Search Documents

A fundamental component of grade control at Tarmoola Mine has been the monitoring of assaying through quality assurance programs. The programs have concentrated on issues related to accuracy and precision of leachwell and fire assay techniques, sample preparation and grade variability within a sample. An outcome of monitoring has been identification of shortcomings in the application of assaying techniques to Tarmoola ore types that contain coarse particulate gold. Leachwell has shown satisfactory precision since introduction as the primary assay technique in October 1998 but leachwell accuracy and recovery through comparison with fire assay techniques has identified bias. A bias toward higher fire assays in grades above 2 g/t invoked an investigation into the cause of the discrepancy between leachwell and fire assay. Testwork evaluated Leachwell assay recovery by varying leach time duration, which showed that by increasing the leach time improved recovery significantly. Monitoring of leachwell against fire assay had shown that a leachwell (200 g) with a one hour leach has under-called grade when compared with fire assay by up to 18 per cent, on average, for Tarmoola ore types. Alternatively, optimisation of the leachwell assaying technique using a 200 g pulp and a two hour leach has returned, on average, higher assays than fire assay by up to eight per cent. Testwork on screen fire assays, duplicate assays and fire assay to extinction has demonstrated assay variability associated with coarse, particulate gold. The variability and distribution of gold in Tarmoola ore types has emphasised the importance of high quality sample preparation for leachwell assaying to ensure liberation of gold to leaching solutions. Assay quality assurance protocols are vital to assay data integrity and enable confidence in delineation of ore-waste boundaries and provide early recognition of problematic assaying periods and isolation of grade control practices, which depart from performance standards critical to the operation.

Jan 1, 2000

By Scott A. Stebbins

Cost evaluation models constructed specifically to evaluate the economic potential of an individually motorized railcar system of ore and waste transport demonstrate that the approach may be considerably more cost effective than traditional rubber-tired haulage methods. The system design places a motorized drive unit on each railcar, as opposed to the more common configuration in which a series of un-motorized cars trail behind a single locomotive. These motorized railcars are directed to various load and dump points by a computerized dispatch system, and as such have the advantage of operating unmanned. In addition, the tractive effort of the rail-type drive system is noticeably more efficient than that of the rubber-tired mode of transport. The savings are realized primarily through comparative reductions in the requirements for labor and, to a lesser degree, energy.

Nov 1, 2011

By W Farnworth

The Huntly West Mine has undergone significant changes in the last two years, which will affect the remainder of the mine's life. The paper describes the evolvement of plans and an overview of the technical considerations made in planning for and implementing the first New Zealand longwall operation. The technical investigations involve the longwall equipment, exploration, ventilation and strata control. The focus on these areas was to ensure that unacceptable project risks were addressed. Implementation of longwall mining at West Mine is planned in three phases, Development, Panel One extraction trial, and Full Longwall operation.   At present the development phase is complete, longwall installation is in progress and production start-up is planned for the end of August, 1991.

