Search Documents

By T. M. Barczak

A primary objective of the Bureau of Mines geomechanics research program is to develop a better understanding of support behavior and interaction of supports with the strata so that supports can be more closely engineered to the geological conditions in which they are employed. Four longwall shield supports were instrumented with an eight-transducer instrumentation array to measure leg, canopy capsule, and compression lemniscate link forces from which resultant shield loading was determined. The instrumented supports were monitored over a 4-month period, producing over 75 shield cycles of resultant shield loading. Resultant loading is the true measure of support resistance, providing both roof-to-floor and face-to-waste support reactions as well as the location of the reaction on the shield canopy. Observed roof support reactions were analyzed, with particular emphasis on horizontal shield loading, since it is the least understood design parameter. Average, peak, and change in shield loading during the mining cycle are discussed. Correlations among data parameters are examined, as is the distribution of support loading at the headgate and midface. Conclusions are drawn as to the effectiveness of the shield support at this installation. Recommendations are made for further research needs.

Jan 1, 1987

By J. D. Steenkamp

Keywords: Thermal, conductivity, diffusivity, expansion, history, density, specific heat capacity, industrial rich high-carbon manganese slag The thermal conductivity of slag is an important parameter in the design of furnace-containment systems based on freeze-lining technology. Literature indicates that the crystal content of a slag has a significant influence on its thermal conductivity. Industrial, rich, manganese-bearing slag was cooled at different rates to create samples with different microstructures. The coefficients of thermal conductivity of these samples were measured in a nitrogen atmosphere from room temperature to 990°C at 100°C intervals. The laser-flash measurement technique was used for this purpose. Follow-up investigations included XRF and XRD and modelling in FACTSage.

Jan 1, 2011

By Richard Dahl, Richard P. Taylor, David H. Watkinson

"Abstract - Detailed mapping of the Eastern Gabbro, Coldwell Complex, Ontario, revealed that the copper and platinum-group-element deposit on the Marathon property is confined to a coarsegrained to pegmatitic gabbro-diorite intrusion, the Two Duck Lake intrusion (TDLI). Exposed along the eastern boundary of the Coldwell Complex, the TDLI was emplaced as a sill whose orientation is slightly oblique to the general structure of the Eastern Gabbro. The TDLI has been subdivided into lower, middle and upper sub-units on the bases of lithological, textural, mineralogical, and geochemical criteria. Both border sub-units are sulfide-, base- and precious metal-enriched, and exhibit abundant evidence of host-rock assimilation. The primary mineral assemblage in the TDLI is plagioclase, olivine, clinopyroxene, Fe-Ti oxides, with accessory orthopyroxene, biotite, apatite; this primary mineral assemblage is essentially preserved in the core of the intrusion (i.e., the middle subunit). The Cu-PGE Marathon deposit, delineated mainly in the upper sub-unit of the intrusion, consists of disseminated Fe-Cu-Ni sulfides, and platinum-group-minerals derived by hydrothermal remobilization from primary magmatic sulfides. Enrichment in Cu and PGE resulted from partial replacement of original Fe-Ti oxides and pyrrhotite in the primary mineral assemblage by reaction with (a) residual magmatic fluid, and (b) fluids derived from the breakdown of host rock xenoliths and hydrothermal alteration along the lower contact of the TDLI. Résumé - La cartographie détaillée de l’Eastern Gabbro, Complexe Coldwell, en Ontario, révèle que le gisement de cuivre et éléments du groupe du platine de Marathon est confiné à une intrusion gabbro-dioritique, de grain grossier à pegmatitique, l’intrusion Two Duck Lake (TDLI). Cette intrusion s’est mise en place sous la forme d’un filon-couche légèrement discordant sur la structure de la bordure orientale de l’Eastern Gabbro. On y distingue trois sous-unités, inférieure, centrale et supérieure, sur la base de zonations lithologique, minéralogique et géochimique. Les sous-unités marginales sont enrichies en sulfures, métaux usuels et précieux, et montrent de nombreux indices d’assimilation des roches hôtes. La paragenèse minérale primaire inclut le plagioclase, l’olivine, le clinopyroxène, les oxydes ferro-titanés et accessoirement et localement, l’orthopyroxène, la biotite et l’apatite : cet assemblage est surtout préservé au coeur de l’intrusion (sous-unité centrale). Le gisement de Cu-EGP de Marathon, situé principalement dans la sous-unité supérieure, comprend une minéralisation disséminées à sulfures de fer, cuivre, nickel, et minéraux du groupe du platine, dérivés de sulfures magmatiques primaires par remobilisation hydrothermale. L’enrichissement en Cu et EGP résulte du remplacement d’oxydes ferro-titanés primaires par réaction avec des fluides tardi-magmatiques, et des fluides assimilés le long de la bordure inférieure de l’intrusion, dérivés de la fusion partielle des xénolites et de remobilisations hydrothermales."

