Search Documents

By Ronald J. Mathis

The objective of this contract is to design, build, surface test, and evaluate a breadboard prototype of the Variable Wall Mining System so that data are available for the design of a production machine. The Variable Wall Mining System (VWMS) consists of a series of side cutting augers, connected end to end, and distributed across a panel. Supplying rotary power at the end of the string and anchorage from conventional longwall roof supports, the augers are sequentially thrust into the face and then lifted to the roof to extract the coal in a continuous manner. The augers not only cut but also transport the coal. The effort described in this report summarizes the operation characteristics of the VWMS, the design methodology used to develop various working models, the surface testing of a ½ -scale version of the VWMS, prediction of power requirements and performance potential of a full-scale system, and a critique of the VWMS concept, conclusions, and recommendations.

Jan 1, 1987

By Leonello Sciacca

Deepening of harbours has become a priority, necessary to the ongoing operation of the wharves in the face of deeper draft merchant vessels and cruise ships. It is now standard practice in many areas to provide for harbours to be dredged to significant depths below mean sea level, in the order of 12.00 m (39 ft) for existing berths and 15.00 m (49 ft) for new wharf construction. The Ravenna Port Authority initiated a project to deepen the harbour bottom at selected wharves to a depth of 12.00 m (39 ft). In preference to reconstruction of the wharves with longer and heavier sheet piling or other equally disruptive reconstruction, they identified the structural reinforcement of the existing wharves by means of deep underwater tie rods as a possible alternative cost-effective solution. Having defined the design concept, effort was concentrated on developing the required technology. A technique, already in use for the installation of tie rods by means of robotics, was identified as potentially suitable for underwater use. It was decided to carry out the fine tuning and the evolution of the technology for a marine environment of the robot unit and of the related remote control software that controls the installation of the tie rods. An experimental test site was set up to refine the drilling, installation, grouting, monitoring and testing of underwater tie rods. The purpose was to confirm the feasibility of the proposed solution and the reliability of these tie rods for use in the reinforcement and construction of wharves. The paper also discusses the theoretical and experimental study of underwater tie rods dealing with the theoretical analysis of the interaction between tie rod and soil, aimed at identifying the correlation between the forces of applied traction and the corresponding measured elongations. A series of tests were carried out with positive results, both at the operating load of 300 kN (67 kips) and at the nominal maximum load of 630 kN (142 kips). The tests were carried out on seven tie rods, of which three were installed at a depth of 5.00 m (16 ft), principally to test the reliability of the operating and remote control systems in the presence of a significant hydrostatic pressure, and four were placed at a depth of 8.00 m (26 ft) to check the load bearing capability of the tie rods positioned at the depth called for by the current project.

Jan 1, 2011

By Y. Paul Chugh

NIOSH and the Illinois Clean Coal Institute are funding studies on characterization of coal and quartz dust in Interior Basin mines since 2009. Coal dust characteristics vary significantly and, are vital for the development of the engineering controls. This paper presents wettability characteristics of coal dust with respect to its chemical and physical properties, since wettability is considered to be a primary dust control technique. Particle size distribution, inter-particle interactions during wetting and quartz associations with organic and inorganic matter in coal seams is critical for understanding wetting phenomena. Silica content in the un-wetted fractions was found to be very high during wetting tests. Wetting of quartz may be limited by its association to hydrophobic materials as well as buoyancy forces resulting from particle size characteristics and particle-particle interaction in the wetting agent. Temperature of the wetting solution and effective contact time between dust particles and water droplets are found to be two important variables affecting the wettability. The characterization data obtained from this study can be utilized to develop engineering controls.

