Search Documents

By Jie Li

Series of carbon compounds as anode materials were prepared for super lithium ion capacitor using graphite and active carbon (AC) as raw materials. Their electrochemical properties were investigated by constant current charge-discharge test. The results showed that the compound anode had good capacitive performance as well as Li-ion battery performance. The potential of the capacitor could be as high as 3.5V vs Li/Li+ when compared with 2.5V vs Li/Li+ in the AC-AC capacitor, accordingly, the energy density increased from 21.7Wh/kg to 40.3Wh/kg. The compound anode also had excellent rate performance that as the current density increasing from 0.1A/g to 1A/g,the capacitance decreased only 1.3F/g, and good cycle performance that the capacitance holding remained 96.7% after 10 times cycles even at the highest potential of 3.5 V vs Li/Li+.

Jan 1, 2009

"Chairman: Professor J. Elbrond Rapporteur: Miss V. E. MartingPapers.Aids to planning production in coal mines by F. H. Deist and M. P. RobertsCapacity calculations, investment allocation and long-range production scheduling in German coal mines by F. L. WilkeOre reserve evaluation and open pit planning by J. M. Marino and J. P. SlamaThis session was devoted to the economic aspects of planning and scheduling. After Dr F. H. Deist had introduced the paper Aids to planning production in coal mines, Dr T. V. Falkie summarized the following formal contribution prepared jointly with Dr R. V. Ramani, describing the work that has been done at the Pennsylvania State University in the development of simulation programs for mine planning over the past 15 years:During the late 50's and early 60's, Monte Carlo simulators were developed to model continuous miner-shuttle car transport systems, track haulage systems, belt conveyor networks, etc. In the mid-60's attention was directed towards deterministic simulation of equipment performance, given the equipment characteristics and the system profile. In the late (10's all these systems (miners, shuttle cars, belts and trains) were integrated together to form a complete coal mine simulator and the program could predict the output potential of the system, given the mining dimensions, method and equipment employed. The actual sequence of coal-cutting operations is entered into the computer through the use of a special programming language which permits any type of mining configuration to be simulated. The simulator is hybrid in nature in that the shuttle cars, trains and belts are simulated deterministically, whereas rate functions with delay frequencies are entered for the continuous mining operations of sumping, shearing, fleeting, cleaning, etc. With suitable manipulation of the data, the program may be applied to all belt or conventional mining sections. Most of these simulators were developed through the assistance of grants from the Department of Mines and Mineral Industries of the Commonwealth of Pennsylvania and are available from the Coal Research Board of the Commonwealth,"

Jan 1, 2014

By F M. Weir, M Fowler

A discrete fracture network (DFN) approach involves numerical modelling that explicitly represents how defects may be spatially distributed through a rock mass. A DFN is a 3D realisation of the ‘smaller scale’, non-deterministic defects; it is not an attempt to model larger, deterministic structures that should be identified as part of an engineering geology model. The approach utilises structural data in stochastic analyses to give a range of possible models that provides a tool for visualisation and analysis of a rock mass and indicates the potential large-scale slope or tunnel performance and stability.Stochastic fracture modelling for rock mass characterisation has significantly advanced over the past 25 years. With recent improvements to field data collection and computational power, it has become recognised internationally as a valuable tool for modelling some geomechanical problems encountered when designing excavations in fractured rock masses.This paper provides an introduction to the DFN approach, particularly the necessary input parameters and derivation of these from typical structural data sources, such as boreholes or scan line mapping. Of particular importance for engineering applications is validation of the simulated fracture network and techniques for doing so are discussed here.CITATION:Weir, F M and Fowler, M, 2014. An introduction to discrete fracture network modelling and its geotechnical applications, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 435–444 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By Elliott A, Kingsnorth D. J

