Search Documents

By Wenbing Xie

At Renlou Coal Mine, Huaibei Mine Area, the track entry deformed significantly after longwall mining in an overlying multiple seams. The supporting characteristics of primary roof bolts and shotcrete with wire mesh are closely related to the movement of the mine?s surrounding strata. A case study of a track entry deformation was monitored during the longwall mining of a selected overlying panel. The measured data showed the unique entry deformation pattern during the longwall mining in the overlying seam. Underground extensometer measurement showed that entry stability was mainly affected by the periodic roof weighting of longwall mining in the overlying seam. The displacement of the deeper strata occurred a head of the immediate vicinity of the entry. Thereafter, deformation of the roof and floor strata was in the form of shearing of the shallower strata. Due to the use of heavy-duty roof bolting with wire-mesh, the roof-tofloor and rib-to-rib convergences were small, but the floor heave was large, greater than 80% of the roof-to-floor convergence. The measured displacement from extensometers varied with the position of the monitored cross-sections and depth into the roof. There were several deformation patterns, such as shearing movement, compression, and expansion, and the variations between compression and expansion. Strata compression at the entry surface was always accompanied with shearing movement at the deeper strata. During the longwall mining, the whole surrounding strata of the entry moved toward the opening. Underground practical experience indicated that prior to mining, the entry was supported very well in excellent conditions. After mining, however, it deformed greatly. The current entry support technology was not effectively control the severe deformation incurred in entries driven in soft strata due to the following reasons: (1) little is known about the entry deformation behavior of the strata surrounding the opening and (2) the degree of interactions between entry deformation and roof bolting with wire mesh is not well understood. Consequently, effective supporting systems cannot be properly selected to control its deformation and maintain a stable supported surrounding structure.

Jan 1, 2012

By S. E. Phillipson, P. L. Tyrna

Lineament analysis, a remote sensing application for geological structures, has been criticized for reliance on subjective interpretations. The Mine Safety & Health Administration’s Roof Control Division performs lineament analyses with a technique that removes much subjectivity. Study areas are viewed on satellite images with software that allows examination under artificial sun azimuths and elevations. Extraneous lineaments are removed through successive steps of superposition, resulting in selection of the most robust linear features. Field investigations revealed a strong coincidence of joint and fault zones that were parallel with projected lineaments. The Roof Control Division’s successful identification of lineaments associated with roof falls and highwall failures has prompted some mine managers to incorporate lineament analysis as a mine-planning tool. The identification of potentially hazardous ground conditions will allow mine operators to obviate safety concerns that might otherwise adversely affect miner health and safety.

Jan 1, 2002

Quantitative seismology is an important tool for investigating mineinduced seismicity and the quantification of the seismic rock mass response. The spatio-temporal interpretation of seismic data within an ever-changing three-dimensional mining environment provides some challenges to the interpretation of the rock mass response. A grid-based approach for the interpretation of spatial variation of the rock mass response provides some benefits compared with approaches based on spatial filters. This paper discusses a grid-based interpretation of seismic data. The basic methods employed in the evaluation of the parameter values through space are discussed and examples of applications to different mine sites given.

Jan 1, 2014

By R. Q. Shotts, H. J. Hager, A. C. Richardson, G. D. Coe

"INTRODUCTION In the State of Alabama few mines produce coal clean enough to be marketed directly without being washed. This is particularly true where the coal is to be used for the production of metallurgical coke. In washing plants where single-compartment jigs alone are used to treat a large range of sizes, it has been found that the washed coal finer than 1/4-inch contains a large proportion of free impurities and is much higher in ash content than are the coarser sizes. To reduce the ash content of this fine material with jigs usually entails a greet reduction in capacity and a loss of coarse coal in the refuse. This investigation, conducted by the Southern Experiment Station of the United States Bureau of Mines in cooperation with the University of Alabama and the Alabama By-Products Corporation, was undertaken to determine whether the fine washed coal from jigs could be economically re-treated on coal washing tables.COALS TESTEDThrough,the cooperation of the Alabama By-Products Corporation, samples of fine-sized washed coal were obtained from their washeries at Bradford and Gamma.The Bradford mine, on the Black Creek bed, yields a low-ash, medium-volatile coal with fairly good coking properties. This coal is blended with coal from the Mary Lee bed for coking purposes and compensates for the high ash content of the latter. The Black Creek bed is about 30 inches thick and seam analyses show an ash content of from 2.0 to 4.0 per cent. In the Bradford mine the undercut is about 6 inches high, so that a large proportion of fines is produced."

