Search Documents

Flotation of Phosphate Gangue from Magnetite Fines - Non-Ionic Surfactant as Atrac Collector Modifier

Sep 13, 2010

By M. J. Lukhele

Paper written on project work carried out in partial fulfilment of B. Tech (Mining Engineering) degree A number of high wall mining methods were developed over the years to mine coal reserves exposed on the high walls created during surface mining. The auger mining system was initially developed in the early 1940s in the United States of America. High wall mining is a method of recovering coal from seam exposed either by mechanical excavation methods or natural erosions. This is usually associated with strip-mining (opencast) where the stripping ratio is high and uneconomical to mine using the opencast mining method. This paper discusses the surface auger mining as deployed at Rietspruit Mine Services Proprietary Limited.

Jan 1, 2002

By J. O. Marsden

Part I in this series of papers considered the chemistry of medium-temperature pressure leaching of copper sulfide concentrates and reviewed the metallurgical testing and initial process development for this technology. This initial work resulted in the development of a process flowsheet utilizing superfine grinding (to a P98 of 12 to 15 µm and P80 of 6 to 7 µm), pressure leaching at 160° to 170ºC, followed by conventional solution extraction (SX) and electrowinning (EW) for the recovery of copper. However, this process required a significant amount of concentrated acid to be fed to the pressure leach vessel to meet the reaction requirements, representing a cost of between $0.03 and 0.05/lb copper (2006 basis) produced by the process. It was immediately recognized that the development of a process that did not require such a large acid addition would be advantageous. This paper, which is Part II in the series, describes the development of a process that incorporates medium-temperature pressure leaching and direct electrowinning (DEW) in a novel and innovative process flowsheet. Phelps Dodge (a subsidiary of Freeport-McMoRan Copper & Gold Inc.) refers to this as the ?MT-DEW-SX? process. Part III in this series covers the large-scale demonstration of the MT-DEW-SX process at Bagdad, Arizona; and Part IV addresses the development and design of a full-scale commercial application at Morenci, Arizona.

Jan 1, 2007

By H. H. Schrenk, W. P. Yant, F. A. Patty

"INTRODUCTION In accordance with the outline of investigation described in a previous report 5 of the Bureau of Mines dealing with the use of acrolein for detecting leakage of methyl chloride from unit--type refrigerating systems, the work has been extended to include an investigation of its use in a multiple system, This report gives the results of analysis of samples of the gas from representative units of a multiple system charged with methyl chloride containing approximately 0.9 per cent acrolein by volume, The results furnish a basis for estimating the Warning that would be given in event of leakage. The properties and warning intensity of acrolein have been described in a previous report. 5 ACKNOWLEDGMENTSThis investigation was made at the combined request-of Several Inc., Manufacturers of refrigerating, appliances, and the Roeasler Hasslacher Chemical Co., manufacturers of methyl chloride. Acknowledgment is given to R. M. Major, ,chief chemist of the former firm for arranging the experimental site and equipment; to Arthur O. Haseeneall, owner of the apartment building where the investigation was conducted, for his courtesy in permitting the investigation; and to R. R. Sayers, chief surgeon, Bureau of Mines, and surgeon., U. S. Public Health Service, for suggestions and advice."

