Search Documents

By Yongqi Sun, Zuotai Zhang

Our study investigated the influence of P2O5 and B2O3 on the viscosity and crystallization behavior of Ti-bearing blast furnace (Ti-BF) slags for the purpose of Ti extraction. The investigation of the crystallization behaviors were carried out using a single hot thermocouple technique (SHTT) and the viscosity was obtained by rotating cylinder method. For the viscosity, the results showed that P2O5 substantially increased the slag viscosity. P2O5 is a network-forming oxide, which increased the degree of polymerization of slags and accordingly increased the slag viscosity. However, both of slag viscosity and apparent activation energy for viscous flow remarkably decreased with B2O3 addition. As a typical network forming oxide, B2O3 was introduced into the network and existed dominantly as 2-D structure, BO3 triangular, which caused a simpler structure and a decreasing slag viscosity. As for the crystallization behaviors of Ti-BF slags, both P2O5 and B2O3 enhanced the crystallization trend of rod-shape rutile and suppressed the crystallization trend of dendrite CaTiO3. Therefore the added P2O5 and B2O3 caused the primary phase change from CaTiO3 to rutile. Additionally, it was found that the rod-shape rutile showed a 1-D growth, whereas the dendrite CaTiO3 showed a 3-D growth style.

Jan 1, 2015

By G. P. Chaudhari, F. Warchomicka, M. Dikovits, V. Pancholi, C. Poletti

"The hot formability of a microalloyed steel with 0.16 wt-%C modified with N is studied by using processing maps. Compression tests of cylindrical samples are carried out using a Gleeble®3800 simulator in the range of temperature between 750 -1000°C and strain rates between 0.01-100 S-1. For this alloy, an Ar3-temperature about 740°C is determined by means of dilatometry. Processing maps are calculated using the modified dynamic material model developed by Murty and Rao for different logarithmic strains. For the instability map, the parameter Kj developed by the authors in previous works is used and compared with other instability values. Softening in the flow curves provoked by induced ferrite during deformation at low temperatures and low strain rates is reflected in the n-value. Light optical microscopy (LOM) and electron back scattered diffraction (EBSD) measurements are used to study the microstructure of the hot deformed samples to determine the deformation mechanisms active and to verify the processing maps.IntroductionProcessing maps offer a good possibility to optimize thermomechanical process parameters and to avoid defects in the products. Prasad et al. [1] developed the processing maps using the dynamic material model (DMM) and Murty & Rao [2] modified it. Processing maps consist of two superimposed maps: the dissipation efficiency and the instability map. The processing maps can be used to detect areas with a good hot formability, which are normally related to restoration of the material by dynamic recovery/recrystallization. For a high dissipation efficiency value and no instabilities, a good hot formability is predicted. In the DMM no storage of energy takes place and so the material is considered essentially dissipative, this is only true for high temperatures and high strain rates [1]."

Jan 1, 2012

By Young-Geun Park

A new decarburization model for the RH system was constructed for calculating the decarburization reaction using a three-dimensional fluid dynamics program. The entire fluid flow in the RH process was calculated by evaluating the shape and volume of the plume zone, formed by Ar gas blown through multiple nozzles on the wall of the snorkel. On the basis of this fluid flow, the decarburizaiton reaction was calculated through establishing the decarburization reaction model, which considers the thermodynamics, reaction kinetics, and the decarburization sites (Ar bubble surface, bath surface, and the CO bubble fomtation at inner sites). The results from this model were compared with a real RH operation results with good agreement. Because it is possible to predict the carbon concentration at various conditions using this model, it may be useful in increasing the decarburizaiton rate. Key words : RH process, plume zone, decarburization, Ar bubble surface, bath surface, inner site, circulation flow rate.

Jan 1, 2001

By D. M. Jones

Dust generation data have been obtained from 19 industrial Outokumpu flash furnaces. Statistical analyses of the data have been carried out and the most significant factors affecting dust generation evaluated. The results indicate that dust production may most effectively be minimized by: 1) Minimizing the distance between the molten slag and the furnace roof 2) Optimizing burner design and combustion parameters.

