Search Documents

By M. C. Ruiz

In the present study, the size distribution, Fo(v), of organic drops produced in a continuous-mixing vessel has been determined experimentally for various conditions. The organic phase used was a 1: 1 mixture of a salicylaldoxime (LIX 860N-IC) and a ketoxime (LIX 64-IC) in an aliphatic diluent (Escaid 103). The aqueous phase was a copper sulfate solution. The results indicated that an increase in stirring speed, extractant concentration, and pH produced smaller drops. The effect of the stirring speed was the most significant, decreasing the average volume of drops by 57 % for a change from 300 to 400 rpm. On the contrary, an increase in the dispersed phase fraction, copper sulfate concentration, and retention time produced larger drops. Changes in temperature from 23 to 30°C did not affect significantly the drop sizes. In all cases, the experimental drop size distributions could be accurately represented by a lognormal distribution.

Jan 1, 2001

By W. Kasprzak

Modern light metals processing technologies are very complex and involve a diverse set of variables that must be quantitatively evaluated. The most effective way to design new casting processes that deliver specified metallurgical and mechanical properties is to develop a method of simulating the "real-time" process within a test sample of sufficient size. The results can then be analyzed and the required optimizations can be performed. This paper presents a novel method of simulating the industrial casting processes in a laboratory environment using an experimental apparatus based on the principle of high frequency induction heating. The applicability and accuracy of the proposed analytical method is demonstrated, for example, by simulation of the solidification and heat treatment of a test sample composed of two dissimilar materials. The simulation can be used to develop a stress model for an engine block made from an aluminum based alloy with iron cylinder liner inserts.

Jan 1, 2002

By Satu Jyrkönen

A single-particle laminar-flow technique was used to study reactions of sulfidic nickel particles. The studied materials were three natural nickel concentrates and four synthesised nickel mattes. The variables of the experiments were the gas preheating temperature (500 - 1300°C), the composition of the reaction gas (N2 + 0 - 75 vol-% 02) and the ,particle size of the feed. Chemical analysis of the particles was used to determine the oxidation degree of the materials, and optical and scanning electron microscopy were used to detect alteration in their morphology, internal composition and structure. General reactivity of the materials was monitored by the extent of sulfur removal. The reaction mechanism of the studied materials was found to depend primarily on the materials composition as well as oxygen content of the reaction gas.

Jan 1, 1998

By P. Myllykoski, J. Nylander

"A commercial program package called Crownoff for the simulation of temper rolling in four high mills has been verified against measured data. The agreement between measured and calculated transversal strain distributions of the strip was found to be good. Effects of the strip crown and work roll bending force on the strain distribution were simulated. The results showed that when a single ground camber of work rolls is used for all strip widths; the strip crown should be parabolic, excluding the edge drop. An increase or decrease of the strip crown by 30 % during a coil can be compensated by a 2 to 5 t change in the work roll bending force. The ability to control the strip crown by work roll bending was insensitive to strip width. IntroductionCold rolled steel strips are usually temper rolled after recrystallization annealing, which follows cold rolling. The purpose of temper rolling is to suppress the yield point, finish the strip surface and correct possible flatness errors. The presence of a yield point might otherwise cause problems during subsequent forming processes. The in homogenous yielding in non-temper rolled steels leads to the formation of Lüders bands in the strip surface.The rolling force is influenced by the rolling speed and changes in frictional conditions in the roll bite. Therefore it is very important to plan carefully the mill settings and control algorithms during rolling. The purpose of mill control algorithms is to ensure constant reduction and the best possible strip flatness during the entire coil.Correctly predicting the rolling force is important for determining the mill presettings. Torque, forward slip and power requirements are not usually critical, if the reductions are small. However, the large elastic deformations occurring in the roll bite make the physical description of the process difficult. Physical rolling models developed for cold rolling contain assumptions that lose their validity as the reductions decrease to the level of one per cent."

Jan 1, 1994

By C. Burton Clark

The important role of the petrographic microscope in the petrology of refractories is discussed, based on 45 years of industrial experience by the author. Highlights of his career are used to illustrate improvements in equipment and techniques during the period. Two specific investigations are described which emphasize the interrelated use of the petrographic microscope with other instruments such as the x-ray diffractometer and scanning electron microscope. Emphasis is placed on the use of phase equilibrium diagrams for guidance in predicting and interpreting reactions that occur under non-equilibrium conditions in the manufacture and use of refractories.

