Search Documents

Orebodies are defined in economic terms in that they must satisfy conditions determined by costs of mining, extraction and marketing before being so described. Despite this they have an essential chemical character as specialized products resulting from geochemical differentiation, and it is surprising that so little basic geochemical research has been carried out with respect to ore occurrence and that prospecting methods based on geochemical principles are not more widely applied.Many exploration geologists associate geochemistry with analytical techniques applied to the detection of dispersed traces of metals from actual orebodies. Geochemical research, applied to economic geology, goes far beyond this limited field and the purpose of this paper is to discuss aspects of such research and its use in formulating exploration principles.THE GEOCHEMICAL BACKGROUND TO MINERAL OCCURRENCE AND EXPLORATIONThe three aspects of economic mineral deposits to which geochemical research can be of use in determining ore guides are genesis, control of deposition and mode of dispersion from orebodies after emplacement. Prospecting for mineral deposits is primarily based on theories of ore occurrence which deal with the genetic and depositional influences controlling localization of ore. There are many such theories and they will not be discussed here as they have been adequately reviewed in geological publications. Some are based on differing argument concerning the same empirically observed associations of ore. In this respect it is perhaps fortunate that they are not always mutually exclusive as regards the...

Jan 1, 1960

By J Graaf, R A. Murrell

Gold Fields Australia is constructing two major ventilation shafts at the Wallaby gold mine in Western Australia. The new ventilation shafts are required to facilitate the long term ventilation strategy for the mine, thereby allowing continued extraction of ore beyond 1000 m below the surface. The construction work has involved all of the challenges that shaft construction can throw up, including challenging geotechnical conditions, unexpected high water inflows and major circulation loss during pilot hole drilling for raise boring. An extensive geotechnical and hydrological investigation program was undertaken prior to awarding the shaft construction contracts. While most of the risks were identified, several proved to be much more challenging than expected. The shaft construction methods included conventional sinking into the fresh rock profile in each shaft, followed by raise bore pilot hole drilling and reaming. A headframe was constructed for the first shaft, which was sunk to 92 m with a stage suspended in the shaft to facilitate the concrete lining and provide rope guides for the kibble winding. Drawing from experience when sinking the first shaft, additional ground pre-conditioning was implemented for the second shaft, which was pre-supported with continuous piles to 28 m followed by sinking to 50 m using a crane instead of winders and a headframe. Following the conventional sinking through the weathered zone in each shaft, the shafts were completed using a raise bore. The first shaft utilised a riser pipe and rotary vertical drilling system (RVDS) with the second shaft having utilised a dual rotary rig for pilot hole drilling. This paper reviews the site investigations undertaken, construction methodologies applied, the results achieved and the lessons learnt.CITATION:Murrell, R A and Graaf, J, 2017. Shaft construction at the Gold Fields Wallaby mine, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 321–334 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By Yoshinori Iwasaki, Shosei Serata, Yutaka Mochida

A new comprehensive insitu instrumentation technique named this RCC Method has been developed for rapid assessment and improvement of the structural stability of underground openings. When applied to tunnel construction, the degree of present and prospective safety of underground openings can be determined in quantitative terms within 10 to 20 minutes of microcreep observation. When applied to mining, roofs and floors can be stabilized by controlling the stress conditions. This stress control method has eliminated the need for intensive roof bolting and extensive floor renewal in all cases where it was applied. Use of this technique is illustrated by field examples from the Seikan Undersea Tunnel of Japan and deep potash mining in Canada. NEW INSTRUMENTATION TECHNIQUE: THE RCC METHOD Failure problems in underground excavation usually arise in weak non-elastic grounds where conventional rock mechanics theories of elasticity are not only useless but also misleading. Presently, discontinuity planes in the ground are being considered a factor in assessing these failure problems, and while this development is interesting academically, it is not of much use in actual excavation work, where it is nearly impossible to identify and quantize all existing planes of discontinuity. Even if such an extraordinary task could be accomplished at an underground excavation site, effective use of the data would be difficult and impractical for rapid excavation work, with the possible exception of rare cases of ideally elastic ground.