Jan 1, 1991

By P. T. O'Kane

"INTRODUCTION Wright Engineers Limited is active and has extensive experience in the design of pressure oxidation plants for the treatment of refractory gold ore and concentrate. In addition to the Mercur oxidation facility, similar projects undertaken during the last few years include the 3000 ton per day acid oxidation plant for the Getchell Mine, Nevada, a concentrate treatment autoclave for Asamera in 1984 and a feasibility study of a 50-tons per day autoclave plant for Consolidated Professor's Duport property in Ontario. The Equity Silver antimony and arsenic precipitation autoclaves, and the low pressure autoclaves at Key Lake Uranium in Northern Saskatchewan were also engineered by Wright in recent years.In August 1986, Wright was retained by Barrick Resources (U.S.A.) Inc. to add a 750 tpd pressure oxidation circuit to the existing mill at their Mercur Gold Mine, Utah. This paper describes this facility and outlines the start up in the spring of 1988 and subsequent successful operation. MERCUR OPERATION The Barrick Mercur Gold Mine is located at the south end of the Oquirrh Mountains in Tooele County, Utah. The carbon-in-leach (CIL) process plant camnenced operation in 1983 with a design throughput of 3000 tpd and has since been expanded to handle rrore than 5000 tpd. 'IWo ore types are mined, an oxide ore and a refractory ore, which is by Barrick's definition ""an ore from which less than 60% gold extraction is achieved by a standard CIL amenability test."" Typical of many sulphidic/carbonaceous ores, the refractory gold does not respond well to the cyanidation process. As a result, refractory ore has been stockpiled since the start of mining. As of June 1987, Mercur had about 570,000 tons of refractory ore stockpiled and 5.7 million tons of proven and probable reserves, grading 0.06 oz/t including approximately 3.5 million tons of tailings from the previous operation grading 0.55 oz/t. In 1986, Barrick decided to build a 750 ton per day pressure oxidation plant to process these ores. The process, for which a patent was granted, comprises pressure oxidation of the sulphides in an alkaline environment. It was developed in 1981 but was set aside in preference of a CIL plant treating only oxide ores by the previous owner of the property, Getty Oil. This process is capable of increasing gold recovery from the refractory ore from as low as 35% by conventional CIL processing to more than 85%. In 1986 Wright Engineers was engaged to undertake a feasibility study based on batch testing. This lead to a decision by Barrick Mercur later that year to build the commercial pressure oxidation plant. Wright was awarded the contract for engineering, procurement, construction managernent and commissioning in March 1987. The plant was mechanically complete in January 28, 1988, and was in operation by February 1988."

Jan 1, 1989

To the members of The South African Institute of Mining and Metallurgy We have audited the annual financial statements of The South African Institute of Mining and Metallurgy set out on pages 451 to 460 for the year ended 30 June 2002. These financial statements are the responsibility of the Institute?s Council. Our responsibility is to express an opinion on these financial statements based on our audit. Scope We have conducted our audit in accordance with statements of South African Auditing Standards. Those standards require that we plan and perform the audit to obtain reasonable assurance that the financial statements are free of material misstatement. An audit includes: ?examining, on a test basis, evidence supporting the amounts and disclosures in the financial statements, ?assessing the accounting principles used and significant estimates made by management, and ?evaluating the overall financial statement presentation. We believe that our audit provides a reasonable basis for our opinion. Audit opinion In our opinion, the financial statements fairly present, in all material respects, the financial position of the Institute at 30 June 2003 and the results of its operations and cash flows for the year then ended in accordance with South African Statements of Generally Accepted Accounting Practice. Auditors 29 July 2003 Council?s approval of the annual financial statements The annual financial statements for the year ended 30 June 2003 set out on page 451 to 460 were approved by the Council on 26 July 2002 and are signed on its behalf by:

Jan 1, 2003

The principle activities of the Explosives Research Laboratory from July 1, 1961 to June 30, 1962, are described briefly in part 1. Part 2 gives short abstracts of publications that appeared during fiscal year 1962; in general, the research reported in these publications antedates the report period. Part 3 gives the results of an investigation which, although too limited to warrant separate publication, merits presentation in some detail because of current interest in ammonium nitrate-fuel oil compositions.