Jan 1, 1996

By A. D. Damodaran

Batch scale and continuous rotary kiln carbothermic metallisation of ilmenite followed by different down-stream treatments such as catalytic rusting, acidic chloride leaching, oxidation-leaching etc. has given rise to a high grade synthetic rutile (98% TiO2). Rotary reactor metallisation experiments had concurrently given important information with respect to mean residence time, dispersion number, hold-up and axial velocity profiles of the solids bed. A mathematical model based on law of additive reaction times has indicated that Boudouard reaction becomes faster than reduction reaction at higher conversions. A possible use of high grade synthetic rutile in paint industry and metallised ilmenite as welding electrode flux material are discussed.

Jan 1, 1992

By Susumu Okabe, Etsuji Kimura

"The Mitsubishi Continuous Copper Smelting and Converting Process is the typical applications of injection metallurgy to nonferrous metallurgical operation, where the top blowing multiple lance system is employed for the continuous feeding of the raw materials and reaction gases into the molten bath. This results in an effective dispersion of the reactants into a strongly agitated bath. These are considered as the major advantage of the process with respect to the high production efficiency. On the other hand, however, the strong agitation may cause a considerable amount of refractory wear, and the melt splash generated by the lancing may also have negative effects on the productivity, i.e. the increase in the refractory wear, the metal loss, the heat loss, and the accretion growth, etc. Therefore, the optimization of the blowing condition as wen as furnace design is very important to achieve a stable and efficient operation, and fundamental understanding of the injection, agitation, and splashing is badly needed.In this paper, fundamental aspects of the Mitsubishi Process regarding injection, especially splashing phenomena, are discussed. The splashing on a vertical plane caused by the top blowing gas injection onto liquid surface was investigated through physical model study. As a result of the study, the splashing rate on the furnace wan was wen correlated with the physical properties of the bath materials, gas velocity, cavity shape, lance/wall distance and ceiling position. Obtained equations were compiled in a computer program and have been successfully applied to the evaluation of the furnace design. IntroductionInjection metallurgy is an application of gas/solid-in-liquid dispersing operation to the metallurgical processing, and has been widely adopted in various fields in order to improve their efficiency or productivity. The dispersed small particles of gas or solid materials in the liquid phase result in increased interface area, and injected momentum causes an agitation and enhanced heat and materiel transfer. Typical examples of injection metallurgy are LD converter for steel making, PS converter, Noranda process, Isasme1t for copper making, and Mitsubishi Material's continuous copper smelting and converting process, and so on."

Jan 1, 1996

By I. Gaballah

Spent hydrorefining catalysts may contain 4 to 6 % of COO and/or NiO, 8 to 16 % of Moo3 and up to 10 % V205 generally supported by alumina. Raw samples are roasted in order to eliminate carbon, sulfur and hydrocarbons contained in the spent catalysts. The roasting optimum temperature and time are 500 "C and 7 hours. Selective chlorination of roasted samples with Cl2 + air, Cl2 + N2 and Cl2 + CO is investigated in order to recover the valuable metals. Depending on the chlorination it is possible to recover more than 80 % of the Ni and Co about 95 % of the Mo and up to 80 % of vanadium compounds. Cobalt and nickel chlorides are obtained by leaching the chlorination residues' by acidified water. Molybdenum and vanadium chlorides and/or oxychlorides are obtained by selective condensation from the vapor phase. The chlorination of the catalyst support, Al2O3, can be limited to less than about 5 %. Besides the reaction temperature and time, the oxygen partial pressure of the chlorinating gas mixture appears to be the key factor for the reactions' selectivity.

