Search Documents

At any given lime, the tidal force subjects massive regions to a spatially uniform load. The deformation of any large structure due to these forces is proportional to the elastic properties of the structure. In this aspect, the tidal force applies a load in a manner similar to that of a large-scale testing machine. Any anomalies in the measured tidal response must reflect alterations in the average elastic response of the massive structure. In the present work, tidal tilt measurements obtained in the wall of a large dam are used to infer changes in the response of the dam to applied loads. In particular, it is found that the dam response has changed by approximately 13 percent, on average, for two monitoring periods separated by 5 years. It is possible that these changes were produced by the different volumes of water in the dam for the monitoring periods. The tidal measurement technique can also be applied to monitor changes in the average structural response of large underground and surface masses relevant to coal and metal mines.

Jan 1, 1992

By Kevin M. Connor, O&apos

An example application is presented in which Time Domain Reflectometry (TDR) was utilized to monitor roof strata movements during pillar extraction in a potash mine. The study was initiated when Western Ag-Minerals decided to implement secondary mining of pillars in order to extend the life of their Nash Draw Mine. A prototype operation was conducted in one mine panel to assess mining equipment and procedures, and to determine if ground control problems would develop. An instrumentation array was installed by personnel from New Mexico Tech and Western Ag to monitor strata movements, changes in pillar stress and surface subsidence, and these data are being analyzed by the Bureau of Mines. This paper is limited to a discussion of roof-floor convergence and roof strata movement to illustrate the application of TDR to ground control. Plots are presented which demonstrate the capability of distinguishing location, magnitude and mode of rock movement using TDR to interrogate coaxial cables grouted into holes drilled in the roof.

Jan 1, 1990

The properties of coal or rock containing gas are very important both for studying coal and methane outburst mechanism and for controlling underground rock in mining. The theological fracture properties of coal containing gas were studied to obtain its rheological fracture principle both in microscopic scale and in macroscopic scale. The application of this principle is successful in explaining coal and methane outburst mechanism and for putting forward a rheological hypothesis of coal and methane outburst.

Jan 1, 1992

By Ross Seedsman

There are many models for how roof bolts behave, one of which is prevention of shear along bedding. The basis of this model is that a roof beam will not delaminate if bedding parallel shear can be prevented. A key point in such a model is that bedding discontinuities are present naturally in the roof and that mining induced stresses do not generate new surfaces. The presence of these discontinuities means that the rock mass must be modelled as a transversely isotropic material if continuum codes are used. A limit-equilibrium type design method for specifying roof bolts is being developed using voussoir beam and excess shear force concepts. The method incorporates much of what operators know intrinsically about roof reinforcement, and allows mining engineers to focus on the key uncertainty - the frequency and location of bedding surfaces in the immediate roof. Areas where more research is required are highlighted.

Jan 1, 2000

By Binchuan Zhang

The combined reinforcement system (CRS) combines the strengths of roof' bolting, resin-anchored cable bolt, and chemical grouting to effectively control the deformation of the strata surrounding an extremely poor entry. It is easy to implement and fast in installation. It is one of the systems that are suitable for the reinforcement and maintenance of extremely poor entries.

Jan 1, 2001

By Ezzeddin Bakhtavar

There are several geotechnical challenges and risks inherent in the interaction between the open-pit and block cave mining environments. This is especially true when they have to work simultaneously for a short time, as well as when only the caving operation is continued. Some of these challenges and risks include the induced zones of stress due to the large and deep open-pit, instability of the slope, instability of the crown pillar and water inflows, subsidence, and sometimes instability of the main accesses to the block cave portion of the mine. These challenges usually occur due to cave propagation. In this paper, these geotechnical challenges and associated risks have been studied and discussed. It was concluded that the majority of the mentioned geotechnical risks could be decreased, and often eliminated, by considering the appropriate dimensions of a stable crown pillar, especially in simultaneously working open-pit and block caving operations.

Jan 1, 2011

By Kikuo Matsui

In a difficult economic environment, the coal mines in Japan have been making extensive efforts in order to survive by rationalizing the mining operations. Introduction of a new longwall mining system is one of these efforts to establish the rational production structure. In the high production longwall mining system, gateroads should be developed rapidly and maintained effectively during their lifetime. Strata bolting support system has been employed in the gateroads to raise their stability levels and reduce their maintenance cost. However, excessive gatemad closure caused by longwall mining is still occurring, impeding the passage of equipment, personnel transportation, and ventilation air in the longwall panels. This paper describes the development system of gateroads and proposes a new mining method to control the excessive roadway closure problem.