Jan 1, 1982

By S. J. Gerdemann

The U.S. Bureau of Mines is studying the kinetics of wet oxidation of sphalerite concen- trate (ZnS) as a possible process for a gravity-pressurized reactor (GPR). At tempera- tures in excess of 200' C, a sphalerite water slurry will react with 0, to form zinc sul- fate (ZnSO,). However, the pressure required to keep the water from boiling at these temperatures has kept this reaction from becoming a viable continuous process. The GPR can easily obtain the high pressures required for this reaction. The reaction rate is complicated by the solubility of 0, in water and the further oxidation of ZnSO, to insoluble zinc oxysulfate (Zn4(OH),S04.4H20). The effects of pressure, temperature, and particle size on the rate of reaction were investigated. Reaction rate was found to be limited by the amount of oxygen in solution. However, at 250" C and 1500 psia, over 90 pct of the zinc was solubilized in less than an hour. The conditions for maxi- mizing the Zn++ in solution, while minimizing oxysulfate formation, are discussed.

Jan 1, 1993

By Jong-Ren Tarng, Gin-Hwa Chen, Wen-ku Chang, Ke-Ming Lin, Yuan-Haun Lee

"The majority of early studies used X-ray diffraction, but this requires a model to interpret the diffraction processes. A turbostratic model has been applied by Warren, Franklin and Bacon to a wide range of materials including both soft and hard carbons. Maire and Mering applied the same methods to the interpretation of the (001) lines of a series of graphitic carbons. In our case, graphitic carbons undergone high temperature and high pressure graphitization processes have been evaluated by the same methods. It were found that most technological XRD data were obtained by a Rietveld method with the least-squares refinements could be in the simplest way since the full correction technique is very laborious. The behavior of carbon materials as it proceeds through the graphitization process is characterized by changes in the measured interlayer spacings (d) a~ a function of temperature. A series of graphitic carbons including the transformation of diamond to graphite through the process under high temperature and high pressure have been evaluated. A simple calibration equation has been established. IntroductionRecently, in battery industry, carbon materials are used as cathode in lithium ion batteries. However, graphitization of those carbon materials is concerned as if lithium ion intercalated into those carbon cathode. Both high-graphitization and low-graphitization carbon materials are suitable for this kind of application.As for graphitization, the starling materials from which carbons may be prepared vary extensively from pure chemical compounds, to mixtures containing II wide range of molecular weights, such as pitches. So its graphitizing, perhaps the most notable feature of the process, is the very wide range of temperature over which the perfection increase, unlike the more common transformations of solid state materials which occur in a narrow temperature range. The variables involved in the conversion of the initial hydrocarbon to a carbon residue, which may vary widely in final perfection, are time, temperature, stress and impurity content"

Jan 1, 1996

By R. A. Roberti

Most copper refineries use conventional wheel systems to cast anodes. over a period of time the copper moulds that are used become warped and cracks develop. To control mould warpage, the mould's are either rejected after a certain warpage is reached, or the shape is restored by mechanical means. The cracks, unless they are very severe, are repaired by a peening process. Even with regular maintenance to control warpage and cracks, the moulds have a limited useful life. If warpage and cracks are not controlled, anode quality deteriorates and tankhouse operations are seriously affected. -An intensive study was initiated to develop means of controlling mould warpage which culminated in the d?evelopment of technology to control mould warpage to within ±1. 5 mm, and at the same time effectively contr0l: cracking and significantly increase the mould life-. The warpage control has been achieved by using a unique mould design. Mould cavities are present on both sides of the mould and periodic inverting controls the wa-rpage in the cavities. The mould casting procedure has been developed and all production wheels have been converted to the new mould design. The performance characteristics of these moulds will be detailed. 21

Jan 1, 1987

By J. B. W. Bailey

The Noranda Horne smelter in Quebec, Canada has change considerably during the last two decades to accommodate varying custom concentrate receipts, closure of the Horne mine, better working conditions, environmental programmes, new technology and increased energy and labour costs. This paper highlights the reasons for changing the smelter from two calcine charged and one wet charge reverberatory furnaces fired by coal to a smelter using. tonnage oxygen oil, natural gas and coal in a single wet charged reverberatory furnace and a Noranda Process continuous Reactor. The current operation 1 described, including three major topics; the use of oxygen/fuel burners on the charge banks of the reverberatory furnace which has increase the smelting rate from 680 to 1100 tonnes of concentrate per day; the oxygen enrichment of the Noranda Process converting air to achieve smelting rates of over 1800 tonnes of concentrate per day; the converting of the mixture of 73 percent copper matte produced from the Noranda Process and the 33 percent copper matte produced from the reverberatory furnace.