Apr 1, 1932

The past decade has seen revolutionary advances in communications and information-handling techniques which have been stimulated by "cold war" military requirements and by current programmes for probing into outer space. The tools used in exploration for petroleum and minerals have been improved significantly as a result of this new space age technology and even greater improvements are on the way.Two areas of technical activity have been particularly fruitful in enhancing the effectiveness of exploration methods. These are1. the development of new approaches, based on information theory,for extracting signal from noise more efficiently than before, and2. the use of high-speed digital computers for storing and processing all kinds of exploration information, not only geophysical but geological as well.In seismic prospecting, use of information theory has led to new techniques such as time-domain filtering, wave-number filtering and correlation methods which have made it possible to obtain usable reflection data from areas which were previously considered non reflective. Complex playback and other data processing facilities have been developed to apply these approaches.Digitization of geophysical data for handling by high-speed electronic computers facilitates many of these techniques for signal-to-noise improvement. Direct digital recording of seismic data in the field is now being d'one on an experimental basis in the United States, and this should become a standard procedure, at least for problem areas.The increased dynamic range, flexibility of filtering and other data processing, and convenience of information storage and retrieval make digital recording attractive in spite of its high cost compared to conventional analogue methods. Digital computers are being programmed to carry out many operations in data reduction and interpretation with substantial savings in time and cost over conventional procedures.INTROPUCTIONIn the years that have passed since the end of the Second World War, the western world has witnessed a technological revolution which may be as far reaching in its ultimate impqct as the Industrial Revolution of the last century.

Jan 1, 1963

By Joshua Micah Hoffman, Jhon Silva-Castro, Kylie Larson-Robl

A coal mine impoundment failure has the potential to be environmentally devastating and life-threatening. It is well documented that after seismic events slope failures in impoundments can occur. It has been concluded that often the main driven factor of the failure is the increase in excess pore pressure due to ground vibration. A small amount of research has been done regarding the stability of coal mine impoundments under natural seismic events; however no research has been done considering vibrations from mine blasts. If it is taken into account that current environmental restrictions oblige to increase the capacity of coal mine impoundments, thus increasing the hazard of such structures, it is necessary to evaluate the effects of near-by mine blasting on the stability of the coal mine impoundments in order to mitigate and control the potential of slope failures. To study the behavior of excess pore pressure under blasting conditions, scaled simulations of production blasting events were set up inside of a controlled sand tank. The research was divided in two stages. The first one was done, using dry conditions, while in the second part, the same set of tests were performed under saturated conditions. This document shows the partial results for stage one (dry conditions). For the tests, explosive charges were set off within the sand tank at various distances to simulate different blasting distances. Information was collected from geophones, accelerometers, microphones and high speed video camera for dry and saturated scenarios and additionally from piezometers under saturated conditions to assess the behavior of the material under blasting conditions.

Jan 1, 2015

By Tristan H. Jones

Beginning in 1987, miniature dataloggers approved by the Mine Safety and Health Administration (MSHA) were publicly available for sale. The principal among these was the model CR21XQM, manufactured by Campbell Scientific, Inc. These dataloggers had been tested and were deemed permissible by MSHA and thus could be installed in the return air of an underground coal mine. In 1996, production of all permissible Campbell Scientific dataloggers ceased due to lack of sales. Data collection with these dataloggers has been a staple of ground control research in the United States for decades, and, without them, or a replacement, the capability to monitor ground behavior is severely impacted. Since that time, any party requiring a permissible datalogger has needed to borrow one that was purchased during the production years. In order to fill this technology gap and ensure its own data-gathering capabilities, the National Institute for Occupational Safety and Health (NIOSH) has developed and refined its own miniature data acquisition system (MIDAS). On February 16, 2010, MSHA deemed the MIDAS to be permissible and approved it for use in the return air of an underground coal mine. The MIDAS is an intrinsically safe, 16- or 24-bit datalogger, compatible with a wide range of resistive, single-ended, and differential-type instrumentation. It contains enough data storage memory to operate for over a year with typical data rates and is efficient enough to do this on a single C-sized alkaline battery for that entire period. It is menu-driven and requires no programming knowledge to operate. It supports wireless or hardwired communication for datalogger setup and data download. This paper describes the design, field and laboratory testing, and capabilities of the MIDAS datalogger. While not as fully -functioned as the CR21XQM, it is the only new permissible datalogger available, and there is intent to make it available to the mining industry for purchase.