Jan 1, 1995

By Hani Mitri

A new monitoring device called SAFEBOLT (Stress And Force Evaluator in Bolts) has been recently developed. The device SAFEBOLT, essentially replaces the load cell, it permits the monitoring of bolt axial load from the time of its installation underground. The SAFEBOLT system consists of a portable readout unit, connecting cable and the SAFEBOLT device, which is installed in the bolt head. SAFEBOLT can be installed on any industry standard rockbolt. No special installation method is required; the conventional method of bolt installation by the stoper or roofbolter remains unchanged. The device is completely encapsulated in the bolt head, which makes it resistant to corrosion, rugged, and free of any electrical wires. Pilot tests at three underground Quebec mines were carried out and helped improve the initial design of the device connector. The paper reports on two of such pilot tests.

Jan 1, 2001

By Tim Ross

Slurry injection into mined-out panels is an attractive alternative for disposal of coal preparation plant fines. however, in areas where surface subsidence cannot be tolerated, either by law or necessity to protect surface structures or aquifers, special consideration trust he given to the effect of slurry injection on panel stability. Slurry injection can lead to panel failure and unplanned subsidence by degrading roof, pillar, and floor strength. Water degradation is of particular concern where clay is present in the floor. Recently. unplanned subsidence related to slurry injection occurred at an Indiana room-and-pillar coal mine subject to weak floor conditions. This paper discusses the efforts of the mine operator to determine the causes of the panel failure and to design panels and injection procedures to allow for future economic slurry injection without subsidence. The numerical and empirical/analytical techniques applied give the operator a rational approach to pillar panel design for future injection panels under various cover depths and weak floor conditions.

Jan 1, 1998

By Buddhima Indraratna

The paper highlights the conceptual developments in rock mechanics applied to quantify the effect of bolts in the stabilization of joints and yielding soft rocks.

Jan 1, 1992

By Paul A. Lu

This paper proposes an unconventional, simple, and practical method of measuring mining-induced around stresses with hydraulic borehole pressure cells. The method is a direct ground stress measuring technique. It does not require the value of deformation modulus for back-calculation of stresses; instead, it directly measures the ground stress in situ. The applicability and practicality of the technique are shown by two case studies. The technique may be applied to monitoring a stress build-up that may lead to mine roof failure or to rock and coal outbursts.

Jan 1, 1984

By Alan Campoli

The Eclipse System was developed by Minova USA Inc. formerly Fosroc Inc. to improve the performance of 5/8-inch deformed rebar fully grouted into a one inch borehole. An 1/8-inch offset bolt head combined with specially formulated Eclipse Lokset resin cartridge results in reduced gloving and increased mixing efficiency. The benefits of the Eclipse System have been demonstrated, under the supervision of MSHA, in Kentucky, West Virginia and Illinois coal mines in partnership with Excel Mining Systems, a leading roof bolt manufacturer. Over 100,000 units have been installed to date. Eclipse system bolts exposed during overcast construction at the Panther Mine of Cumberland Resources displayed an extremely well mixed, uniform resin anchorage over the entire bolt length.

Jan 1, 2003

By Graham Daws

State of the Art Room and Pillar mining techniques have been employed at two coal mines in the UK in the last two years. This paper describes the design of pillars and rockbolted support systems for Room and Pillar mining operations in these collieres. Within the last year, rock mass classification systems have been used in the design process of a room and pillar mining layout at one of these collieries. In particular, the roofbolt support system was detailed using these techniques and the support system was linked with operational aspects such as depth of cut. The depth of cut was initially estimated using rock mass classification systems and then verified by a stand up trial which was monitored remotely. The stand up time has a direct influence on the operational aspects of the mine and this is described. The design was verified by performance monitoring and the results are discussed. The importance of understanding the role of rockbolting is emphasised along with some examples of accurately determining in-situ bolt performance. The paper also recommends some modifications to rock mass classification systems when applied to underground coal mining operations.

Jan 1, 1998

By Leigh J. Wardle

Significant coal reserves in New South Wales lie under areas with steep topography such as valley slopes and cliffs. Subsidence predictions are difficult to make for these locations as existing empirical databases cannot cover all permutations of topography and mining geometry. Two dimensional numerical model alternatives are of limited applicability. Consequently a novel three-dimensional numerical model is developed including the detailed panel layout, realistic rock mass properties including the full stratigraphy, goat behaviour and actual surface topography. Model results show the same trends as subsidence measurements from Baal Bone Colliery in the Western Coalfield of New South Wales

Jan 1, 1992

By John Feddock

This study deals with underground mines and ground control and the prediction of seats strength characteristics based upon ultrasonic logging. Exploration drill holes, both rotary and core holes are used for proving coal reserves and determining mining parameters. Drill hole cores can be subjected to geologic study and geotechnical evaluation. In addition, the use of geophysical logging techniques is well established in determining certain strata characteristics and ground parameters. Since the characterization of the rock mass in mines remains insufficient in most cases, the idea of possibly characterizing the strength parameters without expensive core retrieval and laboratory testing is very attractive. The elastic properties of the rock can be deduced from measurement of the sonic velocity if the density is known. Through the use of in-hole geophysical density logging combined with an ultrasonic logging tool, the estimation of strata properties is possible. An investigation was conducted at two Indiana underground coal mines using geologic logging, geophysical logging, ultrasonic logging and laboratory strength testing to establish the strength properties of the roof rock. A specialized ultrasonic logging tool with one transmitter and two receivers enables nearly continuous readings along the length of the hole. The results of correlating portions of the data are presented. It is anticipated that the ultrasonic logging will be a supplemental tool for extending laterally the strata characteristics obtained from the existing program to surrounding areas. This may be obtained from the relatively inexpensive logging data obtained by ultrasonic logging.

