Search Documents

By Robert Matusewicz

Ausmelt Technology has been applied to the recycling of spent pot liner (SPL) generated from primary alnminum production. The process is centered on the Ausmelt furnace, in which the SPL is converted under high temperature, oxidizing conditions to an HF containing gas stream and inert slag. fluorine is recovered from the SPL as HF gas and is concentrated and used to manufacture AIF) for recycle to the aluminum smelters. Approximately 87% of the fluorine can be recovered and converted to AIF), with the remainder being effectively tied up in the by product slag. Cost projections show that the recycling process will be competitive with other processes for SPL. The production and recycling of AIF) provides available credit that significantly offsets the operating cost of the facility. Ausmelt Technology for recycling of SPL is currently being marketed in North America by Ausmelt Technology Corporation in Denver, Colorado, and in the rest of the world by Ausmelt Limited of Dandenong, Australia.

Jan 1, 1996

By Wenliang Cao, Jidong Li, Mingjie Zhang, Yiyong Wang

In CaC12-CaF 2 System, we studied the electrode process and discharge mechanism of preparation of Al-Ca alloys by fused salt electrolysis with CaO as raw material. The change of back electromotive force after adding CaO was measured by continuous pulse oscillograph method and the discharge process mechanism was also investigated by cyclic voltammetry. The finial results indicate that back electromotive force decreases by 0.6V after CaO of 1 % is added and there was a peak of oxidation current ahead of the potential at which the negative chlorine ions precipitated. According to thermodynamic calculation, it was determined that current peak was caused by the CO2 produced by 0 2 - ionic discharge due to CaO addition.

Jan 1, 2014

By E. Kozeschnik

A new model is presented for the simulation of the evolution of precipitates in a multi-component multi-particle multi-phase environment The mathematical formulation as well as the physical background of the model are briefly introduced and its capabilities are discussed on the example of a precipitation sequence in a complex steel. Keywords: Modeling, precipitation kinetics, nucleation, growth, coarsening

Jan 1, 2003

By Ann M. Hagni

Flash reduction of zinc oxides is an alternative, environmentally safe method to leaching and electrowinning for zinc recovery. Zinc and lead are volatilized in a flash reactor, a non-hazardous residue is generated, and the fuel source is inexpensive coal in the flash reduction process. Results from experimental laboratory tests yielded low zinc recovery for this process. Mineralogical and textural characterization of the residues from the flash reduction tests for different feed materials and temperatures were conducted to determine the cause for the low zinc recovery. Reflected light microscopy, cathodoluminescence microscopy, scanning electron microscopy-energy dispersive spectroscopy, and X-ray diffraction were utilized in this applied mineralogical research. The original zinc calcine is composed primarily of fine-grained, iron-bearing zincite particles, 25-40 um in diameter, in a porous texture. Pellets processed at 1150°C were found to produce reaction rims of franklinite-magnetite-jacobsite solid solution that are 125-200 um thick and surround cores of unreacted iron-bearing zincite in a Zn-Fe-Si-Ca glass matrix. The reaction rims have subsequently oxidized to form an outer 10 ~m thick rim of hematite. Slags from calcines processed at 1275°C are primarily triangular particles with porous centers, cenospheres, and spheres of iron-bearing zincite, in addition to rectangular particles composed of non-porous franklinite-magnetite solid solution cores with iron-bearing zincite rims. Slag particles from calcine processed at 1200°C are predominantly 100-250 ~m triangular-shaped, spheres, and cenospheres containing fine-grained franklinite and franklinite-magnetite solid solution in an iron-bearing zincite matrix. Slag from calcine processed at 1300°C are also predominantly 1 00-250 um triangular-shaped, spheres, and cenospheres but contain coarser-grained iron-bearing zincite. The zincite in the penets and the slags typically contain 10-20% iron. Based upon these mineralogical observations, it is concluded that the significant amounts of iron in the zincite prevent volatilization of the zinc in the flash reduction process.

Jan 1, 1995

By Ann M. Hagni

Electric arc furnace (EAF) dust from the secondary steel industry contains lead, cadmium, and chromium that causes it to be classified as a hazardous waste. Pyrometallurgical treatment of EAF dust is directed at recovering zinc and simultaneously rendering the dust non-hazardous. The mineralogy of the EAF dust is important in determining the occurrence and phase relationships of the zinc, lead, cadmium, and chromium contents. The principle phases in EAF dust as determined by reflected light microscopy, SEM-EDS, and XRD are solid solutions of the iron spinels (franklinite, magnetite, and jacobsite), zincite, hematite, and Ca-Fe-Si glass. Chromium is present in small amounts in solid solution in the spinels. Cyclone sizing of the minus 53 pm particles shows that more than 50% of this size fraction are less than 10 pm in diameter. The <I0 pm particles contain zinc as both franklinite in solid solution with magnetite and jacobsite, and zincite as determined by transmission electron microscopy and XRD. Auger electron spectroscopy did not detect coatings of volatile phases on the surfaces of EAF dust particles.

