Search Documents

By W. R. Dengler

Dynatec Mining Limited contracted to sink a lS00 metre (4960 ft.) concrete lined shaft for Falconbridge Nickel Mines in Sudbury, Ontario, Canada. The shaft is 6.3 metres (20.S ft.) in diameter inside the concrete lining and is equipped with steel furnishings. Dynatec used the owner supplied 4.6 metre (l5 ft.) diameter double-drum hoist to sink the shaft with 12.S tonne buckets for muck removal and 4 cubic metre concrete buckets for concrete placement. One of the unique features of the shaft sinking operation is the use of a four-boom electric hydraulic drill jumbo permanently mounted in the shaft sinking stage. This paper will describe the performance obtained with the electric hydraulic drilling equipment and the high capacity muck removal and concreting equipment.

Jan 1, 1992

By António Fiúza, Anthony Danko, Patrícia Leitão, Aurora Futuro, Cristina Vila, Lurdes Dinis

The average global recovery rates for processing scheelite ores by physical methods are normally in the range 50 to 70%, and it is problematic to attain a minimum grade of 60% WO3 in the concentrates without penalizing further this yield. Direct hydrometallurgical processing of low-grade concentrates or medium- to high-grade ores may become an interesting global economic alternative as it allows increasing the recovery rate, avoiding major penalizations due to the grade of the concentrate and increasing the added value of the final product. Leaching of scheelite by sodium carbonate presents several advantages such as its selectivity regarding the dissolution of troubling metals like iron and aluminium, allowing for a simple and flexible process diagram. However, it has the disadvantage that it is performed at high temperature and pressure with a high consumption of reagents. The feasibility of leaching is appraised by the extraction yield and selectivity, but also by the operating cost. Considering these aspects, a relevant objective of the research was to transform alkaline pressure leaching into a feasible processing alternative directly applicable to both medium- and high-grade ores and simultaneously to low- and high-grade concentrates produced by physical methods. The research used ore samples and low-grade concentrates from a typical skarn orebody as well as high-grade concentrates from a chalcopyrite-scheelite orebody. Different operating conditions were tested. Temperature, pressure and reagent concentration showed to be fundamental, but not exclusive, in determining the leaching behaviour. The operating conditions are milder than the ones generally proposed in the literature or currently in use in industry, but with higher carbonate consumptions. The research was oriented towards potential industrial implementation allowing for the application of optimization methods and straight scale-up to pilot-plan design and project.

Taking the third meridian as the eastern boundary of proved payable auriferous country, there is a stretch of country, nearly 600 miles in width, in which no appreciable amount of gold has yet been discovered. Many prospectors have attempted to .penetrate or traverse it, but comparatively few have thought it worth while proceeding with the examination.The desolate stretch of waterless desert-the very few and insignificant outcrops through the sand and the almost total absence of feed for horses have, combined, presented such a barrier as to preclude prospecting. The few who have traversed the country are eloquent in denunciation, yet their investigations, necessarily hurried, are not quite satisfactory. The absence of water utterly debars a thorough examination being made. Gold may exist in quantity, yet it would have to be extraordinarily plentiful to render its obtaining profitable. Too fantastic is the idea of its ever being a mining district; shifting sand to traverse, utter absence of wood and water render the notion absurd. Likely looking belts occur, but these in all "cases are small and remote from water. Gold has been obtained from likely look ing quartz reefs, but only by fire assay, and then but a few do to the ton. Without wishing to be pessimistic, I would unhesitatingly declare that east of the third meridian, and between the parallels 25 and 30 degrees in West Australia, there is no gold in payable quantities.

Jan 1, 1901

Greymouth River Dredge û Birchfield Minerals Ltd Blackwater Gold Mine û Macraes Mining Company Ltd Globe Progress Gold Mine û Macraes Mining Company Ltd

Jan 1, 1996

By George L. Gates

[When clays are mixed with water to -.,tee mud fluids for use in trilling wells for nil and --ac b ;l-,e rotary method the liquid mixtures have certain physical characteristics that vary with the quantity and size of their inherent solid particles. All naturally occurring clays contain variable quantities of particles of different sizes ranging from relatively coarse (sands) through -,.tedium (silt) to fine materials of colloidal dimensions. Tie colloid content is extremely important 2.s a desirable _.'ale constituent of mud fl-z to fit well drilling. ';'it:-out colloids the souk?;,' in a mud fluid wouldr rapidly, end ti-c-and. wall-building qualitites of the' fl,-,id would l ..o r re 1 impaired. Mud .fluid.^ with insufficient quantities of colloids also are lacking in "lubricating" g listen, and it is, to ° min casing in, -)re holes drilled with such fluids.]