Jan 1, 2011

By C. L. Reichardt

Mining companies are increasingly looking to the developing world for the next generation of mining projects, often in countries that have little or no previous history of large-scale mining. One of the major challenges for such projects is hiring?and retaining?personnel that have technical skills and experience in mining-related disciplines. Staffing a mine with an expatriate workforce is neither cost-effective nor sustainable, and many countries now insist that mining companies ?transform? the profile of their workforce to more closely mirror the demographic profile of the host population. The need to nurture mining-related skills in emerging mining nations is not solely limited to the workforce: there are also pressing economic and sustainability imperatives to develop capacity within local service providers such as consultants and contractors, as well as to facilitate informed engagement between mining companies, government and civil society. However, few educational institutions in emerging mining nations currently have the ability to offer practical training in mining-related disciplines. Local employees who are sponsored by companies to develop their skills through international study maybe impeded by language and cultural barriers, and may also be taught using course content that is of limited relevance to the specific challenges of their future working environment. This paper addresses the challenge of skills development and retention in emerging mining nations and uses examples from sub-Saharan Africa and the Asia Pacific region to explore practical means of developing capacity in mining-related disciplines. It examines the need for companies to implement strategies to develop local technical capacity in countries where they envisage a long-term operational future and also highlights the need to foster partnerships between academia, developmental institutions, mining companies, governments and civil society to establish the critical mass of mining-related skills required to nurture the development of a sustainable mining industry.

Jan 1, 2009

By S. D. Viljoen

The use of ceramics to protect equipment subjected to wear in abrasive and corrosive applications has been accepted by most plants as the industry norm. Little is, however, known about alternative special ceramic based products which are available for the protection of plant assets. With careful engineering, impact resistant ceramics can be used in high impact zones using modern ceramic technology. Properly selected and properly installed, ceramics will provide a tough wear resistant lining for protection against abrasion and impact. Basalt, on the other hand, is widely used in coal washing plant process pipes with varying degrees of success. Basalt is normally not used for the lining of bends, ?T? pieces or reducers due to the reduced wear resistance compared to alumina ceramic. The advantage is a much reduced initial capital cost. A patented ceramic composite non-return valve solved an old problem encountered in the operation of medium sumps. The design approach overcomes the lack of functionality of alternative designs and reduces valve wear while preventing medium settlement during plant shutdown periods. Direct bonded ceramic pulley lagging is becoming the industry norm, eliminating most of the problems encountered with conventional pulley lagging systems.

Jan 1, 2010

By S. H. Ash

THE BARRIER-PILLAR SYSTEM in the Lackawanna Basin consists of 93 barrier pillars between Archbald and Taylor, Pa. These pillars affect 48 mines, have a total length of 87 miles, and confine 21 underground pools, which contain more than 10 billion gallons of water. From an investigation of size, position, and condition of the barrier pillars, it is apparent that those concerned are uncertain, not only as to the method by which the sizes of the barrier pillars were determined but also as to the stability of those that may be expected to act as dams. Where a barrier pillar must act as a dam, its failure may result in loss of life, the mine, or both; it would be far better had it not existed and thereby given a false sense of security.

Jan 1, 1952

By D. Govender

In recent years, economies of scale have continued to drive copper projects to larger throughputs to offset depleting lower grade resources. A decade ago there were only a small number of projects that stretched beyond 100,000 Mtpd throughput rates. Nowadays and moving forward virtually all the major copper projects are sized beyond this, with throughput rates up to 250,000 Mtpd now under evaluation for a number of key projects in Chile and Peru. This paper explores the development from the 160 m3 flotation cells, through to the 257 m3 cells and nowadays to the 660 m3 machines. The contributions of specific copper concentrators to this growth phase are reviewed herein. The historical basis of flotation machine scale-up is also briefly discussed. Metallurgical results as well as layout, maintenance and operational aspects are highlighted.

Feb 27, 2013

By Grant P. Cordon

Our subject, "Safety, Legal, and Contracting," is a range of topics which covers a broad spectrum, but is obviously Intended to focus our attention upon certain particular aspects of tunnel problems. These are all fascinating and complex subjects, and others are much more qualified to discuss to discuss the fine points involved. Put after some 45 years' involvement as an inspector, engineer, contracting officer, and especially for the last 22 years as a contractor's estimator and manager, I have developed some strong and definite convictions to share with you. I hope it will serve to get you started thinking. My first tunnel experience was in a soft ground tunnel which was dug by hand, literally. The crown or arch back was taken out, a pebble at a time, by bare hand. The face was constantly breast-boarded, and the mucking was all done by hand shovel. My first rock tunnel was drilled by hand held drifters from the muck pile. Since then, most tunneling techniques have improved greatly. The jumbos, booms, muckers, and moles have taken over many of the back-breaking chores, and reduced the manpower requirements.