Jan 1, 2001

By Marshal Scherba

Coal seams approximately 7 feet, 9 feet and 20 feet thick at depths of 250, 600 and 1,000 feet respectively were detected using high resolution seismic reflection techniques. Investigation of seismic profiles indicates that good data are required to delineate faulting with only 20 feet of throw but that faulting with 50 feet of vertical displacement can be detected with poor data. Data acquired from dynamite charges fired in water saturated media were clearly superior to that acquired using charges dry tamped in 10 and 20 foot holes.

Jan 1, 1977

By Reed Thorne

To many people, rescue from elevated, sometimes vertical, locations brings about thoughts of heroism mixed with brawn and self-sacrifice. Images are conjured of cliff rescues where the technical effort is hanging from a few seemingly small nylon ropes hundreds of feet above the ground. Such is the vertical realm of technical rope rescue. This is a technical field in which the author serves professionally as battalion chief of (rope) operations for a northern Arizona fire district, and as a private sector instructor to mines in the United States and Canada.

Jan 1, 1996

By M. D. Budeba

Determining the efficiency of a surface coal mine operation is an essential activity, which can help in deciding on the optimal use of input resources, including effective capital allocation, in generating a desired quantity of coal of a specific quality. Mines operate today in challenging conditions, with diminishing reserves of high-quality coal, remote location of new coal deposits, infrastructure problems, environmental legislation, and the effects of climate. All these have an impact on the performance of a mine. Given such challenges, a company has to be technically efficient compared to other existing coal producers in order to generate profits. It can use the measurement of its efficiency to evaluate its productivity, benchmarking this against the best-performing mines and determining optimal variables in order to minimize slack and achieve the desired outputs. This paper discusses the use of Data Envelopment Analysis (DEA) in evaluating the efficiency of a surface coal mine supply chain for the coal export market. The supply chain is considered to be composed of subprocesses that are modelled as a multistage system. Numeric examples will be used to illustrate the application of DEA.

Jan 1, 2014

By P. Ashayer, J. Curran

Introduction Rockfalls occur when rocks or boulders detach from mountains or hills and tumble down. They can pose significant hazards to infrastructure such as highways, buildings, and mine open pits, and they sometimes result in personal injury or death. Prediction of rockfalls is a difficult task. Slopes that are at risk of rockfall have highly variable geometries. The location, mass, and shape of the rocks that might dislodge and fall are uncertain. Moreover, the materials that make up a slope can vary considerably from one section to another. Furthermore, the relevant material properties are usually not well known. Performing probabilistic simulations of rockfalls, combined with proper statistical analyses, has proven to be an effective and acceptable method for dealing with these difficulties [1, 2, 3]. The movements of a falling rock can be classified as freefall, bouncing, sliding, toppling, or rolling. The falling trajectory is controlled mainly by the geometry of the slope, the block shape, and the energy dissipated at each contact of the block with the slope. A rockfall model is evaluated based on its ability to efficiently predict the velocity, frequency, height of bounce, and run-out distance of falling rocks. With this information, the engineer can design remedial measures such as restraining nets and ditches. Most of the existing rockfall simulators are based on particle models that consider the falling rock as an infinitesimal particle with a mass, called the lumped mass or stereomechanical models [1, 2, 3, 4]. Other models involve hybrid methods relying on simplified assumptions. The most common hybrid methods are based on contact searching for the movement of a dimensionless object and incorporate some aspects of rigid body impact for bouncing [5, 6, 7]. There are also some rigid body models in the literature that employ simplified versions of rigid body models [8, 9]. This study applies a more sophisticated rigid body theory based on rigid body impact mechanics (RBIM), which was developed by Stronge [10, 11, 12]. The new theory captures all modes of rigid body movement. Due to the importance of the rock geometry, single impacts of ellipsoidal and prismatic rocks with rectangular cross sections are investigated. The effect of rock slenderness on rebound velocities and energies is also investigated for ellipsoidal rocks. The correspondence between the model parameters and the data from the rockfall literature data will be discussed.

