Search Documents

By Donald W. Mitchell

Research shows that water neutralizes the explosion hazard of coal dust when present in sufficient quantity and when intimately mixed with the dust. The quantity of water required to neutralize coal dust and coal-rock dust mixtures is about equal to the limiting moisture adsorptive capacity of the dust; the adsorptive capacity increases with increase in the fineness and volatile content of the coal. Pools of water or high atmospheric humidity do not reduce the explosion hazard. Although wetted dust is less dispersible than dry dust, poor dispersibility cannot be relied on as the sole safeguard against explosion. Dust mixtures that contain water in excess of their limiting adsorptive capacity are dispersed and ignited by severe initiation sources. Pure coal dust adsorbs water with difficulty and retains water poorly; adsorption and retention is increased by the addition of rock dust the coal; the rock dust agglutinates wetted coal and assures that incombustible is present should drying occur. Therefore, it is advantageous to rock-dust wet areas in bituminous coal and lignite mines. When coal-rock dust mixtures are wetted and subsequently dried, the explosion hazard is about the same as for dust which was not wetted.

Jan 1, 1962

By J. -W. Kim, Y. -B. Kang, H. -G. Lee

The effect of SiO2addition on the decomposition of Li2CO3was investigated at temperatures up to 1000ºC. It was found that addition of SiO2greatly enhanced the decomposition of Li2CO3. The main decomposition reaction started at around 600ºC, and completed just above the melting point of Li2CO3. The major decomposition product was Li2O?SiO2irrespective of the Li2CO3to SiO2mixing ratio while both reactants were available. It was ascertained that a liquid layer betweenLi2CO3and SiO2particles formed and facilitated the decomposition reaction. The governing reaction of the decomposition was the one between the dissolved Li2CO3and SiO2in the liquid layer to form Li2O?SiO2. The decomposition rate was independent of the Li2CO3/SiO2mixingratio until either one had been completely exhausted. When excess Li2CO3existed, it further reacted with the initial product of Li2O?SiO2to form 2Li2O?SiO2. When SiO2was found in excess, on the other hand, no further reaction took place. This is attributed to the fact that uponLi2CO3exhaustion there is no liquid phase available to facilitate further reaction. The apparent activation energy of the decomposition of Li2CO3in existence with SiO2is 198 kJ mol-1.

Jan 1, 2004

By Thomas O. Glover

Cameroon's mineral industry continued to be dominated by crude petroleum. The country's economic development depended on the production and export of crude oil. Oil output was estimated to be 56 million barrels in 1984 compared with 47 million barrels in 1983 and 39 million barrels in 1982. The country's only refinery processed approximately 16,000 barrels per day of crude oil in 1984, operating at slightly over 50% capacity. This volume, however, supplied the domestic need for motor fuel and heating oils. Cameroon's economy continued to expand despite problems and setbacks stemming from the attempted coup of April 6, 1984. Gross domestic product (GDP) growth in 1984 was 6.5%, the same rate as in 1983. Offshore crude petroleum production was the chief factor in the sustained economic growth. The country also maintained a relatively strong balance-of-payments position through oil exports. Investment, ranging up to 25% of the GDP, greatly contributed to sustained growth. The oil sector contributed approximately 14% to Cameroon's GDP in both 1983 and 1984.

Jan 1, 1986

By G. A. Craig

The Moon, asteroids, and planets of the solar system represent the most distant caches of wealth that humanity has ever considered recovering. Yet, in addition to the potentially recoverable values represented there, harvesting off-Earth resources has a second, almost incalculable sustainable benefit in that they can be retrieved with absolutely no damage to Earth. Previous research mostly assessed the potential of asteroids and the Moon for mining purposes from a theoretical and scientific point of view. These studies investigated drawbacks that could be experienced in this type of operation, but no detailed economic evaluation that is meaningful for mining project management has been conducted and the parameters that are most likely to make an operation feasible are unknown. This paper provides a preliminary economic and sensitivity analysis of a possible off-Earth mining business extracting minerals from an existing asteroid.

