Search Documents

By Penrose E. K

With the exception of occasional periods, when up to 80% of oxidized ore was treated, the G.M.K. plant treated all sulphide ore until October, 1939. The treatment was, briefly, as follows:The ore was ground to approximately 17% plus 200 mesh Tyler and agitated in cyanide solution, after straking. After agitation, the pulp passed through two stages of counter-current decantation washing in Dorr thickeners and was filtered once, to complete the precyanidation stage.The precyanide filter cake was repulped with flotation circuit solution and floated in a Denver Sub A flotation machine, consisting of twelve cells. The concentrates were roasted, cyanided and filtered four times before disposal to the' dam. The flotation tailings were thickened to conserve water and pumped away to a separate dam.The average results of flotation operations for the six months before October, 1939, are shown in Table 1.

Jan 1, 1942

By D. C. Panigrahi

Extensive field studies have been carried out to investigate the pillar fire problems in one coal mine in India. A Thermal IR gun and a Thermovision camera have been employed for thermal scanning to assess the state of heating in selected pillars. Special sampling set-ups have been designed to collect gas samples from the holes drilled into the selected pillars and the multigas detector is used to analyse the composition of samples in situ. In order to predict the spontaneous heating in coal pillars, different gas ratios have been calculated and it has been observed that some of the established gas ratios, viz. Graham?s ratio, Young?s ratio etc. have resulted in negative values in samples containing high amounts of methane. The modified gas ratios have been proposed which will be useful for predicting the pillar fires. These ratios may also be used for assessing the condition of fires in sealed-off areas.

Jan 1, 2004

By E. T. Turkdogan

Jan 1, 1962

By M. Kalin

"SUMMARYWaste management in general, and the water treatment of mine and mill effluents, has become an ever increasing burden for mining operations. A reduction in these expenditures would undoubtedly be desirable if this could in fact be achieved within effluent guidelines and monitoring requirements.A brief summary is presented of the research which has as its aim the development of methods which would reduce such costs and lead to solutions for environmentally acceptable close-out conditions for acid generating mine waters. The basic concepts of Ecological Engineering and Biological Polishing are presented, together with an indication of the present state of these research efforts. Details are provided of the progress of various experiments which aim to promote reducing conditions, organic matter production and the establishment of biological filters which remove metals from the water which are then retained within the waste management areas. These conditions should lead to a curtailment of acid drainage and an improvement in effluent quality.A description is provided of the first pilot demonstration using this approach to achieve a walk-away condition for the close-out of a massive sulphide tailings resulting from 10 years of operating a copper/zinc concentrator in Northern Ontario.1.0 INTRODUCTION1.1 Waste management and close-outIt is recognized that the achievement of a cost-effective and competitive mining operation, from the commencement of exploration for ore bodies through to the day-to-day efficient operation of the mine, requires a certain expertise and sophistication. However, the environmental effects of these activities are considered peripheral issues and their importance as an integral part of the planning and development of the mine/mill, is not always appreciated."

Jan 1, 1988

That electricity is an important and valuable agent, the limit of whose capacity for utilisation is as yet unknown, is a truism; although enormous advances have been made, the possible developments are yet greater. Mining, along with other industries, shares already to a large extent in the practical utilisation of this agent. Electrical engineers have been employed for several years past in developing and applying electricity to all classes of machinery, and for every purpose where power is required and in no instance, that the writer is aware of, has its use been curtailed in favour of any other agency now known, while extensions are continually made. The first modern electric motor was shown at the Vienna Exhibition of 1873, and it was used to work a pump through a mile length of cable but it was not before 1878, that an electric motor was put into daily commercial use by Messrs. Chretian and Felix to work a beet sugar hoist. This early plant effected a saving of 40 % as compared with hand work.In 1879, the first Electric Railway was constructed for the Berlin Exhibition, and in the same year, Mr. T. A. Edison was running an experimental line at Menlo Park. The first electric line opened for the public, was constructed by Siemens and Halske, in 1881, at Lichtenfelde, and was 11 miles in length.