Jan 1, 2012

By R. G. Gillies

The pipeline transport of paste, backfill or thickened tailings slurries is an important component of the tailings disposal process in many mines around the world. These mixtures contain significant fractions of fine (clay) and coarse (sand) particles, causing them to exhibit non-Newtonian flow behaviour and high frictional pressure gradients. There is often economic incentive to operate these pipelines in the laminar flow regime. Irrefutable evidence has shown that coarse particle settling can occur during the laminar flow of these slurries even when static settling tests show no indication of such behaviour. Previously, a ?rule-of-thumb? minimum frictional pressure gradient of ~1.5 to 2 kPa/m was suggested to ensure effective sand transport, based on the results of tests conducted using viscous Newtonian oils. In this paper, we examine the results of laminar flow tests of non-Newtonian, coarse-particle laden slurries conducted with pipeline loops of 50, 100, 150 and 250 mm in diameter. The results indicate that the ratio of the mean wall shear stress to the mean surficial particle stress is a better indicator of laminar flow settling tendency than frictional pressure gradient.

Jan 1, 2007

By K. Lundholm, M. Andersson, L. Nevatalo, Å. Holmström, L. Hedström

"Several copper deposits have the arsenic bearing minerals enargite (Cu3AsS4) and tennantite (Cu12As4S12). Since this mineral contain both arsenic and copper, it is not possible to remove the arsenic by selective flotation. Partial roasting is a method to clean the concentrate from arsenic and thereby produce a suitable raw material for the copper smelter. Also mercury is commonly found in copper bearing minerals. In the partial roasting process both arsenic and mercury are volatilized, while part of the sulphur is used as energy during the roasting. This gives a calcine suitable as feed to a smelter, much like an ordinary copper concentrate. A typical analysis of calcine would be: S content 18–22%, As content below 0.3%, Cu content – not affected, grain size – not affected. However, if the concentrate contains mercury, the mercury will be volatilized during the roasting process. This will lead to very high mercury contents in the subsequent process of sulphuric acid, unless the SO2-rich process gas is pre-treated by the Boliden/Norzink process that recovers mercury as calomel, Hg2Cl2. The volatilized arsenic in the gas phase can be recovered either by dry or wet methods. However, one problem is that arsenic also contaminates the fine grained calcine dust that is captured downstream in the gas cleaning system. The calcine dust contains valuable metals such as copper, gold and silver that needs to be separated from the arsenic. The ultimate aim is to stabilize the recovered arsenic as a compound with minimum impact on the environment and recover the valuable metals. By using wet recovery methods it is possible to selectively precipitate copper, gold and silver as sulphides while arsenic is kept dissolved in the liquid. The precipitated metal sulphides can be mixed with the calcine and sent to the copper smelter. The dissolved arsenic is sent to effluent treatment and is further treated in Outotec ferric arsenate precipitation process, where arsenic is precipitated as the stable compound basic ferric arsenate, formula FeAsO4·xFe(OH)3. All concentrates containing arsenic are unique and the process design of a roaster plant must be based on relevant process data. The process data is collected during tests in lab scale and pilot scale, where the influence of critical process parameters on the quality of calcine is studied. The ability to run tests both in lab scale and pilot scale is crucial to the development of the correct roasting process. Outotec is well equipped for this."