The development of a large high grade spodumene orebody, in excess of 30M tonnes containing at least 7M tonnes at 4.0% Li20, by Lithium Australia Ltd at Greenbushes, Western Australia is significantly increasing the world consumption of lithium minerals. The availability of two low cost sources of lithium, spodumene concentrates (7.5% Li20) and glass grade spodumene (4.8% Li20) has been welcomed by the ceramic and glass industries as it assists them to lower their raw material costs at a time when they are facing severe competition from alternative materials. While there is no shortage of lithium reserves in the world, there has been a shortage of high quality lithium minerals. The Lithium Australia development has filled this need. The favourable factors of high grade, low impurities, open cut mining and existing infrastructure make this an ideal low cost source for a long term downstream lithium industry. The Lithium Australia mine development has filled the need for a reliable long term supply of lithium minerals. The long term viability of this resource is ensured by the unique combination of the following key attributes of the development : High grade reserves of 7.OM tonnes of 4.0% Li20 within 130 metres of the surface, contained within a total proven reserve of 30M tonnes of 2.8 % Li20. Open pit mining with stripping ratio of less than 2.5:1 waste:ore. Low impurities levels, particularly in those elements, that have a detrimental effect on the colour of glass/ceramics i.e. iron, manganese, titanium and chromium. An existing mine infrastructure that includes an adequate water supply for all foreseeable processing requirements. A sophisticated spodumene concentrator utilizing statistical process control to produce a consistently high grade product with minimal impurities. A technically qualified stable workforce fully acquainted with spodumene processing techniques. Greenbushes high grade concentrates have found ready acceptance in the specialty ceramic and glass industries during the past four years. The consistency and high grade/low impurity level of the product has enabled its use in the production of television tubes, oven to table ware, glass fibres, specialty glasses and ceramic glazes.

Jan 1, 1989

By N. H. J. Freire, D. Majuste

In this paper, the effects of some organic compounds on the current efficiency, cell voltage and specific energy consumption during nickel electrowinning, and on the deposit features (morphology, crystallographic orientation and nanohardness) were described. The organics tested here (extractant, diluent, flocculant, lubricating oil and acid mist suppressant) are currently used in industrial plants. The results indicated that only the flocculant and acid mist suppressant exhibit relevant negative impacts on the current efficiency and energy consumption. The current efficiency dropped from 93.6 % (organic-free solutions) to 86.0 % and to 92.8% in electrolytes containing 100 mg.L-1 of acid mist suppressant and flocculant, respectively. At this concentration, their addition to the electrolyte led to increases of the specific energy consumption in the order of 18 % (acid mist supressant) and 2 % (flocculant). Cyclic voltammetry showed that Ni nucleation occurs at more negative potentials at 50 and 100 mg.L-1 of these organics in the electrolyte, thus indicating an inhibition of the deposition process. The deposit quality decreased at the higher concentration of all organics, when more hydrogen pitting was observed. The acid mist suppressant caused delamination of the Ni deposit at 50 and 100 mg.L-1. The addition of 100 mg.L-1 of flocculant and acid mist suppressant to the electrolyte increased the nanohardness of the deposit around 31 and 72%, respectively. The increase in Ni deposit hardness may lead to a decrease in the material ductility, thereby affecting the stripping and cutting of Ni sheets. Our findings may be helpful since strong adverse effect of some organics that may be present in the electrolyte were identified, thus the industry can control and optimize the organic´s dosage in the corresponding operations.

Jan 1, 2016

By M. G. Wallis

This report presents the results of a study to develop a detailed mining method design based on longwall mining with sublevel caving. The method is applicable to low-dipping coal seams 20 or more feet thick such as are found in the western United States. The report covers (1) the development and description of the mining method, (2) evaluation of the engineering feasibility of the design, (3) estimates of productivity and recovery, and (4) an engineering cost analysis and economic feasibility evaluation of the mining method design.

Jan 1, 1977

By James P. Sloss

A PERMANENT assay office is commonly established as part of the general plant equipment of operating gold and silver properties, but during the development stage of a mine, the cost of such an office is usually so assay work must be done elsewhere. In most instances only a few samples will be taken each day, but if the mine is to be developed scientifically, the analyses of those samples will guide further development. Under such circumstances, the time element in assay returns is important, since the lapse between the taking of the samples and the receipt of results may determine the success or failure of a small-mine operator. The following description of fur-

Jan 1, 1935

The 107th Annual General Meeting of The South African Institute of Mining and Metallurgy was held at The Country Club, Johannesburg, Napier Road, Auckland Park on Wednesday, 11 August, 2004. Welcome The President extended a special welcome to the guests and representatives of our sister institutes and other associations, also to recipients of awards, senior members of industry, Honorary Life Fellows, past-presidents, our members and other guests, among them the following: Ralph Bagirathi, Executive Member, African Mining Association Rudi Rudolph, President, Association of Mine Managers of South Africa Andrew Whibley, President, Association of Mine Resident Engineers of South Africa Dr Con Fauconnier, President, Chamber of Mines of South Africa Nxolisi Diliza, Chief Executive Officer, Chamber of Mines of South Africa

Jan 1, 2004

By H Arvidson, V Chamberlain, J Joughin, N Pollock, F Cessford, T Flitton, T Rowl

