Search Documents

By A. Haxhiaj, E. Haxhiaj

"The paper has as a studying object the issue of effective management of gasses’ heating and dusts in reductive melting process in lead (Pb) metallurgy. It also analyses the issue related to the usage and recycling of dusts and gasses in all pyro-metallurgical processes of technical lead production. The paper contains the analysis of technological process of separation of humidity, gasses, and dusts of valuable remainders in “Trepça” plant. Paper has the results of theoreticalexperimental studying, analytical and graphical of gasses thermal balance depending on height and composition of load, and the coke quantity on load for reductive melt in “Water-Jacket” furnaces. With thermal balance, having into consideration all parameters of heat in entry and exit depending on aforementioned factors we aimed to optimize the parameters of the process, keeping the attention to the minimization of energy consumption, and the overall influence on environment.1. IntroductionThe upper part of the furnace which is the study point of this paper lies from the reactions zone of Water-Jacket furnace and it also includes the furnace neck. In this zone has been elaborated the zonal material balance referenced third in the row. The separation of humidity, dusts, gases and lead with gases depends on many parameters like temperature, load composition, and height of load inserted in the furnace, and also the height of preheating zone in Water-jacket furnace. Lead oxidizes in reaction zone of the furnace and exhales with gases like dusts and small particles after which falls in worthy storage of Trepça plant and has negative effects in environment, and economic stability of reductive melting process of Water-jacket furnace. Thermal balance of gases in this zone depends on many factors; height and load composition, coke quantity in a load. The calculation has been done as the standard methodology of thermal calculation is done; moreover, by using a computer for mathematical models which enables very accurate results. We must emphasize that acquired and used heat in reaction zone and melted materials is calculated in others studies, so their influence in preheating zone is assumed."

Jan 1, 2010

By Hongfa Hu, Stavros A. Argyropoulos

"This paper describes a mathematical model which simulates numerically reaction driven fluid flow phenomena. The driving force of this reaction is an exothermic heat of mixing. In addition, the model predicts the heat and mass transfer phenomena where both heat source and heat sink co-exist in close proximity. The heat source is generated by an exothermic reaction. The heat sink is formed by a moving boundary such as the melting of a solid. This type of phenomena occur quite often in various metal processing operations in which exothermic additions are immersed in liquid metals. The model is based on the SIMPLER algorithm and uses an enthalpy method to predict the fluid flow, temperature, and concentration fields. The results indicate that the exothermic mixing reaction was responsible for an abrupt rise in temperature around the moving boundary. The intensity of this reaction was also found to be responsible for the enhanced convection of fluid and the acceleration of the moving boundary. The modelling results were also verified by experimental work which included velocity and temperature measurements in a low temperature physical model. IntroductionAlloying additions are used extensively in the treatment of liquid metals during metallurgical processes. The alloying additions introduced into liquid metals can be classified into various classes, each of which follows its own route[l]. As a major group, the exothermic additions follow two different steps during their assimilation into liquid metals. In the first step, upon immersion, a metal shell solidifies around such additions, and then melts back. At this point, the second step commences. During this second step, due to the mixing of the addition with a liquid metal, an exothermic reaction occurs, which liberates large amounts of heat, resulting in an enhanced convection in the liquid metal surrounding the addition."

Jan 1, 1994

By Santhanam Ramesh

"The shell (exoskeleton) waste of shellfish such as shrimps and crabs is the raw material in the extraction of chitosan, a polymer. Chitosan has several medicinal values such as reduction in cholesterol, urea and creatine in the blood. It is estimated that about 40000 tonnes of chitosan may be obtained from all chitin yielding invertebrate sources of India and a foreign exchange of 600 million US$ could be earned annually. Awareness has to be created among sea food processors to put up plants to convert shellfish wastes into chitosan. Similarly pharmaceutical industries may use chitosan in the development of new drugs. Types of training and awareness programmes to be organized for entrepreneurs, sea food processors and pharamacists are discussed in this paper.IntroductionIndia earns annually foreign exchange to the tune of 0.8 million US$ by exporting processed marine crustacean shellfish resources such as shrimps, crabs and lobsters (Figure 1) through 300 sea food processing industries. At present, only a small quantity of shell wastes (exoskeleton) generated from the above is utilized as an ingredient in fish feeds and hence much of the wastes are disposed off either as land fill or by direct dumping in sea. These wastes containing primarily chitin could be the major raw material for the production of a proteinaceous byproduct viz. chitosan, a highly valued pharmaceutically important source"

Jan 1, 2008

By S. C. Dhara

The recovery of Platinum Group Elements from various industrial scraps and spent materials in the form of high and low grade, such as, impure metals, matte, catalysts and other ceramic substrates, etc., has .been described by using high pressure reaction method. Nickel, Stainless Steel, Titanium and glass lined reaction vessels? are used in the reaction process. Primarily, the method involves either direct leaching of the substrates from the metal value or dissolving the precious metal from the substrate. Both acids and alkalies are used along with other reagents in the reaction process. The temperature and pressure of the leaching process are the main criteria for the reaction kinetics.