Jan 1, 1993

By Fabiola Alvarez, Ana E. Bote, Daniel Pasquevich

"The oxidation of aluminum and its alloys was extensively studied for improving the corrosion resistance in structural materials having high specific strengths. But this reaction involves the formation of a very thin barrier layer on the metallic pieces. Furthermore, the ·recent development of the directed melt oxidation process for producing metal-ceramic; composites has renewed the interest in the study of interaction between gases and metals. Oxidation experiments in the presence of different chlorine partial pressures and at different temperatures were performed in ·a thermogravimetric balance, and microstructures were analyzed by electronic microscopy and X-ray diffraction. The oxy-chlorination kinetics was determined and the oxide formed W(IS amorphous at temperatures below 600 °C and crystalline .at higher temperatures. The appropriate experimental conditions for the fastest completed oxidation was further determined.IntroductionThe use of fine powders for the manufacture of ceramic components has significant advantages. They include excellent sinterability; low sintering temperature and better microstructure leading to improved mechanical properties. The conventional method of producing fine oxide powders involves controlled precipitation and pirolysis of suitable salts. The main limitation of the high temperature decomposition route is the evolution of environmentally unacceptable and corrosive gases. Controlled precipitation of hydroxides from solutions of salts, followed by thermal treatment involves large volumes of solutions and the calcination step that can induce grain growth (1).Direct oxidation of aluminum metal for producing alumina powder requires high temperatures for the direct oxidation of molten Al alloys by a vapor phase oxidant process (2, 3) or high technological process like thermal plasma reactor ( 4).Oxidation of high purity aluminum (5, 6) below the melting temperature· is initially characterized by a nearly linear reaction rate, followed by a rate which decreases rapidly with further weight gain. However, the oxidation rate of an aluminummagnesium alloy is much faster and it does not conform to any common oxidation law, but it is nearly parabolic at temperatures between 200 and 400 °C, an nearly linear· above 400 °C."

Jan 1, 2000

By H. Y. Sohn

The purpose of this article is to analyze critically and quantitatively the effect of chemical equilibrium on the overall rates of fluid-solid reactions. It is shown through a mathematical analysis that a reaction with a small equilibrium constant (a positive standard free energy of reaction) is more likely to be rate-controlled by pore diffusion or mass transfer than a reaction with a large equilibrium constant. The overall reaction rate of the former also tends to be slow. Furthermore, the apparent activation energy of such a reaction approaches the standard enthalpy of reaction (Mf'), rather than the true activation energy of the chemical reaction. The Law of Additive Reaction Times developed by the author is shown to apply to equilibrium-limited fluid-solid reactions and to be useful in quantitatively analyzing the behavior of such reactions.

Jan 1, 2003

By P. D. Navarro

The behavior and operability of LIX 1104SM extraction was studied at laboratory scale on the Solvent Extraction at Sb3+, from high concentration sulfuric acid. In order to evaluate the reactant batch tests were made at laboratory scale as well for extraction as for re-extraction of Sb3+. Experiences achieved were: extraction kinetics, temperature effects, selectivity tests and re-extraction selectivity. A extraction kinetics was found, reaching equilibrium in 2 min, high selectivity of Sb3+ extraction in front of Cue , existing As5+ co-extraction and Fe3+ At the re-extraction stage, equilibrium was reached in 3 min, getting high Sb3+ re-extraction efficiency with HCl concentrations within 6 and 8 M. A high selectivity was achieved on Sb3+ re-extraction in front of As+5, existing Fe+5 re-extraction.

Jan 1, 1999

By Xun An

Slag from an electric slag cleaning furnace was injected with methane and air mixtures to facilitate the recovery of copper and cobalt. The effects of methane-to-air ratio, gas flow rate and temperature on the reduction and metal separation were investigated. The results showed that over 90 percent copper and up to 60 percent cobalt could be recovered from the slag with a gas utilisation of around 70 percent, as calculated by thermodynamic simulation. Methane-to- air ratio was a major factor affecting the rate of reduction under the present experimental conditions. Further, injection of gaseous reductants greatly enhanced the coalescence and settling of entrained metal droplets. A reduction mechanism is proposed and the factors influencing the coalescence of copper droplets are discussed.