Jan 1, 1941

By Daniel Su

This paper describes recent ground control challenges encountered at the longwall recovery areas of one of Bailey Mine?s two longwall faces and the proactive measures taken by CONSOL management and engineering to mitigate them. The challenges derived primarily from the following causes: (1) irregular roof coal and draw slate thickness, (2) presence of thick sandstone at the recovery area and extremely weak rocks below the sandstone, (3) close proximity to a regional anticline, (4) low shield set pressure and tip load, and (5) ineffective primary roof support that led to progressive failure of the headgate roof. The presence of the anticline contributed to extensive fracturing of the sandstone. Excessive pot-out in advance of the shields frequently occurred near mid-face due to the presence of thick draw slate and irregular roof coal near the recovery area. This, in turn, resulted in face heights that exceeded the maximum reach of the shields. Subsequently, during longwall meshing, when the advance rate slowed considerably, fractured sandstone would often break loose, causing the shields to yield, thereby reducing the height and inhibiting shearer movement. To improve the headgate and face conditions within the longwall recovery area, several actions were taken, including: (1) assessing site-specific roof geology by conducting in-mine roof coring around the recovery areas and by mapping immediate draw slate and roof coal thicknesses within surrounding entries, (2) increasing pump pressure and thus shield set pressures (3) diligently monitoring shield set pressures and longwall extraction horizon, (4) installing additional cable bolts and roof screening to prevent progressive failure of the immediate headgate roof, (5) fully-grouting supplemental cable bolts to improve headgate support stiffness, and (6) gluing the headgate roof within the recovery areas with polyurethane. As a result of these collective efforts, longwall recovery delays at Bailey Mine were reduced from 21 days in 2006 to nearly zero in 2009.

Jan 1, 2009

By Pengfu Tan

Xstrata Copper at Mount Isa in Australia has operated one copper Isasmelt furnace and four P-S converters. The phenomena of foaming occur in above 10% of converter operations. A thermodynamic model of copper P-S converter and a viscosity model of converter slag have been developed to simulate the slag blow and copper blow. The model predicts the chemistry and viscosity of copper skims during copper blow. The effects of oxygen potential, charge of dirty materials, slag carry-over, under-blowing, over-blowing, and temperature on the foaming and viscosity of copper skims have been discussed. Some improvements of the industrial operations have been presented.

Jan 1, 2006

Gold in the stibnite veins of Costerfield, Victoria, was described in 1922 1, prior to any mineragraphic examination, as (a) free yellow gold (b) free rusty gold and (c) combined gold. The free yellow gold occurs in quartz and will amalgamate with mercury. The free gold of dull, rusty or copper-red colour occurs in massive stibnite and has been stated to resist amalgamation with mercury. The dull colour is only skin deep and the colour is bright when the rusty gold is scratched. The appearance of the rusty gold is spongy or cellular and it generally occurs near small cavities in the stibnite. The suggestion that the cellular character indicated the removal of a certain amount of stibnite leaving a residue of se.condary gold cannot be sustained.It now appears probable that the rusty gold is formed by the primary dissociation of a gold antimonide and is distinct in origin from the normal yellow gold which is deposited with quartz or stibnite from auriferous mineral solutions.The combined gold referred to in the earlier paper was the gold contained in the stibnite as revealed by assay. Such gold was at first thought to be either dissolved in the stibnite or else present as free interstitial particles too minute for observation in transmitted light in thin sections.Subsequent examination of numerous polished,surfaces disclosed the small particles of gold occurring in the grain boundaries in aggregates of fine grained stibnite 2. The assumption that all the gold in the stibnite, as revealed by assay, occurred in this way is now known to be incorrect, because limited amounts of a gold antimonide have been found in the veins.

