Search Documents

By Estban M. Domic

The modem copper industry presents an excellent opportunity for the application of clean, environmentally friendly techniques using currently available hydrometallurgical technologies. This paper briefly reviews key events in the development of modern hydrometallurgy in Chile. Discussion is given to those prominent events whose impact continues to be felt on most projects currently underway. Mention is also made of the foundations of heap leaching technologies, preceded by agglomeration and acid curing, known as the T.L. Leaching Process, the cornerstone of more recent developments. A review is also presented of the leading copper hydrometallurgy projects of the 1990s. A list of those projects, their tonnages and the estimated date of implementation is provided. The conclusion provides an overview of developments in research and the trends in the implementation of copper hydrometallurgy projects in Chile for the coming years.

Jan 1, 1998

By R. A. Pond

Two 6.17 m (20 ft 3 in.) diameter raises, concrete-lined to 5.49 m (18 ft) inside diameter, were completed in 1978 at the Monterey Coal Company Number One Mine near Carlinville, Illinois, by Frontier-Kemper Constructors. These two raises are the largest in cross-section yet completed by full-face upreaming, and the success of this project is expected to increase the application of raise-boring to coal mine shaft construction. WHY 6.17 M (20 FT) DIAMETER ? Raise boring is well accepted in the metal mining industry for a variety of applications, and is gaining in acceptance in the civil works construction industry. The use of raise boring to construct vertical openings for coal mines has not been as widely accepted, even though coal mining requires, per mine, the greatest number of openings to the surface of any underground activity. Several factors have influenced the low utilization of raise boring in coal mining: 1. Coal mine shafts must often be of large diameter to pass the required high volumes of ventilation air at acceptably low water gage pressures. Cross-sectional areas of finished shafts exceeding 23.23 sq m (250 sq ft) are common. 2. The life of ventilation shafts is comparatively long, and the typical sedimentary strata overlying coal seams normally require that the shafts be lined. Shafts on the intake ventilation circuit must have permanent water-tight linings. 3. Unconsolidated overburden at the surface is often thick, and as reaming cannot be safely utilized in unconsolidated material,

Jan 1, 1979

By James W. Martin, Robert R. Faddick

INTRODUCTION Virtually every sector of society in our country feels the impact of tunnels, either through the transportation of water, commodities, or people. The economic implications are staggering. The Committee on Rapid Excavation (1) reported that during the near future, 1968-1975, underground excavation activity will comprise 946 miles of tunnels (subways: 85 miles; underground urban highways: 123 miles; intercity highway tunnels: 210 miles; water supply tunnels: 528 miles) and 5,119 million tons of crude ore; metals: 874 million tons; nonmetals: 899 million tons; and coal: 3,346 million tons. It is estimated that the cumulative demand for underground excavation in the decade 1970-1979 will be 13 billion dollars for construction-oriented demand and 16 billion dollars for mining-oriented demand. The respective figures for the decade 1980-1989 are estimated at 22 billion dollars and 18 billion dollars. Of the many advantages claimed for tunnels (2, 3, 4, 5) the environmental considerations are becoming increasingly important. Transportation tunnels particularly for rapid transit systems, offer reductions in noise pollution and air pollution while improving aesthetics and optimizing land use (fewer problems of right-of-way and disruption of utilities). Considerable interest has been shown recently in sub-surface construction and mining (6, 7, 8). Recognizing the future demands for tunnels has led to considerable study of methods to improve rates of tunnel advance per day, safety, and the overall economics. The search for higher rates of advance has Led away from what has heap termed conventional methods (drilling

Jan 1, 1974

By J. S. McAlpine, J. Matousek, W. Muir, P. Downey, K. Major

The Golden Bear refractory gold ore roasting operation is located at Huddy Lake, in northwestern British Columbia, about BO km northwest of Telegraph Creek (see Figure 1). The mine access road, used for supplies delivery, was developed by Golden Bear and consists of a radio controlled 155 km gravel road originating at Highway 114. Hine operations are based on a two week in, two week out rotating shift schedule with personnel transport by chartered aircraft from Vancouver, Whitehorse or the 3 Talthan conmunities. The site runway Is located adjacent to the tailings impoundment.

Jan 1, 1992

By Richard Ladyman, Ken Baxter, G. B. Siddall

The IPS process, developed by Baxter and McAuley, was first applied in Australia in 1984 at Browns Creek in NSW where a small 300kg batch plant was in operation for a number of years. To date a further 14 plants have been installed. While a number of engineering companies have engineered applications of the technology, a majority of the plants constructed to date have been constructed by Como Engineers who have a reference list of 9 installations with batch capacities up to 3.0 t.

