Search Documents

By J. A. López-Molina, S. García, V. Castellanos-Pedroza

"Grouting aims to reduce the permeability of rock mass below a predetermined value and has been widely used in rock engineering field for a long time. However, the injection procedure needs several empirical decision makings and it is rather difficult to reliably confirm the achievement of improvement, because the grout penetration process is not sufficiently clarified. This investigation proposes a neuronal method of defining spatial distribution of rock hydraulic properties and a fuzzy scheme for estimating their relation with the grout penetration (consumption, localization and filling material). The intelligent method stands as a tool for helping in harmonizing the sealing activities and the medium conditions. The virtual simulation of grouting strategies embraces geology, hydraulic and rock characteristics and the filling process. Important aspects as different pressure injection levels and fracturing systems can be holistically studied using the intelligent environment, resulting in an advantageous, economic, flexible and interactive tool for planning better this critical activity.INTRODUCTION Grouting is a very common method of sealing rock and repairing concrete structures (Butron et al., 2010) and its use in engineering of dam-foundation and tunneling has been documented as very successful (Yang, 2004). Generally speaking, to achieve the closing purpose, boreholes are drilled into the rock mass and grout is injected (under pre-selected pressure) until the fractures around the borehole are filled. The complete filling of these fractures is possible if they are connected to each other in such a way that the remaining water and air can be displaced outside the designed grouting zone (Houlsby, 1990; Kutzner, 1996). Water testing is necessary for evaluating seepage potential and for determining whether grouting is necessary or practical. Regardless of the main reason for the investigations, design of a program for water testing for grouting should consider the type of structure to be built, the geologic conditions at the site and the level of seepage control desired. As information gathered the report must content the fracture openness, number and connectivity, exploratory drill holes orientations, materials situation and a panorama of rock-mass state (quality)."

Jan 1, 2015

By Nicholas R. Dixon

This report summarizes all work performed under Phases I, II and III of U.S. Bureau of Mines Contract H0387006, "Development of a Prototype Retrofit Noise Control Treatment for Jumbo Drills." The noise and vibration levels of four jumbo drills were characterized and a survey of percussive rock drill usage is reported. A Gardner-Denver DH 123 drill was chosen as a demonstration drill, and extensive noise diagnostic studies were performed. Noise control treatments were designed, developed and evaluated in a reverberant drill test facility. The treatments consisted of an integral enclosure/muffler for the drifter, vibration isolation of the drifter from the enclosure and feed, and a drill steel sheath. A 19 dBA reduction in overall sound power level was achieved with no loss in drilling rate. The prototype retrofit treatments were field tested in an aboveground mine and in a production section of an underground zinc mine. Long-term durability and operator acceptance of the enclosure/muffler treatment were excellent. Preliminary evaluation of the drill steel sheath was encouraging, although additional testing is required.

Jan 1, 1982

By G. R. Addie

"In February, 1975, the President of Georgia Iron Works Company, Mr. Tom Hagler decided to build a new hydraulic laboratory to water performance test all of the companies' centrifugal slurry pumps.Equipment procurement started in March, 1975, by ordering of a mini computer data acquisition system.Work commenced on the lab in July, 1976, by erection of a Butler Building and the laying down of a 20,000 gallon concrete sump.By late October, a facility compromising two water test loops of 8"" and 18"" pipe diameter was in operation carrying out head quantity and suction performance tests on pumps up to 16"" in size.In August of the following year, an 8"" diameter pipe slurry loop was installed to enable pipe friction and deposition velocity of a slurry to be measured in an 8"" inside diameter pipe.With the encouragement of Reserve Mining in Minnesota and IMCC in Florida, this was followed in March, 1978, by the addition of over 300 feet of 18"" diameter pipe to make up an 18"" diameter pipe slurry system complete with head loss and deposition velocity observation sections.The office and shop areas of the lab were again expanded in April, 1978, to provide further expansion to the test sections and staff facilities."