Jan 1, 1952

By Rick Wilkins

The stability of steep embankments is a major safety issue in open pit mining, highway passes, and earth filled dams. A failure in any one of these situations could mean a loss of very expensive equipment, a long term inconvenience, and more importantly, a loss of life. These possible catastrophes could be avoided by installing a reliable real time monitoring system. Robotic total stations (RTSs) give one possible cost effective solution to creating a near real time monitoring system. Repeated surveys at predetermined time intervals can automatically generate warnings if slope movements exceed a preset tolerance level. The variation in atmospheric refraction, combined with possible instabilities in reference targets, can make a monitoring system based on RTSs produce false alarms. A methodology has been developed at the Canadian Centre for Geodetic Engineering (CCGE) for reducing these systematic error effects. The methodology has been realized in the creation of a software package that has been successfully implemented at large earthen dams in California and at an open pit mine operation in British Columbia.

May 1, 2002

By John Wise

Significant movement to an existing slurry wall which serves as a retaining wall on 'O' Street in Southeast Washington, D.C. initiated the Department of Public Works for the District of Columbia to invite specialty contractors to propose a rehabilitation and stabilization for the failed slurry wall. Nicholson Construction Company proposed and was awarded a contract for the construction of an anchored precast lagging and soldier pile wall to be located approximately 4 feet in front of the existing structure with granular fill placed between the new and existing walls. Stabilization of the existing slurry wall also included drilling horizontal weep holes and demolishing the failed panels down to the existing ground surface. A new and improved drainage system was also constructed to increase the amount of water directed toward the existing storm sewer system running along 'O' Street. This paper provides a detailed account of these construction activities.

Jan 1, 2003

By R. M. Tyler

The importance of the heavy mineral sands to southern African economic well-being cannot be over emphasized. The value of the worldwide titanium dioxide industry is estimated at $7 billion. Six out of eight of the world?s proposed new project areas are in southern and eastern Africa, and a seventh at Tamil Nadu in India is partly owned by a South African company, Kumba Resources. The HMS industry can be highly lucrative; its return on capital is the best in the mining industry. There are, however, problems, particularly in the smelting technology. The often considerable affect of mining on environmentally sensitive coastal dunes is also becoming increasingly important. The medium-to long-term demand for Ti-dioxide pigment and ceramic grade zircon appears very healthy. If, as predicted, the costs of producing titanium metal can be reduced, then there is huge potential for the metal. In summary, the HMS industry is an attractive one to be in, with good returns and generally manageable risks. New business opportunities and their economic implications for Africa are discussed.

Jan 1, 2004

By Hwasoo Park

Keywords: FC mold, Argon, Magnetic, Solidification Fluid flow plays a significant role for steel surface quality in continuous casting. Although water models are able to model fluid flow, the flow pattern is not of practical interest since the moving solidifying shell cannot be accounted. Computer modeling has become a popular and dependable tool to analyze the complex phenomena occurring in continuous casting. In this numerical simulation we coupled momentum and energy equations considering the solidification of steel along with turbulence ?-e model. The vertical bending mold is equipped with bifurcated nozzle with 15 degrees of port angle. FC mold is supplied with DC induced magnetic fields. Influence of argon and magnetic fields on molten steel flow and heat transfer is investigated by solving momentum equations adding source terms due to multiphase ? magneto hydrodynamics. The results show that magnetic fields reduce the jet velocity from port by lower magnetic core induced field but the influence on meniscus velocity is complex to describe. Magnetic fields increase surface temperature and homogenize its distribution on surface and inside a mold.

Jan 1, 2005

By Joan Stoupa

The expansion of the West Point wastewater treatment plant located in Seattle, Washington, will require a permanent tieback retaining wall to enlarge the plant site for the new treatment plant facili­ties. The retaining wall will extend approximately 3,000 feet along the property boundary between the treatment plant and the neighboring Discovery Park. Wall heights will range from 35 to as high as 65 feet. The purpose of the retaining wall is to provide a more uniform grade on the plant site and to resist lateral pressures exerted by the upslope, unstable hillside. During preliminary design of the retaining wall, various wall systems were evaluated based on assumed subsurface soil conditions. Results of preliminary studies indicated that expected subsurface conditions and wall heights made a permanent tieback retaining wall feasible. However, uncertain loads on the wall and the capacity of anchors in the native soils were significant. As a result, a detailed geotechnical program was conducted. The scope of the program included conventional drilling, sampling, analyses, and a field test program to determine site-specific anchor capacities. This paper describes the anchor test program and results.