In considering the preparation of any paper concerning bearing metals, one feels a certain amount of diffidence in venturing into a field which has been capably explored at great length and in great detail during recent years. Many excellent articles have appeared in technical literature, dealing with the general theory of bearings and of bearing metals, the properties of white metals of the tin-base and lead-base types, and of the recently developed lead-bronzes.The justification for this further excursion into the field lies in the fact that it treats a branch of the bearing metal family which has so far received very little attention, and that of a somewhat sketchy nature, in published papers.The author's object is to give some outline of the history, development, present status and possibilities of the cadmium-base bearing metal alloys, particularly those in which copper is the main alloying element.GENERAL CONSIDERATIONS.It is desirable that attention should first of all be given to the general theory, constitution, and necessary attributes of bearing metals, in order that some of the problems met with during the development work may be better appreciated.Despite some evidence to the contrary, it is fairly generally maintained that an alloy for bearing metal use should be of a heterogeneous nature. It should consist of particles of a hard constituent uniformly distributed through a softer matrix.The basic idea is that the hard constituent should actually bear the load and resist wear, while the matrix imparts the necessary ductility and allows the bearing to align itself on the shaft in service.

Jan 1, 1934

By Gary A. Kingston

Low-cost hydroelectric energy in the Pacific Nortnwest has been an important factor in the development of a ferroalloy industry. Eleven companies, employing approximately 1,000 persons, produce about 116,000 tons (1954-58 average) annually of ferrosilicon, ferrochromium, ferromanganese, ferrophosphorus, silicomanganese, and ferronickel. About 7,500 tons (1954-58 average) of these ferroalloys is consumed in the Pacific Northwest States of Washington and Oregon; the rest is used principally in other western and mid-western markets. In 1959, the Bureau of Mines began a study to determine the current status and to evaluate the potential of the ferroalloy industry in the Pacific Northwest. The Bureau gathered information from operating alloy plants in Oregon, Washington, Idaho, and Montana; from published materials; and from consumers of ferroalloys.

Jan 1, 1962

"The McArthur River uranium deposit is the single richest uranium ore body developed in the world to date. The ore body’s average grade is 15% U3O8. Proven reserves are in excess of 450 million pounds. The grinding circuit is located underground. The ground ore is pumped to a surface facility where the slurry is thickened and loaded into containers for shipping to the Key Lake mill 78 kilometers to the south.The paper will briefly describe the mining method employed. The underground ore handling and grinding circuit, and surface facilities including slurry load out, wastewater treatment and the freeze plant will be described in detail. The paper will emphasize radiation and safety procedures that are followed to minimize operator exposure to radiation risks.LOCATIONThe McArthur River mine is located 78 kilometres north of the Key Lake mill. It is located at latitude 57’ N in northern Saskatchewan, within the southern boundary of the Athabasca formation. The nearest town is Pinehouse, located 320 kilometres to the south. Access to the mine is by an all weather road and by a private airstrip.HISTORYThe McArthur River Operation is jointly owned by Cameco Corporation (69.805%) and Cogema Resources Inc. (30.195%). Exploration for uranium in the McArthur River area started in 1980 by the Saskatchewan Mining Development Corporation, a predecessor company of Cameco.In 1984, a 12-kilometre long basement conductor was identified at a depth exceeding 500 metres. Systematic exploration drilling of this conductor resulted in the discovery of the P2 North deposit. Subsequent surface drilling programs from 1989 to 1992 delineated a narrow ore zone over a strike length of 1700 meters at a depth of 500 to 600 metres. At this time, geological reserves for the deposit were estimated to be 2.4 million tonnes at a grade of 5.0% U3O8 for a uranium content of 260 million pounds U308"