Jan 1, 1974

By R. Reed von Gal

The majority of zinc strip produced in the world today is cast on the Hazelett twiri-belt continuous casting machine. Ten of these machines are currently operating worldwide, and one machine is under construction for the People's Republic of China. The caster, which was first patented in 1947, was originally developed for aluminum and copper alloy casting. In the early 1960s, the design was expanded into zinc casting and within ten years the industry had essentially converted from casting and rolling ingots to twin-belt continuous casting with in-line rolling. The casting process employs two parallel, moving. water-cooled belts as the major mold surfaces. Together with two strings of side dam blocks, the design offers a four-sided moving mold which produces a continuous strip or bar. This paper will cover a bit of, the history, as well as the current technology surrounding this high production process for zinc strip production.

Jan 1, 1990

By Mark A. Williams

"This paper was originally intended to be a presentation of a case study of two surface bituminouscoal mines in the southern Appalachian coal fields located within five miles of each other. These mines were nearly identical in every aspect from geologic setting to equipment application. Althoughrepresentatives from each mine desired to participate in the preparation of this paper through support in providing background information and in review and editing, it was later concluded that, due to the environmental sensitivity associated with each mine, it may not have been a good decision to present this case study in a public forum."

Jan 1, 1994

Grouting is mainly used to improve mechanical properties or decrease the permeability of rock mass around civil and mining projects. The purpose of this paper is to present the most effective factors on grout penetration depth in rock mass. Such factors are essential for reliable estimation of the grout penetration depth and the expense for cement take of any grouting project. In this paper, about 50 different types of the relations presented so far by various researchers to estimate the depth of penetration in fractured rock were studied. The effective factors are classified to rock mass properties, grout properties, and operational factors. Results show that firstly, the discontinuities aperture and Lugeon value are respectively the most investigated factors of rock mass properties influencing on penetration depth. Secondly, the yielding stress, viscosity, and density of grout are the most effective factors of grout properties. Finally, grouting pressure has an intense effect among other operational factors. The investigations were also verified in Siah Bishe dam case study. Keyword: grout penetration depth, rock mass properties, grout properties, operational factors.

Feb 27, 2013

By Shawna Munn, Jakub Hudler

This paper outlines the use of tunneling headwall softeyes for transit construction projects in the Greater Toronto Area (GTA) over the past decade. Due to spatial constraints, tunnel boring machines were used to construct the underground tunnels requiring the design of launch and exit shafts with headwall softeyes to facilitate tunneling operations. Variable ground conditions and shaft geometries lead to the development of innovative headwall and tunnel softeye design applications using fiber reinforced polymer (FRP) elements (beams, reinforcing bars, and tiebacks). This paper outlines the challenges and benefits associated with designing and constructing shafts using various systems. Lessons learned throughout design and construction of more than 20 structures over the past 10 years are outlined. The constructability challenges with using FRP and design performance are also discussed. For over a decade, the City of Toronto has been expanding its metropolitan transit network with a variety of new transit construction projects. Two recent projects in the Greater Toronto Area (GTA) for underground infrastructure include the Toronto York Spadina Subway Extension and the Eglinton Crosstown Light Rail Transit project. These add a total of 31 new stations and 18.6 km (11.5 miles) of underground transit (TTC 2017) (EllisDon 2016). Due to ground conditions and spatial constraints of existing surface infrastructure, these projects utilized tunnel boring machines (TBMs) to construct the underground tunnels requiring the design of various types of shafts and headwalls to facilitate underground tunneling operations. To allow for tunneling through the headwalls, these shafts were designed with “softeyes” - a section of the wall without metal reinforcement that allows the TBMs to tunnel through.