Jan 1, 2014

By J. R. Cobble

As part of the Federal Bureau of Mines project to develop new or improved materials for metallurgical furnace applications, the Tuscaloosa (Ala.) Research Center has conducted research to develop a reproducible laboratory test for evaluating the resistance of refractories to molten slags. Tests were conducted with a slag representative of slag used to produce mineral wool. A rotating cylindrical furnace was lined with the brick being tested, and it was operated at temperatures up to 1,660° C for periods ranging from 8 to 32 hours. The effects of such variables as slag temperature, rotational velocity, charge rate, and contact time on refractory erosion were determined. The research demonstrated the reproducibility of the test procedure developed.

Jan 1, 1980

By Felipe Amélio de Lucena

Ligas amorfas e nanocristalinas à base de ferro apresentam propriedades excepcionais, como alta dureza e resistência ao desgaste com taxa de resfriamento entre 103 e 105 K/s. Assim, este trabalho objetiva a solidificação rápida (SR) da liga à base de ferro fundido (FoFo) com adições de Boro e Nióbio, resultando na composição química (Fe65Cr17Mo2C14Si2)88B8Nb4 (%at.). A liga foi processada através de melt-spinning, no forno Discovery® Plasma e Conformação por Spray (CS) e caracterizada por: DSC, DRX, MEV e microdureza Vickers. Foram obtidos: fitas amorfas (40 µm) através de melt-spinning, chapas (1,0 e 2,0 mm) por (SR) e CS da liga (Fe65Cr17Mo2C14Si2)88B8Nb4, com depósito (1,0 e 2,0 mm) e pós overspray (20 até 180 µm). A caracterização mostrou fitas amorfas, pós overspray nanocristalinos e chapas (SR) e depósito (CS) cristalinos com as fases: Fe-a, Fe-?, Cr7C3, FeNbB e Fe2B, com respectivas microdureza Vickers de 1044 ± 102 (HV1) para o depósito CS e 1480 HV para a chapa de 2,0 mm, mostrando alta dureza.

Aug 16, 2017

By Ren G. Dong, Richard McCormick, Dan E. Welcome

Vibration exposure at workplaces is generally multi-axial. The health effects of vibration exposure also likely depend on the vibration direction. Therefore, there is a wide interest in the simulation of multi-axial vibration in laboratory experiments. Advances in technology have led to the development of a new 3-D test system for studying hand-transmitted vibration exposure and health effects. The purposes of this paper are to introduce the system and to present the results of its preliminary evaluations. Test System As shown in Figure 1, the system is basically composed of three vibration generators, a multi-axis vibration control system, instrumented handle, handle fixture, and shaker-fixture linkages (stingers). [ ] Figure 2 shows the array of three vibration generators (MB Dynamics, Energizer BLACK-500 lbs) and their associated support bases and foundation developed by MB Dynamics (Cleveland, USA), which create the 3-axis simultaneous motion. These electrodynamic exciters are powered by power amplifiers which provide current proportional to the analog drive signal from a controller. The controller (JAGUAR Multi-Input/Multi-Output closed-loop vibration controller) was provided by Spectral Dynamics, San Jose, California, USA). NIOSH-designed instrumented handle was equipped on the system.

Jan 6, 2006

By T Do, J Siliezar, M Larson

With the expansion of magnetite projects in Australia has come the opportunity to take advantage of newer technologies that were not necessarily available when the magnetite industries of North America and Europe were maturing. One of these technologies is the IsaMill, originally developed for the economic treatment of ultra-fine grind (UFG) duties of Mount Isa Mines. As understanding of the IsaMill has increased, so too has the ability to process coarser feeds while maintaining the same energy efficiency advantage and tight product size distribution that originally made the IsaMill so attractive. In the case of magnetite the hard non-elastic ceramic grinding media is ideally suited to the grinding duty when compared to steel grinding media. The centripetal separator and naturally steep product size distribution curve provide a mill discharge that maximises the critical concentrate grade. This paper analyses the effect of the IsaMill grinding technology on the full-scale Ernest Henry Mine (EHM) magnetite operation along with pilot and lab scale demonstrations of optimisation. Issues encountered and the solutions to maximise the mill throughput and quality are examined in an effort to promote better understanding across the industry. CITATION:Larson, M, Do, T and Siliezar, J, 2013. Enhancing magnetite returns - the benefits of IsaMilling, in Proceedings Iron Ore 2013 , pp 411-416 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Lawrence Williamson, Randall J. Essex, David P. Field