Jan 1, 1989

By P. Louis

Although cobalt is known and used for its hardness and wear resistance, ductile cobalt can be obtained by electrolysis in chloride solutions, under the following conditions : pH : 1.5 - 2, Co++ : 30 - 60 g/l, current density : 100 - 500 A/m2, temperature 40 - 70°C. No explanation was found for the ductility of the deposit under these conditions. Indeed the ductile P (FCC) cobalt and the hydrogen contents in the cobalt deposits are nearly the same as those obtained in a sulfate media, which gives brittle depo¬sits under equivalent electrolysis conditions. Malleable cobalt sheets can be easily obtained under the proposed conditions which could lead to new applications for cobalt.

Jan 1, 1988

By Tiruttani Munikamal, Suresh Sundarraj

"A numerical model of the induction hardening process of steel cranks has been developed and the predicted results of temperature and phase distribution during this solid state phase transformation process are verified with experimental data from the literature. This heat treatment process involves heating the crank to the austenitic temperature range followed by rapid quenching in water to harden the surface of the crank. The model has been developed using ABAQUS, commercial FEA software. The formation of martensite, pearlite, and retained austenite phases are modeled and implemented through a user defined function in ABAQUS. A sensitivity study on the various process parameters affecting the amount of phase distribution has been carried out.IntroductionThe type of surface and sub-surface microstructure as well as the residual stresses that are present in a component after manufacturing, significantly affects it fatigue performance. The wear resistance of the automotive components such as crankshaft, gears, camshaft and bearings depends on the surface hardness. In order to achieve the surface hardness, these steel components are subjected to a type of quench hardening heat treatment process. There are several heat treatment processes available for the industrial application to improve the mechanical properties of the final part. Case hardening using induction heating is one of the widely used industrial techniques for improving the surface microstructure of a steel component. It consists of two stages i.e. induction heating cycle, followed by quenching in a fluid medium (usually water or oil)"

Jan 1, 2012

By B. J. Beaudry

Intermetallic compounds are frequently required in the form of thin sheets for magnetic refrigeration and other applications. Progress has been made in the preparation of thin sheets of brittle gadolinium intermetallic compounds by hot rolling of sheathed billets. The effect of fabrication procedures on the Curie temperature of GdPd and its heat capacity at low temperatures has been studied.

Jan 1, 1989

By Xiaojie Gao, Shufeng Yang, Jingshe Li, Chengsong Liu

In the blast furnace process, the dust entrained in the blast furnace gas enters into the down-comer, flows through the gravity dust separator (to eliminate coarse particles) and then is collected in a bag-house. The powder collected by the baghouse is called bag dust, while both fractions are called blast furnace dust whose main components are C and Fe. The dust also contains small amounts of nonferrous metals such as Zn and Pb, which have some value. Also, due to the small particle size and low density the dust is easily suspended in air and so can endanger human health. Therefore it is necessary to develop a process to both treat the dust to recover the metal values and to dispose of the residue – preferably by recycling to the blast furnace itself via the sinter strand. These objectives will result in good economic, environmental and social benefits [1].

Jan 1, 2014

By D. R. Spink

A partial desulfurization roasting (PDR) technique has been developed for use on zinc concentrates whereby the sulfide sulfur associated with the iron content is selectively removed over a very short residence ?time in the roaster. The resulting PDR product is then leached for the selective removal of the iron. The resulting leach restdite is an upgraded zinc sulfide concentrate which has a very low iron content. The up-graded zinc concentrate can be subjected to a conventional dead roast without formation of deleterious zinc ferrite so that hot acid leaching and jarosite (or other) iron precipitation steps are obviated. Examples are presented for the treatment of three very different types of zinc concentrates.

Jan 1, 1990

By C. W. Vierrether

Mineralogical analysis contributes directly to the selection of applicable beneficiation techniques for a given site. Tentative remediation methods for use on the Sharon Steel tailings in Midvale, Salt lake County, UT, were determined in part by mineralogical characterization. A systematic characterization scheme was employed to identify mineral species, mineral associations, and grain size. This paper presents the mineral content and distribution data collected for site characterization. This data was used to determine areas that were representative of the total tailings at the Sharon Steel site. Although this was the main focus of characterization, other useful information was obtained. The approximate location of "old jig tails" was identified and insight on possible arsenic, mobility through the pile was also obtained from the mineralogical study.

