conditions below the earth's surface. As an outstanding example of the applications of this work, we have the so-called "seismograph" exploration of the Gulf Coastal region, which has resulted in the discovery of a large number of salt domes, from many of which oil fields may be developed. The original seismological investigations, from which different major discontinuities in the earth's crust were deduced, as well as these later successful experiments in locating salt-dome structures, involve relatively simple problems. In each case we are dealing with surface materials in which elastic waves will be propagated with a fairly definite velocity. Under this material we have something quite different, in which the elastic waves will be propagated with a much higher velocity. The transition from one medium to the other is likewise relatively abrupt. For example, in the Gulf Coastal region the sedimentary formations have a velocity of 6000 or 7000 ft. per sec., while the velocity of elastic waves in the cap rock of a salt dome may exceed 15,000 ft. per sec. Under such conditions, delineation of the formation is a relatively simple matter, and, furthermore, there is very little opportunity for ambiguous results.

Jan 1, 1928

By E. C. Olsen

This paper describes the unusual hazardous conditions encountered in mining thick, inclined coal beds under heavy cover in Carbon County, Utah. This description includes heavy roof conditions, sloughing ribs, steep pitches, and severe bouncing experience. Emphasis is placed on the top bench system of mining and development in the top half of a 16-ft seam, under the roof rock, which is bolted, and the recovery of the bottom coal on retreat; success of bolted roof and ribs; and shuttle car haulage on pitches up to 25%. The use of protective cages for operators of face equipment, the guarding of belt conveyor systems to prevent injury associated with deliberate entry, and the positive lockout of electrical equipment is described and illustrated. Most coal mining areas of the Western United States are characterized either by thick beds, steep pitches or heavy cover. Individually, each of these may present inherent safety hazards that in- fluence mining. When all are met at one location, the combined effect is to make the safe operation of the mining property a challenge to management. These combined conditions are met in the coal mines of the Columbia-Geneva Steel Div. of the United States Steel Corp., in southeastern Utah. This coal bed measures up to 16 ft in thickness, the pitch is as much as 25% and mining is under a cover approaching 3000 ft. The Sunnyside coal bed is found in the Book Cliff Mountains, a great escarpment extending from west of Castle Gate, Utah, some 180 miles to Grand Junction, Colo. West of Green River, Utah, the Book Cliffs swing sharply to the north because of the domelike uplift of the San Rafael Swell to the southwest. It is in this northerly extension of the Book Cliffs that the Sunnyside coal in the Blackhawk Formation of the Mesa Verde Group, Upper Cretaceous Age is found. The strata are transected by numerous faults with from a few inches to as much as a hundred feet of displacement. All of these faults have had some effect on the mining operation, either in roof control or, in the case of major faulting, the pattern of mine development. MINING PRACTICES Mining has generally been confined to the Lower Sunnyside Seam which measures from 7 to 16 ft in

Jan 1, 1963