Jan 1, 1976

By Christopher J. Bise

INTRODUCTION The transportation of men, supplies, and mined material from an underground operation is the connecting link between the mine plant and the surface plant. Unless the mine is accessed by a drift or adit, some form of hoisting system is necessary for slopes or shafts. This chapter will deal with the selection of wire ropes and hoists, two of the most important consider¬ations when designing a hoisting system for an under¬ground mine. WIRE ROPES General A wire rope is designed to transmit forces longitudi¬nally along its axis. Wire rope is used in a variety of mining applications because of its flexibility, high ten¬sile strength, and dependability. Shaft hoisting ropes and principal slope haulage ropes are usually custom-¬built; however, proper rope selection for slushers, car spotters, etc. should not be overlooked. Wire ropes for shafts and slopes, since they represent the life line for the mines, should be of the very highest quality improved plow steel. This quality is necessary to deal with the conditions of loading, winding, vibration, abrasion, and corrosion. Tables I and 2 display the specifications for the typical wire ropes used for mine haulage applications. The 6 x 19-class haulage rope is used for most hoisting where abrasion is not critical. On the other hand, where abrasion is critical, such as a slope application, 6 X 7-class haulage ropes are preferred. For other mining applications, manufactur¬ers' handbooks should be consulted. Selection The selection of a wire rope for a mining situation consists of simply applying appropriate safety factors to a calculated maximum rope pull and comparing the result to the listed breaking strength of the rope under consideration. Table 3 can be used for determin¬ing the minimum factors of safety for wire ropes. To determine the maximum rope pull, the following quantities must be known: the rope weight in pounds (x), the conveyance weight in pounds (y), and the weight in pounds of the load in the conveyance (z). These values are used to calculate the load due to gravity, the load due to conveyance friction, and the load due to rope friction. When these loads are added together, as shown in Eq. 1, the maximum (static) rope pull (RPS) can be derived:

Jan 1, 1986

Comparison of Grinding and Liberation Processes for Stalky Biomass Materials as a Prerequisite for Production of Energy Pellets with High Calorific Value Pelletising biomass, especially straw and stalky materials, requires a product specific size reduction and liberation. However, moisture content plays an important role in palletising and also affects the energetic properties of the biomass. The paper illustrates the characteristics of the mentioned type of biomass and specifies the necessities for production of energy pellets. Defined requirements for biomass energy pellets will be shown based on relevant standards. The work focuses on a comparative investigation of the straw fibres after grinding with hammer/impact mill and after the liberation of the straw fibres with twin-screw extruder (two different communition units). A traditional hammer mill as well as an hydrothermal process taking place in a twin-screw extruder were utilised. Results of the grinding and liberation of rye and wheat straw fibres are discussed based on a detailed particle characterisation (particle size and shape distribution). Besides high calorific value the main pellet quality parameters are mechanical stability, abrasion resistance and further combustion technical characteristics. The particle size distribution displayed optimum characteristics for the combustion processes to be carried out in a furnace. The durability of the pellets produced from straw fibres liberated with twin-screw extruder was comparatively better then that prepared with the straw fibres after grinding with impact mill. Particle size distribution, abrasion values and the strength characteristics showed a good correlation with each. The high presence of N and S would result in high NOx and SOx emissions, where as the high concentrations of Cl would corrode the furnace. These chemical properties of the straw would restrict its usage in small scale furnaces.