Jan 1, 1980

Three methods of gold analysis are briefly described highlighting some of the problems and advantages of each. The variation of results between samples and splits and due to method of preparation is illustrated. The mean per cent difference of the fire assay values from the means of sample split values for three cases is 15 per cent.Finally, a comparison of the aqua regia leach atomic absorption spectroscopy (AAS) and fire assay fusion AAS techniques is made.This shows that the mean precision, the ability to obtain the same value, of the methods at 98 per cent confidence is ± 30 per cent and ± 15 per cent respectively. The fire assay fusion AAS method is relatively more accurate than the aqua regia one.

Jan 1, 1984

By Thomas J. Witzig

This Bureau of Mines report is a background study of the International Tin Agreement. Attempts at stabilizing the tin market prior to the agreement are detailed, as well as the conditions and negotiations that set up the agreement. Details of the five consecutive 5-year agreements beginning in 1956 are presented, with emphasis on membership and the agreements' primary tools: the buffer stock and export controls, Attention is focused throughout on the United States activities during the period, especially with regard to its strategic stockpile, and its involvement with the agreement culminating in its membership, for the first time, in the fifth agreement beginning in 1976. Considerations leading to the U.S. decision to join are detailed, and U.S. activities in the negotiations for the sixth agreement are presented. The status and outlook for the agreement are discussed, and evaluations of the effectiveness of the agreement and its components are reviewed.

Jan 1, 1981

By Othon do Rêgo Monteiro Neto

[The present study has investigated the extraction of copper from a chalcopyrite flotation concentrate using an adapted strain of Thiobacillus ferrooxidans and shake flasks, tank leaching and Warburg respirometer techniques. From the shake flask experiments, the activation energy and the frequency factor have been determined to be ?ka = 59.4 kJ and A = 3.3 x 105 S-1, respectively. The temperature coefficient was found to be Q10 = 2.2 in the range of 20 to 35°C. It was suggested that the reaction mechanism of chalcopyrite leaching by T. ferrooxidans involves the formation of an activated complex. whose thermodynamic values have been calculated to be ?G? = 92.1 kJ, ?S? -148.8 J K-1 and ?H$ = 47.8 kJ. The maximum volumetric oxygen mass transfer coefficient for the reactor leaching was found to be achieved by using an optimum air flow rate of 1970 cm min l at a rotational frequency of 1000 min-1. The highest copper extraction in tank (reactor) leaching experiment was 86.8% after 17 days of leaching, while in the sterile runs the corresponding copper extraction was only 40.1%. The copper extraction was suggested to be diffusion controlled. The power requirement of the aerated reactor was calculated to be Pg = 2.02 watts. During leaching, the oxygen saturation concentration was found to be C* = 6.70 mg dm-3. Using the gassing out method the critical oxygen concentration was assessed to be CCrit 0.05 mg dm 3. From the Warburg experiments, the kinetic parameters of the Monad equation were derived with a new evaluation technique to be Vmsp = 9.0 µm3 02 min-1 mg protein-1 and K = 7.4% pulp density for the effect of substrate concentration. The order of reaction and the overall reaction rate constant were determined from the modified van't Hoff plot to be n = 0.0 and k = 1.49 p dm3 02 min-1 mg Protein -1 for the chalcopyrite concentrate oxidation by T. ferrooxidans. On the basis of this experimental work, a preliminary flow sheet has been proposed for the bioextraction of copper from flotation concentrates.]

Jan 1, 1985

Within CRLÆs lifetime there have been a number of products that have proceeded through their life cycles. In each case market forces and technological advances have forced the cessation of the product. The company has then had to develop alternative outlets for its copper. Sometimes it has produced a similar product to fill the same market. In other cases the extra copper is sold as cathode. Today, CRL produces no semi-fabricated copper products and all cathode is sold. More recently, CRL has ventured into the sale of technology and manufacture of cathode motherplates. This area, whilst it is not what had been a traditional area of core business, has been found to be profitable.