Jan 1, 1964

By Julie Shang, Tim Evans, Michael McDonald, Yu Guo, Bingfeng Xue

Effective chemical grouting represents a technical and economic solution to many challenges related to soil stabilization and blocking the flow of water. Chemical grouts are facing increasing demands in durability, environmental impact and value. To better meet these challenges, a novel and cost effective process was developed to produce a sodium silicate that increases the ratio (i.e. silica to alkali) beyond what has been used in traditional silicate-based grouts. The move to a lower sodium form of silicate was anticipated to have two desirable performance enhancements; a reduction in leachable sodium and improvement in the durability of the silicate grout. An in-depth study was performed at the University of Western Ontario Geotechnical Research Centre to quantify improvement in durability as well as other performance properties such as compressive strength. The study began by first modelling the gelation time and reaction kinetics of the high ratio sodium silicate over a range of silicate concentrations using two different setting agents as well as with/without a hardener. As expected, reducing the level of sodium produced a much more water resistant grout. These same formulations also showed a four order magnitude reduction in permeability. Somewhat surprising, test results showed the higher ratio silicate having much higher compressive strength. At the time of this abstract, the high ratio silicate was moving to the trial stage for geotechnical applications while the petroleum industry was further along with several successful field trials for water blocking as well as cement remediation. This paper will review the chemistry, testing and features of this next generation form of sodium silicate. Introduction Sodium silicate based grouts have been used for decades for soil stabilization and water control. Over the years, several silicate-based systems have been tailored for specific application conditions to maximize performance and reduce cost. Past research has also focused on the selection of setting agents and hardeners for silicate grouts. A constant in the development effort has been the grade of sodium silicate. The vast majority of chemical grouts have been formulated using a ~3.2 ratio sodium silicate. As a very brief overview on the meaning of “ratio” and why it is so important to performance properties. The ratio describes the proportion of sand to alkali or SiO2:Na2O used to make different grades of sodium silicate. Comparing a 2.2 ratio to a 3.2 ratio, it is easier to polymerize and set the 3.2 ratio. Upon setting and forming a silica gel, the system has higher compressive strength values and improved durability with a reduced level of syneresis (i.e. shrinkage). This leads to the question if 3.2 is better than 2.2 why not go to 4.2 or higher?

Jan 1, 2018

By A. Habibi

A study has been undertaken on two 1.12 m diameter industrial booster fans operating under different blade settings powered by a 1200 rpm motor at the Missouri University of Science and Technology. The fans total pressure varies up to 1kPa forcingup to 25 m3/s through the workings. A pressure-quantity survey has been conducted inby and outby the booster fans with different blade settings. The study uses a variable speed drive (VFD) to determine the effect of rotational frequency on the system. The pressure drop across the bulkheads has been monitored during the experiments. The fans were operated with various blade settings to determine the optimal scenario that maintains the maximum airflow quantity and the lowest power demand at a particular ventilation station. Five scenarios were conducted with different blade setting and mostly with two different speeds. The experimental results show that alteration of fans? speeds by use of a VFD unit can reduce power consumption while maintaining airflow requirements. With the flow rate forced through the mine by the surface fan the blade settings 4 and 5 were determined as possible alternative for the mine ventilation system. In scenario 4, the airflow at the particular ventilation station for a number of speeds is over 20m3/s. The power consumption at 1080 rpm was measured to be 20.1 kW compared to 25.5 kW at 1200 rpm. The operating cost would be significantly less at lower speeds. Scenario 5 is the alternative making use of both booster fans and the main fan in series that meets the minimum airflow requirement at the particular ventilation station along with minimum power consumption. Reducing both booster fans speeds to 1054 rpm results in power consumption of both together dropping to 11.8 kW. Therefore blade setting 5 using two booster fans was determined to be the optimal setting. Separately it was determined that the combination with use of only one booster fan, the West booster fan, running in series with the main fan is the overall optimal scenario. The power consumption of the West booster fan was calculated to be 8.8 kW at 860 rpm with the minimum airflow requirement being met. Computational fluid dynamics is used for analyzing three dimensional flow structures in time domain and calculating the corresponding unsteady pressure fluctuations. The sliding and dynamic mesh techniques were used to study the unsteady flow interaction arising due to the rotation of the fan blades. The numerical predictions of the variables in the form of velocity vectors and contour plots detailing the flow characteristics are then analyzed according to the known physical situation and existing experimental data.