Jan 1, 2014

By Tapio Leskinen

"In the 1960’s, when large flotation machines appeared on the market, this was a part of a world-wide trend towards the use of ever larger machine units.One factor that has played a decisive part in this development is the increased of the amounts of ore that have to be handled as the exploitation of successively poorer ores becomes necessary. The advancing application of instrumentation and automation has worked in the same direction.In 1970, a working group was set up within Outokumpu Oy, for the purpose of flotation machine development. The principal task of this group was to be the design and development of- a new type of rotor of increased efficiency, especially for the dispersion of large amounts of air- a mechanical-pneumatic flotation machine of substantially larger size that existing plant.This development project required an extensive program of theoretical investigation and experimental studies at several concentration plants of the company.The commonest flotation machine presently used in the concentration plants of Outokumpu Oy is the VK-3. It is of the mechanical-pneumatic type, and the volume of its cell tanks is 2.5 m3 per shaft. This machine was developed within the company, and its first development phase i s represented by the OKKO 3, built for the Kotalahti concentrator in 1959. It was, in its time, comparable in volume to the largest machines that were then in use anywhere in the world."

Jan 1, 1976

Individual specimens of sphalerite from the Broken Hill lode vary considerably in manganese and iron contents, even within the same orebody, so that study of the overall variation of manganese and iron content of the sphalerite calls for the analysis of a large number of specimens. This difficulty has been overcome by analysing a series of recleaned zinc concentrate products, prepared from stope samples and their equivalents, from most of the developed sections of the lode. The analyses reveal that during the formation of the sphalerite the concentrations of iron, manganese and zinc in the mineralizing solutions varied independently of one another from place to place in the forming orebodies, and also in time.The overall pattern of variation of the iron and manganese contents of the sphalerite in the several orebodies of the lode bears a general resemblance to the overall pattern of distribution shown by several other elements, notably, cadmium, lead, bismuth and arsenic. The iron content of the sphalerite indicates that it was formed at a temperature of 6000 C. or higher, but the variation in its iron and manganese contents demonstrates that Kullerud's method for determining the temperature of formation of sphalerite from its iron content must be used with caution if only single specimens of sphalerite are available.INTRODUCTIONThe four chemical analyses available of specimens of practically pure sphalerite from the Broken Hill lode (Table 1) reveal that the manganese content of the sphalerite varies considerably, and that there is a significant variation in its iron content. The variations revealed between individual specimens within the same orebody in the same mine suggest that specimen material is unsatisfactory as a basis for studying the overall manganese and iron contents of Broken Hill sphalerite, unless a great number of specimensis analysed.

Jan 1, 1956

By S. C. Brown

A number of studies have suggested that microscale asperities enhance bubble-particle attachment efficiency; however, in practice the roughening of particulate surfaces can also lead to a decrease in flotation. In the present investigation, it is proposed that nanoscale asperities may be partially responsible for this phenomenon. It is suggested that as inter-asperity separation distances are reduced capillary effects are enhanced leading to the formation of stable liquid domains, which adversely impact bubble-particle adhesion. In addition, obstruction of surfactant self-assembly may occur, further limiting flotation.

Jan 1, 2003

By O. Rondon

Localized uniform conditioning is a technique developed to spatially locate selective mining unit grades that have been derived using uniform conditioning for the assessment of recoverable resources. The technique has the advantage of producing selective mining unit estimates conforming to the uniform conditioning panel-specific grade-tonnage curve while introducing spatial information at the scale of the selective mining units. This paper describes an alternative technique to localized uniform conditioning which does not explicitly require the uniform conditioning panel-specific grade-tonnage curve to localize the selective mining unit estimates. The technique can therefore be implemented in mining software where uniform conditioning is not available.

Jan 1, 2014

By D. J. Duck

INTRODUCTION Construction of the 3,600,000 kilowatt Third Powerplant at Grand Coulee Dam started in late summer 1967 approximately one year after authorization by Congress. The project was made possible by a treaty with Canada providing for cooperative development of the Columbia River which was signed in 1961 and ratified in 1964. Description of the Work The existing Grand Coulee power complex consisted of a dam and two powerplants with a switchyard serving each plant, one on each bank of the river. See Fig. 1. The switching facilities were connected to transformers at the powerplants by overhead 230-kilovolt and 115-kilovolt tie circuit conductors. [ ]