Sep 1, 1930

"This paper describes some of the methods and equipment used for fine milling of minerals, and gives particular attention to the Vibro Energy system.In addition, the paper describes a specific application in the gold mining industry. This is the 200 tpd plant built by Anglo American Corporation at the President Brand Mine in South Africa in 1985, now a division of Freegold. This plant treats a gold bearing pyrite flotation concentrate which is finely ground to 15 microns prior to cyanidation and carbon-in-pulp (CIP). l .0 INTRODUCTIONFree milling gold ores are those that yield acceptable dissolution and recovery of the gold following grinding to what can be described as normal fineness, frequently between 50% and 90% passing 74 microns.Increasingly, gold metallurgists are faced with ores that are refractory. The traditiona1 treatment route for refractory gal d ores and concentrates has been by roasting, but for environmental reasons this is becoming less acceptable, or in some areas of the world, totally unacceptable. New methods of treating refractory gold ores are being developed and applied in practice. These new methods include pressure and biological oxidation. Higher gold liberation can also be attained by increasing the fineness of grind, although with conventional systems there are economic limits to this.In flowsheet development and test programs on new deposits, a standard procedure is to establish the relationship between the grind and subsequent go 1 d extraction. The normal situation is that gold extraction increases as the ore, or concentrate, is ground finer. Typically, this relationship is as shown in Fig. l, where the incremental additional extraction is very small once an optimum, or economic, grind has been achieved. This generally app1ies whether the material is free milling or refractory. The limits to grinding are set by the type of equipment which is commonly in use, usually ball mills. These mills have the obvious advantage of high capacity, however, they are increasingly inefficient as finer grinds are required. In general, ball mills are used to reduce ore to some agreed percentage passing 74, or possibly 53 microns."

Jan 1, 1988

By M. K. Pelser

The purpose of this paper is not so much to provide a scientific study of the selection process for the perusal of other psychometrists or industrial psychologists?the purpose is to provide line management with a practical, relatively user-friendly guide to fair and scientific selection. The main areas that are to be covered are: ? Why fair and scientific selection? ? Job analysis ? The job requirement?selection technique circle ? Assessment centres in the mining industry?the Tavistock Collieries Ltd experience. Why fair and scientific selection? Seen from a line manager?s perspective, fair and scientific selection should be pursued for two main reasons: ? to remain within the ambits of the law ? to maximize the probability of selecting the potentially most productive and efficient candidate for the job.

Jan 1, 1997

By P. Roy

Smelting or converting of sulphide concentrates and mattes in a batch operation presents a challenge when directing the off- gas to a conventional acid plant. The Hindustan Zinc Ltd. (a division of the Vedanta Group of companies) Chanderia Lead Zinc smelter was presented with such a challenge that was met with the adoption of the Cansolv® SO2 Scrubbing System. The Ausmelt top submerged lance technology used at Hindustan Zinc generates a furnace gas stream that contains between 0.1 vol% and 12 vol% SO2 during the three stages of batch smelting. Cansolv® SO2 Scrubbing Technology captures the SO2 to ensure that treated flue gas exits the facility at a concentration below 100 ppmv SO2 and it releases SO2 in a controlled fashion, to more closely match the needs of the existing acid plant. The application of a regenerable scrubbing system to capture SO2 from a batch-operated furnace and convert it to acid in a conventional acid plant was a first of its kind in the world. This paper provides an update on the design and operation of the Hindustan Zinc SO2 recovery system and suggests two improvements to the basic flow sheet that optimize the cost of SO2 scrubbing further.

Jan 1, 2007

By Eric Konigsmann, Doug Spence, Scott Jones

"The Williams Gold Mine is located in the Hemlo camp of Northwestern Ontario and is one of Canada’s largest gold producers with annual gold production of 400,000 ounces. The operation is owned and operated as a 50:50 joint venture between Teck Cominco Limited and Barrick Gold Corporation.In July 2002, the decision was made to introduce paste backfill produced from mill tailings as the primary backfilling method in the mine and to decommission the existing cemented rock fill system. This required a fast track design to be completed for both a surface paste backfill plant and an underground paste distribution system followed by an intensive construction phase through the fall and winter of 2002/2003. The paste system was commissioned on schedule in late April 2003 and was in full production within 4 weeks of the initial start up. Overall, the project duration was only 42 weeks from initial project release to commissioning and it was completed $2 million under the budget of $14 million.This paper presents an overview of the lab testwork and process flowsheet design, process control methodology and describes the construction and commissioning phases of the project. Preliminary paste plant performance and operating cost data is also presented.IntroductionThe Williams Gold Mine is located in Northwestern Ontario adjacent to the Trans Canada Highway in the Hemlo Gold Camp as shown in figure 1. The mine currently produces approximately 400,000 ounces of gold annually and is owned and operated as a 50:50 joint venture between Teck Cominco and Barrick.The deposit was discovered as part of the Hemlo gold discovery in 1981 which led to the development of three mining operations within a 2 kilometre radius. The neighboring operations are the Golden Giant Mine, currently owned and operated by Newmont Gold, and the David Bell Mine, currently owned and operated by the same joint venture which is running Williams. David Bell ore is blended and milled in the Williams concentrator."