Jan 1, 1998

By Sheng-li Wu, Guo-liang Zhang, Bo Su

One of the major challenges for the Canadian Gen IV Super-Critical Water-cooled Reactor (SCWR) concept is the selection of fuel cladding materials. The Canadian SCWR concept will operate at a core outlet temperature of 625 oC and 25 MPa of pressure with peak cladding temperature reaching as high as 800 oC. Corrosion resistance is an important factor for material selection. Austenitic stainless steels that contain Cr contents greater than 18 wt.% are generally considered to provide adequate corrosion resistance. In this work, the pressure dependence of the corrosion of austenitic stainless steel 310 containing 24 wt% Cr is assessed at 625 C for exposures of 1000 hours to evaluate the suitability of superheated steam as a surrogate for supercritical water at 25 MPa. Transmission Electron Microscopy (TEM) revealed that 310 exposed to different pressure conditions at 625 oC. (i.e., 0.1, 8 and 29 MPa) had generally the same type of the oxide structure, i.e., a Cr-rich oxide with the spinel structure on outer surface adjacent to the water phase. The material exposed at 8 and 29 MPa had a double layer oxide structure, with the outer oxide layer having a much larger grain size, while the samples exposed at 0.1 MPa showed only a single spinel-phase oxide layer. Cr-depleted recrystallized austenite grains were found underneath the spinel phase oxide. The adjacent large-grained austenite substrate had M23C6 carbides in the grain interior. The implications of these results are discussed.

Jan 1, 2015

By H. L. Fraser

A review of the possibilities of performing microchemical analysis in thin sections using a combination of scanning transmission electron microscopy and energy dispersive spectroscopy of x-rays is given. Particular attention is paid to the factors that limit accurate analysis at the highest spatial resolution. As an example of the use of these techniques applied to a potential problem in minerals processing, the identification of iron pyrite and pyrrhotite particles in Illinois, Herrin #6 coal is presented.

Jan 1, 1981

By Mikiya Tanaka

This paper outlines our attempt to establish a recycle process of nickel in the spent baths and waste rinse water of electroless nickel plating plants using solvent extraction and solvent-impregnated support, Solvent extraction studies of nickel from actual spent baths revealed that (i) nickel is efficiently extracted by a hydroxyoxime extractant such as LIX84I at a pH greater than 6 and is readily stripped with sulfuric acid, and (ii) the mixtures of LIX63 and acidic organophosphorus extractants (D2ERP A, PC88A, and Cyanex 272) enhanee the nickel extraction efficiency to a sufficient degree without pH adjustment, but at the same time, reduce the stripping efficiency. The application of acidic organophosphorus extractants to selectively remove impurity metal ions (iron and zinc) from a real spent bath before extracting nickel lead to the finding that PC88A and Cyanex 272 effectively remove iron and zinc without pH adjustment leaving nickel in the raffinate. The removal of nickel from the waste rinse water was also studied. Solvent-impregnated supports with a macroporous resin and oil sorbents made of natural kapok fiber and synthetic fiber as supports were applied using D2EHPA and LIX860 as the extractants. During the batch operation, nickel is removed with a high efficiency without pH adjustment. During the column operation, however, the effective removal is hindered by (i) the dissolution of the nickel-D2EHPA complex into the aqueous phase in the high loading region, and (ii) the slow removal rate of the LIX860-impregnated support.