Jan 1, 1998

By Mark Sanders

This report compares a proposed 10/60 "piggyback" 02 generating self-rescue unit to the standard CO self-rescue unit with respect to work task interference. A simulated low seam coal mine was constructed and subjects performed locomotion, shoveling, cart pushing, and timbering tasks with the 10/60 or self-rescuer attached to their belts. Task completion time was longer on all tasks when wearing the 10/60 unit, although only locomotion was statistically significant. The 10/60 unit was bumped over 100% more often than the standard self-rescuer. Implications for design of the proposed 10/60 container are: 1) unit?s container must be extra durable to withstand the added abuse it is likely to receive by low coal miners; and 2) extra consideration must be given to preventing the device from slipping on the belt while working, especially in low coal.

Jan 1, 1980

By R. J. Forzatti

The production of sulphuric acid from sulphur generates heat. The majority of this heat is recovered as steam and is often used to generate electricity. Heat not recovered as steam is rejected to cooling water systems. The design of the turbine, condenser, and cooling water systems impacts the overall water, energy, and environmental footprint of the plant. This review considers a conceptual 2000 t/d sulphuric acid plant with several alternative cooling water systems. The review utilizes Hatch?s 4 Quadrant sustainable design tool to compare the alternatives on both an economic and a weighted sustainability scale.

Jan 1, 2014

By M. Felsenthal

Engineers are frequently faced with the problem of having to predict oil recovery from a solution gas drive reservoir in the early life of a field. This is often the time when actual laboratory or field-derived gas-oil permeability (kg/k0) data are not yet available. Although excellent collections of k0/k0 data for various types of rocks may be found in the literature,1,2,3 a need exists for a more detailed correlation of k0/k0 data with core properties such as porosity, permeability, clay content or pore-size distribution. It is the purpose of this article to present this type of correlation for sandstone material. The correlation is based on laboratory tests performed on over 300 core samples from 19 reservoirs in the United States and Canada. EXPERIMENTAL Cores were analyzed by routine procedures, using samples of conventional size (7/8-in. diameter, 7/8-in long) cut parallel to the bedding planes. Air permeability was measured at 1.67 atm mean pressure in a Hassler-type apparatus. Porosity was determined with the aid of a Ruska bulk volume meter and a Boyle's Law rock volume meter, An evaporation method' was used to evaluate irreducible water saturations. Core samples were saturated with 25,000 ppm NaCl brine. The brine was reduced to the irreducible saturation, and the remainder of the pore space was filled with kerosene. This was followed by multiphase flow tests using the so-called "dispersed feed" technique.5 n this technique, gas and oil (kerosene and kerosene-saturated air) were dispersed with the aid of a porous Alun-durn feed head, the face of which contained a waffle-shaped system of Lucite-lined grooves. Oil entered the back side of the feed head and emerged at the raised areas of the front face. Gas was introduced directly into the system of grooves at the front face. The gas-oil mixture then entered the test core which was kept in capillary contact with the feed head. Permeabilities were determined from rate and pressure measurements and saturations from weights. All determinations were performed at equilibrium or steady-state conditions. Pore-size distributions were determined on selected samples by a mercury injection technique.6 GENERAL CORRELATIVE TRENDS When examining data from a given reservoir, it was noted that k0/k0 vs saturation curves became generally less steep as specific air permeability increased, a development that has a favorable effect on oil displacement efficiency by solution gas drive. This trend has also been reported by others in the literature.' An effect of porosity on k0/k0 data was also noted. This effect was not generally discernible in a study of relative permeability data for a given reservoir but became apparent when data for sandstone reservoirs of similar lithology but differing average porosity were compared. For instance, in a comparison of argillaceous and/or calcareous sandstones from 11 reservoirs ranging in average porosities from 14 to 28 per cent, a definite trend was noted, indicating that for a given permeability k0/k0 curves became less favorable (i.e., steeper) as porosity increased. A similar trend was observed for a group of comparatively clean sandstones from five reservoirs ranging in average porosities from 15 to 21 per cent. For a given permeability and porosity, comparatively clean sandstones gave more favorable k0/k0 curves than argillaceous and/or calcareous sandstone or chert reservoirs. The laboratory studies also showed that least favorable k0/k0 curves were exhibited by shaly sandstone, conglomerate, and sandstone containing carbon inclusions. Table 1 lists the various source reservoirs classified by lithology types. To facilitate a correlation of k0/k0 data with core characteristcis, it was found expedient to work with