Jan 1, 2004

By Jewel A. G. Gomes

Green rust (GR) are layered Fe(II)-Fe(III) double hydroxides, having a pyroaurite-type structure consisting of positively charged hydroxide layers and hydrated ions in interlayers. This special feature of GR is very efficient for wastewater treatment as the pollutants are easily taken in or exchanged with the anions in the interlayers. It can be simply and cost-effectively produced by electrocoagulation (EC). Chicken processing plant (CPP) produces large amount of wastewater containing variety of readily biodegradable organic compounds, fats, and proteins. The possible re-use of properly treated CPP wastewater would be economic and environment friendly. In this study, we present our work on treatment of CPP wastewater using EC, specifically for the removal of COD. Analysis of the EC-treated water for reuse in the same plant is discussed considering the U.S.EPA regulations. Two types of EC-reactors were used for this purpose. To better understand the treatment mechanism, EC-floc was also characterized using XRD and SEM-EDS.

Jan 1, 2010

By Jim Baumann

Deposited millions of years ago in irregular paleokarstic channels, Jamaica’s extensive bauxite deposits provide good quality ore for alumina production and subsequent aluminum smelting. Bauxite mining operations are critical to the Jamaican economy. It accounts for a large percentage of Jamaica’s export earnings. Bauxite production in Jamaica accounts for about 10% of the world’s output each year. Bauxite deposits in Jamaica lie close to the surface. They can be extracted using standard surface mining techniques. The deposits occur in scattered pockets across the country’s rugged landscape. So it was necessary for two of the country’s major mining and refining operations to implement cost effective methods for the acquisition and management of bauxite reserves and surface ownership distribution rights.

Jan 1, 2002

By N. Andersen

During the preliminary design phases and feasibility study of a proposed vertical shaft, a vertical diamond drill-hole is normally drilled on the site. This paper outlines how rock mass characteristics, in-situ rock stress, rock strength, hydrological characteristics, and structural parameters can be determined using wireline logging of this borehole. In addition, a rock mass classification scheme is developed, based on published work, and in particular the Q-factor is adapted to assess the stability of raise-bored shafts. The ‘stick plot’ is introduced, which combines all geotechnical parameters applicable to the stability of a vertical shaft into a colourcoded format where cross-correlations can readily be made on a day-today basis during the shaft-sinking process.

Jan 1, 2015

By Verya Nasri

The proposed Second Avenue Subway Project in New York City is approximately 8.5 miles long, up to a depth of 120 feet beneath grade and runs the length of the eastern side of the island of Manhattan from Harlem in the north to the financial district in the south. It will reduce overcrowding and delays on the existing parallel line, improving travel for both city and suburban commuters, and upgrading access to mass transit for residents of the East Side of Manhattan. This subway line will have 16 new stations providing transfers to the existing Metro-North commuter rail service and to New York City Transit subway lines and bus services. The first phase of construction includes two TBM rock tunnels 2.4 miles long and two new large and shallow rock cavern stations with clear span openings ranging from 70 to 100 feet and length in excess of 1000 feet with 615 feet center platform, coupled with low rock cover ranging from 20 feet to 40 feet. The design methodology for these large and shallow rock caverns consists of using well known empirical methods for initial estimate of support requirements and then two and three dimensional continuum and discontinuum analyses for verification of the selected excavation sequence and support system. This paper describes the analysis and design methodologies used for the two large and shallow rock caverns with insight into how to overcome the design complexities and construction challenges of the urban underground.