Jan 1, 1991

By F. A. Fasoyinu

The mechanical properties of yellow brass (C85800), high strength yellow brass (C86300), and high manganese brasses (C99700 and C99750) cast in permanent molds have been studied. The tensile properties as well as fracture and impact toughness of these alloys are strongly dependent on the chemical composition. Alloys and/or compositions exhibiting relatively high zinc equivalent often exhibited high ultimate tensile strength and yield strength with significant reduction in ductility (% elongation). In order to achieve optimum properties with a good balance between strength and ductility, a calculation of the zinc equivalent before alloy preparation can be useful.

Jan 1, 1999

By Donna M. Noel

Bacterial strains have been cultivated from solids previously exposed to cyanide that will tolerate 300 ppm sodium cyanide under anaerobic conditions. In selected solid samples, these bacteria have been shown to reduce the level of cyanide from approximately 300 ppm to essentially zero in about 50 days under anaerobic conditions. Various media were investigated, and the nutrients providing maximal growth were ?established .. Degradation of cyanide in sterilized solids was determined for comparison with degradation obtained in bioactive solids. All experiments were conducted at ambient temperature and initial pH of approximately 10.5.

Jan 1, 1991

By Chuanyu Feng

In this paper, a load-based micro-indentation technique suitable for field applications was developed. This technique bears the same theoretical background as traditional load-depth sensing indentation, and does not need any direct measurement of indentation depth or contact area. The removal of this requirement will reduce much of the cost associated with traditional instrumented indentation. To demonstrate the feasibility, a portable indentation system suitable for online material characterization was developed. Design issues of the portable unit were discussed and preliminary results using the portable unit were also presented.

Jan 1, 2009

By Jian Ye

Recycling of aluminum scrap, such as Used Beverage Container (UBC) scrap is steadily increasing. In secondary remelting of such scrap, it is a common practice to use protective molten salt cover. An appropriate salt protects metal from oxidation, promotes coalescence of the suspended metal droplets, and separates clean metal from the oxide contamination. The molten salt also reacts with metal. This causes metal loss and change of resulting metal composition. In this paper, role of molten salt fluxes in melting of UBC scrap is discussed, and selection criteria for molten salt are provided.

Jan 1, 1995

By Georgette Smits

The gun-sprayed refractory lining of electrothermal furnaces used for the manufacture of carbon disulphide from liquid sulphur and charcoal at between 800 and l000°C are severely attacked during the process. A mineralogical study of samples of eroded refractory material disclosed that carbon disulphide had penetrated the lining, causing the precipitation of sulphides and carbon, and the decomposition of mullite, a major constituent of the lining, to corundum and amorphous silica. Calcium, iron, titanium, and chromium are undesirable cations in a refractory that is used in furnaces for the production of carbon disulphide, since they react readily with this substance. A series of tests, in which samples were exposed to different amounts of carbon disulphide for various residence times and at different temperatures, was carried out with eight types of aluminosilicate-based castable and brick refractory materials, to compare their resistance to attack by carbon disulphide. Mineralogical investigation of the test cores showed that castable refractory materials are unsuitable for this type of process because of the presence of calcium aluminates and other impurities in the cement. Of all the refractories that were tested, a mullite brick of low porosity, containing a minimum amount of impurities, appeared to be the most suitable for use in this type of operation.

Jan 1, 1989

By D. N. Collins

A sampling program was conducted in which both spoon and isokinetic sampling techniques were used to collect samples from the reaction shaft. The samples were then characterised by chemical, XRD and mineralogical analysis. Further information was acquired by measuring the oxygen potential and temperature at the bottom of the shaft using disposable probes. Comparison of the results of the two sampling methods showed that the spoon samples were devoid of material less than 25 m. Sulfur analyses on the samples provided information on the extent of reaction, plume shape and recirculation patterns. Disposable probe measurements showed the measurable particle temperatures ranged from 1150 to 1700 °C and that the material falling into the bath had a normalised oxygen potential similar to the slag. These latter measurements combined with the sulphur elimination and mineralogical analyses provided further information on the extent of reaction and enabled the reaction sequence to be ascertained.