Jan 1, 2007

By G. Roger Miller, Kristine M. Krajnak, Stephen S. Leonard, Stacey Waugh

Repeated exposure to hand-arm vibration through the use of vibrating hand tools can result in the development of the disorder known as hand-arm vibration syndrome (HAVS; (1,3)). One of the hallmark symptoms of HAVS is cold-induced peripheral vasospasms that result in finger blanching (4). Although the vascular and neural pathology associated with vasospasms has been described, little is known about cellular mechanisms leading to this damage (4). To understand how vibration may alter vascular and neural physiology and anatomy, rats were exposed to a single bout of tail vibration and the molecular responses of neural and vascular tissues were measured to determine if there are immediate or sustained affects of vibration that may underlie longer term changes in physiology. Methods Experiment 1. Male Sprague Dawley rats (n = 32, 6 weeks of age) were housed in AAALAC accredited facilities. All procedures were approved by the NIOSH Animal Care and Use Committee and were in compliance with the CDC guidelines for care and use of laboratory animals. Vibration exposures were performed by restraining rats in Broome-style restrainers, and securing their tails to a vibration platform using 6 mm wide straps that were placed over the tail every 3 cm. Restraint control rats were treated in the same manner, except that the tail platform was mounted on isolation blocks and not on a shaker. The vibration exposure was 125 Hz, 49 m/s2, for 4 h. Rats were euthanized with an overdose of pentobarbital (100 mg/kg) 1 h or 24 hours after the exposure. RTqPCR was used to measure transcript levels for endothelin 1 (ET-1), the 3 forms of nitric oxide synthetase (NOS) NOS-1, NOS-2, NOS-3 and norepinephrine receptor subtypes 1D, 2A, 2C, in artery tissue, and to measure calcitonin gene-related peptide (CGRP) and nitric oxide synthase-1 (NOS-1) in ventral nerves. Data were analyzed using 2-way ANOVAs. Experiment 2. Male Sprague Dawley rats (n =24, 6 weeks of age) were maintained as described above. Animals were exposed to a single bout of restraint or vibration. Another group of animals served as cage controls. All animals were euthanized 24 h after the exposure, and tail arteries were isolated and frozen. Reactive oxygen species ROS) were measured using electron spin resonance spectroscopy (ESR). Arteries were homogenized over ice in 1 ml of PBS with protease inhibitor cocktail, using a tissue tearer (Biospecs Products Inc. Racine, WI USA). The sample was split into two 0.5 ml samples. One set had PBS and the spin label hydroxyl-TEMPO [0.1 mM] added while the other set had hydroxyl-TEMPO [1.0 mM] plus the specific hydroxyl radical scavenger, dimethylthiourea (DMTU), added to confirm the presence of the hydroxyl radical. Samples were vortexed and then placed in a flat cell for ESR analysis. The ESR spectrometer settings were: receiver gain, 6.32 x 102; time constant, 0.02 s; modulation amplitude, 1.0 G; scan time, 20 sec; magnetic field, 3490 ± 100 G (2). Data were analyzed using 1-way ANOVAs.

Jan 6, 2006

By Jacqueline A. McClaskey

The U.S. Bureau of Mines (USBM) Information and Analysis Directorate collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The USBM's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the USBM survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress). This act strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1995

By N. E. Hanna

An investigation was made of pressure pulses produced by unconfined explosive blasts in underground openings. Four tests were made with TNT or modified amatol charges ranging in weight from 60 to 2,000 pounds; each test involved either single or multiple charges. Pressure-time profiles were obtained using mechanical self-recording pressure gages. The cube-root scaling law for peak pressure was found to be valid within about 1 tunnel diameter; at greater distances, the pressures obtained along direct paths were generally higher than this scaling law would indicate.

Jan 1, 1968

By R. R. Falier, W. E. Rice

"PURPOSE OF REPORTThis paper presents the results of a series of tests made by the U. S. Bureau of Mines in cooperation with The Ohio State University Engineering Experiment Station as part of an investigation on the use of fuel in kilns.This report is preliminary and gives only enough of the test data to illustrate results and show the reasons for the successes and failures of the method of firing investigated; fuller details will be included in the final report.PERSONNEL FOR TESTSThe investigation is conducted under supervision of P. Nicholls, supervising fuel engineer, of the United States Bureau of Mines, and G. A. Bole, research professor, of The Ohio State University. These tests were made under direction of W. E. Rice, associate fuel engineer, assisted by R. R. Faller, assistant fuel engineer, of the United States Bureau of Mines; H. C. Harrison, senior research engineer (until October 1, 1930), C. R. Austin, senior research engineer (since October 1, 1930), and H. K. Van Sohoick, junior research engineer, of The Ohio State University. M. J. Rice, field engineer, represented the manufacturer of the stoker.PURPOSE OF INVESTIGATIONThe general aim of the investigation is to develop more economical methods of using fuel in kilns and to improve the over—all efficiency of the process of firing by methods that will produce ware of better quality. One phase of this investigation is the burning of coal on an automatic stoker to gain the advantages of control, constant rate of application of heat, and ability to burn cheaper coal than can be used in the hand—fired furnaces of kilns. It a stoker in to be used it is desirable that the coot of the installation should be low, the control of operation simple, and the distribution of heat in the kiln as good or better than with hand firing. These desiderata were sought in the stoker and furnaces that were used for the tests described herein. The tests were made to determine whether it is feasible to fire a large kiln with a single stoker, whether the use of a single furnace simplifies control, and whether the admission of all the hot gam at the center of the kiln will give symmetrical distribution of heat."