Jan 1, 2018

(This paper reviews the reasons for and the principles followed in designing and constructing complete new surface works at the mine of the Zinc Corporation Limited, Broken Hill, New South Wales, and describes the layout, plant, buildings and services.)The Zinc Corporation mine produces high grade lead, silver and zinc sulphide ore. Lead and zinc concentrates are sent by rail to Port Pirie, where the lead is smelted and the zinc concentrate is shipped to Tasmania, England and other overseas countries.Some time ago consideration was given to the advisability of sinking an additional shaft. For some years the old main shaft had been working at full capacity and developments underground had indicated that the mine would eventually be capable of an output greater than that which could be handled through the shaft. It was therefore decided to sink a new main shaft and the site chosen was in footwall country 900 feet south of the old main shaft. The reason for the move south was so that the new shaft would be opposite the centre of gravity of the ore-bodies at depth. The size of the new shaft is 27 ft. ,6 in. x 15 ft., and the work was put in hand early in 1936.It was intended to haul the whole mine output through this shaft, which was 1,600 feet from the mill then operating. An extensive conveyor system thus became necessary unless a new mill was built near the shaft. A careful study of the situation was made by the management and consideration was given to requirements for expansion, the condition of...

Jan 1, 1940

By M Blanch

Gas management practices across the Australian underground coal industry have evolved significantly since the early nineties with the introduction of hazard management plans, directional drilling techniques, surface gas predrainage methods, and the widespread use of ventilation and gas reservoir simulation software.The improvements are evidenced by a substantial reduction in the occurrence of outbursts and gas related delays during a period where coal production rates have increased three to four fold. The development of effective gas predrainage strategies have been afforded by the use of reservoir simulators and a significant increase in the availability of measured gas reservoir data, in particular gas content and composition, adsorption isotherms and permeability. That said significant opportunities remain to optimise gas drainage designs and increase certainty in the gas predrainage design process through an enhanced understanding of coal seam permeability and how it is applied in the gas drainage design process.This paper describes the discrepancies between measured and actual seam permeability found during the recent assessment of two pilot predrainage programs executed in the coal measures of Queensland’s Bowen Basin. The results of those programs illustrate the need to better understand the validity of measured permeability data. The history match method employed in the pilot well assessments is proposed as an integral step in the routine gas drainage design processes that will ultimately lead to increased certainty and flexibility in gas predrainage practices.CITATION:Blanch, M, 2017. Coal seam gas predrainage optimisation through an enhanced knowledge of coal seam permeability, in Proceedings Australian Mine Vent Conference 2017, pp 73–78 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

Coking coals are very much in demand on a world wide basis, particularly the higher rank coking coals, which form an important part of many coking blends and which represent the smallest portion of the world'scoking coal reserves. Conventional coke oven plants, using these coals, will predominate at least until the next century.Blending schemes for conventional coking require definition of the basic properties of coals so that the factors influencing the carbonization behaviour may be assessed. Several concepts, which are relatively simple, ate available to help promote a better understanding of the bask factors controlling -coke strength and are also useful in suggesting possible lines to follow in the blending of coals for coking.The interpretation of carbonization behaviour and coke structure in terms of petrographically defined coal rank and type provide a basis for planning and exploitation of coal Teserves. The optimum parameters for coking are suggested as follows.1. Type- Vitrinite content (% m.m.f. by volume) 55 ± 5%2. Rank- Mean maximum reflectance of vitrinite 1.30 ± O.10% Carbon content of vitrinite (% d.m.m.f.) 87·5 ± 1·0%The value of a coal should be assessed in relation to all its possible uses in blends. This is a more realistic and productive approach, as compared with considering coals only in relation to the results of blending with"good" coking coals. Blending schemes have been outlined to assist in the assessment of the blend potential of coals of all ranks and types.Reserves of higher rank coking coals in N.S.W. are very limited and should be conserved by blending with the low rank coking coals, of which there are large reserves.Examination of blending theories in relation to N.S.W. coals suggest that blends in the broad categories of minimal downgrading of the higher rank N.S.W. cok...