Sep 13, 2010

In the course of the last twenty eight years the copper lodes of New Caledonia have been periodically worked or abandoned, until quite recently, probably attracted by the higher price of the metal, British capital has again been induced to embark upon the further development of several copper properties, which at present give reasonable promise of becoming regular producers. Owing to its proximity to Australia (only a three day's journey by mail steamer from Sydney) New Caledonia becomes of additional interest to Australian commerce in general, and it is to be hoped that the French Government may see their way before long to make the best of this natural position, to the mutual benefit of both countries concerned.Op till now all copper ores and concentrates which have been shipped from New Caledonia, were treated in Australian smelting works furthermore, Australian mine managers and miners have from time to time been connected with New Caledonian mining ventures, but, unfortunately, it must be said that nearly everyone of them returned to Australia thoroughly disgusted with his experience over there. Even to the casual observer, it is not so very difficult to find a proper explanation for these shortcomings in the peculiar economic conditions of the 'French colony, as many of the objections which have hitherto existed in connection with mining operations, were the direct consequences of a system of colonisation which could not possibly have been productive of better results.

Jan 1, 1901

By J. T. Popp

This Bureau of Mines study reviews the geological factors that affect methane in the Beckley coalbed in southern West Virginia, including overburden, coalbed structure, type of and changes in lithology above and below the Beckley coalbed, and presence of fractures in the coal and rock adjacent to the Beckley. Depending on the depth, the Beckley coalbed emits from 216 to 520 ft3 of methane per ton of coal mined, and the Bureau estimates that methane emission in a deep, extensively developed mine in this area may exceed 3,000 ft3 per day per ton of coal mined. Average face cleat and butt cleat trends in the Beckley coalbed measured underground are N 33° W and N 53° E, respectively. Close cleat spacing con¬tributes to the friable nature of the Beckley and provides easy movement for methane and water. Because rider coals, splits, and carbonaceous shales may contribute methane to mine emissions, predictions of methane emission based on gas content of the Beckley coalbed alone may be conservative. Beckley coalbed reserves in the study area are 234 million tons. The gas content of the Beckley coalbed averages 407 ft3/ton, and the coalbed gas reserves are 108 billion ft3.

Jan 1, 1976

By Mark Fernald, Christian O’Keefe, John Viega

"In this presentation, the SONARtrac™ technology platform will be described. CiDRA's proprietary clamp-on, passive sonar array-based flow meter technology performs two independent measurements – flow rate and fluid characterization. Firstly, the meter provides the volumetric flow rate of the mixture by measuring the speed at which naturally occurring turbulent structures convect with the flow past an axial array of sensors. Secondly, the meter uses similar sonar-based processing techniques and naturally occurring sound in the process fluid to measure entrained air levels. The result is a unique ability to measure the flow rate and entrained air level of most fluids – clean liquids, high solids content slurries, and liquids and slurries with entrained air.Also to be presented is the application of the sonar-based technology platform in a variety of oil sands processes, hydrotransport, and minerals beneficiation applications. In particular, difficult slurry flow measurement and control in the areas of comminution and flotation such as mill discharge, hydrocyclone feed/overflow, final concentrate, thickener discharge, and tailings will be discussed. In addition new real time maintenance free process measurement capability will be presented in the areas of entrained air in slurry, collection zone gas holdup (?g), and slurry velocity profiling. The operational advantages and value of these measurements, even in the presence of scale buildup, will be discussed.INTRODUCTIONFlow measurements in the mineral processing and oil sands industry suffer from the limitations placed by previously available flowmeters including the commonly used instruments such as ultrasonic meters, magmeters, turbine meters, orifice plate meters, vortex flow meters, Coriolis flow meters, and venturi meters. The desire or requirement to make a non-contact measurement that is accurate and robust, and can be performed on practically any type of fluid within practically any type of pipe has driven the creation of a new class of flowmeters. This new class of flowmeter technology utilizes sonar-based processing algorithms and an array of passive sensors to measure not only flow, but also fluid composition."