By Michael Bayerl

The HILTI OneStep rockbolt was implemented for roadway development in German deep coal mines in 2004. The development by HILTI Company is based on a technical joint venture with RAG Deutsche Steinkohle AG. The technical development of a One-Step bolting system was required for weak strata conditions at the roadway development face. Standard resin bolting has reached the limit of performance when boreholes are squeezed and cannot be filled with capsules. In some cases the heading face is brittle and requires additional support for installation of the bolts and a person working immediately next to the borehole. The Hilti One-Step system allows automated and safe processing at the heading front and provides the key technique to avoid these problems.

Jan 1, 2009

By Orr C. W

Continuing the systematic investigation of the influence of elements on the properties of lead(1). If the effects of additions of copper (up to 0.3%) on Port Pirie lead have now been determined in so far as creep rate is concerned.The results in the present paper contain also a survey of the influence of copper on the micro-structure of lead, a feature which has not appeared in the previous papers of this series. Further, it has now become known that creep is but little related to the more usually determined properties such as hardness and tensile strength. Since, however, these properties are of considerable importance in connection with the fabrication and use of this metal. Brinell hardness determinations have also been made and are here included.It is becoming more and more realised also that to be useful, creep data should refer to stresses of the order of those used in practice. This is due to the fact that as soon as deformation takes place, the properties of the metal are automatically changed. Lead does, of course, creep during industrial use, and probably (in lead chamber construction for example) extensions of the order of 5%...

Jan 1, 1938

By S. C. Richardson

The electrowinning (EW) circuit involves using DC current in the electro-deposition of metal ions dissolved in an electrolyte solution. This paper reviews a method to generate an electrical model of an EW circuit and the resulting DC current flow and voltage distribution within the circuit. Topics include: calculations of electrolyte conductivity and the equivalent electrical resistance of the electrolyte within the electrolyte pipelines connected to the EW circuit; the breakdown and classification of the EW cell voltage into thermodynamic and ohmic potentials; methods to calculate current flow and voltage distribution throughout the EW circuit; and the development of an interactive visual computer model to simulate an actual EW circuit. Stray current can pose an electrical shock hazard to employees in electrolytic tankhouses. Increased awareness and understanding of the voltage distribution and potential stray current in an EW circuit can help mitigate the risk of tankhouse workers becoming exposed to electrical shock hazards. INTRODUCTION Copper electrowinning tankhouses include rectifiers that deliver large amount of DC current to a series of electrolytic cells consisting of electrolyte solution and electrode pairs. The design also includes metallic conductors in the circuit which include the rectifier’s positive and negative busbar, inter-cell busbar, and the anode and cathode frames. The electrolyte acts as an electrical conductor that transfers current via ions between the anodic and cathodic electrodes within the cell. Electrolyte, as a conductor, is also capable of conducting DC current outside the main EW circuit through the connected electrolyte feed and return pipe systems. DC current that follows a path other than the intended path through the series of electrolytic cells is referred to as “stray current”. Developing an electrical model enhances understanding of voltage distribution and current flow in an EW circuit. This paper discusses the derivation of the various representative components of the model as well as the output from the model. An interactive visual computer simulation incorporates the model output in order to aid in the understanding of voltage distribution and current flow throughout the EW circuit.