Environmental, social and governance issues (ESG) have become a defining feature in the marketplace to differentiate preferred investments. With the sustainability commitment and reporting landscape anticipated to evolve exponentially, it is now imperative to rapidly develop the approach taken by mineral companies to adequately identify and address ESG risks and opportunities in the reporting of Mineral Resource and Mineral Reserve (MRMR). MRMR cannot be effectively reported as technically and financially assured and realistically executable, if ESG is not integrated into the strategy, business model, input assumptions and process that defines and drives robust MRMR public reporting. Regulatory reporting codes across the globe are presently in various stages of being updated and modified to ensure ESG factors are appropriately covered as a key part of diligent and transparent disclosure. Security exchanges are making it clear that companies must not omit ESG risks from reports to investors. This paper discusses associated challenges for MRMR reporting and suggests avenues for improvement. Key themes include: the importance of procedure rather than prescription and checklists; how ESG criteria impact Modifying Factors and determination of Reasonable Prospects for Economic Extraction (RPEE); the need for financial models to account for material ESG commitments; the uniqueness of each mineral asset; the need for education, upskilling and accreditation of both ESG experts about MRMR reporting and equally Competent Persons in ESG matters; and the need for clear and balanced reports that meet the needs of end users. (RPEE is adopted here for simplicity and consistency, recognising that some reporting codes still include ‘Eventual’ in the term (ie RPEEE). Whilst RPEE and RPEEE are subtly different the intent is to point to the process of assessing ESG factors in determining reasonable prospects.) The principles of transparency, materiality and competence remain paramount when considering the impact of ESG matters on MRMR reporting, and this necessitates an inclusive, cohesive, and integrated approach to assessing ESG issues to ensure the necessary expertise and diligence is applied.

May 24, 2023

By Kenneth E. Hay

Researchers from the U.S. Bureau of Mines conducted a field study to assess the safety of remotely controlled mobile roof supports (MRS) in a retreat pillar mining operation, Data were collected to provide the Mine Health and Safety Administration with criteria needed to develop guidelines for MRS use and to determine if precursors could be identified that would alert miners to imminent roof falls. Two test sites at which two different support methods-MRS's and posts were used and were monitored to obtain information on entry stability. Pressure transducers and string pots were installed on all four MRS's to obtain loading and displacement information. and roof bolt load cells. sonic probes, extensometers, and survey targets were installed in the surrounding entries to obtain information on ground behavior. Results showed a larger increase in roof bolt loading and roof movement when MRS's were used, especially in the intersection area. Roof bolt loads in the entries showed decreases in load when the MRS's were set and increases up to 11,1 kN (2,500 lbf) when the MRS's were unloaded. Unloading of one MRS in a pair did not significantly increase load on the other. MRS's I and 2 usually had the higher loads, with these loads increasing as the pillars on each side were being mined. MRS 3 normally had lower loads than I and 2: however, it also experienced some very high loads when in the last position near the pushout. MRS 4 usually had the lowest loads, primarily because it was located near the solid pillar that was not being mined.

Jan 1, 1995

In recent years there have been many changes in mine ownership due to the on-going rationalisation towards larger mining companies. Larger companies inevitably find it hard to manage small mining operations and in many cases smaller mines do not fit corporate resource, production and profit criteria. Smaller companies are more suited to managing these medium or small scale mines and are tendering for the purchase or lease of mines that larger companies wish to dispose of. In addition to these factors there has also been a trend (especially in Western Australia) for mines to continue operating at ever increasing depths. This in turn has led to more mines operating in high stress environments and experiencing damaging seismicity. Assessing the viability of seismically active mines from a takeover or purchase point of view should involve analysing the risk profile of every aspect on mining that could be affected by adverse seismicity. This includes assessing current and alternative mining methods, mine designs, support systems, extraction sequencing, monitoring and blasting. This paper includes discussion on items that need to be assessed when considering the purchase of seismically active mines, with experience gained from some recent studies in Western Australia. In these cases it was apparent that quantification of previous seismic history on itÆs own was a totally inadequate method of assessing minewide seismic risk potential. A more holistic approach is required, taking into account all aspects of relevant data, all the minewide effects of seismic activity and all possible means of mitigating those effects.

Jan 1, 2002

By Marlion T. McQuinn

This paper will discuss the design, construction, and performance of the support of excavation on the Dulles East and West Automated People Mover Tunnels and Station projects. The elements of the system included drilled soil nails and rock anchors with reinforced shotcrete to the excavated face. We will discuss the geotechnical characteristics, design and construction considerations, loading criteria, construction techniques, schedule constraints, and performance of the support of excavation system. In consideration of the conference theme, there will be a discussion of the application of the real-time instrumentation monitoring program. The project team worked to design and install approximately 710,000 square feet of shotcrete and 19,000 soil nails/rock anchors as well as excavate over 720,000 cubic yards of rock materials within 15 months and in such a manner as to minimize the disruption to airport passengers and operations.