Jan 1, 1996

By D. Tao

More than 80 million metric tons of fly ash is produced annually in the U.S. as coal combustion by-product. Fly ash can be converted to value-added products if unburned carbon is reduced to less than 2.5%. However, most of fly ash is currently landfilled as waste due to lack of efficient purification technologies to separate unburned carbon from fly ash. A rotary triboelectrostatic separator has been developed and patented recently at the University of Kentucky with unique features. Several fly ash samples have been used to understand the effects of major process parameters on the separation performance. The results show that compared to existing triboelectrostatic separators, the rotary triboelectrostatic separator has significant advantages in particle charging efficiency, solids throughput, separation efficiency, applicable particle size range. Key words: Coal, Combustion Waste; Fly Ash; Particle charging; Separation.

Jan 1, 2008

By A. Exikis

Simulating a ventilation network of an underground mine can help in solving complex ventilation systems with many features, selecting proper fan specifications, location and settings. Early computer systems running simple network simulations were able to provide solutions to the most common and immediate problems regarding underground mine airflow. The more advanced systems available today can perform more sophisticated modeling and simulation of a mine?s ventilation network and present their results in a more understandable and easy to communicate form. This paper presents a ventilation network case study from an underground mine. All aspects of mine ventilation network modeling and simulation are discussed as well as the results from the simulation process. The algorithms and techniques used are thoroughly explained. Some useful guidelines for the application of ventilation network software are also provided in the text.

Jan 1, 2006

By Dennis P. Bryan

Natural lightweight aggregate may be defined as inherently low density natural mineral materials. In most all instances they are relatively young volcanic rocks which, because of their geologic environment, are limited to the Western U.S. These Tertiary and Quaternary volcanics are low-density glass and vesicular material including, but not limited to, pumice and volcanic cinder. The distribution is widespread throughout the West with the principal producers being New Mexico, California, Oregon, Idaho and Arizona. The primary user is the construction industry where weight reduction equates to cost savings. Principal products in which natural lightweight aggregate is utilized because of its lower density include lightweight portland cement concrete and lightweight concrete masonry units. In addition, due to location, some natural lightweights compete with normal weight constructions aggregates for uses such as road base and common backfill material.

Jan 1, 1989

By R. Asamoah, K. B. Owusu, G. Abaka-Wood, W. Skinner

The hostile nature of industrial autogenous (AG)/semi-autogenous (SAG) mill operation necessitates the need for robust and reliable online measurements. Mill slurry density is regarded as a critical variable and requires a suitable range for grinding efficiency. In this work, mill acoustic sensing of five different slurry densities (50, 60, 70, 80 and 90 wt.% solids) was investigated using a laboratory-based AG/SAG mill. The results showed that slurry density of 70-80 wt.% solids gave the highest mass of -75μm particles and similar acoustic intensity. The mill acoustical level increased continuously coupled with energy reduction as a function of increasing slurry density, an indication of potential realtime measurement.

Mar 2, 2022

By R. Q. Honaker, D. Tao, D. Taulbee, B. K. Parekh

A significant amount of energy exists in the waste generated by the coal and timber industries. In the coal industry, the energy loss is mainly due to the discharge of fine coal to the waste impoundment. Despite the fact that the fine coal has the greatest cleaning potential, dewatering, handling and transportation concerns prevent its use as product in many cases. Likewise, the sawdust generated from wood production has energy value and is used as industrial boiler fuel when the transportation distance is relative short. However, wood waste is often discarded into cumbersome landfills due to uneconomical transportation alternatives. Recent research found that these two waste materials can be combined to provide a high energy fuel of around 13000 btu/lb that can be easily handled and transported to end users.

Jan 1, 2004

By K. R. Weller, U. J. Sterns, P. S. B. Stewart

Complex sulphide ores usually require very fine grinding of the whole ore stream to achieve adequate liberation. Recent improvements to DSM screens have made this device appear competitive with cyclones in circuits treating these ores. A DSM screen and cyclones were tested in pilot-scale grinding of a copper, lead, zinc ore and the resultant data were used to establish a multi-component simulation model. The model was used to assess the influences of mill environment, circuit flows and pulp densities, final product properties (size, relative size and SG of the values, and liberation characteristics) and a second grinding circuit on capacity and product size distributions, and hence define conditions for which one device is better than the other.

Jan 1, 1992

By Jakub Nalaskowski, Vamsi K. Paruchuri, Marcin Niewiadomski, Jan D. Miller

Spherical oxide particles can be used as mineral fillers, paint pigments, polishing materials and catalysts. They can be prepared using various techniques involving precipitation and spray drying. Melting of particles in a high-temperature flame is a simple technique which produces particles with a high degree of sphericity and high smoothness from non-spherical feed material. In current research the preparation of alumina particles by melting the feed material in a hydrogen- oxygen flame is described. The spherical particles obtained were characterized using scanning electron microscopy, atomic force microscopy, energy dispersive spectroscopy, X-ray difiaction, Fourier transform infrared spectroscopy and electrokinetic measurements. The particles pre- pared exhibit a high degree of sphericity and a low level of roughness. The chemical composition of the material after preparation is unchanged, however the crystallographic structure is different. It is suggested that alumina changes from pure a-alumina to a mixture of different transitional forms. Changes in the electrokinetic behavior were also observed for alumina which can be attributed to the strong dehydration of the oxide surface and/or change in the crystallographic structure. Also, the possible accommodation of trace amount of impurities in the surface zone during melting cannot be ignored.