Jan 1, 2008

By Pr-Anders Persson

This chapter deals with the concepts of shock waves and detonation waves together, because a detonation wave is really a shock wave, supported by the explosive reaction that the shock wave ignites and propagates as it travels through the explosive material. In the c.ootext of rock blasting, furthermore, there is justification for treating shock waves and detonation waves together, because the mechanical effect of the detonation in an explosive in a drillhole in rock is propagated and its effects are spread throughout the surrounding rock by means of a shock wave. The overall performance of sn explosive in rock blasting or any other application is of course dependent on how much thermal energy is released in the chemical reaction that occurs when the material detonates, and on how much useful mechanical work the reaction products can do as they expand. A major portion of this chapter deals with the prediction and measurement of explosive performance, a subject which is now still in a process of rapid development.

Jan 1, 1995

By Hennessy F. L

IntroductionEvolution of the Present SmelterRoastingFiringHearth SlopeDust HandlingFurnace DetailsSmeltingFurnaceFeed DeliveryPulverised Coal FiringWaste Heat BoilersDust HandlingAir PreheaterReverberatory Slag DisposalConvertingVesselsAir SupplyMatte TappingConverter Slag HandlingPurchased Ore PlantINTRODUCTIONSmelting in blast furnaces commenced at Mount Morgan in 1906, when copper, which interfered with gold recovery by chlorination, became an asset. After various changes in blast furnace practice, reverberatory smelting com...

Jan 1, 1952

By Valentín Pamo

El presente trabajo describe los procesos y equipos que permiten la extracción de metales preciosos de la refinería de Ilo en condiciones agresivas, obligando a investigar materiales resistentes a la corrosión. Asimismo, se presentan alternativas que aseguren la continuidad de las operaciones en el proceso productivo de dicha refinería.

Sep 9, 2007

This paper deals with the application of table flotation to two unusual mineral dressing problems. Both problems involved the removal of interfering minerals at sizes too coarse to normal froth flotation.The first problem was the removal of arsenical minerals from Broken Hill gravity concentrates without further size reduction. Table flotation without grinding of the original concentrates gave almost complete rejection of the arsenic from the concentrates. A typical test result was a reduction of arsenic in jig concentrate from 0.75% arsenic to 0.007% arsenic.The second problem was to develop a method to produce a high grade calcium carbonate concentrate from coastal dune sands containing about 10% silica and about 80% calcium carbonate. The sands were about 30 mesh British Standard Screen (B.S.S.), and for economic and other reasons it was stipulated that the separation be made without grinding. Again, table flotation gave excellent results. A concentrate was produced containing 99.62% acid soluble material, representing a recovery of 98.69% of the calcium carbonate in the feed with a rejection of 96.44% of the silica.The investigations' were carried out at the Kalgoorlie Metallurgical Laboratory, under the Department of Mines...

Jan 1, 1954

By J. B. Zadra

Tungsten metal, chemically equivalent to commercial grade, is produced by electrolysis of impure tungsten compounds or scheelite in an alkali, phosphate or borate electrolyte. A preliminary investigation of fused-bath electrolysis shows the effect of electrolyte composition, temperature, and current density on current efficiency, yield, crystal structure, and purity of product. Experiments show that tungsten can be electrowon from scheelite in a fused alkali, phosphate, or borate bath with similar results. Studies on electrolyte composition show that the addition of sodium chloride is essential to both electrolytes in treating scheelite. Although its main function is to react with or flux the CaO, it also increases the bath fluidity. Temperature studies revealed optimum ranges between 900° and 1,100° C.; 900° C. proved satisfactory for tungsten trioxide, and 950° to 1,050° C. for scheelite. Current efficiencies were satisfactory for all current densities ranging from 10 to 57 a./dm.2. Yields were 400 to 650 g./kw.-hr. over the same current-density range. Crystal size and purity of the product are functions of temperature, current density, and amount of impurities in the electrolyte. Deposited crystals vary in shape from spherical grains to clusters of dendritic hexagonal needles, and in size from smaller than 35 to 570 microns. The purity of the tungsten metal produced ranges from 99.7 to 99.94 percent.