Jan 1, 2006

By Richard E. Thill

The Bureau of Mines' Oil Shale Data Bank (OSDB) was created in 1976 to serve as a centralized source for the storage, retrieval, and dissemination of technical literature, patents, and information on research projects in oil shale. Thousands of bibliographic references, patents, and research projects relating to the mining of oil shale have been identified, abstracted, and indexed according to selected keyword topics. The resulting data bank listings are contained in three sections, each with a separate keyword breakdown for use in rapidly identifying references pertaining to a specific subject. All references cited in the OSDB were published prior to an established cut-off date of May 1, 1981, when a redirection of Bureau of Mines programs resulted in the loss of project funds and the subsequent phasing-out of data bank operations. ACKNOWLEDGMENTS The oil shale data bank listings are the result of a team effort of the project staff. The contributions of Jimaleen Jansma for keypunching, information acquisition, and data entry, and John Brandenburg and Sandra Brake for keywording and information acquisition are gratefully acknowledged. Appreciation is expressed to the staff members of the Smithsonian Science Information Exchange, Washington D.C. for their cooperation in supplying data on recent research projects in oil shale for inclusion in the OSDB listings. Appreciation is extended also to the staff of the Gallegos Research Group for assisting with computer services to obtain the final printouts and transfer of files onto magnetic tape.

Jan 1, 1982

By N. R. Paterson, D. G. MacKay

"The geology of the Mattagami mining camp, while of particular economic significance, is unfortunately obscured by a very thick mantle of overburden. For this reason geo-physical methods have been relied upon heavily in exploring the area. Geophysical data over five important sulphide discoveries show how targets are selected for drilling and how effective geophysics has been in assisting subsequent development programs."

Jan 1, 1960

This Kaiser Engineers report on the feasibility of surface mining on the North Slope of Alaska has considered the quantity and quality of the North Slope deposits with attention paid to the economic, technical, and environmental constraints of the mining systems suggested for the three candidate minesites at Kukpowruk River, Elusive Creek, and Kuk River. Site selection, based on coal rank and quality as well as seam thickness and geometry, also considered demonstrated and hypothetical reserves relative to three mining systems (dragline, shovel, dragline and shovel), mining equipment requirements, infrastructure, and transportation relative to the Arctic environment and costed for potential markets. Throughout the report the delicate permafrost environment has received particular consideration. Recommendations based on the technical, economic, and environmental feasibility of mining the coal deposits of Northern Alaska by surface mining techniques have resulted in two conclusions: 1. The coal deposits can be mined with currently available technology; 2. It is uneconomic to mine these coals given current coal resource estimates, costs, and market conditions. A literature survey is included in appendix.

Jan 1, 1977

Previous published papers by Fraser (1), Hey (2), and Stillwell (3), have given respectively, details of:-1. The practice in the pilot plant operated at Zeehan for the treatment of ores from the Rosebery field.2. The design, based largely on the experience gained at Zeehan, of the concentrator built at Rosebery.3. The nature of the orebodies of the zinc-lead lode at Rosebery.Changes and developments, at the Rosebery concentrator, since operations commenced, are now described with particular reference to recent practice.Three concentrates are produced, viz.: a copper, a lead, and a zinc concentrate. The current flow-sheet is shown in Fig. 1. Typical concentrate assays are...THE OREThe ore treated is derived from the Rosebery and Hercules Mines and is, milled in the ratio of, approximately, two parts of the former to one of the latter. The ores from the two mines may be considered as being similar in general character, although the Rosebery ore contains more pyrite. It is from this mine that any increased tonnage is expected. The ore is a mass of fine-grained, intimately associated sulphides, with practically no coarse...