Jan 1, 2007

Structurally- controlled deep leaching processes have removed vast quantities of carbonate from a substantial portion of the "silica-dolomite" enclosing the 500 copper orebody. Mine drainage subsequently allowed free access of air to the porous environment created and oxidation of sulphides commenced. During the mIne development stage the exothermic and temperature-dependent nature of these hydrolysis reactions resulted in a slow general elevation of ground temperatures. and levels of 90 - lOO°C were attained in restricted moist sulphide-rich areas.With the advent of production and extensive use of explosives, the oxidation processes were locally raised to new levels of activity. Direct interaction of explosives and sulphides in favourable conditions caused temperature rises to above 260 C. Above this point the dry oxidation of sulphides in air was initiated and rapid escalation to the vicinity of 800 C has been known to occur in isolated cases.Ground reactivity is a function of the complex interrelationship of several controlling factors and no simple index exists.Control techniques are presently aimed at prevention of temperature rises in the range 100 -260 C. Inhibition of the rapid dry oxidation processes above 260 C is difllcult and current efforts have met with only partial success.

Jan 1, 1968

The Mineral Sector Development Project, sponsored by the World Bank, has been set up to revise the legal, regulatory and fiscal framework for the minerals industry in Tanzania, with a view to attracting mining companies and investors to the country and facilitating future minerals development. One component of this project, the Environmental Management Framework for the Mineral Sector, was awarded to Wardell Armstrong of the UK and ENV Consult of Tanzania. In developing a new framework of environmental regulations, emphasis was placed on developing realistic standards which reflect local conditions and prevailing values. The main corner-stones of this approach are; effective environmental impact assessment procedures; establishment of environmental management procedures; and monitoring and auditing of companies? performance. The favoured approach involves a three-tier framework, as follows: ?Framework environmental provisions within the new Mining Act; ?Regulations covering more detailed environmental requirements ?Guidelines and/or Codes of Practice, which may in future become regulations in their own right. Careful consideration has been given, in developing the framework, to the limited resources likely to be available for implementation to the Ministry of Energy and Minerals and this has influenced the approach that has been adopted. This paper outlines the main components of the environmental management framework and discusses some of the important issues raised by these proposals.

Jan 1, 1998

By J. J. Wallace

This report describes the initial phase of Bureau of Mines research in the hydraulic mining of bituminous coal. The mining site and equipment are described, and the test procedures and results obtained with a bar-mounted monitor are given. Tests showed that hard Pittsburgh-bed coal can be mined hydraulically from a solid face at water pressures of 4,000 pounds per square inch.4 Coal was penetrated to a depth of 4 feet in 20 seconds with 225 gallons of water per minute coming from a 3/8-inch nozzle at 4,000 pounds per square inch pressure. Some difficulty was encountered in cutting the binders occurring in the coal; it was not possible Lu penetrate directly the overlying draw slate.

Jan 1, 1961

By J. C. Martin

Equations for three-phase, three-dimensional, compressible flow (including capillarity) are reduced to two-dimensional relations by a partial integration. This reduction allows three-dimensional flow problems to be treated with mathematics for only two spatial dimensions. The results can be used to formulate flow equations for two-dimensional reservoir simulators in which the effects of capillarity and fluid segregation in the third dimension are represented. Such reservoir simulators would retain many of the aduantages of two-dimensional simulators while simulating three-dimensional effects. The principal restriction of the method is that the thickness of the reservoir should be small, compared to the distance across the reservoir. INTRODUCTION In recent years, computers have been used to calculate the performances of many reservoirs. Most of the detailed calculations, however, are based on finite difference solutions of the flow equations, and present day computers are seldom able to handle a sufficient number of cells to produce entirely satisfactory solutions, even for reservoirs represented by two-dimensional arrays of cells. The situation becomes much worse when one wishes to approximate the reservoir by a three-dimensional array. A great saving in computation or a more detailed solution can be obtained for many reservoirs by using the partial integration of the equations of flow presented in this paper. The integration reduces the three-dimensional equations to two-dimensional relations; and, for studies of two-dimensional flows in vertical cross-sections, the equations are reduced to one-dimensional relations. Most reservoir performance calculations currently are based on one- or two-dimensional flow re1ations.l-3 In some cases flow in the third dimension is approximated by assuming a particular type of vertical saturation distribution, such as gravity segregation.l.2. The relations developed in this paper approach those for segregated flow as the capillary pressures approach zero, and they approach those for uniformly distributed saturations as the capillary pressures are increased. For this analysis, the ratio of the reservoir's thickness to the maximum distance across it must be small. The capillary pressures between the oil and water should also be small compared to the maximum pressure difference in the reservoir. This requirement is met by most reservoirs. It is assumed that the capillary-pressure curves are well defined, whether or not hysteresis effects are included. Also, the reservoir must have sufficient vertical permeability to allow the fluids to segregate. The results presented here provide a firm theoretical foundation to Coats' et aL5 assumption of vertical equilibrium and extend the relations to three-phase flow. Coats' assumption of vertical equilibrium, which he verified by calculations and experiment, is developed here mathematically from basic flow equations. DISCUSSION SATURATION AND PRESSURE DISTRIBUTIONS Appendix A presents a mathematical analysis of fluid flow in reservoirs where the ratio of thickness to maximum distance across the reservoir is small. The results indicate: (1) that the fluids along any line perpendicular to such a reservoir's upper surface are in static capillary equilibrium (vertical equilibrium); (2) that, to a first approximation, the fluid pressures and properties are functions of only areal position in the reservoir and time; and (3) that hydrostatic pressure gradients exist along any line perpendicular to the reservoir's upper surface. The results might be expected after studying several physical considerations. First, no flow is allowed normal to the upper and lower reservoir boundaries, which are relatively close together.