Jan 1, 1983

By Tatiana Pereira Moreno, Priscilla Aki Mori de Hanashiro, Viviane Tavares de Moraes, Denise Crocce Romano Espinosa, Hugo Hashimoto

"Nowadays, End-of-Life (EoL) Liquid Crystal Displays (LCDs) are traditionally disposed in landfills. The increasing access to LCD technology over the last years by Brazilian consumers has intensified LCD' s disposal as an environmental and economic issue. This study aims to characterize used LCDs to identify the main components for recycling. Characterization was performed through scrap disassembly and its components were identified, separated, and weighted. LCDs were disassembled and the following divisions were applied: screen, metal frame, polymeric frame, polymeric sheets and electronic part. Some techniques were used to determine the concentration of Indium in the LCD, the glass/plastic ratio and the different kinds of polymers that compose the screen. The techniques used for characterization included inductively coupled plasma optical emission spectrometry (ICP-OES), Fourier transform infrared spectroscopy (FTIR) and thermogravimetric analysis (TGA). This method, when applied to a wide range of LCDs, can allow the development or improvement of an EoL management of LCD.IntroductionWaste Electrical Electronic Equipments (WEEEs) are waste from discarded equipment, such as computers, monitors and cellphones [1]. Over the past years, treatment of WEEE has been emphasized. It occurs due to the technology's advancement that leads to an even larger increase of WEEES [2].Among WEEEs, there are the liquid crystal displays (LCD). LCD technology is applied in cell phones, tablets, computers and monitors. Nowadays, it's the most well known technology when it refers to monitors, due to its advantages over the Cathode Ray Tube (CRT) technology. Some of them are energy saving, smaller size and no radiation emission [3].This feature in the LCD's global market along with the speed at which electronic equipment becomes obsolete affects society economically and ambiently.This issue becomes even more serious when considering the final destination of the liquid crystal displays. LCDs are lead to landfills as other WEEEs. Besides the different materials long degradation time, the environment is damaged by the disposal of the potentially reusable and hazardous materials [ 4]."

Jan 1, 2014

By Akram Alfantzai, Farzad Mohammadi, Maysam Mohammadi

"Degradation of lead anodes has always been a major concern among the electrowinning industries. In this study, the effect of agitation of the zinc electrowinning solution on the integrity of lead anodes was investigated. Galvanostatic experiments were performed at 37±0.5°C using 0,600 and l000rpm magnetic stirring rates for 24 hours. The Pb02 layer formed on the anode surface was reduced to PbS04 (discharged). The discharge information was used to calculate the amount of Pb02 present on the surface. Weight loss measurements along with the discharge calculations revealed that the degradation rate of the lead anode increased as the solution was stirred more vigorously. Furthermore, the amount of remaining Pb02 on the surfaces was decreased as a function of solution velocity. Therefore, it may be concluded that, degradation rate oflead anodes is controlled by detachment of the corrosion products from the surface rather than by electrochemical reactions. IntroductionElectrowinning is one of the extraction stages of zinc, in which pure zinc is deposited from acidic solution after froth flotation, roasting and leaching processes. The anode electrode materials play important roles in the electrowinning process. Their electrocatalytical capacities determine the oxygen evolution overpotential, and consequently the cell potential and energy efficiency of the zinc electrodeposition [l]. Purity of the zinc deposited on the cathode is affected by the solubility and corrosion resistance of the anode materials. Using insoluble materials as anode in the electrowinning leads to the higher purity of the deposited metal on the cathode[2]. Lead (Pb) and its alloys have been used as the anode in the zinc electrowinning because of its special properties such as relatively low cost, low melting point, insolubility in solutions containing sulphuric acid and high conductivity in both states of metallic and oxidized [3, 4]. In zinc electrowinnig, zinc reduction occurs on the cathode (reaction 1) and the oxygen evolution reaction (OER) (reaction 2) is the main anodic reaction [5, 6]."