Jan 1, 2003

By W. H. (Bill) Jay

The destruction of cyanide creates a significant impost on the financial returns of gold mines. These losses increase substantially when ores containing cyanide-soluble copper are treated. Failure to remove or destroy free or WAD cyanide before it is discharged into tailings dams has, on a number of occasions, led to significant fish, bird and animal deaths. Thus, the retention of cyanide within the leach circuit and the recovery or removal of stable metal cyanide complexes needs to become standard practice for all gold mining operations. Furthermore, reducing cyanide purchases will minimise the quantity of cyanide transported to the mine site thereby reducing the opportunity for spillage of this chemical. Many different physical and chemical methods have been investigated for the removal of cyanide from process solutions. All cyanide destruction methods create a financial impost on the economic viability of the gold mine. To reduce these costs, the recycle of cyanide and the economic recovery of the metals solubilised by cyanide is of prime importance. The alternative methods currently in use, or under consideration for the treatment of copper cyanide, entail high reagent costs, produce the recovered metal in a contaminated form and require the safe handling of hydrogen cyanide. These processes will be briefly discussed within this report Environmental and financial benefits are enhanced by recent laboratory and pilot plant studies conducted by Oretek Limited. The Oretek CPC process for the recovery of copper and the recycle of cyanide from copper cyanide-containing solutions does not require pH adjustment to the alkaline cyanide leach conditions. Copper ions are coordinated to a water-soluble and/or an organic soluble polychelating agent under alkaline conditions and the cyanide ions are displaced Membrane separation, or phase separation of the polychelated copper from the cyanide ions enables the cyanide ions to be recycled and the copper to be directly electrowon from the polychelating polymer. The polychelating polymer is then recycled. Ion exchange resins and solvent extraction systems which may be incorporated into the above process will also be discussed in detail.

Jan 1, 1998

By Junzo Hino

Most of the waste that contains a small portion of copper is landfilled. The recycling process of copper from the waste, such as shredder residue, should be developed in order to save mineral resources and prevent environmental pollution. Shredder residue, generated from disposed automobiles and electric appliances, consists of many types of plastics, glasses and metals. The combustion heat of plastics is efficiently used for smelting in the recycling process that consists of melting and reduction. Because the waste contains numerous components the knowledge of the distribution behaviors of the main components is necessary to develop the recycling process. The distribution behaviors in the recycling process are evaluated by using the thermodynamic calculation program, HSC Chemistry. The calculation results are compared with the practical operation data of the recycling process and discussed.

Jan 1, 2003

By Adriana de Aquino Soeiro da Silva, Joao Alves Sampaioa, Luiz Carlos Bertolino, Francisco Manoel Garrido, Marta Eloisa Medeiros

"Brazil has a large agricultural potential and its production success is related to the chemicaland physical soil characteristics. Therefore, the demand in the use of a great quantity offertilizers to compensate the low amount of nutrients in the soil includes about 40% of foodproduction costs. In order to develop economical alternatives to traditional fertilizers, rockswith potential use in agriculture will be studied. In this work the potassium rock, a greensandslate, will be chemically and structurally characterized for the development of a potassiumthermophosphate. This alternative fertilizer will be obtained based on a fusion of a ponderedmixture of potassium, magnesium and phosphate rocks to be applied in the Brazilianagriculture. Preliminary characterization results indicate that the greensand slate presents ahigh percentage of glauconite, quartz and micas.Keywords: Potassium thermophosphate, alternative fertilizers, greensand slate.IntroductionBrazil has a great agricultural potential and its production success is closely related to thesoil's chemical and physical characteristics. However, the country's soils present lownutrients content and high acidity due to weather conditions. Thus, the use of a high amountof fertilizers makes up for the soils' lack of nutrients and accounts for 40% of food productioncosts. Therefore, research on obtaining new alternative fertilizers is a constant worry due tothe increase on food demand [ 1].The lack of raw material for the preparation of NPK fertilizers in Brazil is a concern and theissue of potassium fertilizers a priority. Such a fact is because in 2008 only 608.000 tons ofKCl were produced, corresponding to just 10% of the Brazilian necessity. Thus, the use ofrocks as agricultural nutrients can contribute to reduce the need for industrial fertilizers.This way, the development of a new agricultural raw material originated from a rock thatalready exists in the country's soil is of great importance for the mineral and agriculturalsectors."