Feb 27, 2013

By Frédéric Flament, Luc Lachance

"The important task of metallurgical accounting that used to be done manually is being more and more automated. Currently available solutions can generate accounting reports without human intervention or almost. However, the practical conditions for fully delivering the promised benefits of those solutions are sometimes overlooked either by end-users or by integrators. The mere fact of filling reports with values satisfying several constraints such as mass conservation constraints does not, by itself, ensure a high quality metallurgical balance. Since managers make decisions based on these reports, it is logical that the metallurgical balance performance be monitored and retrofits be made if necessary. Such retrofits may involve modifications to the measurement strategy or the reduction of the spatial resolution of the material balance model. This requires an estimability and redundancy analysis (ERA) tool to assess the feasibility of the modified model. Since determining by hand the estimability and redundancy of a set of non measured and measured variables is not trivial, even for a medium-sized mineral processing plant, a dedicated ERA tool brings valuable assistance to the metallurgist in charge. The present paper aims first at explaining how a state of the art metallurgical balance is a key enabler for the adoption of a smart process plants paradigm (SPPP) in mineral processing. Then, the fundamentals behind the building of an ERA algorithm are introduced and illustrated by two examples. Finally, the role of an ERA tool in achieving state of the art metallurgical accounting and how it contributes to delivering additional value are discussed.INTRODUCTIONThe Smart Process Plants Paradigm (SPPP)Mineral processors have seen an increase lately in external pressures toward operating performance improvements. Indeed, the globalization of the mining business is a key driver to becoming more productive, more responsive to market changes, to improving corporate governance and reporting standards. Furthermore, mineral processors are also expected by their neighbouring communities to continuously improve their sustainability score. These current pressures differ somewhat from the past ones in leading to a larger than ever number of conflicting constraints that plant managers must concurrently satisfy while maximizing plant profitability. It is in turn not surprising that this context requires actions involving more real-time collaborative actions between more people in more places than ever before."

Jan 1, 2011

By L. J. E. Hofer, J. L. Snyder, J. N. Barn, J. E. Chilton, W. E. Thomas

Various silicone materials have been proposed for use in mining environments. The catalytic methane sensors now employed are poisoned by silicone vapors. Activated charcoal and carbon cloth adsorbents will increase the sensor lifetimes in an environment containing significant silicone vapor concentrations. The results of a study of catalytic methane sensor operation with adsorbent materials in hexamethyldisiloxane-air mixtures are reported. Sampling techniques developed for measuring silicone vapor content of mine atmospheres are described.

By Walter D. Holland

This is one of a series of instruction guides developed to help instructors present health and safety training courses to workers in the metal and nonmetal mining industry. This course is intended for training those, usually the safety officers, who perform surveys for inhalation contaminants in above ground work areas. The handbook entitled ?Handbook for Surveys of Inhalation Contaminants in Above Ground Metal and Nonmetal Mining and Processing Work Areas? is used as a manual for the course and as a prime reference when performing the actual surveys or interpreting the sampling results. There are six experiments for the students to perform during the course to familiarize them with the sampling devices routinely used during the surveys.