Jan 1, 2013

By Susumu Nagae, Hajime Ikeda

Recently, a number of mine development projects have been setback by social, economic and, environmental circumstances that had not been seen before. Many of these problems do not always originate from direct mine pollution. Typical examples of these are· conflicts between the exploration company and the local residents, sudden objections just before the development is to begin, and unexpected tightening of environmental regulations. The common background to these problems is expanding global environmental awareness. This includes complex factors ·such as the expansion of exploration to remote regions, the brisk activities of environmental NGOs, the increase of international environmental laws and, governmental policy changes. Today, the range of issues concerning mine development is widening significantly. The participation of local residents arid NGOs in the development planning, together with the company and government, has become essential for smoothly carrying out mine projects and making them more beneficial for stakeholders. Introduction The common image of the environmental problem with respect to mining is direct mine pollution, such as the collapse of tailings dams, pollution from refineries, and acid mine drainage. All over the world, the mining industry has made large investments in capital and technology to solve and prevent mine pollution, and these efforts have been making steady achievements. However in recent years, new cypes of environmental problems which are not originating directly from mine pollution are emerging frequently. Most of the problems are concentrated at the exploration stage to early stage of development, which have less impact on the environment. In the worst case, mining project may be forced to cancel and could cause serious damage to the industry because they could not collect their investment. I would like to take a general view of the examples of new types of trouble, their characters, background, and strategies against these problems.

Jan 1, 2000

By Wang Jia, Chai Li-yuan, Zhang Jin-Long, Peng Bing, Zhang Qiang

"Electrolytic manganese dioxide (EMD) residue was mixed with shale and fly ash as the main materials to make solidification/sintering brick for the utilization of the residue from EMD production. The effects of sintering temperature, sintering time, solid waste content and cooling process on its mechanical properties and toxic elements solidification were investigated according to compressive strength and leaching toxicity. The results showed that the calcined residue had capability of solidifying toxic metals and exhibited perfect strength after treated in the optimal parameters of EMD residue below 50%, temperature at 1000-1100°C, time3-5h, and semi-quenched at 600°C1 InstructionSolid clay-brick holds the leading position among building materials for a very long time in China. The traditional technique of making clay-brick has the drawbacks of backward process, simple facilities and single product. Since Chinese Reform and Opening-up, urban-rural construction and real estate have been booming with the rapidly development of national economy and science technology. The problems of ruining fertile land, environment contamination and high energy consumption in the traditional technique of clay-brick making have not been solved yet. On the other hand, more than 7 billion tons of industrial wastes are accumulated over years which occupies over 6.7 million hectares filed and causes serious environmental problems[1-31. Strategy present in ""The Chinese Agenda of the 21st Century"" required the production of wall materials less energy conservation, land saving and waste recycling.Coal gangue[4-9l, fly ash[I0- 13l, sludge from waste water treatment and tailings of gypsum, pyrite, copper mine, high silicon containing iron, asbestos and ects [l4-lSJ are the solid wastes used for brick making around the world. There are two kinds of process for brick making, high temperature sintering and low temperature steam curing[19•201. Although the technology of two brick making made great progress and got widely application in construction field, no precedent for preparing sintering-bricks with EMD residue as materials occurred in China because of its complicated processing technics and lack of sufficient practical experience to guarantee the bricks' quality.In this study, EMD residue was mixed with shale and fly ash as the main materials to make solidification/sintering brick. The effects of sintering temperature, sintering time, solid waste content and cooling process on its mechanical properties and toxic elements solidification were investigated according to compressive strength and leaching toxicity."

Jan 1, 2011

Smelter operating and environmental requirements demand high on-stream time (high reliability) from the primary smelter sulfur retention device - the sulfuric acid plant. The key to reliable smelter sulfuric acid plant operation is the gas cooling and cleaning system. Problems in the gas cleaning system cause corrosion, plugging, equipment failure, etc - plant down time, in the contact section of the plant. The last fifteen years have seen major changes in gas cleaning system design to the current standard of brick lined venturi scrubber, packed gas cooling tower with plate type liquor coolers and lead or plastic tube precipitators. The current-design offers improved impurity scrubbing along with increased reliability. In addition, a number of alternate gas cleaning systems have been offered. Chematics LAB System: Monsanto DuPont Dynawave System; Lurgi venturi scrubber with lead star gas cooler. This paper will review the design and operating advantages, disadvantages, and risk of the standard gas cleaning system and compare it to the alternate systems.