As part of a $2.2 Billion bridge project that will link Indiana and Kentucky, an interchange project northeast of Louisville will require the mining of a 6-lane tunnel system about 2,000 ft long in order to cross beneath the historic Drumanard Estate. This paper will discuss preliminary engineering that has been undertaken to compare two-bore and three-bore layouts, the planning of an exploratory tunnel facility, and the potential for including a test chamber to investigate the ability of high capacity roadheaders to mine the 22,000 psi limestones.

Jan 1, 2005

By J. N. Van der Merwe

The principal goal of the research described in the paper was to determine, by measurement of pillar scaling on pillars that have not failed, whether the pillar life prediction method developed by van der Merwe (2003) was valid as it stood or whether adjustments were necessary to the rates indirectly derived from observation of failed pillars. To this end, measurements were taken on over 350 pillars at 13sites on 6 mines. The project was done as a collaborative effort between the University of Pretoria, the Nancy School of Mines and CSIR Miningtek. During the course of the investigation, it was found that the majority of pillars display maximum scaling at mid height, that there was no clear preferential direction of pillar scaling, and that pillar corners do not scale significantly more than the mid pillar areas. The most important conclusion was that the scaling rates found by measurement agreed with the inferred rates found in the previous work. The previously developed procedure for the prediction of pillar life spans consequently requires no adjustment, although the error span is in the region of 20%. It is recommended to do further research into the effect of sealing of panels and, possible chemical changes taking place in the pillars as they age on the scaling rate.

Jan 1, 2004

By W. M. Deaton

[The formation of gas hydrates in natural-gas pipe lines depends on temperature and pressure conditions in the lines as well as on the presence of condensed water. The operating pressure in a pipe line may be determined easily and usually is available from the records of operation, but the temperature seldom is known. In cooperation with the American Gas Association, the Bureau of Mines, in its investigation of gas hydrates, conducted a pipe-line-temperature survey and studied underground temperatures at depths at which pipe lines ordinarily are buried and the relationship of these temperatures to prevailing atmospheric conditions. A similar but more limited study of this type was, conducted by engineers of the Bureau of Mines a number of years ago.4/A summary of the earlier findings was included in a general report by the Bureau on the flow of natural gas through high-pressure transmission lines.5/ In the present study, data on temperature variations were obtained at several places widely separated geographically. This information should assist pipe-line engineers in designing and operating natural-gas pipe lines. In the pipe-line-temperature survey here resorted, a study was made along a 22-inch natural-gas pipe line: originating near Amarillo, Tex., and extending northwestward through New Mexico into Colorado (fig. 1). Some data also were collected along a 16-inch line extending southward from Amarillo. In the study of underground temperatures and their variation with atmospheric temperature, recording; equipment was installed at the]

Jan 1, 1941

By Richard P. Reiff

"The Facility for Accelerated Service Testing (FAST) program has been involved in numerous rail wear tests since its inception in 1976. A number of specialized tools have been developed to aid in assessing specific performance parameters including gauge face wear, head height loss, metal flow, head area loss, hardness, and welded rail end batter. The layout of a test site, including position in curve, number of measurements per rail, and train operation must be properly controlled/monitored to provide valid wear comparisons.This paper will provide an overview of the above-mentioned tools and techniques. In addition, a summary of recent test results from FAST, including information on head hardened rail investigations, will be provided. A set of guidelines for establishing a revenue service field test site will also be provided to aid users in performing evaluations of their own.IntroductionBackground of Rail Wear Testing at FASTThe Facility for Accelerated Service Testing (FAST) located at the Transportation Test Center, (TIC), Pueblo, Colorado has been involved with testing of rail since program initiation in 1976. A huge data base of rail wear information has been gathered from FAST operations under a variety of rail metallurgies, lubrication conditions, and measurement techniques. Attempts at obtaining meaningful rail wear information from early (1976-1978) FAST rail wear data was hampered by two main factors: (I) measurement techniques were insufficiently accurate for the amounts of wear being experienced, and (2) the lubrication was not sufficiently controlled to obtain uniform conditions for a sufficient measurement time period.Subsequent test periods were operated with improved measurement techniques and controls that ensured statistically valid data. The policies and conditions that permit accurate rail wear assessment will be reviewed and outlined in this paper, along with some specific TIC and field examples that will allow the user to improve the accuracy of a field rail test on their own operating property."