Jan 1, 2011

By Robert S. Dewey

AS a result of drilling operations during 1943, West Texas again added sufficient new oil reserves to replace the oil produced during the year, but failed to maintain its position in currently available reserves because the deeper discoveries will require years for development. Drilling failed to provide the additional oil necessary to meet the increase in current and anticipated market demand. Although 13.3 per cent of the total footage drilled was in wildcat exploration, the ratio of oil discoveries to total wildcats was less in 1943 than in 1942, but comparable to that in 1941. Of the 732 field wells completed, 270 were at Slaughter, 55 at Wasson, 45 at Mascho and 31 at North Cowden. As of Dec. 31, 1943, there were 361 drilling wells including 71 wildcat and 290 field wells; 19.7 per cent were wildcats. It is anticipated that the percentage of wildcats of the total wells will be higher during 1944 than in either 1942 or 1943. Tables 3 and 4 present a three-year comparison of drilling activity and illustrate the downward trend of development that has been in effect during that time. Because of development lag in the deeper Ordovician fields, several years elapse before 2 sufficient number of wells is completed to give a substantial producing rate. As these new oil reserves cost more to find, and will cost more to produce on a barrel basis than the oil marketed during the year, their reserve replacement value to the industry is less in money. Costs While complete costs for deeper drilling are not yet available for analysis, it is evi- dent from the data on drilling rates to comparable depths, contract prices, and general increases in costs, that the cost of drilling has risen approximately 20 per cent during the year. One representative drilling contractor estimates that the average drilling time on a 5000-ft. field well has increased nearly one third and that out-of-pocket costs have increased a dollar per foot. Three major factors contribute to this increased cost: (I) less experienced labor, (2) deterioration in mechanical equipment and expendable material, and (3) increased contract prices. In the past, when there were more drilling rigs than wells to be drilled, some contractors would cut their drilling profit to keep their personnel and rigs working. As this practice is no longer necessary, the contract prices are adjusted upward to assure a profit. On deep and difficult drilling, contracts are let on a cost plus basis. A number of mechanical difficulties have become evident. Inferior quality of steel used in drill pipe and rock bits has added appreciably to drilling time and cost. Contractors are experiencing delay in obtaining repair work and repair parts for prime movers. As the length of drilling time required an shallow-field wells has not increased in proportion to that on deeper wells, it seems that the medium-sized drilling rig is better adapted mechanically than the heavy one to the work imposed. One of the main deficiencies in the heavy rig equipment is inadequate pump capacity. Drilling Mud The increasing amount of deep drilling has emphasized the importance and relationship of good mud to efficient and suc-

Jan 1, 1944

By Robert S. Dewey

AS a result of drilling operations during 1943, West Texas again added sufficient new oil reserves to replace the oil produced during the year, but failed to maintain its position in currently available reserves because the deeper discoveries will require years for development. Drilling failed to provide the additional oil necessary to meet the increase in current and anticipated market demand. Although 13.3 per cent of the total footage drilled was in wildcat exploration, the ratio of oil discoveries to total wildcats was less in 1943 than in 1942, but comparable to that in 1941. Of the 732 field wells completed, 270 were at Slaughter, 55 at Wasson, 45 at Mascho and 31 at North Cowden. As of Dec. 31, 1943, there were 361 drilling wells including 71 wildcat and 290 field wells; 19.7 per cent were wildcats. It is anticipated that the percentage of wildcats of the total wells will be higher during 1944 than in either 1942 or 1943. Tables 3 and 4 present a three-year comparison of drilling activity and illustrate the downward trend of development that has been in effect during that time. Because of development lag in the deeper Ordovician fields, several years elapse before 2 sufficient number of wells is completed to give a substantial producing rate. As these new oil reserves cost more to find, and will cost more to produce on a barrel basis than the oil marketed during the year, their reserve replacement value to the industry is less in money. Costs While complete costs for deeper drilling are not yet available for analysis, it is evi- dent from the data on drilling rates to comparable depths, contract prices, and general increases in costs, that the cost of drilling has risen approximately 20 per cent during the year. One representative drilling contractor estimates that the average drilling time on a 5000-ft. field well has increased nearly one third and that out-of-pocket costs have increased a dollar per foot. Three major factors contribute to this increased cost: (I) less experienced labor, (2) deterioration in mechanical equipment and expendable material, and (3) increased contract prices. In the past, when there were more drilling rigs than wells to be drilled, some contractors would cut their drilling profit to keep their personnel and rigs working. As this practice is no longer necessary, the contract prices are adjusted upward to assure a profit. On deep and difficult drilling, contracts are let on a cost plus basis. A number of mechanical difficulties have become evident. Inferior quality of steel used in drill pipe and rock bits has added appreciably to drilling time and cost. Contractors are experiencing delay in obtaining repair work and repair parts for prime movers. As the length of drilling time required an shallow-field wells has not increased in proportion to that on deeper wells, it seems that the medium-sized drilling rig is better adapted mechanically than the heavy one to the work imposed. One of the main deficiencies in the heavy rig equipment is inadequate pump capacity. Drilling Mud The increasing amount of deep drilling has emphasized the importance and relationship of good mud to efficient and suc-