Jan 1, 2003

By Duk-Won Park

A vast majority of the operating longwall sections use shield-type face supports to provide ground control in the United States. As a co-operative research program between the University of Alabama (UA) and Jim Walter Resources, Inc.(JWR), a joint research program is underway to study interaction of shields with surrounding rock masses. A series of analyses on the response of shields are performed using monitored data at a longwall face in a deep coal mine. In this paper, various effects of parameters, such as leg pressure, setting load, developing load, maximum loading rate, pressure in capsule, and convergence between canopy and base, are discussed and recommended as stability indices. A microcomputer program is being developed for instantaneous interpretation of the shield monitored data, and for giving warnings of potential problems. The preliminary results define the effects of the setting load, developing load, and rate of developing load or leg closure rate. The objective of the study is to understand the shield characteristics and their interaction with surrounding strata in real time, then develop a reliable program for maintaining longwall stability.

Jan 1, 1992

By Clifford McCartney

The PropsetterTM System has been designed and developed to cost effectively solve problems experienced with conventional underground supports used in tailgates, headgates, bleeder entries and as supplemental supports. The PropsetterTM System utilizes the strength and orthotropic properties of timber to achieve initial stiffness and controlled yield as the roof and floor converge. Utilizing a prestressing system developed in South Africa by our parent company, the PropsetterTM prestresses/preloads the roof and floor on installation. The PropsetterTM System consists of five integrated elements which are easily assembled to achieve the objectives of ? Improved support. ? Improved safety, ? Reduced cost, ? Reduced material handling, ? Improved installation productivity, and ? Improved ventilation.

Jan 1, 1995

By John Stankus

Regional high horizontal stress has long been recognized as an important factor affecting roof stability However, localized high horizontal stress, although causing many ground control problems, has not received due attention, Through many ground control studies and underground experiences, it has been round that localized horizontal stress can be created by abrupt changes of overburden and stream valleys. The magnitude of localized horizontal stress depends on the valley configuration and overburden depth. Utilizing the Jennmar Finite Element Analysis System (JFEA), this paper analyzes the mechanism of the localized horizontal stress concentration based on two cast studies.

Jan 1, 1999

By Winton J. Gale

Coal mine pillar design formulae available to mine planners are typically based on relationships determined for specific site conditions. Application of these methods is difficult when other factors, relating to mining or geological conditions, not specifically addressed in these relationships are encountered. A review of pillar design methods, coal strength properties and relevant field monitoring of pillar behaviour has shown pillar strength and deformational characteristics are extremely sensitive to in situ behaviour of the rock and other material components that make up the coal pillar system. A method has been developed that has been found to provide excellent correlation between existing field data using the strength and deformational characteristics of materials determined in selected laboratory tests. This method is based on definition of the leading conditions, accurate modelling of the strength, confining conditions and deformation occuring in the roof, floor and coal seam and definition of the in situ strength of coal based on underground monitoring of appropriately sized coal pillar. The design method is considered to provide an accurate and rigorous pillar design method that will give mine planners a more rational mine design capability which is based on the mine geometry and geological setting of the operation. It is envisaged that availability of such a method will allow significant optimisation of pillar layouts and more closely define the geological and mining issues that relate to pillar design optimisation.

Jan 1, 1992

By Daniel S. Mazzei

This paper will be a general discussion of surface flooding considerations as they affect mining facilities site selection, based primarily on experience with several such problems with which MSHA's Bruceton Technical Support staff has been involved. The detailed analytical procedures used in arriving at engineering solutions of these problems will not he presented here; the emphasis is on drawing attention to this additional aspect of mine design which hitherto has been largely overlooked due to insufficient awareness, information and criteria. The paper's purpose is to stimulate thought and offer guidance concerning the selection of sites for mining facilities in light of the potential for flooding problems caused by surface waters. Flooding by surface waters, would generally not be a serious consideration in areas of relatively low topographical relief, i.e. flat lands, although there are exceptions to this rule, for example, in Western areas where flash flooding is a major concern. Therefore, this discussion will mainly apply to areas where the severity of surface flooding would be amplified by the topography-large, well defined watersheds of considerable relief, i.e. mountainous areas. In these regions, steep valley walls cause any rainfall to flow quickly into the relatively narrow valley bottoms. These valley bottoms provide little flow area during storm conditions, so deep and rapidly flowing streams result.

Jan 1, 1982