Jan 1, 1997

By O. Celep, T. Uslu, Savas

This study investigates the enrichment of a low-grade colemanite concentrate (-3 mm) using a Knelson centrifugal gravity concentrator. Due to its low boron content, the concentrate is unsaleable and has to be stored under appropriate conditions to avoid potential environmental problems. The low-grade colemanite concentrate was comminuted to size fractions of-1 mm, -0.5 mm, and -0.15 mm before treatment in the Knelson Concentrator. The effects of particle size, fluidizing water velocity, and bowl speed on the enrichment process were examined. The B2O3content of the concentrate was increased from 33.96% to a maximum of 45.52%. B2O3recovery increased with increasing bowl speed and particle size, and decreased with increasing fluidizing water velocity. The enrichment process also rejected arsenic and iron to some extent, with a maximum reduction of arsenic from 1360 g/t to 765 g/t and iron from 0.88% to0.33%.

Jan 1, 2015

The Mineralogy and Reactivity of Pyrrhotite from Selected Nickel Ore Deposits and its Effect on Flotation Performance

Sep 13, 2010

Following a short review of selected literature, a back analysis of stress measurements of stress regeneration in a closed mini-longwall is shown. The agreement is good, lending confidence to the parameters used in the proposed numerical model. Foundation yielding was modelled in the absence of total stope closure. A ?Prandtl? wedge was formed, coinciding with the yield point of the pillar/foundation system. Some theoretical work is used as a starting point for the formulation of a new design methodology for strike or dip stabilizing pillar/foundation systems in deep level goldmines. The existing guideline for the stability of foundations (APS< 2.5UCS) is critically examined. Finally, the advantages of the new approach, and the work required to substantiate the proposed new design methodology, are outlined.

Jan 1, 1998

By George Anagnostou

Time-dependent ground behavior may have important implications for the construction process or the life of a tunnel. The paper gives a concise overview of the influence of time on the deformations and the stability of underground openings, including topics such as face stability in soft ground or the time-development of pressure or deformations in squeezing or swelling rock. While keeping in mind practical questions of tunnel engineering, emphasis is placed on understanding the observed time-dependency, on the underlying mechanisms (such as pore water pressure dissipation or chemical processes) as well as on the respective inherent prediction-uncertainties and design-uncertainties.

Jan 1, 2007

By Joe Pease

"The demand for minerals and metals is increasing. Head grades of ore bodies are dropping. Remaining ores are becoming finer grained, more complex, and more logistically challenging. Mineral processing – in particular comminution – already consumes a huge amount of energy. But in 20 years’ time, it will require about six times as much energy as today to meet the world’s mineral demand.Unless we do something different.As minerals professionals, it is our job to find that “something different”. The world is relying on us. Of course, we must look for new breakthrough technologies and techniques. We must find them, and we will find them – most likely in surprising areas.But what if we also already know how to make 30-50% improvements to efficiency? Just by using existing technologies, by applying modern analytical techniques, by custom designing our plants, by applying manufacturing principles, by breaking down our management silos between disciplines.The thing is, industry professionals already know this. Yet – in spite of a lot of intelligent people trying very hard – we just can’t seem to make it happen.This discussion considers why, despite our best efforts, we don’t get the best out of what we already have. Why we are wasting energy and money. Once we understand why, we can set about unlocking that value and improving industry productivity and energy efficiency. We will discuss the role that professionals and volunteer professional organisations like CMP and CEEC can play in catalysing the changes."

Jan 1, 2015

By J. M. Tannenbaum

A depth-sensing micro-indentation technique is developed for evaluating mechanical properties of materials at elevated temperatures (to 1200°C). System description and design considerations of the test apparatus are described. Based on Hertzian spherical indentation approach, the micro-indentation test apparatus is capable of determining Young?s modulus and creep strength of test materials with flat, tubular, or curved architectures from room to 1200°C under either air or controlled gaseous environments. Calibration tests were conducted on a H13 Tool Steel coupon from 22°C to 500°C and single crystal Haynes 230 alloy at 1000°C with excellent agreement to the literature values. Indentation creep tests of Haynes 230 alloy were carried out at 1200°C with preliminary results showing good correlation to creep exponents. Further system refinements will be investigated, and additional testing will be conducted.

Jan 1, 2010