Jan 1, 1994

By Ligang Zhang, Wen Chen, Xinghua Liu, Jialin Li, Xiaoyin Liu, Zhenhong Liao

A research-scale fluidization and magnetization roasting device was developed to evaluate a processing option that might offset the complexity and high cost of the conventional magnetization roasting process on siderite. In this study, the operating parameters of the fluidization and magnetization roasting device for siderite were evaluated through cold-flow tests and magnetization roasting tests. The reaction mechanism functions of the fluidized roasting process are revealed with kinetic studies.

Jan 1, 2015

By F. Mucciardi

With the increasing trend to continuous smelting and converting, granulation of copper matte is gaining prominence as a means of decoupling the smelting and converting operations. Moreover, granulation is also being seen as a possible avenue to using higher grade oxygen in converters. By feeding cold solid matte, the oxygen concentration can be increased to compensate for the lower enthalpy feed. This leads to a higher grade of SO2 in the off gas and a lower total flow rate. Current granulation technology relies on the cooling of a falling matte film by water jets. This technology while effective has several drawbacks including those related to safety. Noranda and McGill University have developed a new process (patent pending) for solidifying copper matte (or slag). It overcomes many of the negatives of current technology. The system is based on an air cooled twin roll caster. This: new system uses no water and instead incorporates heat pipe technology to transfer the heat from the solidifying matte to the cooling air to produce a thin strip of 1 to 2 mm in thickness. Testing of a prototype unit demonstrated its viability. This paper describes this newly developed, twin roll casting system that is completely waterless. The advantages of this process as well as the findings from several tests are also detailed.

Jan 1, 1999

By Mamoru Kuwabara

A high-power sound which can transmit through any continuous elastic medium with less attenuation, particularly in liquid allows us to externally control the system of concern by using the acoustic radiation force or the cavitation phenomena. These functions may eliminate gravitational and/or atmospheric constraints which are often encountered in conventional operations for producing clean and advanced materials. This paper outlines the recent development in the field of sonoprocessing of materials. Cold model experiments in some vessels have been performed to simulate ultrasonic operations such as inclusion removal from liquid, degassing of melt, emulsification of two liquid phases, solidification processing, and decomposition of chemical species in waste water. High speed visual imaging is carried out for better understanding of the cavitation phenomena as well as the followed microjets during the processing. The radiation force acting on fine suspending objects in a fluid can be utilized for eliminating or rearranging/orienting the objects in the fluid. Acoustically induced cavitation phenomena in liquid can be utilized as an effective dynamic means to control interfacial phenomena as well as micro- and macro-mixing of liquid. Sonochemical and thermal effects in cavitation multi-bubble can be also useful in a waste water treatment.

Jan 1, 2006

By D. Valic

In 1997, 9.2 million tonnes of mined, recoverable copper was produced, of which, 1.8 million tonnes or 19.4% was produced by leaching, solvent extraction and electrowinning. The amount of copper produced by this method grew faster than those attained from concentrate smelting, signifying the growing importance of this low-cost production method. Statistical experimental design, unlike traditional approaches, allows for proper distribution of experiments within the boundaries of factors being studied such that the number of experiments required to develop a sound relationship between the factors and a response is minimized. In the past, very little use has been made of statistical experimental design in copper electrowinning studies. Traditional one- variable-at-a-time approaches are widely employed for this purpose. The present study employs a factorial experimental design to relate current efficiency with current density (180 and 300 A/m2), copper concentration (25 and 65 gL), and temperature (40 and 60 °C). Pure synthetic electrolyte with a constant acid concentration of 180 g/L was used throughout the study. The designed study produced a linear relationship where the independent variables of current density, copper concentration, and temperature, and their interactions, were found statistically significant. It was shown that current efficiency could not solely be used as a predictor of copper cathode quality. The quality of the deposit is difficult to be incorporated into a model or relation. It was determined that other measures, such as cathode morphology and crystal structure should be considered. This was done through XRD and SEM analysis.

Jan 1, 1999

By C. Schwandt

Recent research work has led to the development of a new electrochemical hydrogen sensor, which is based on a proton conducting solid electrolyte in conjunction with a self-contained solid hydrogen reference standard and is operated at elevated temperatures. The incorporation of the internal hydrogen reference renders the sensor versatile and user-friendly and makes it attractive for practical exploitation. The present article focuses on the utilisation of the sensor as the integral part of a probe for the quantitative determination of hydrogen in molten aluminium and aluminium alloys. The main features of the sensor and the probe as well as the measuring technique are discussed. Experimental results obtained with the novel analyser in trials under industrial conditions are presented and highlight the good performance of the device.