Jan 1, 1999

By Ma Shao Xian, Li Dong, Li Zhen Guo

"The new type shaft calciner ( SK-10 Serials) is developed and designed by CADRE itself on the basis of the conventional shaft calciner. The actual application in a number of calcinations plants have proven that they are of very good effect. Calcined coke calcining heated by the shaft calciner has a high quality, lower lost by fire. The shaft calciner needs no additional fuel when it is working. Anode Carbon Plant and calcined coke Plant commonly used the shaft calciner in domestic. The waste heat from the shaft calciner can be recuperated to generate electricity and to make the steam for produce. Exhaust waste heat is recovered by 90% or more. The new type shaft calciner's structure is optimized by computer simulation for fire-wall structure, combustion air to fuel ratio, volatile combustion is fully in use, furnace cooling zone structure, the exhaust smoking structure and calciner heat balance. Furnace structure and production operating parameters has been got the best optimized results. This paper introduces the working principle and characteristics of the shaft calciner - the equipment for calcining of the petroleum coke. It also demonstrates measured process parameters of the new type shaft calciner. Through comparison with the rotary kiln and conventional shaft calciner, it proves its own technical characteristics and advantages: higher capacity, high quality products, provides more energy for power generation, equipment operation and maintenance costs lower.IntroductionChina's petroleum coke market is mainly dominated by the delay raw petroleum coke. Rotary kiln and shaft calciner are the main process equipment for calcined petroleum coke. As the shaft calciner burning less, no external fuel, waste heat utilization is high, long service life, the utilization rate in China is more extensive than the rotary kiln."

Jan 1, 2012

By Robert B. Haagensen

While light optical microscopy has long been employed by the mineral processing industry, there has been a tendency to shy away from its use for all but the most exacting purposes. Despite the usefulness of micros-copy in solving a wide variety of problems, the response to such work is often less than enthusiastic primarily due to time considerations. Microscopical techniques are therefore often relegated to the "ivory tower" and their direct and practical application to everyday problem solving over-looked. The purpose of this paper is to dispel such attitudes and promote a wider use of light microscopy. Several examples are given which point out the indispensib1e nature of optical microscopy as a rapid means of defining and solving problems in mineral processing. The application of other instrumental techniques to augment the information obtained is also discussed, particularly the value of the combined use of the optical microscope and electron probe micro-analyzer.

Jan 1, 1981

By Sun-Hee Cheong

This study sought to produce L(+)-calcium lactate using precipitated calcium carbonate as a starter culture composite of lactic acid bacteria in lactic acid fermentation. Specifically, precipitated calcium carbonate was synthesized by reacting calcium hydroxide with sodium carbonate in the previous study by the authors. Synthetic precipitated calcium carbonate was then used as the calcium source of lactic acid bacteria during the fermentation process. In general, precipitated calcium carbonate has low absorption rate in the human body. On the other hand, calcium lactate has high absorption rate; it is commonly used in food and drug industries as calcium additives in various foods such as cookies, beverages, bread, sauces, powdered milk, and fruit juice. Calcium lactate has two racemates, e.g., L(+)-lactate and D(-)-lactate. In particular, L(+)-lactate is known to be more soluble than D(-)-lactate and generally produced from lactose by homo-fermentative lactic acid bacteria such as Lactococcus spp., Lactobacillus plantarum, Lactobacillus casei, Lactobacillus curvatus, and Pediococcus spp. Thus, the characteristics of the pertinent lactic acid bacteria and optimal condition such as temperature, pH, precipitated calcium carbonate addition rate, and content of fermentation for increasing formation yield and purity were investigated. The findings suggested the possibility of manufacturing L(+)-calcium lactate using precipitated calcium carbonate as a calcium source with high value-added instead of commercial calcium lactate.

Jan 1, 2006

By S. Yabe

The reinforcement of the annual copper production capacity to 330,000 metric tons has been attained at Saganoseki Smelter & Refinery in 1991, which is one of the largest and most efficient custom smelters in the world. Many operational improvements and technology developments have realized the increase of smelting and refining capacity without adding main facilities to the existing process. The blister copper refining and anode casting process is composed of two 400 tonnes anode furnaces and one double-wheeled casting machine with the capacity of 80 tonnes per hour. The great innovations in this process such as the finding of essential issue on the extending of anode-mould life and the development of a new anode-mould casting machine have raised the operation efficiency by 14% Now, the process is producing 38,500 tonnes per month of best quality anode in well- controlled working condition, and anode productivity per worker increased by 52%. The progress in extending anode-mould life, the mechanism of the new anode-mould casting machine and the increase of efficiency in butane reduction, that were the principal parts of many technological improvements, are described in the present paper, including some operation results.

Jan 1, 1993