Jan 1, 2019

By James Ridenour

This report represents the first comprehensive accounting of lode mining sites in the Loon Creek mining district, Custer County, Idaho. Thirty-five mine and prospect locations have been added to the Bureau's Mineral Industry Location Subsystem (MILS) data base as a result of initial phases of a mineral appraisal of the River of No Return Wilderness; previously known locations were field checked and the updated information added to the data base. The district's major deposits are gold-copper-silver fissure-fillings hosted by biotite schist intruded by dikes ranging in composition from rhyolite to lamprophyre. These deposits contain a trace element suite similar to Tertiary pink granites and may be related to intrusion of the nearby Casto pluton. Continued firm gold prices could stimulate the search for precious metal occurrences in this and other mining districts in central Idaho.

Jan 1, 1983

By J. Frostiak

"This paper describes some energy reduction measures Implemented at the Griffith Mine. Before proceeding, I will give you a brief overview of the operation.The Griffith Mine is an iron ore mining, concentrating and Pelletizing complex located in the red lake area of northwestern Ontario. The operation is owned by Stelco Inc. And is managed By Pickands Mather & Co. of Cleveland, Ohio. Operation of the concentrator commenced in 1968 and it has been producing at a nominal capacity of 1,500 ,000 tons annually.The plant flow sheet is illustrated in this slide. Run of the mine ore is crushed in a single stage 54"" gyratory crusher. Reclaim ore feeders draw from an open stockpile to feed two 32' diameter by 12' long autogenous mills, each driven by 6800 hp. Two s·rages of wet magnetic separation, roughers and cleaners, and primary cyclones complete the primary circuit. Cleaner concentrate is then ground in four 14' diameter by 28' long pebble mills rated at 2000 hp. The secondary grinding circuit is closed by cyclones and fine screens. Secondary cyclone overflow is further upgraded through hydro-separators, finisher magnetic separators and flotation.The magnetic concentrate produced is then thickened, filtered, balled and fired in three vertical shaft furnaces to produce a high quality hematite pellet."

Jan 1, 1983

By Jared M. Green

This paper presents the wall stabilization design and implementation for a 541 linear ft masonry and concrete gravity-type retaining wall flanking the west perimeter of a 7.37 acre parcel in Bronx, New York. This paper will discuss the results of static and dynamic stability analyses performed for the pre- and post excavation phases for the proposed 300 ft wide open-cut of up to 14 ft of contaminated soil below the toe of the retaining wall. The wall stabilization consisted of over 74 inclined drilled and grouted anchor dowels, and 55 tiebacks drilled and grouted to the underlying mica schist bedrock. Three over-lapping rows of jet grout columns were chosen as the foundation solution for the existing retaining wall. This paper focuses on the design, construction and performance of the jet grout curtain wall. The jet grout wall served three purposes: 1) underpinning and excavation support for the removal of contaminated site soils, 2) permanent hydraulic barrier, and 3) resistance against a deep seated failure within the thick clay layer present at the site. The originally designed jet grout wall had unexpected negative effects to the existing retaining wall. The jet grouting program was modified while the Observational Method (Peck 1969) was employed to keep wall movements to a minimum. This paper discusses the diagnostic methods used to determine the cause of retaining wall movement; the implementation of a remedial ground improvement program; the modification to the jet grout installation procedure; and the ultimate performance of the jet grout wall.