Jan 1, 1988

By J. W. Jensen

This report was prepared as a background reference for future publica¬tions concerning the damping capacity of metals and alloys. It contains a broad description of the theory and methods of measuring damping capacity and correlates the developments of the past decade in terminology, units, and techniques. Damping-capacity instrumentation at the Mississippi Valley Experiment Station, Rolla, Mo., is described. The bibliography contains over 150 references to recent articles, each tabulated as to material investigated and test variables, such as frequency, stress, mode of vibration, and temperature. INTRODUCTION After it discovered high-damping manganese-copper alloys before World War II, the Bureau of Mines began research on the damping capacity of alloys and has continued to expand this activity to the present time. In physical metallurgy, damping capacity has become an important research tool in the Bureau. The physical measurement of the damping properties of alloys was begun at the College Park laboratories, and later conducted at Salt Lake City under the direction of Dr. E. V. Potter. Among the many articles resulting from this work, Damping Capacity of Metals (108)3/ has received frequent men¬tion in more recent literature and describes briefly the methods of measurement employed at that time.

Jan 1, 1959

By A Hoyle, P Walker, D Bennett

The Phu Kham copper-gold operation located in Laos People’s Democratic Republic (PDR) is owned and operated by Phu Bia Mining Limited. PanAust Limited, based in Brisbane Australia, holds a 90 per cent interest in Phu Bia Mining Limited, with the remaining 10 per cent held by the Government of Laos PDR.The 12Mt/y copper-gold concentrator at Phu Kham commenced production in April 2008. Flotation copper and gold recovery from commissioning was consistently poor, due to the high levels of pyrite and problematic secondary and oxide copper species and non-sulfide gangue.The low recoveries of copper and gold from Phu Kham were recognised during the feasibility study design phase. A bulk sulfide flotation regime in roughing produced high recoveries, however a large capacity cleaning circuit was required and there was risk of not meeting saleable concentrate grade specifications. The installed design offered a capital efficient compromise to ensure that a concentrate grade of 24% copper could be achieved at acceptable recoveries.Incremental improvements in copper recovery were achieved by 2011 through conversion of conditioning cells to flotation cells in both roughing and first cleaning and increased cleaner capacity through the installation of a Jameson cell. In 2012 the Phu Kham Upgrade Project was commissioned to increase mill throughput, along with additional rougher and cleaner capacity to increase residence times at the nominal 16 Mt/y throughput. The marginal reduction in primary grind size due to the additional ball milling power also provided a small recovery improvement.This paper presents the development, design, implementation, and performance of the Increased Recovery Project commissioned in April 2013 which targeted the major causes of copper loss from the circuit. Based on fundamental and detailed test work and mineralogical analysis of concentrator streams, an optimised design was developed which has increased copper and gold recoveries by over 5% and 10% respectively. The Increased Recovery Project has positioned the concentrator to process high pyrite ores that were previously considered untreatable, and opened further opportunities for maximising flotation recovery by de-bottlenecking plant regrind and cleaning capacity.CITATION:Hoyle, A, Bennett, D and Walker, P, 2015. The increased recovery project at the Phu Kham copper-gold operation, Laos PDR, in Proceedings MetPlant 2015, pp 246–265 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

Continuously monitor and record respirable dust levels underground by a reliable, sensitive, and fast-response device. Approach A light-scattering photometer, having a LED (Light Emitting Diode) light source and other significant improvements, has been designed and incorporated into a portable continuous monitor. How It Works The monitor continuously draws air into the sampling inlet through a cyclone that removes dust particles larger than respirable size. The dusty air enters the photometer vertically downward through a cylinder which is intersected by the optical system. (This cylinder appears as a circle in the drawing of the photometer.) The center of he column of dusty air intersects a beam of pulsing light from the LED, causing some of the light to be reflected, scattered, and refracted. Only the light that is scattered at an angle of about 700 from the light beam passes through a lens to the photodetector which generates an output voltage Signal proportional to the dust content in the air. This signal is detected, amplified, and converted to a digital readout directly in milligrams of dust per