Jan 1, 2003

By M. A. Llavona

In Spain, as in many countries, the gold content of jewellery must be officially hallmarked. The official methods of assay are gravimetnc cupellation (a method which is highly accurate but both time and sample consuming), potentiometry, gravimetry and volumetry. In this paper, a procedure for measuring gold by flame atomic absorption in jewellery samples is described. The method is based on the acid digestion of a 40 mg sample. The quantity of aqua regia necessary for dissolving the gold, the ideal weight of a sample in order that the error may be minimal, the effect of the acids employed, the type of material used for its storage, and the necessity of employing a buffer to avoid the ionization of the solution are described. The method proposed is simple, highly accurate and causes little damage to the jewellery.

Jan 1, 1999

By Stephen J. Hales

State-of-the-art Resistance Spot Welding (RSW) equipment has the potential to permit adaptive feedback through recent advances in computerized process control. The initial step toward achieving this goal involves assessment of the effect of specific variables and the interaction between these process inputs on spot weld characteristics. This investigation addresses this issue through the application of Taguchi methodology to understand and refine a RSW schedule developed for joining of two dissimilar aluminum-lithium (AI-Li) alloys of different nominal thickness. The experiment was designed to establish a hierarchy of inputs with respect to each &apos;other, and to determine the significance of these inputs with respect to experimental noise. Valuable insight was gained regarding the interaction between process variables and the effect of certain equipment-related changes. In spite of a decrease in equipment performance, an improvement in the maximum strength attainable for defect-free spot welds resulted from the application of the statistical experiment.

Jan 1, 1992

By C. Lupi

Zinc chloride electrowinning presents difficulties in obtaining smooth, compact and dendrite free deposits with a high current efficiency due to the presence of undesirable metal ions. However, it is hard to define a level of impurities tolerable in zinc deposition, and despite a lot of research in this field, the reaction mechanisms of the undesired metal ions are still not clearly understood. In this study, the influence of Fe, Cd, Co, Ni and Cu additions were investigated, as well as their synergic effect on the zinc electrodeposition process from chloride electrolytes and on the obtained deposit morphology. The tests were all performed in presence of TBACl which reduces the harmful effect of such impurities on the zinc reduction.

Jan 1, 2003

The kinetics of the oxidation of cyanide by manganese dioxide was studied using a rotation disc electrode system. The rate? of the half-cell reaction of cyanide oxidation is increased at higher hydroxide concentrations. An addition of copper up to 0.001 mole/l was found to enhance the diffusion current, especially at a high hydroxide concentration (0. 1M). A similar enhancement of the reaction rate is also achieved with nickel added at levels up to 0.01 mole/l. Manganese dioxide however requires a i:ow pH to achieve reasonable reduction rates. Leaching studies indicated that the initial reaction rate is strongly dependent on pH, initial concentration of cyanide. Using manganese dioxide cyanide could be oxidized at neutral pH&apos;s and ambient temperatures.

Jan 1, 1989

By S. Motoiu

Data acquisition is widely used for controlling flash smelting furnaces. A Romanian smelter from which a large amount of data can be collected uses such a technique. A computer program was developed for interpretation of the data. Inputs to the program are the process data files. Abnormal data are identified using standard statistical techniques; they can be edited if necessary. The following methods can be used for the analysis: linear correlation (single or multiple), polynomial correlation or comparison of two average values. Time variation graphs and histograms can be displayed. The random balance method was used for determination of significant parameters influencing the process performance. Not all process parameters are recorded, and some of them are not even measured. The software can compute some of these parameters such as: air flow rate required and the oxygen content of the gas: exiting the reaction tower. The software was used for the interpretation of a large amount of process data. The analysis showed that the process did not operate properly at some times.

Jan 1, 1999

By F. Michael Hosking

Modeling of a furnace brazing process is described. The computational tools predict the thermal response of loaded hardware in a hydrogen brazing furnace to programmed furnace profiles. Experiments were conducted to validate the model and resolve computational uncertainties. The results from selected furnace simulations and measured thermal events were compared. Critical boundary conditions that affect materials and processing response to the furnace environment were determined. "Global" and local issues (i.e., at the furnace/hardware and joint levels, respectively) are discussed. The ability to accurately simulate and control furnace conditions is examined.