Aug 1, 1931

By W Valery, S Morrell

In the mining industry blasts are usually designed to fracture the in situ rock mass and prepare it for excavation and subsequent transport. The run of mine (ROM) fragmentation is considered good when it is fine enough and loose enough to ensure efficient digging and loading operations. Mining optimisation strategy is hence usually focussed on minimising total mining costs and maintaining these ROM fragmentation characteristics. Although this approach ensures an efficient mining operation it ignores the potential impact on crushing and grinding. Investigations by several researchers have shown that designing blasts to produce ROM fragmentation to optimise crushing and grinding performance enhances the overall efficiency and profitability (Eloranta, 1995; Kojovic et al, 1995; Bulow et al, 1998; Kanchibotla et al, 1998; Scott et al, 1998; Simkus and Dance, 1998). Field experimentation in this area is often found to be difficult because of high implementation costs and insufficient understanding about the effect of fragmentation at different stages in a comminution circuit. Modelling and simulation of blasting and comminution processes provide a more economic alternative to explore the impact of blast design changes on the down stream operations (Kanchibotla et al, 1998; Kojovic et al, 1998; Adam and Siddall, 1998; Bulow et al, 1998). However, the reliability of such simulations depends on:the ability of the models to reproduce the physical processes that take place; characterisation of rock mass in terms of its blastability and comminution characteristics; and in the case of blast modelling the ability to predict fines (-10 mm) has been found to be particularly important as this fraction has a significant effect on mill throughput.

Jan 1, 1999

The objective of this study was two-fold: 1. To perform a world literature search pertinent to the analysis, selection and design of hoisting systems and their components and to codify the search into a literature compendium. The search resulted in a technical data file of over 1500 hard copy items. The compendium index was also suitable for establishing a comprehensive computer-loaded data base on the subject. 2. To develop a comprehensive system of guidelines to cover salient aspects of analysis, selection and design of electrical, mechanical and structural components of a hoisting system with a view to establish parameters for maximum safety and efficiency of operation, installation and revision of the system. 3. Considerations in the mine shaft layout, design, sinking, outfitting, testing and commissioning are set forth against the background of requirements of applicable parts of Code of Federal Regulations, Title 30.

Jan 1, 1988

By H. Do, R. Yoon

Mineral flotation is effective over a relatively narrow particle size range of approximately 10 to 100 µm. If the upper particle size limit can be increased, however, a run-of-mine ore may be coarse ground, and only the middlings are ground further to achieve required grades. This will result in significant energy savings and increased throughput. In this communication, methods of increasing the upper particle size limit will be discussed on the basis of a flotation model that can predict flotation from both hydrodynamic and surface chemical parameters. An example of increasing flotation recovery by control of a chemistry parameter is given.

Jan 1, 2007

By Alan: Moore Richards

Effective control of airblast requires that significant factors be identified and satisfied by blast design and careful implementation. Significant factors include charge mass, distance, face height and orientation, burden, spacing, and initiation sequence, stemming height and type, topographical shielding, and meteorological conditions. This paper utilizes case histories of blasting in Australian open pit mines to demonstrate techniques that have been used to control airblast to applicable limits.