Jan 1, 2001

By Evangelos Petrakis, Kostas Komnitsas

This study investigates the evolution of dimensional properties of grinding products, namely, the mass, the surface area, the length, and the number of particle distributions with the energy input in a ball mill. The size analysis of the mill products enables the calculation of the mass distribution of each material at predetermined size classes and then the determination of the other dimensional properties by taking into consideration the geometry of the particles. Based on the distribution of dimensional properties, an effort was made to determine whether the grinding products are fractal in nature. The effect of material type and grinding conditions on the relationship between the dimensional properties and the specific energy input was also investigated. Special importance was assigned to the study of the specific surface area and the surface area production rate, both during the initial grinding stages and at higher energy levels. The determination of the surface area production rate allows the identification of the grinding limit and the maximum specific surface area which could theoretically be achieved. This approach has as ultimate objective the maximization of energy efficiency and subsequently the minimization of the high grinding cost.

By Evangelos Petrakis, Kostas Komnitsas

This study investigates the evolution of dimensional properties of grinding products, namely, the mass, the surface area, the length, and the number of particle distributions with the energy input in a ball mill. The size analysis of the mill products enables the calculation of the mass distribution of each material at predetermined size classes and then the determination of the other dimensional properties by taking into consideration the geometry of the particles. Based on the distribution of dimensional properties, an effort was made to determine whether the grinding products are fractal in nature. The effect of material type and grinding conditions on the relationship between the dimensional properties and the specific energy input was also investigated. Special importance was assigned to the study of the specific surface area and the surface area production rate, both during the initial grinding stages and at higher energy levels. The determination of the surface area production rate allows the identification of the grinding limit and the maximum specific surface area which could theoretically be achieved. This approach has as ultimate objective the maximization of energy efficiency and subsequently the minimization of the high grinding cost.

By I. C. L. Webster, G. E. Ray

"The magnetite-rich Heff Cu-Au skarn lies in the Quesnel Terrane of south-central British Columbia, approximately 26 km northeast of Kamloops. The skarn formed close to the northern margin of the Heffley Creek pluton, and is hosted by Carnian (Late Triassic) Nicola Group limestone. The Late Triassic pluton (208.1 ± 6.1 Ma, U-Pb zircon) is a composite body of alkaline affinity that includes dioritic, gabbroic, and magnetite-rich clinopyroxene ± olivine ultramafic phases.The skarn has been discontinuously traced along strike for more than 1 km, and individual skarn layers are up to 40 m thick. The most common non-opaque minerals are garnet, clinopyroxene, and carbonate, with lesser epidote, biotite, amphibole, and chlorite. Apatite locally forms more than 3 vol.% of the rock. Compositionally the garnet is a low Mn grandite averaging Pyr3-Grs41-Adr56 mol.%.Mineralization consists of lenses, up to 10 m thick, containing massive low Ti-V magnetite (avg. 0.03 wt.% TiO2 and 0.01 wt.% V2O3). Magnetite is associated with up to 20 vol.% pyrrhotite, lesser pyrite, and trace chalcopyrite and gold. There is a moderate enrichment in rare earth elements with assays up to 570 ppm La and 490 ppm Ce. The Heffley Creek pluton belongs to a suite of Late Triassic-Early Jurassic alkalic and Fe-rich intrusions that are widely developed throughout the Quesnel Terrane. Some host Cu-Au porphyry mineralization, but less commonly they are associated with magnetite-apatite veins such as at the Glen Iron mine and Magnet occurrence, or with magnetite-rich Cu-Au skarns such as the Heff occurrence.Although abundant low Ti magnetite is present in the Heff skarn, it does not appear to represent iron oxide copper- gold (IOCG) type mineralization. Microprobe analyses completed during this study show that low Ti magnetite is not a unique feature of IOCG deposits, but also characterizes some other types of hydrothermal mineralization. In British Columbia these include some alkalic porphyry-related magnetite-apatite veins in the Quesnel Terrane, as well as the well-known Wrangellia-hosted Fe skarn deposits. Thus, low Ti magnetite appears to be a common signature of many magmatic hydrothermal deposits in contrast to the high Ti primary magnetite found in most igneous rocks."