Jan 1, 1959

By R Simcock

Why Rehabilitate? Legislative Requirement Land rehabilitation is a condition of resource consents for mining. Clause 17 (1) of the Resource Management Act 1991 (duty to avoid, remedy, or mitigate adverse effects) provides the legislative basis for local authorities to impose resource consent conditions requiring land to be rehabilitated to approved uses during and after mining.

Jan 1, 1997

By David G. Almond

"Economies of scale and the variable characteristics of many large ore deposits have resulted in grinding installations having large SAG mills fitted with variable speed drives. Problems associated with effective operation of this equipment has created the need for better operator knowledge of mill load behavior and the need for new instrumentation capable of providing accurate information about load movement and composition. This paper discusses two performance enhancing instruments available to address these needs.INTRODUCTIONThe economic demands of new mining projects has resulted in increased equipment sizes and this is particularly evident in milling where there are now many SAG mills operating in the range of 28’ – 40’ diameter with installed powers of 8 – 22 MW. These mills are designed to process very high capacities of ore daily2 and the variable characteristics of many of the deposits mined results in the need to vary the mill speed during processing to cater for the changes in ore hardness. Mill speed changes often result in operational problems associated with high-energy impacts striking the mill liners reducing energy efficiency as well as degrading the grinding media through breakage, accelerating liner wear and in extreme cases even breaking liners. These operational problems have given rise to the need to have instruments aimed at providing operators with accurate information in real time about the load composition and movement within SAG mills.The original concepts for operating SAG mills were derived from past experience of operation of conventional fixed speed ball mills. However, the relatively stable conditions that applies with fixed speed and constant ball charge in ball mills supports theoretical approaches to the grinding process based on energy calculations such as Bond’s Work Index concept. Later a set of parameters Si and Bij were used for describing load kinetics, but all of these methods neglect the details of load movement and how the energy is actually used inside of the mill. It is now commonly accepted as a basic rule that SAG mills grind by impact whilst ball mills grind by attrition and consequently SAG mills are designed and operated to generate a large amount of impacts by the cataracting load without paying sufficient attention to where these impacts are actually occurring. Many mills are operated on the basis that as long as the mill is consuming the expected power there is little attention given to the class of bodies using this energy and this often results in the inefficient use of energy."

Jan 1, 2005

Current mine production planning, scheduling, and allocation of resources are based on mathematical programming models. In practice, the optimized solution cannot be attained without examining all possible combinations and permutations of the extraction sequence. Operations research methods have limited applications in large-scale surface mining operations because the number of variables becomes too large. The primary objective of this study is to develop and implement a hybrid simulation framework for the open pit scheduling problem. The paper investigates the dynamics of open pit geometry and the subsequent material movement as a continuous system described by time-dependent differential equations. The continuous open pit simulator (COPS) implemented in MATLAB, based on modified elliptical frustum is used to model the evolution of open pit geometry in time and space. Discrete open pit simulator (DOPS) mimics the periodic expansion of the open pit layouts. Function approximation of the discrete simulated push-backs provides the means to convert the set of partial differential equations (PDEs), capturing the dynamics of open pit layouts, to a system of ordinary differential equations (ODEs). Numerical integration with the Runge-Kutta scheme yields the trajectory of the pit geometry over time with the respective volume of materials and the net present value (NPV) of the mining operation. A case study of an iron ore mine with 114 000 blocks was carried out to verify and validate the model. The optimized pit limit was designed using Lerchs-Grossman?s algorithm. The best-case annual schedule, generated by the shells node in Whittle Four-X yielded an NPV of $449 million over a 21-year mine life at a discount rate of 10% per annum. DOPS best scenario out of 2 500 simulation iterations resulted in an NPV of $443 million and COPS yielded an NPV of $440 million over the same time span. The hybrid simulation model is the basis for future research using reinforcement learning based on goal-directed intelligent agents.

Jan 1, 2008