Jan 1, 2011

By J. H. Zietsman, M. W. Erwee, P. J. A. Bezuidenhout, Q. G. Reynolds

"Pyrometallurgical furnaces are tapped through tap-holes that are opened with drills and oxygen lances. The lance is often used on its own or as the last step of opening the tap-hole. Interaction of oxygen with molten material inside the tap-hole can occur, and is a phenomenon that is not well understood. As part of a study that focuses on the effect of lancing on flow inside and around the furnace tap-hole, a cold-model validation was done. The validation study focuses on validating the MULTIPHASEINTERFOAM multiphase flow solver in OpenFOAM® for the problem involved. The sensitivity of the model to different materials properties (viscosity and density in particular) is presented with both cold models and the results from flow simulations in OpenFOAM®. IntroductionMany pyrometallurgical operations are carried out in furnaces where molten material accumulates continuously. Once enough material has accumulated and is ready to be removed from the furnace, material is tapped through one or more tap-holes in the furnace. Tap-holes differ significantly in both geometry and materials of construction, depending on the process involved – examples of different types of tap-hole configurations can be found in, for example, Nelson and Hundermark (2014). Tapholes all share one common feature: they are high, wear areas of the furnace. Molten material at high temperature flows through these areas, after which the tap-hole is sealed, usually using tap-hole clay. The purpose of the tap-hole clay is to harden inside the tap-hole and seal it until the next tap.Once ready to tap, a pneumatic drill and/or oxygen lance is used to open the tap-hole. The extent of lancing a furnace tap-hole depends strongly on the type of furnace. In, for example, many blast furnace operations lancing is limited as much as possible, and done only if drilling was not effective. In other operations, such as on small-scale pilot furnaces with short tap-holes, only lancing is used to open the tap-hole."

Jun 1, 2019

By Wilbur I. Duvall

This report presents experimental data on crater formation in four rock types. From an analysis of these data a general theory of rock breakage by explosives is deduced. This theory accounts for most of the rock breakage and other phenomena that occur when a concentrated charge is detonated in a drill hole near a free surface. From instrumented crater tests and high-speed motion pictures of the explosions, various experimental checks on the deduced theory of rock breakage are made. The general mechanism of rock breakage by explosives as described in this report is outlined briefly below. The detonation of the explosive charge creates a high gas pressure in the charge hole, which in turn generates a compressive strain pulse in the surrounding rock. This compressive strain pulse travels outward in all directions from the charge hole. Near the charge hole the amplitude of this strain pulse is sufficient to cause crushing of the rock. However, as the strain pulse travels outward its amplitude decays rapidly until no further crushing of the rock is possible. The compressive strain pulse continues to travel outward until it is reflected by a free surface. Upon reflection the compressive strain pulse becomes a tensile strain pulse. As the strength of rock in tension is much less than in compression, the reflected tensile strain pulse is able to break the rock in tension, progressing from the free surface back toward the shot point. In other words, the rock is pulled apart, not pushed apart.

Jan 1, 1957

The mining industry is generally regarded as a high risk industry, mainly because of the difficulties in estimating the tonnage and grade of mineral resources, the fluctuations in metal prices, mining problems and other problems which occur with mining in offshore and remote locations, such as appropriation or disruption to supply. As a consequence, finance providers require a high reward from mining projects. In the past two decades, the development of "mega" projects has led to the packaging of the finance becoming more sophisticated. Some would see this move as a measure of the evolution of banking rather than an intrinsic facet of mining finance itself. Project financial managers now require a thorough knowledge of all the financial tools which are available and have to be aware of the funding options so that they can put together a finance package which minimises the cost of the financing with the risk spread adequately between the partners of the financing. The different sources and types of finance for mining projects are described herein along with the factors which determine their costs. To understand the ramifications of financing mining projects, it is essential to appreciate the fundamental difference between debt and equity, which illustrates the importance of gearing. Costs of finance are determined by the interaction of supply and demand forces. Bankers and other financiers have become more adept at isolating a wide selection of risk elements and have devised a formidable range of insurance mechanisms. There is still a lot of money looking for good project risks and if a good project is properly presented and structured, financing can be obtained in today's market.

Jan 1, 1990

By Shigeru Nishitake

The Earth Pressure Balanced (EPB) shields designed by Mitsubishi Heavy Industries, Ltd., are recently more enthusiastically accepted by tunnel boring specialists. This company having built 1,000 tunnel shields utilizes its vast experience to resolve the problem to excavate through big boulders scattered in rather soft alluvial soil. Several types of EPB shields which can cope with large size boulders are described. Such shields are equipped with both drag bits and rolling disc cutters on the cutterheads. Previously removal of boulders has presented safety problems for workers while in the muck chamber, or venturing in front of the shield. This report describes the problem and how the equipment was modified to deal with the problem.

Jan 1, 1987