Jan 1, 2007

By Ron Frye, Carl Liibbe, Wayne Curtis, Julie Pecori, Dan Leach

Test work comparing the performance of a Low Density Porous Ammonium Nitrate Prill to regular Porous Ammonium Nitrate conducted in Pennsylvania and New York showed that less ammonium nitrate was required to perform the same work and that improved sensitization of an emulsion/ammonium nitrate blend reduced “orange fumes”. Fragmentation was similar in all tests with improved heave and throw experienced.

Jan 1, 1997

By V. C. Kelessidis

The interaction between rock and drill bit during drilling has been modeled for many years, but a complete understanding of the phenomena occurring has yet to materialize. Successful models will allow the prediction of rate of penetration in a given environment and optimal selection of drill bit and drilling parameters, thus minimizing exploration costs. In most rock-drilling models the value of the unconfined compressive strength of the rock (UCS) is used in the predictive equations, within the concept of specific energy, and the value of UCS is the percentage of the value of the stress applied on the drilling bit in order for the bit to advance. While the exact percentage depends on the model used and it is not known with certainty, good knowledge of UCS is nevertheless required before any decent prediction can be made on rate of penetration. Determination of UCS, normally done via destructive testing, requires not only the availability of sound rock core samples but also expensive testing and significant time for the test, which frequently are not available for routine drillability predictions. Hence, a multitude of methods and techniques has been proposed for estimating UCS from various indirect and/or non-destructive measurements, or combination of measurements with neural networks, such as point load index, block punch index, unit weight, and apparent porosity, water absorption by weight, sonic velocity, and Schmidt hardness. The many proposed approaches are critically reviewed and the results are compared, and what becomes apparent is that after many years, not only in mining but also in oil-well drilling, accurate indirect determination of UCS is still an elusive goal. An equation to predict UCS from sonic velocity data is suggested based on several data sets reported in the literature. Use of the specific energy equation with UCS or sonic data and utilization of drilling data allows an estimation of the efficiency of energy transfer from the bit to the rock and of the friction coefficient. Analysis of data reported in the literature, both from laboratory and field studies, has shown that this approach is sound and enables the determination of energy transfer efficiencies and friction coefficients, which for the cases studied range between 15 and 30% and 0.15 and 0.30 respectively. Thus, the suggested data analysis approach allows drillers to focus on inefficiencies and optimize drilling practices in future campaigns. Keywords Rock drillability, unconfined compressive strength, prediction.

Jan 1, 2011

By Fritz Grübl

Modern shield TBMs allow tunnel drives through almost any type of ground. Thanks to high elaborated technical measures, significant subsidence of the ground surface can be almost entirely avoided. The tunnel lining behind the TBM must be capable of withstanding all loads without deforming, especially during ring erection and advance. Single-shell tunnel linings behind the TBM, usually reinforced concrete segmental rings, can be designed to fulfill this demand. With many projects, however, damage occurs to the lining. Repair costs may be extremely high. Reasons for damages and possibilities to avoid them are shown and explained.

Jan 1, 2001

By C. Vipulanandan

It is critical to monitor the ground conditions during excavation and drilling of boreholes during construction to identify possible changes in the soil and rock formations. Drilled shafts are increasingly used as foundations to support structures, bridges and other facilities in geomaterials such as soft-rocks and hard clays. Locating the bottom of the borehole during construction with the required design strength is critical. Hence developing a simple device that could be easily adapted/used with the drilling tool was of interest in this study. Determining the shear strength of the geomaterial in the borehole and at various elevations including the bottom of the borehole can lead to better quality control of construction by identifying the various layers based on strength. In this study, a down-hole penetrometer (DHP-CIGMAT) was designed, built, calibrated and tested in the field to determine its effectiveness in measuring the strength of soil/soft rock in the boreholes. Based on limited field tests, linear correlations between geomaterial strengths and DHP-CIGMAT deflection have been developed. The DHP-CIGMAT can be used to identify soils and soft rocks.