Jan 1, 1979

By Robin J. Batterham

We still need to innovate, but it is getting harder. The real price of metals is declining, return on shareholder value is lower than other industries, and there is a shorter-term focus on staying viable in a capital-intensive industry where timeframes for implementation of new technologies can be long (+I5 years). In this environment, the levels of R&D spent by major minerals companies are remaining steady at around 0.2%-0.5% of revenue. This is not large and to remain viable in the future, we need to be smarter about the way in which we do R&D. The mining industry is a knowledge-based industry. Driving down the cost curve demands innovation, which demands knowledge. To be smarter and more effective in our approach to innovation, a new paradigm is required Generating, capturing and using knowledge has evolved from Mode 1 (discipline based and clear distinction between basic and applied research) to Mode 2 (multidisciplinary, team-based approached with flow between basic and applied activities). Mode 2 is now seen to be much more efficient and to deliver better appropriability (Tegart 2003). To survive, we need to innovate, and the best way to do this is collaboratively. Some examples and pointers for the future will be given in this paper. THE CURRENT SITUATION The Rand report and other recent studies have painted a grim outlook for the mining industry. The real price of metals continues to decline (Figure 1) and profit margins remain thin. This is reflected in shareholder returnwhich are well below other industries (Figure 2)-and current management strategies-which reflect something of a "survival mode." The current focus for most mining companies is on short-term, incremental gains

Jan 1, 2004

By Ian Vaz, Takefumi Takuma

"The New Orleans area has been repeatedly flooded by major storms and hurricanes since its French colonial era. After severe flooding in May 1995, the U.S. Congress authorized a massive flood protection project called the Southeast Louisiana Urban Flood Control Program (SELA) in 1996 to improve interior drainage in Orleans, Jefferson, and St. Tammany parishes. However, the project was not fully funded before the landing of Hurricane Katrina in 2005 and Hurricane Rita, which breached many of the area’s levees and flooded 80 percent of the city. Finally, the project was fully funded in 2008 and has been worked on towards its 2017 completion. Another large project simultaneously worked on in the area is the Hurricane and Storm Damage Risk Reduction System (HSDRRS). This system was designed for a 100-year level of flood risk reduction. One particular project within the HSDRRS rendered successful due to an unconventional method of pile driving that was utilized to install sheet piles to reinforce an existing concrete I-wall. This paper will discuss how and why this non-vibratory method of sheet pile installation allowed the project to be successfully completed ahead of schedule.INTRODUCTIONSteel sheet piles were utilized on many of the SELA and HSDRRS projects for permanent cutoff walls under concrete I-walls or T-walls or for temporary earth retaining walls of drainage structures. Although the SELA Project was established in 1996 after severe flooding the year before, hardly any work was done on it until the two catastrophic storms Hurricanes known as Katrina and Rita triggered its revival. These two hurricanes also triggered the HSDRRS soon after the storms’ devastation. The SELA project authorized to improve interior drainage systems while the HSDRRS project was authorized to raise or restore levees and floodwalls mainly along Lake Pontchartrain, the Mississippi River, and Lake Borgne in addition to other areas. Figure 1 shows the SELA Projects that have been completed, are still under construction, or approved for construction. The projects fully highlighted in yellow within the map specified the press-in piling method. These improvements included drainage systems, pump stations, surge walls, and outfall canals as enhanced protection for future storms similar to Hurricane Katrina that caused so much damage by inundating the New Orleans area in August and September 2005 respectively (Facts and Figures, 2012). The completion of these projects were the responsibility of the U.S. Army Corps of Engineers, New Orleans District.Due to the fact that many of the projects were in densely populated areas, the Army Corps of Engineers specified a non-impact, non-vibratory press-in piling method for driving and extracting sheet piles for many of the projects to mitigate noise and vibration impacts. The soft soil conditions in the New Orleans area was also a contributing factor in the Army Corps of Engineers’ decision to specify this piling method due to the risk of settlement for existing historical as well as modern structures. In addition, there were other projects that elected to use the press-in method without any contractual requirements. One of these projects was the Inner Harbor Navigational Canal Reach II Emergency Interim Repair which was part of the HSDRRS project that has been under construction since its authorization in 2005 (Facts and Figures, 2012)."