Jan 1, 1944

By M. J. Beus, B. Stewart, S. Iverson

Ore-pass hazards are a significant safety problem in US underground metal mines. From 1975 to 1995, nearly 75% of injuries during pulling or freeing of ore-pass chutes were related to falls of broken rock or the use of hand tools. Risk assessment methods are being used to identify the most probable causes of ore-pass failures and analyse the factors that result in malfunctioning or safety reduction. Static and dynamic loads are being measured in the laboratory and by field testing, with data from test ore passes compared with mine data to characterise true system behaviour. Computer modelling using closed-form solutions, finite element analysis and a newly developed particle flow code are being use to predict loads from ore and waste flow and impact. Preliminary results indicate that dynamic impacts may be much less than expected, as a result of damping factors, normal and shear stiffness and mass frictional characteristics

Jun 19, 1905

By M. A. Amarante

Beneficiation studies were conducted on a Portuguese feldspar ore, in order to obtain final products capable of being used in the ceramic industry. A simple scrubbing operation is enough to break the lumps in the feed. The ore deposit contains ca 35 x 106tonnesfrom which, by screening, three main products could be obtained. This paper focuses on the beneficiation of the 500/74 µm fraction, which constitutes about 27% of the ore, assaying 9.42% Al2O3,equivalent to approximately ca 46% feldspar, with a mean iron content of 0.29% iron oxides. Magnetic separation and froth flotation testwork was carried out, in order to decrease the iron contamination and increase the feldspar content. Magnetic separation alone decreased the iron content of the feed to values between 0.04 and 0.08% iron oxides with an average yield greater than 90%. Flotation with HF, provided a feldspar recovery of 45?46% with a concentrate assaying 17.6% Al2O3. The use of H2SO4, gave a recovery of 35?36% of feldspar concentrate, assaying 16.1% Al2O3. However, economic and environmental advantages of using sulphuric acid may compensate for the lower mass recovery. The iron content of0.12% iron oxides in these concentrates, could be reduced to 0.04?0.05%, by further magnetic separation.

Jan 1, 1997

By A. M. Childs, R. F. Mather, K. R. Rawling

"The challenges encountered in the design and construction of mines and their process facilities today are becoming more intense and the engineering more competitive. The need to incorporate new techno1ogy to compensate for ever rising costs is always present, but its application in the harsh environment of Northern Canada increasingly requires the inclusion of new proven methods and innovative approaches to arrive at economically attractive projects.This paper deals with the development of the process design for the Cullaton Lake Gold Mine in the Northwest Territories. Particular emphasis is given to the interaction of the imposed construction and testwork schedules, and their effect on certain process decisions.The challenge that faced the project team may be defined by the following factors:1. A schedule which required that metallurgical testing, engineering, and procurement and delivery of all equipment and construction supplies should be complete within a period of ten months.2. Transportation of all personnel, equipment and supplies to the site by airlift, as no road was available or affordable.3. A six week period when transportation to the site was impossible.4. The extremes of temperature beyond the tree line in the Northwest Territories.5. A complete lack of infrastructure in the area."

Jan 1, 1983

By X. Q. Cao, D. S. Zhang, L. Q. Ma

To solve the support stability control problem for a coal face with large angles along both strike and dip (CLSD), the ’support-surrounding rock’ mechanical model has been developed, which takes into account the impact of the dip angle of the seam on the stability of the support in the strike direction. The mechanical relationships of the critical topple angle and critical slip angle of the support along the strike of the coal face with large dip angle and the support height, support resistance, friction coefficient, and other factors have been derived through the mechanical analysis of support stability in the strike direction of CLSDs in the free state, the operating state, and the special state. The research findings were applied to a fully mechanized CLSD in Xinji Coal Mine. The maximum underhand angle and overhand angle in strike are 42° and 25° respectively, and the maximum dip is 39°. It is calculated that during underhand mining and overhand mining, the critical support resistances for avoiding support toppling are 3723 kN and 1714 kN respectively, and the critical support resistances for avoiding slipping of the support are 7405 kN and 6606 kN respectively. Thus, the selection of type ZZ7600/18/38 hydraulic roof support for the coal face is justified. Measures to prevent sliding of the support and the installation of a limiting stop maintain the support runs in good condition and ensure safe and efficient mining of CLSD.