Jan 1, 1969

By H. Boghosian

This paper presents the design and construction of a deep basement in a steeply sloping site in glacial till in Glasgow city centre. Existing foundations, adjacent structures and services, in tandem with asymmetric loading, presented particular challenges in the planning, execution and design of the project. The construction methods and temporary works, analysis by the Finite Element method and monitoring carried out are all described.

Jan 1, 2006

By Dennis P. Martin, Michael M. Fitz, James E. Friant

Methods for reducing the cyclic nature of drill and blast tunneling operations have been long needed. A miniature blasting system using 10 mm (.375 in.) holes, 0.91 m (36 in.) deep, and blasting only one hole at a time makes it practical for men to work behind a shield, remaining at the face during the entire process. A prototype automated module was developed to drill, load the hole and initiate the detonation without moving from the hole. A unique cost effective gell explosive and a novel, low cost initiation method were developed.

Jan 1, 1989

By Fredrick Fränding

In mining and quarrying operations, electric motors can fail for a variety of reasons. Some failures are directly linked to demanding production requirements and contaminant-laden environments and, consequently, are difficult to prevent. A sizeable number, however, are caused by ?offline? factors that have nothing to do with production. These include inadequate or substandard motor repair practices and improper motor shipping, storage and installation. The fact that failures are at times attributable to repair- or rebuild-related errors and problems raises the stakes when selecting an electric motor repair provider. Teaming with high-quality electric motor shops can help a company reduce failures due to offline factors, improving motor reliability and cutting downtime costs. Regardless of location or annual revenues, the best motor shops have similar business cultures and share many of the same characteristics.

Jan 1, 2009

Some 800 analyses for Cu, Zn, Pb, Ag, Fe, S, CaO, MgO, C02, Si02 and Al203 were used to examine the elemental constitution of the Mount Isa ores, and, for comparison, those of the Northern Leases area.Lead: zinc relations show little order from sample to sample, but means of large zones (Le. individual orebodies) show a highly linear inverse relationship. Lead: silver ratios are fairly constant from sample to sample, and means show a highly linear direct relationship.Sulphide sulphur appears to be related to carbonate and alumina abundance, sulphur decreasing systematically with increase in the ratio CO2:AI203. In all graphs involving members of the group CO2-A203-S the lead-zinc and copper ores conform to the same simple trends, confirming that the two ore types and their host rocks are genetically closely related. The earlier deduction of a volcanic-sedimentary origin for the sulphides of the Black Star orebodies appears compatible with present findings.On the basis of such an origin, the pattern of sulphide occurrence and mineralogy in the Mount Isa district is possibly related to the configuration f the upper surface of the "Eastern Creek Volcanics", the facies patterns of the overlying sedimentary rocks, and to the oldest faults affecting the two.INTRODUCTIONStanton (1962) described and interpreted the chemical constitution of the Black Star No. 2 lead-zinc and the 650750 copper orebodies at Mount Isa. The investigation has now been extended to the other principal orebodies of the area.The earlier study showed that the host rocks of the two adjacent Black Star orebodies were constitutionally closely related, and suggested that this was probably due to their original formation in contiguous zones of sedimentation. On this basis the silica-dolomite of the copper ore appeared to represent the slightly more shoreward, "limey" member, probably a fairly massive algal calcareous sediment laid...