By Marc Dondelinger

Interlocking H sections with deep webs and high section modulus are being used for cofferdams and shore enclosures where pressures are excessive. The H sections can be as much as a meter deep; they can be used as continuous interlocked wall. A steel saving alternate is spacing the H and driving deep for stability then filling between with shorter interlocking sheet piles. Templates provide for exact positioning.

Jan 1, 1985

The Century zinc-lead-silver deposit has a geological resource of 118 million tonnes averaging 10.2% zinc, 1.5% lead and 36 g/t silver. It lies approximately 250 krn NNW of Mt Isa in NW Queensland, Australia, and is hosted by middle Proterozoic age siltstones and shales of the Lawn Hill Formation. Within the orebody, most mineralisation occurs selectively within black shale units as fine grained sphalerite and galena lamellae with minor pyrite and siderite. The black shale units are separated by weakly mineralised sideritic siltstone horizons. The deposit is unmetamorphosed and only weakly deformed, displaying excellent lateral stratigraphic and grade continuity. The deposit is mostly overlain by younger Proterozoic sediments and later Cambrian age limestone cover and only a small proportion of the mineralisation crops out. Mineralisation has a subtle surface expression without a classic gossan profile, probably due to the low iron sulphide content of the ore. These factors contributed materially to the length of time between the first recognition of lead-zinc-silver mineralisation in the area by prospectors in the 1880s, to the discovery of the orebody by CRA Exploration Pty Ltd (CRAE) in April 1990.   Small scale prospecting and mining continued in the area from the date of the first mining lease in 1887. Post 1950, the deposit area was also included within nine separate regional exploration titles prior to CRAE's title acquisition in 1987. CRAE's original exploration strategy was partly pragmatically and partly conceptually inspired, but the eventual discovery only partly conformed to the original conceptual model. The deposit was found higher in the stratigraphy than the original target position, with unexpectedly low total sulphide content relative to other known deposits.   The discovery soil anomaly was located by the CRAE's first regional orientation traverse line in the area, but was not drill tested for three years. The discovery sequence at Century has strong elements of persistence, technical competence and some luck. It demonstrates that even in well explored terrains (by conventional standards) the exploration story can never be said to be over. The foreshadowed development of an economic resource at Century will hopefully inspire continued commitment to 'brownfields' exploration by mining companies, and demonstrate to external regulators the importance of genuine multiple land use strategies and the need for continued access to land for exploration and mining purposes.

Jan 1, 1995

By H. C. Liang

Reverse osmosis (RO) and nanofiltration (NF) are widely regarded as being best available technologies (BATs) for removing contaminants of concern from water. In recent years, NF or RO treatment has increasingly gained more acceptance in the mining industry for treating mine water to remove a wide assortment of contaminants, either for meeting discharge standards or for internal re-use in mining processes. Consequently, the number of NF or RO membrane mine water treatment facilities has steadily increased. Although NF or RO membrane filtration can be a powerful tool in mine water treatment, especially when multiple contaminant removal is required, it also has many potential disadvantages. Besides the generally higher capital and operational costs for the high pressure membrane processes, organic constituents in mine water may foul the membranes, while inorganic compounds such as gypsum, calcite, or silica are liable to scale the expensive membranes if proper pre-treatment processes are not implemented. Additionally, because these membrane treatment processes generate a substantial reject or brine waste stream in addition to the clean treated water or permeate stream, brine management also needs to be considered carefully when deciding upon the viability of an NF or RO mine water treatment process. Because of these issues, it is important to conduct detailed analyses of the trade-off between selecting NF or RO vs. using chemical treatment processes when designing a mine water treatment facility.