Jan 1, 2017

By Martin B. Hudson, Daniel Brescia, Zhangwei Ning

Due to the complexity and sensitivity of surrounding environments, instrumentation and monitoring (I&M) is critical for many urban deep excavations. The objects to be monitored include shoring bulkheads, retained embankments, adjacent buildings and roads as well as underground utilities. However, there are also plenty of constraints on the implementation of I&M such as: congested site space, difficult access to instruments, coordination among multiple contractors, and installation permits for private or public properties. Because of these constraints, sometimes the implementation of the initially planned I&M is delayed, its scope is reduced, and/or the continuity of monitoring is interrupted. For these reasons, it is important to implement the I&M with robust and redundant capabilities while providing minimal interference to the project construction and schedule. This paper describes state-of-the-art I&M technologies including automatic motorized total station (AMTS) with camera and automatic leveling device, reflectorless AMTS and IoT- based wireless sensors based on a case study of an on-going deep excavation project. INTRODUCTION In urban environments, deep excavations requiring the construction of temporary shoring bulkheads are becoming increasingly common, with the associated need to provide protection of the surrounding built environment during construction. Protection of the surrounding environment requires planning, engineering, construction, monitoring, and excessive shoring movement mitigation. The I&M is a vital component of the deep shoring implementation. In public projects, geotechnical I&M is often placed within the general contractor’s scope, whereas the majority of deep excavations are privately undertaken. For those private developments, sometimes the developer contracts the geotechnical I&M directly with the project geotechnical engineer or by a geotechnical I&M specialist hired by the project geotechnical engineer. In either the public project or private development case, the effective deployment of the I&M system relies heavily on coordination and collaboration with the project contractor.

Jan 1, 2018

By Seffen Leppla, Rolf Katzenbach, Matthias Seip

"Abstract The economic and safe design of deep foundation systems in difficult soil conditions is based on a reduction of construction material used, construction time spent, energy consumed and a high-level modelling of the soil-structure-interaction. The special foundation system Combined Pile- Raft Foundation (CPRF), in-situ load tests on the construction site and a sufficient soil investigation allow cost optimised constructions. In any case at challenging projects the observational method has to be applied for verification and quality control of the design. Regarding the 4-Eye-Principle as basis of the quality control management an independent peer review of the planning, design and construction phases is the guarantee for safety, serviceability and optimisation of all projects. Main execution standards for the construction of deep foundations based on the Eurocode 7 are summarised and discussed. The paper presents the basics of the safe and qualified design and construction of foundation systems including quality assurance. The application in engineering practice is shown on achallenging project of high-rise buildings with difficult boundary conditions.IntroductionThe construction of deep foundation elements in inner cities are special challenges due to the limited space for the construction works and the effects on existing buildings (Figure 1).An economic and safe design of deep foundation systems in difficult soil conditions is based on the following main aspects:•,qualified experts for planning, design and construction•,interaction between architects, structural engineers and geotechnical engineers•,adequate soil investigation•,design of deep foundation systems using the Finite-Element-Method (FEM) in combination with•,enhanced in-situ load tests for calibrating the soil parameters used in the numerical simulations•,quality assurance by an independent peer review process (4-eye-principle) combined with theobservational method if necessary"

Jan 1, 2014

By C. Hellar

A new dual-boom remotely controlled roof bolter was designed, fabricated, and then tested in an underground coal mine. Remote-control functions allowed complete bolting cycles to be performed on two booms with both operators located within protective cabs. Capabilities included 3-to 6-foot-long bolts in 5-to 8-foot seams, limited to bolts 20 inches shorter than seam height. Machine was in compliance with all regulations including dust collection, machine lighting, and permissibility.

Jan 1, 1979