Jan 1, 1990

By R. G. Vardiman, M. R. Achter

Observations of dislocation structure in niobium are presented using two techniques. Triangular pits developed by electroetching are confined to orientations in the stereographic triangle between the (111) pole and planes of the (1ll) zone and require the presence of carbon. Some unusual electroetching phenomena at other orientations are noted. A chemical etch of dislocations decorated by the addition of carbon to 50 ppm reveals the complete dislocation line structure in a surface layer up to 30 p deep, with a resolution of less than 1 p. This effect is independent of surface orientation. The structure of subboundary nets may be resolved for misorientations up to about 1'. Dislocation structures found in strain anneal grown crystals, such as helices, prismatic loops, and high-density areas, are observed. The measurement of dislocation density is discussed and values obtained in different ways are compared. IN the course of some work on the response of refractory metals to thermal-mechanical treatments, it was desired to examine the defect structure of relatively low dislocation density crystals of niobium in bulk form. Surface and bulk methods for the observation of dislocations have been reviewed by ~melinckx,' and include etch pitting, decoration, and various X-ray techniques. The dislocation line structure has been developed by decoration in a few metals, although observations were limited to certain orientations, or by the coarseness and nonselectivity of the precipitate. The most commonly used technique is etch pitting. In niobium, etch pits have been developed chemically'0," in material of high impurity content and electrolyti-cally'' in relatively pure material. In this paper, etch pits developed electrolytically, and the dislocation line structure of a surface layer developed by decoration and chemical etching, are examined, and observations are presented from both techniques. EXPERIMENTAL METHODS Our starting material was electron-beam-melted niobium, swaged to 4 or -in.-diam rod. Chemical analysis is given in Table I. Single crystals were grown by a strain anneal technique using 1 to 2.5 pct of strain and growth temperatures of 1700" to 2300"~.'~ Some crystals grown by zone melting were also examined. The desired surface orientation was exposed either by spark machining or by sectioning with a cut-off wheel and prepared for etching by electro-polishing.

Jan 1, 1969

By B. Farshadi, B. Asi, M. J. Habibian

"Dare-Zereshk deposit is one of the deposits supplies ore for Taft copper Complex in Iran Yazd province. This deposit is situated underneath a village the same name. Prior to mining activities, the village and its agricultural lands should be dislocated and deserted. This paper discusses about sustainability factors in this area including: Social and environmental effects of mining, dislocation and substitution of communities, created and lost jobs, financial and economic factors, quality of life index, infrastructures and post-mining land use. Studies have been performed by coupling Geographical Information System (GIS) with decision support tools such as Multi Attribute Decision Making (MADM), Through these studies revealed that considering the infrastructures developed for mine and plants, earned incomes and changing the community, mining activity in this area not only increases the social and regional sustainability but also improves it to a higher level."

Jan 1, 2011

By W. J. Spat

Political risk is an integral part of the mining business in northern Andean countries. Peru, Ecuador, Colombia and Venezuela all have a higher than average political risk compared with other South American countries. Successful operations require good political-risk information, a thorough political-risk-management plan and a strategy to deal with political-risk perception on the part of the investing public. Colombia is perceived as about the riskiest place in the world to do business. A selection of recent headlines reads: “Colombia on the brink” (Economist, 1998), “Colombia’s ship of state is sinking” (Insight on the News, 1998), or simply “Bad news” (US Catholic, 1998). The World’s Most Dangerous Places rates Colombia as “currently the most dangerous place in the Western Hemisphere, and perhaps the world” (Aral and Pelton,1998). And many prospective investors and analysts say to Greystar Resources: “Yes, we love your results, but Colombia?”

Jan 1, 2000

By Christopher Mark

Severe dynamic multiple seam interactions can occur when active mine workings are subsided by underlying mining activity. The most dramatic events are usually caused by longwall mining or pillar recovery beneath open, overlying entries. But pillars in abandoned workings can also fail and cause subsidence and damage an overlying mine. This paper describes a case history in which an apparent ?pillar squeeze? in the abandoned workings of a lower seam was initiated during retreat mining in an upper seam. The event subsequently extended more than 1,500 ft and ultimately closed the upper seam mine. Analysis indicated that the pillars in the lower mine were adequately sized for the lower seam mining and were not affected by the initial development above them. When retreat mining in the upper seam had progressed several hundred feet, however, the pillars located directly beneath the pillar line were overloaded, and an extensive squeeze initiated in the underlying workings. The squeeze, in turn, subsided the overlying workings, causing widespread rib falls and roof instability. Previous examples of dynamic multiple seam interactions resulting from delayed subsidence of underlying workings have been reported in the literature. This is, apparently, the first recorded incident in which pillar recovery in an active mine triggered pillar failure in an underlying mine, which then triggered a dynamic interaction that impacted the active overlying seam.