Jan 1, 1992

By A. J. Maselli, E. C. Cemak

Hartford Steel Technologies (HST) has a pyrometallurgical and hydrometaliurgical process capable of reclaiming valuable metals from a hazardous waste· stream such as EAF Dust. The HST Process effectively addresses the growing environmental concerns surrounding the increasing production of EAF Dust without producing any hazardous waste material as byproducts. Currently EAF Dust production levels are exceeding the 1,000,000 metric tons per year mark. The HST Process is designed to separate iron, zinc, lead, cadmium, copper, and silver metals using a two-phased process. The Pyrometallurgical side of the Process utilizes a Rotary Hearth Furnace to separate the iron metal from the remaining metals. These remaining metals are further separated, using a Hydrometallurgical Process, in a series of digestion tanks. The individual metals are then collected in saleable form.

Jan 1, 2000

The physico-chemical principles of chloride hydrometallurgy are reviewed to rationalise the complex chemistry in chloride-based processes for metal sulphides in terms of the predicted Eh-log[Cl-] relationships, measured changes in activity of H+, Mz+, Cl- and solubility of Ag(I), Cu(I), Cu(II), Pb(II), Ni(II), Au(III), Sb(III) and Bi(III). These changes reflect the nature of chemical speciation, competing effect of hydration/hydrolysis and chloro-complexation,composite effect of increasing acid and/or salt concentration and decreasing water activity. Rate data for the dissolution of PbS and ZnS in HCl containing Fe(III) or Cu(II) are compared and contrasted to highlight the effect of acid and chloride concentration, water activity, and the nature of oxidant. It is shown that LiCl, NaCl and HCl influence the kinetics of oxidative PbS leaching based on their effect on solubility of PbCl2 co-precipitated with elemental sulphur on the mineral surface. Evidence for the beneficial effect of Cu(II) in sulphide leaching is discussed.

Jan 1, 2003

By Reinhard Bott

The Companhia Mineira de Metais (Brazil) runs a Zn-recovery plant in Tres Marias, federal state Minas Gerais, Brazil. The Zn-production is about 65,000 t/a, This corresponds to a concentrate throughput of about 255,000 t/a with a Zncontent of about 29.5 % at an output of 85 %, The plant is run continuously 360 d/a and 24 h/d, respectively. From this it can be concluded that: Input: approx. 650 - 700 t/d ore-concentrate and approx. 29 t/h ore-concentrate, respectively.

Jan 1, 1990

By Patricio Ruz, Gabriel Riveros, Carolina Ramirez, Andrzej Warczok, Rober Treimer

"Continuous converting of copper matte produces slag with high cuprous oxide content. The corrosion of chrome-magnesite refractories with slag of high cuprous oxide content is a major problem. Properties of olivine type of slag make the slag very attractive for matte smelting and converting.Analysis of phenomena determining the slag infiltration into the porosity of a refractory and dissolution of refractory components in the slag allowed for better understanding of the mechanisms of refractory destruction.The results of laboratory scale tests of the olivine slag infiltration into open porosity and corrosion showed dominating effects of slag temperature and cuprous oxide content. The optical and X-ray examination of slag samples permitted the definition of the mechanism of formation of new phases and refractory deterioration. 71"

Jan 1, 2009

By Rafael Colás

Computer visualization can be employed in industry as an aid to the understanding of the complex interactions between variables encountered in production. The examples of ingot casting of rimming steel and that of hot rolling of low carbon steel strip are presented. Both processes are mathematically modeled, and their results are presented in a graphical way. Such models have been proven to be an asset in quality improvements and increase of productivity as the personnel involved get a better understanding of their job.

Jan 1, 1993

By Denise Corrêa de Oliveira

Household zinc based batteries, dry and alkaline, has become the most popular sources of electrical energy, and are widely used. Because of their heavy metals content such as mercury, zinc and manganese, spent batteries cannot be directly placed in common landfills without a pretreatment. As a municipal solid waste, these batteries may cause serious health problems and environmental impacts. These damages can be reduced by recovery (which means saving natural sources and energy), recycling and adoption of cleaner technologies. Although this worry has been increasing recently, and producers are doing efforts to reduce the mercury content, batteries still need proper safe disposal conditions or recycling processes. This work presents the efforts in progress to characterize and recycle mixed - dry and alkaline - spent batteries, by using low cost unit operations. Some possible recycling stages and recovery parameters of metals as zinc and manganese are also discussed.

Jan 1, 2001