Jan 1, 2011

By Michael Zinigrad

The quality of metallic materials depends on their composition and structure and these are determined by various physico-chemical and technological factors. To effectively prepare materials with required composition, structure and properties it is necessary to carry out a research in two parallel directions: Comprehensive analysis of thennodynamics, kineties and mechanisms of the processes taking place at the solid-liquid-gaseous phase interface during welding processes and development of mathematical models of the specific welding technologies. We have developed unique method of mathematical modeling of phase interaction at high temperatures. This method allows us to build models taking into account the thennodynamic characteristics of the processes, the influence of the initial composition and temperature on the equilibrium state of the reactions, the kinetics of heterogeneous processes, the influence of the temperature, composition, hydrodynamic and thennal factors on the velocity of the chemical and diffusion processes. The model can be implemented in the optimization of various technological processes in welding, surfacing, casting as well as in manufacturing of steels and non-ferrous alloys, materials refining, alloying with special additives, removing of non-metallic inclusions.

Jan 1, 2003

"EAF dust is categorized as a hazardous solid waste. EPA approves only two treatment methods: either sending the dust to zinc recycling facility, or stabilizing it first and then disposing it to a specially-lined landfill. Both treatment methods are costly to EAF steelmakers. In order to reduce the cost and even better to make profit from the dust, EAF steelmakers need to find a costeffective technology to separate zinc from EAF dust. This paper is dedicated to discussion of a novel recycling strategy: in-process separation of zinc from EAF dust. The concept of in-process separation of zinc from EAF dust is first defined, and then a simple Zn concentration model is developed. From this model, two approaches of in-process separation of zinc from EAF dust are derived: (1) prematurely capturing dust at very high temperature when zinc is still in vapor status, (2) prematurely collecting dust immediately after quickly cooling EAF off-gas from high temperature to low temperature. Next, thermodynamic analysis is conducted to understand zinc behavior in EAF off-gas. It is demonstrated in theory that zinc is in vapor status while it exits from electric arc furnaces. At last, recycling routes and economics of in-process separation of zinc from EAF dust are discussed.IntroductionElectric arc furnace (EAF) plays an increasingly important role in steel production. According to USGS, steel production from electric arc furnaces has long exceeded that from basic oxygen furnaces [JJ. In 2009, electric arc furnaces produced 64% of total steel in the United States.Along with the fast growth of EAF steel production, generation of EAF dust is also rapidly increasing. A survey by AIM Market Research showed that 10 - 20 kg EAF dust was generated for every ton of EAF steel produced [2] In 1999, the United States alone produced 770,000 metric tons of EAF dust [3] In Europe, annual generation rate of EAF dust is more than one million tons [4-5]. In Japan, about 450,000 tons of EAF dust is produced each year [6] Globally, total generation of EAF dust was estimated to be more than 5 million tons per year [5] EAF dust is categorized as a hazardous solid waste since it often contains heavy metals, such as lead, chromium and cadmium. US Environmental Protection Agency (EPA) approves only two methods for treating EAF dust: (1) recycling the dust by EAF-dust recyclers, and (2) specially landfilling the dust for disposal after it is chemically stabilized. These two methods of treating EAF dust are both very costly to EAF steelmakers. It was estimated that a fee of $150 to $200 per ton of EAF dust was paid for various treatment options, which added approximately $2 - 3 cost for every ton of liquid steel produced by electric arc furnaces [?J."

Jan 1, 2011

By Kirsi M. Riihilahti

The oxidation characteristics of solid copper matte particles under simulated Kennecott-Outokumpu Flash Converting conditions are presented. The effects of feed matte grade, matte particle size, oxygen-to-matte mass ratio, oxygen content of the process gas and temperature on the particle oxidation rate, quality of conversion, particle size change and particle morphology were determined. The converting quality was highest (~68) with the 58% copper matte at 1100°C. At similar conditions, the 72% copper matte was more likely to produce copper oxides and leave unoxidized particles rather than directly produce sulfur dioxide at 1100°C, resulting in an average converting quality of 55. The quality of conversion was poorest for the 72% matte at 920°C (~45); the sulfur removal was extremely low even with a relatively high degree of oxidation. Fragmentation of the particles was significant in all cases with the 72% matte. A higher O2/matte .ratio and higher temperature, in general, resulted in increased fragmentation while oxygen enrichment had no significant effect. With the 58% matte, particle size was found to increase for the finest fractions rather than to decrease due to particle expansion.

Jan 1, 1998