Jan 1, 1963

By James D. Noll, Jon A. Hummer, Shawn E. Vanderslice, Aleksandar D. Bugarski, George H. Jr. Schnakenberg, Steven E. Mischler, Larry D. Patts

The National Institute for Occupational Safety and Health designed and conducted a study in an underground metal mine to assess the effects of selected diesel emissions control technologies on the concentrations of diesel particulate matter and gases in underground mine air. The control technologies studied included diesel particulate filter (DPF) systems, filtration system with disposable filter elements, diesel oxidation catalytic converter, and biodiesel blends. Each technology was tested on a mining vehicle operated in an isolated area of an underground mine supplied with fresh air. These isolated zone tests allowed for the operation of vehicles under conditions and over duty cycles that closely mimic actual duty cycles of production equipment. The DPF systems reduced the elemental carbon (EC) concentrations in mine air between 88% and 99%. The same systems reduced total particulate matter (TPM) concentrations in mine air by approximately 75%. The biodiesel blends B20 and B50 caused a reduction in the EC concentrations of 26% and 48%, respectively. Those blends also reduced TPM concentrations by 9% and 24%, respectively. The use of #1 diesel fuel reduced EC concentration by 13% compared to #2 diesel fuel. An increase in nitrogen dioxide concentration of up to two times was seen when platinum-catalyzed DPF systems were tested.

Jan 5, 2006

By F. Russo-Bello

TauTona Mine (the renamed Western Deep Levels East) is using a longwall mining method with stability pillars to extract the Carbon Leader Reef at a depth ranging from 2097 metres to 3456 metres below surface. Seismic activity and the complexity and hazards associated with negotiating geological features at great depth pose the most severe hazard to deep level gold mining in South Africa. It impacts negatively on safety and the profitability of the mining. The critical success factors in longwalling at depth are: ?Sound mining strategies and face shape control ?Ensuring follow behind development infrastructure is kept up to date ?Support system design as a strategy to effectively limit the serious effects of damaging seismicity. This paper describes the following: ?Implementation of the required mining strategies ?The evolution of a new stope support system and problems associated with its development and implementation. How this support system was adapted for the successful negotiation of major geological features with known seismic potential and problems encountered ?Current initiatives to optimize follow behind development infrastructure ?Current initiatives in designing a new gully support system and problems experienced with its development and implementation. Finally, this paper will deal with the way forward, briefly covering areas like the above-mentioned gully support system, the proposed phased introduction of technology, and the use of alternative mining layouts.