Jan 1, 2006

By H. E. Lee, D. Ingvoldstad

AT Bunker Hill the original charge storage and preparation system was installed in 1917 to accommodate lead-silver gravity mill products. Only minor tonnages of wet fines such as vanner and flotation concentrates were received. Charge flux and diluent requirements were provided by an ample supply of siderite middlings and coarse lime-rock. While oversize material was crushed through %-in., the use of roll crushers in series resulted in a more or less granular, free-running charge of adequate porosity. Under such conditions, receipts could be proportioned directly from receiving bins, and suitable blending was obtained by passing the resultant layered composite through a small Stedman disintegrator. This elementary system served well for production and smelting of an extremely lead-rich sinter, in the low column blast furnace. Here sinter physical quality is less critical, and appreciable quantities of raw flux and oxidized ore may be charged directly to the blast furnace without seriously impairing furnace capacity. Prior to 1938 the relative proportions of zinc receipts were low and extraneous flux requirements at a minimum. However, subsequent war-inflated zinc demands brought marked increase in fine concentrate and slimy zinc leach residue receipts and an abrupt introduction to smelting a more refractory zinciferous charge. The higher temperature demands of the more refractory zinciferous charge required a higher smelting column and the higher column, in turn, rendered the blast furnace less receptive to improperly prepared feed. Inadequate presinter processing facilities prevented the production of acceptable sinter, and blast furnace production declined to 50 pct of former capacity. In view of a prevailing contention among lead metallurgists as to the deleterious action of high zinc slag on blast furnace capacity, it was natural to overstress this factor and to concentrate on possible changes in furnace design. Another interpretation was that primary correction should be sought through expanded sintering facilities. This divergence of opinion, together with the extreme material shortages of the 1940's, delayed corrective

Jan 1, 1957

This publication summarizes, for potential contractors and other interested parties, the research, development, and demonstration contract projects programed by the Bureau of Mines for fiscal year 1979 (October 1, 1978-September 30, 1979) under its Mine Health and Safety Research program. The objective of these projects is to provide an ordered and sequenced series of advances toward the Bureau's overall goal of providing the system technology required to create a healthier and safer working environment for the Nation's miners.

Jan 1, 1979

By Daryl W. Wurster

The Liberty Bridge in Greenville, South Carolina is a curved, cable-stayed, pedestrian bridge with primary support provided by two towers. The bridge is part of the Falls Park redevelopment. The bridge was originally designed to be supported on drilled piers. Alternately, the bridge was supported on a combination of micropiles and anchor piles because of difficult access and subsurface conditions. The use of micropiles and anchor piles led to improved construction scheduling and reduced costs. Micropiles were used to resist compressive loads. Anchor piles were used to resist tensile forces and to eliminate excessive settlement of pile caps into underlying fill during pre-stressing. This paper describes the site history, bridge construction, site and subsurface conditions encountered, and the decisions that led to support of the bridge using micropiles and anchor piles and foundation construction.

Jan 1, 2006

By Christian Ottergren

"Modern crushers offer double the capacity and performance of classic models. In some cases crushers are replacing SAG circuits, the advantages being smaller investment and lower operating costs. Is Tertiary crushing replacing SAG milling as the most optimal grinding method? Does tertiary crushing achieve the same outcomes as SAG milling? This paper considers these questions and provides an assessment of the strengths of tertiary crushing in comparison to other methods. Two case studies: a Scandinavian Platinum Project, and CODELCO, are also presented.INTRODUCTIONResearch on basic parameters in crushing started at Chalmers University in 1993. The initial project has developed and now involves several related areas. Modelling in accordance with new theories has resulted in modified designs which have been implemented and shown improved performance at operating mines in Chile. Sandvik Rock Processing is a partner and a major supporter of this program. This paper will cover some of the achievements and give references to the research reports.The mining industry has for many years mainly used crushers of the traditional 7’crusher concept, with thread adjustment of the setting and with a spring or hydraulic overload system. This machine type has been the workhorse for crushing throughout the world. The explanation for the dominance of this machine is that it has a reliable mechanical design. It can be estimated that about 2000 crushers of this design are still at work.Technical development in all fields utilizes new technologies like high-strength materials, advanced control systems and more extensive use of hydraulics. This is the reason why today’s motorcars, for example, are more efficient, more reliable and more environmentally friendly than their predecessors in the 1950s. Crushers are no exception. This paper will cover experience from the latest-generation cone crushers developed by Sandvik Rock Processing.The parts in this paper related to the CODELCO ElTeniente copper mine in Chile are coauthored with responsible personnel from the operation at the mine."

Jan 1, 2004

By K. T. Lee, M. U. Ozbay, M. D. G. Salamon

Design of yielding chain pillars in deep coal longwall mines is not as well established due mainly to the lack of knowledge in the behavior of coal pillars in the post-peak regime. This study shows that two of the existing strain-softening models have the potential to provide an improved understanding of yielding and, therefore, could form a rational basis for yielding coal pillar design. Analytic and numerical modelings of a row of chain pillars in a two-entry development at a depth of nearly 700 m suggests that yielding pillars are feasible, but the design is very sensitive to the coal’s post-peak behavior.

Jan 1, 2001