Jan 1, 1972

By Thompson D. R, Milton R, Perry K. M A

From the Department for Research in Industrial Medicine (Medical Research Council), The London Hospital; and the De Havilland Aircraft Company:M.R.C. INVESTIGATIONS IN 1936In 1936 the Industrial Pulmonary Disease Committee of the Medical Research Council investigated both clinically and radiologically a group of fifty workers who had been exposed for a number of years to the inhalation of alumina in the reduction factory of the British Aluminium Company. The results are shown in Table 1.They also considered the sickness records of all the workers (Hill, 1936), as compared with those in other parts of the factory (Table 2).

Jan 1, 1945

By R. E. Murray

"It is a gloomy moment in the history of our country. Not in the lifetime of most men has there been so much grave and deep apprehension; never has the future seemed so incalculable as at this time. The domestic economic situation is in chaos. Our dollar is weak throughout the world. Prices are so high as to be utterly impossible. The political cauldron seethes and bubbles with uncertainty. Russia hangs, as usual, like a cloud, dark and silent, upon the horizon. It is a solemn moment. Of our troubles, no man can see the end." By now you, no doubt, are asking, 'Where did Murray get this bit of philosophy?' Well, I obtained it from an editorial entitled. "The Worst of Times", which was published in the Harper's Magazine in 1847. That's right, 1847! The parallelism between the situation in our country at this time and in 1847 is un- canny. But wait, there is one major exception the size of government. To my knowledge, the citizens of 1847 were not stifled by the extreme governmental excesses that we are experiencing today.

Jan 1, 1980

By Roberto Folchi

This note deals about the controlled demolition work for the dismantling of an industrial structure in San Seplocro, Italy. The structure to be demolished, the FLOWERS SILOS, consisted in a multilevel reinforced concrete frame supporting r.c. silos and steel silos. This was standing near civil buildings and was adjoining a warehouse that had to be safeguarded for being renewed.

Jan 1, 1994

By Robert Jakiel

The following paper is being presented to provide an understanding of the Deep Soil-Cement Mixing (DMM) performed at Contract C09A7 at the Fort Point Channel Site (FPC), for the I-90/I-93 Interchange of the Central Artery/Tunnel Project (CA/T), Boston, MA. The paper is written as a summary of the DMM from the DMM Contractor's perspective. The summary provides technical information and practical observations that are currently considered to be state-of-the art knowledge within the soil mixing industry. The observations and information are being provided by Robert L. Jakiel, Chief Engineer of SMW Seiko, Inc., who was the DMM Project Manager and Project Engineer for the A7 Joint Venture at FPC. The DMM was started in April of 1996 and completed in December 1999. The various acronyms and terminology used to describe the soil mixing are found in a section at the end of the paper.

Jan 1, 2000

By Gaby Steinbach

A novel synthesis is described for the preparation of supported gold catalysts for low-temperature CO oxidation. The novel route is a variation of the inverse co-precipitation method and requires amphoteric metal hydroxides, with zinc and aluminium hydroxides chosen. Catalysts were prepared by inverse co-precipitation (ICPa) and by the novel route (ICPb) and tested for CO oxidation at 60ºC. Preliminary results showed the novel route to be superior to ICPa; the catalysts prepared by ICPb showed higher catalytic activities. The effect on catalytic activity of parameters such as pH, calcination temperature, washing of precursor and calcined catalysts and ageing was investigated. A preparation pH of 9 and a Zn to Al mass ratio of 3 proved to be optimal. It was possible to remove residual chloride by washing thereby enhancing catalyst performance. Ageing and Mg citrate addition were also shown to improve catalyst performance. Characterization of the catalysts revealed that better activities were obtained when the support was more crystalline and had a higher surface area. The presence of carbonate-containing species in the support decreased catalytic activity. 197Au Mössbauer Spectroscopy revealed the presence of Au3+ when catalysts were heat-treated at temperatures of 200ºC and below. Catalysts calcined at 400º had 75% of the gold present as Au0, with the remaining gold present as Au3+.

Oct 1, 2003