Jan 1, 1949

By J. Sikamo, A. Mwanza, C. Mweemba

"The Zambian copper mining industry as we know it today had its genesis in the 1920s. Consistent private sector-driven investment in the industry over a period of over 50 years in exploration, mine development and operation, development of minerals processing facilities, building of infrastructure for pyrometallurgical and hydrometallurgical processing, with attendant support facilities, including building of whole new towns, resulted in copper production rising to a peak of 769 000 t in 1969, providingover 62 000 direct jobs. The industry was nationalized in 1973 and remained in government hands for just over 24 years. During this period, the industry experienced a serious decline in production levels, reaching the lowest level in the year 2000 when production was 250 000 t. An average of just under 2000 jobs were lost every year in the 24-year period, reaching just over 22 000 direct jobs in 2000.Following the return of Zambian politics to pluralism and liberalized economic policies, the government decided to privatize the mining industry. The process started in 1996 and by the year 2000 all the mining assets had been privatized. The new investors embarked on serious investment to upgrade the assets and to develop greenfield mining projects. Fourteen years later and after more than US$12 billion investment, production levels increased year-on-year to a peak of 763 000 t in 2013 with direct jobs reaching 90 000.This paper discusses the impact of the mining industry in Zambia on the economy in areas such as employment, support for other industries, direct contribution to the national gross domestic product (GDP), foreign exchange earnings, and social amenities. The paper also focuses on the performance of the mines during these periods vis-à-vis mineral availability, mineral grades and complexity, new technologies, and human capital. This is looked at particularly in the light of current challenges the industry is facing. Suggestions are proposed on how the industry can be nurtured to continue being a major driver for the Zambian economy and a major player in the international copper mining business."

Jan 1, 2016

By P Shen, K Hattori, H Pan, E Seitmuratova

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Ore-bearing intrusions in the Central Asian Orogenic Belt (CAOB) were examined from nine mines: Boshekul, Nurkazgan, Kounrad, Borly, Aktogai, Koksai, Baogutu, Tuwu and Erdenet. The intrusions are diorite, granodiorite and tonalite with SiO2 contents ranging from 58 to 75 wt per cent, and show mildly fractionated rare earth elements (REE) ([LREE]N/[HREE]N = 2.7–4.7) – light REE and heavy REE – and varying Eu anomalies ([Eu]/[Eu]* = 0.58–1.4). The ratios of Sr/Y vary from 7.9 to 115 and the contents of Y from 4.6 to 23.9 ppm. The parental magmas of the intrusions are intrinsically oxidised. Zircon grains in the ore-bearing rocks from large- and intermediate-sized porphyry Cu deposits show high Ce4+/Ce3+ ratios characterised by 65–422 at Boshekul (>4.1 Mt Cu), 76–480 at Kounrad (>4.8 Mt Cu), 90–280 at Aktogai (>12 Mt Cu), 80–250 at Erdenet (>11 Mt Cu) 74–370 at Nurkazgan (>3.9 Mt Cu), 100–210 at Koksai (>1.6 Mt Cu), and 71–340 at Tuwu (~2.0 Mt Cu). In two small deposits, the ore-bearing rocks display low values of Ce4+/Ce3+; Borly (0.6 Mt Cu) ranging from 28 to 158, and Baogutu (0.6 Mt Cu) from 29 to 113. The Ce4+/Ce3+ ratio of 120 distinguishes large intermediate-size deposits from small-size deposits. This information is potentially useful in exploration for porphyry Cu deposits in the belt.CITATION:Shen, P, Hattori, K, Pan, H, Jackson, S and Seitmuratova, E, 2015. Granitoids associated with porphyry Cu deposits in the Central Asian Orogenic Belt – characteristics and oxygen fugacity, in Proceedings PACRIM 2015 Congress, pp 377–382 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By K. Delbeke

Within the framework of the EU Existing Substance (93/793/EEC) and REACH regulations EC/1907/2006), the copper industry initiated in 2000 a comprehensive Voluntary Risk Assessment of copper and several copper compounds. The Italian Government's Istituto Superiore di Sanità, reviewed the process and reports on behalf of the European Commission. Copper exposure levels to man and the environment from production of copper anodes and cathodes, copper powders and copper chemicals as well as fabrication and use of semi-fabrication products and down stream user products were collected across Europe. Environmental and human health effects data were obtained from literature as well as novel research programs and used to deduct safe threshold

Jan 1, 2007

By Joseph Jensen

MANY fields have been zoned by nature with shales and intermediate waters between oil zones. Limitations thus imposed have been the basis on which the field was developed. In contrast thereto, in the Ventura Avenue Field, nature proved more generous. Always expecting to find such similar limitations, operators drilled deeper and deeper into the oil zone without finding any distinctive shale bodies other that the Gosnell shale and only one intermediate water, which became the point below which the final water shut-off of each well was made. Thus, on top of the structure, about 3300 ft. of oil-bearing zone has been penetrated below this intermediate w9ter-a distance of 4000 ft. below the Gosnell shale. At first it seemed that the greater the penetration in the zone, the better the well. The error of this assumption became evident

Jan 1, 1930