Jan 1, 1998

By Batric Pesic

Adsorption of gold on activated carbon from gold bromide solutions was examined as a function of pH, particle size, carbon amount, initial gold bromide concentration, bromine concentration, temperature, and various cations and anions. pH did not have any effect below pH=6. Above pH=6, pH had dramatically negative effect. The adsorption results satisfied a first reaction order model. The reaction rate constant was proportional to the inverse of carbon particle radius. It was also proportional to the amount of carbon, and independent of initial gold concentration. Temperature had a very little effect at pH=l. At pH=8, the activation energy was a function of the extent of a reaction, increasing with the extent of a reaction. Cu, Fe, Ca, Mg, and Na cations and sulfate, chloride and bromide anions did not have any effect on gold adsorption. Bromine had a very negative effect on gold uptake.

Jan 1, 1991

By Mitsuru Tanahashi

Oxidation removal of boron from molten silicon by injecting oxygen and highly basic CaO-CaF2flux powder has been investigated with special attention to the dynamic behavior of the injected flux particles and gas bubbles. Since oxygen gas is injected into the melt, high oxygen partial pressure is maintained at the flux-O2-Si interface and the removal of boron proceeds under nonequilibrium conditions. By applying this process, boron concentration in metallurgical-grade silicon can be reduced to a single-ppm level. In this paper, the effects of the dynamic behavior of the flux particles injected into the silicon melt and the area of the reaction field (the flux-O2-Siinterface) formed in the vicinity of the flux-gas exit of the injection nozzle on the rate of the boron removal are discussed from the viewpoint of process dynamics. The experimental results clarified that the boron removal rate is affected by the kinetic energy of the flux particles which is determined by the injection conditions, such as the gas-flow rate of oxygen and the size of the flux particles. At higher oxygen gas-flow rates, the injected flux particles are expected to possess a significantly high kinetic energy such that they penetrate the O2-Si interface formed at the nozzle exit, which results in the formation of a new reaction field for boron removal. On the other hand, at lower gas-flow rates, the injected flux particles possess too low kinetic energy to penetrate the interface. In this case where the formation of the reaction field is limited, it is shown experimentally that the rate of the boron removal is constant, independently of the flux injection rate.

Jan 1, 2006

By Manuel Alvarado, David Nemir, Jan Beck

"Thermoelectric generation using special N-doped and P-doped semiconductors is well known as a means for direct heat energy to electrical energy conversion without the need for moving parts. The technology is used today in niche markets for low level electricity production and has been proposed as a scalable means for capturing large scale energy from waste heat streams. The choice of geometry of the thermoelements and conductors is critical to the successful implementation of a waste heat recovery system in order to manage losses due to Joule heating and diffusive heat flows. This paper describes a simulation study to define the performance impact of different aspect ratios for the active thermoelements and the electrical interconnect. The use of a finite element model that incorporates the intercoupled heat and electrical energy flows highlights some of the issues impacting scalability.IntroductionThermoelectric phenomena arise out of the intercoupled electrical and thermal currents in a material. A two-element thermoelectric generator is depicted in Figure 1. It is constructed by connecting an N-type thermoelement and a P-type thermoelement in electrical series, with both elements in thermal parallel between a heat source and a heat sink. The electrical series connection is made by attaching conductors as shown. Ideally, these series connection elements will be both good thermal conductors and good electrical conductors.The two element generator in Figure 1 is disposed between two thermal reservoirs: the heat source, which furnishes heat energy; and the heat sink, which absorbs heat energy. Heat energy flux Q, flows from the heat source to the heat sink, driven by the temperature difference between the source and the sink. As depicted in Figure 1, when a resistive load, R, is attached, electrical current, I, may be extracted from the thermoelectric generator and furnished to the load. The N-type and P-type thermoelements, are the active portions that do the actual conversion of heat energy to electrical energy. Although thermoelements may be built using conductors such as bismuth and antimony, higher efficiency thermoelectrics are built using heavily doped semiconductors. Thermoelectric devices are generally formed by connecting many pairs (couples) of N and P type thermoelements in electrical series and in thermal parallel. A commercially available module having 127 couples (254 elements) is shown in Figure 2."

Jan 1, 2011

By D. J. Wang

Based on the thermodynamic arid kinectic aspects, the vaccum distillation processes for the separation and recovery of metals from wastes are analyzed. As to the separation criteria, The separation coefficient and equilibrium composition relation between vapor phase and liquid phase are the bases of recovery of metals by vacuum distillation, The vaporization rates and condensation mechanisms are also discussed. Some experimental results which deal with metals-containing wastes are described and the performances of a new kind of horizontal vacuum furnace are introduced, which demonstrate that , vacuum distillation may be a prospective technique for circulation and regeneration of some non-ferrous metals from industrial wastes.

Jan 1, 1996