Jan 1, 2012

By K. P. Fournier

This report describes work on the problem of predicting oil recovery from a reservoir into which water is injected at a temperature higher than the reservoir temperature, taking into account effects of vis cosity-ratio reduction, heat loss and thermal expansion. It includes the derivation of the equations involved, the finite difference equations used to solve the partial differential equation which models the system, and the results obtained using the IBM 1620 and 7090-1401 computers. Figures and tables show present results of this study of recovery as a function of reservoir thickness and injection rate. For a possible reservoir hot water flood in which 1,000 BWPD at 250F are injected, an additional 5 per cent recovery of oil in place in a swept 1,000-ft-radius reservoir is predicted after injection of one pore volume of water. INTRODUCTION The problem of predicting oil recovery from the injection of hot water has been discussed by several researchers. l-6,19 In no case has the problem of predicting heat losses been rigorously incorporated into the recovery and displacement calculation problem. Willman et al. describe an approximate method of such treatment. 1 The calculation of heat losses in a reservoir and the corresponding temperature distribution while injecting a hot fluid has been attempted by several authors.7'8 In this report a method is presented to numerically predict the oil displacement by hot water in a radial system, taking into account the heat losses to adjacent strata, changes in viscosity ratio with temperature and the thermal-expansion effect for both oil and water. DERIVATION OF BASIC EQUATIONS We start with the familiar Buckley-Leverettg equation for a radial system:* This is sometimes referred to as the Lagrangian form of the displacement equation. If the injection water is at some temperature Ti which is above reservoir temperature TR, then lw, the flowing fraction which is water, is a function of both water saturation and fluid temperature at any given time and position in the reservoir. The temperature dependence of lw results from the temperature dependence of the viscosity ratio µo/µm of which lw is a function. Thus:

Jan 1, 1966

By Claude Bazin

"The On-Stream Analyzer has proven and is still proving to be an extremely valuable tool for the control of flotation circuits. This paper examines the possibility of going further in the utilization of the provided assays using a real-time material balance program to calculate the distribution of solids within the streams of a circuit. Mass balance results can be used for process control, process analysis and detection of sensors malfunction. Examples from 3 Canadian and one American concentrators are presented to illustrate the potential of the method.IntroductionThe On-Stream Analyzer (OSA) has gained, over the last two decades, the status of key instrument for the control of flotation plants. The OSA is currently used in almost every sulphide flotation plant and its application in oxide mineral flotation plants is increasing. On-Stream Analyzers provide X-rays pulse counts that are converted into assays using multilinear regression programs. The estimated assays are passed to the flotation operators, via an operator console, or to control loops of various degrees of complexity (McKee, 1991) implemented in a Distributed Control System (DCS). Operators and/or controllers take control actions based on these assays to ensure an adequate operation of the plant. Although this application pays off very rapidly for the purchase of the OSA, one should ask: Could we get more from the OSA?Some plants reported the use of OSA measurements to process optimization (McKee, 1991). The optimization strategy is based upon economic indices calculated from metal recovery using the 2 product formulae (Wills, 1992, page 124). The 2 product formulae is however sensitive to measurement errors in the assays and can lead to considerable scatter in the calculated indices (Hodouin et al., 1993). Least squares algorithms provide an interesting alternative to filter out measurement errors (Spring, 1992). This paper presents a recursive least squares algorithm that estimates in a real time fashion the mass flow rates in a flotation plant using OSA and mass flow measurements. The algorithm is robust and its recursive structure is not demanding in terms of computation time and memory. The method was tested with data from four concentrators. Results of the material balance algorithm prove to be useful to detect sensors malfunction and may potentially be used for the control and optimization of flotation plants.The paper is divided into two sections. The first section gives a description of the proposed method. The mathematics of the method are kept to a minimum, since the detail is presented elsewhere (Bazin and Franklin, 1994). The second section shows the application of the method to different flotation plants."

Jan 1, 1995