Jan 1, 2015

By S. V. Rungan

Since 1994, South Africa has been the subject of international attention, especially in regard to its transformation initiatives, which aim to redress the post-apartheid imbalances. Mining, as a major employer and one of the major industries in South Africa, has been the focus of the government?s Black Economic Empowerment initiative with the introduction of the Minerals and Petroleum Resources Development Act and the Broad?Based Socio?Economic Empowerment Charter for the South African Mining Industry. The historical background to South Africa?s transformation and the role of the mining industry are pivotal to an appreciation of certain aspects of the Minerals and Petroleum Resources Development Act and the Broad?Based Socio?Economic Empowerment Charter for the South African Mining Industry. The issues around Black Economic Empowerment and the enabling of a smooth transition to the South African mining industry of the future are explored in this paper.

Jan 1, 2005

By J. A. Meech, R. J. Tucker

"Since the establishment of froth flotation as an effective method of mineral beneficiation there has been both academic and industrial interest in the levels of the various reagents required to perform the desired separations. Academic interest was spurred by a desire to understand the mechanisms involved - industrial interest by a need to improve the efficiency of the process. These efficiency improvements can take two forms: cost reductions due to reduced reagent consumption and/or improved separation efficiencies. The latter are indicated by either improved grade-recovery relationships for removal of a valuable mineral from gangue, or improved separation of two similar valuable minerals.The processing of lower grade ore bodies at higher tonnage rates has necessitated increased interest in both reagent consumption and metal recovery. Furthermore, the development of accurate and functional on-stream analysis equipment in the 1960's and 1970's has allowed for a better understanding of the dynamic processes involved in a flotation circuit and has required a more concrete statement of the relationships and reactions between the minerals and chemicals in the flotation pulp. Development of these relationships is necessary in order to make use of on-stream analysis to control the process at, or near its more efficient level."

Jan 1, 1984

The Small Pebble Process for Reducing Ball and Power Consumption in Secondary Grinding Ball mills are used widely for secondary grinding. A mixture of ball sizes can be used to optimise grinding efficiency, but the use of balls smaller than about 30 mm in diameter is not normally viable, particularly when alloy steel is required. Preliminary testing of the grinding efficiency of various combinations of 40 mm steel balls and crushed stone in the size range 7 to 25 mm was carried out in a 300 mm diameter mill, which has accurate power measurement.The primary interest was to assess the potential benefit of adding small pebbles (from a primary circuit crusher or mill) to a secondary ball mill, to reduce ball consumption and to improve grinding efficiency. The optimum proportion of pebbles was found to be about 25 per cent by volume. This mixture produced about the same amount of fines as balls alone, but with lower power consumption, due to the lower density of the pebbles. The net result was a 12 per cent saving in power and a 25 per cent saving in ball consumption. The production of fines was partly due to pebble wear. The use of portions of 15 mm balls, (ceramic and steel), was also tested for comparison. A few batch pilot-scale tests were conducted in a 1.2 m diameter, 0.31 m long mill to test the viability of the pebbles at a larger scale. The pilot-scale tests confirmed the reduction in power and that the rate of production of fines was the same as that obtained with balls. The same residence time was used and this implies that pebbles can be added to an existing full-scale ball mill, with no loss in capacity. Samples of secondary mill feed and pebbles were obtained from a copper mine and the steady-state consumption of pebbles was determined by locked-cycle laboratory-scale tests. These tests demonstrated that mill power could be reduced by up 13 per cent and that the consumption of 40 mm balls could be reduced by up to 38 per cent, while maintaining the same throughput and product size. The rate of pebble addition was about 4 per cent of the primary circuit feed rate. Application has been made for patent protection.

Sep 13, 2010