Jan 1, 2000

By K. Lombard

"‘Roof support awaiting time’ (RSAT) is a term used at Goedehoop Colliery’s Simunye Shaft to describe the potential production time lost due to the continuous miner (CM) standing idle waiting for roof support to catch up. Investigations revealed that in 2013, Simunye Shaft had approximately1400 hours of RSAT, which suggests that the mine could have potentially produced an additional 280 000 t of coal. This project consisted of two parts. Firstly, the causes of the high RSAT and means to improve the situation were investigated. Secondly, as insisted by mine management, the CM cutting sequence was investigated as a possible cause of high RSAT. Machine-related challenges due to the roofbolter installing support too slowly, geological conditions (mostly hard roof conditions and slips),logistical challenges pertaining to the CM cutting sequence, man-related challenges related to operator fatigue, re-support, operator inexperience, and the absence of support targets were identified as main contributors to RSAT. Furthermore, results showed that the roofbolters in the sections at Simunye Shaft are slower than the CMs. A target of 28% reduction in RSAT was set. Experts from Kennametal and Fletcher were consulted to find solutions for the identified causes. In total, eight solutions for RSAT were identified, but the solution that contributed most significantly to reducing RSAT was to use hard roof drill bits as a standard product at Simunye Shaft. Calculations showed that by using hard roof drill bits, RSAT can be reduced by 43%, which is more than the specified 28% target. The cutting sequences at Kriel, Greenside, and Simunye Shaft, togetherwith three newly developed cutting sequences, were simulated using the UCMS (Underground Coal Mining Simulation) program. A re-aligningprinciple was incorporated into the newly developed cutting sequences toalign the cutting sequences to general support work and to reduce RSAT. A decision matrix revealed that a cutting sequence in which boxing takesplace in R3 (third road to the right of the belt road) and in which the re-aligning principle has been incorporated will be the best option for Simunye Shaft. The recommended cutting sequence will lead to a 5% increase in production.The work presented in this paper was carried out as partial fullfilment for the degree BEng (Mining Engineering)"

Jan 1, 2015

By L. W. Pommier, F. B. Brien, A. K. Bhasin

In the field of mineral processing, although many operations are applied to suspensions of ore particles in fluids, there is a lack of fundamental knowledge relative to the flow resistance encountered by immersed bodies moving through solid-liquid suspensions. Previously proposed equations, based on the Ostwald-de Waele (power-law) model for non-Newtonian fluids, are exam ined in the turbulent flow region relative to a number of pertinent variables and their effects on the movement of immersed bodies. As more knowledge is acquired in regard to the effects of suspension variables on the rheological properties, useful relationships may be proposed to allow predictions of conditions to achieve optimum results for engineering purposes. In the field of minerals processing, many operations are applied to suspensions of ore particles in fluids. The differential movement of solids of various sizes and densities in suspensions is of utmost importance to gravity concentration, wet classification, flotation, hydrometallurgy, and pipeline transport of solids. The subject is also of importance to other branches of engineering; for example, those involved with soil mechanics, ceramic slips, and oil-well drilling fluids. There is a lack of fundamental knowledge relative to the flow resistance encountered by immersed bodies moving through solid-liquid suspensions. The problems encountered in the direct application of the well-known Stokes and Newton's Laws to non-Newtonian systems have been examined in a previous paper.' Equations were proposed based on the Ostwald-de Waele (power-law) model for non-Newtonian fluids. This present paper examines these equations in the turbulent flow region relative to a number of pertinent variables and their effects on the movement of immersed bodies. It is thought that, as more knowledge is acquired as to the effects of suspension variables on the rheological properties, useful relationships may be proposed to allow prediction of conditions to achieve optimum results for engineering purposes. The purpose of this paper is to make an initial assessment of the nature and magnitude of pertinent suspension variables. In order to avoid too voluminous a document, the examination of kinetics and mechanisms will be omitted at this time. THEORY A Newtonian fluid is defined as a fluid in which the stress is proportional to the rate of strain, 2 i.e.: H = viscosity; see Table I. for list of symbols The following equations are conventionally used to assess the motion of spherical particles moving under laminar and turbulent flow conditions through Newtonian fluids: When these relationships are applied in practice to suspensions, the liquid density is substituted by a composite suspension density, and viscosity is usually taken as that of the suspending liquid or an approximated "apparent viscosity." However, suspensions are non-Newtonian in character3 and thus, more than one viscosity parameter is required to describe their behavior. A number of models have been proposed for non-Newtonian fluids;2,4 among these the simplest is the Ostwaldde Waele or power-law model for incompressible fluids which for one dimensional flow may be reduced to:

Jan 1, 1970