Jan 1, 2012

By D. A. Greenwood

Dr David Greenwood opened the first technical session of the conference by highlighting the diverse nature of the papers in this session but drawing attention to the common theme that each solved a particular problem. PAPER 1.1 Tony Elliott introduced his paper on deep mix-in-place soil/cement stabilisation by stressing its simplicity. The engineering solution adopted at Elland was detailed in his paper and had formed the key to success of the project. The process itself is not widely used or known in the UK, although it has the potential to achieve significant benefits, subject to proper engineering control being exercised. It was explained that although the concept was not new, development of the technique for soil modification was relatively recent. The alternatives to mechanical mixing are injection, which is very dependent on soil type, site geometry, etc, and jet grouting; both processes are soil-responsive, and not easily monitored or programmed, difficulties which can largely be overcome by mixing. To achieve this at depths to say 30m requires high-powered, high torque machines and has resulted in significant equipment development.

Jan 1, 1991

By L. Nichols, H. Keele, K. Czajewski

"The oil sands industry in northern Alberta disposes of the by-products of bitumen extraction into tailings ponds. The mix of tailings sand and mature fines, with gypsum added as a flocculent, constitute a waste stream called consolidated tailings or composite tails (CT). The two main challenges of the tailings disposal process are a chronic shortage of economical containment and the potential mobility of CT deposits in the event of breaching by, for example, long-term erosion, which makes abandonment of tailings ponds more complicated. Thick deposits of CT do not consolidate in adequate time to provide reassurance for abandonment of the CT containment facilities and that is why the containment must be adequately robust or the properties of CT improved for long-term stability. This paper addresses potential solutions to these problems by applying the gravity drainage of CT and quasi-homogeneous construction for containment facilities.Gravity drainage is suggested as a mechanism to facilitate the consolidation of CT in critical areas of the ponds by inserting internal sand layers within the body of the deposit. Critical CT areas are defined as areas around the perimeter of containment. The advantages of this solution are longterm stability of the disposal area by creation of stiff deposits around its perimeter and facilitation of reclamation efforts on its surface.The present solution for containment of CT deposits is not favourable from a materials balance point of view. In general, sand has become a valuable resource as it both forms the primary component of the CT matrix and becomes the containment building material. If sand is required for CT, less is available for dyke construction. This puts additional pressure on the industry as a whole to maximize the use of overburden and interburden for construction of tailings containment structures. Typically, only 50 percent of dry mine waste (overburden + interburden) is incorporated into dyke construction. The remainder of dry waste is stored either in waste dumps or in tailings ponds, consuming valuable in-pond space originally allocated to CT material. Quasi-homogeneous dykes are proposed to contain CT deposits rather than traditional minimum cross-section dykes built of overburden and/or cell sand. The quasi-homogeneous dyke may change the unfavourable material balance and lessen the construction constraints that are presently imposed on the mine/waste disposal process."

Jan 1, 2008

By V. Svalbonas

When the Trelleborg Divisions of Boliden Allis and Mineral Processing Systems (MPSI) merged, a unique opportunity occurred for two independent mill fabricators to compare design pro¬cedures and the research upon which they were based. Several semiautogenuous (SAG) mill analyses are compared using Boliden Allis and MPSI methods. The differences and similarities are then used in a correlation of critical stress definitions and the acceptable design and inspection criteria. Given the opportunity to compare the total philosophies and methods of several companies involved in the design and fabrication of grinding mills, it was important to first develop the comparison method and ground rules. One option was to compare analytical methods by details such as numerical techniques and accuracies. However, this option was discarded in favor of a more general approach. The question that was finally posed was in two parts. Given an identical mill requirement: • What would be the difference in the analytical design result, and to what aspect of the analytical process could this difference be attributed? • What would be the difference in approaches to obtaining the final hardware in subcontracting, both in specifying and Quality Assurance surveillance? By using this comparative approach, questions of relative conservativeness and reliability would automatically be answered.

Jan 1, 1992