Jan 1, 2003

By J. A. Herbst, Z. Rogovin, Lo. Y. C., K. Rajamani

Knowledge of the amount of time material spends in a continuous mill in a closed grinding circuit is essential for circuit performance analysis and scale-up design. A convenient method for acquiring this information involves the use of pulse tracers in residence time distribution (RTD) experiments. In typical grinding circuit experiments, RTD measurements are done by injecting a pulse tracer into the mill inlet and detecting it in the circuit exit. In this article, an easy mathematical method for calculating mean residence time and the degree of mixing of material in a mill present in a closed grinding circuit is developed. There are no restrictions on the location of the tracer injection or detection points with this method. Any convenient location in the circuit can be chosen without affecting the residence time distribution measured. The analysis of impulse response data obtained from several commercial grinding circuits using this method is presented.

Jan 1, 1988

By S. Ubaldini

Acid mine drainage (AMD) is a common problem in different areas with a past history of mining activities, which is characterized by low pH (2-4.5) and significant toxic metals concentration. The main aim of the present work was to perform a process feasibility analysis in order to remove heavy metals (Cd, Zn, Ni, Mn, Cu) from AMD (Acid Mine Drainage) in a relatively cheap and environmentally friendly way, by means of electrowinning and biosorption. A first characterization of an Italian AMD sample was performed evidencing a zinc concentration around 2 g/L, cadmium and nickel content of about 4 mg/L, manganese of 85 mg/L and iron 190 mg/L. Electrowinning tests lead to the following metal removal after three hours treatment: Zn 99%, Ni 99.9%, Cd 99.9%, Cu 99%, Mn 87%, Fe 96%. Moreover, an high grade of purity of the metal deposit has been achieved (Zn>95%), as observed by X-ray diffraction analysis. Considering that metals concentration in the effluent was still above legal limits (in particular for Zn, Mn and Fe), a further biosorption treatment was planned in order to produce an effluent fitting environmental limits. Experimental electrowinning tests and literature multimetal column biosorption data have been used in order to perform a preliminary techno-economic feasibility analysis of the process aimed at metal removal from AMD. A treatment cost of about 6.5 ?/m3 AMD has been estimated, for a plant capacity of 10 m3/h AMD inlet flow rate.

Jan 1, 2006

By Mark L. Bricker

The Jim Bridger Coal Mine, operated by Bridger Coal Co., is located in Sweetwater County, WY about 56 km (35 miles) northeast of Rock Springs. Bridger Coal is a joint ven¬ture between Nerco Coal Corp, the operator, and Idaho Energy Resources Co. The permit boundary encompasses more than 81 km'- (20,000 acres) on the western side of the Continental Divide. Since the mine began opera¬tions in 1974, it has produced about 82 Mt (90 million st) of coal while moving about 344 hm3 (450 million cu yd) of virgin earth. Annual production averages 4.5 Mt to 6.4 Mt (5 million to 7 million st) of run-of-mine coal. Coal is consumed on-site by the Jim Bridger Power Plant, a 2000-MW generating station. Electricity is transmitted to the Pacific Northwest power grid that includes Oregon, Idaho and northern California. Geology The mine is located on the northeast flank of the Rock Springs uplift. This is a broad, asymmetrical anticlinal feature about 97 km (60 miles) long and 56 km (35 miles) wide with a north-trending axis. This uplift separates the Green River Basin to the west and the Great Divide and Washakie Basins to the east. Precambrian rocks on the apex of the uplift are estimated to be 5200 m (17,000 ft) above the Precambrian rocks in the Green River and Washakie Basins. Normal faults with generally less than 30-m (100-ft) vertical displacement cut through the uplift. The dip of strata on the flanks is generally between 3° and 15°.

Jan 1, 1991

By G. S. Adisoma, J. J. K. Daemen, R. O. Roko

A common assumption in determining the shear strength of a rock joint using a direct shear test is that the surfaces undergoing relative shear are in complete contact. Furthermore, the limiting displacement associated with the residual strength values is obtained based on engineering judgement through visual inspection of shear force versus displacement curves. This study proposes a systematic way of determining the residual shear strength of rock joints by evaluating the limiting displacement leading to a minimum cohesive strength value and taking the true area of contact into account. The results of the study indicate that there is a limiting displacement associated with the residual shear strength, and some rocks may have an inherent interface residual cohesive strength different from zero. When the cohesion is different from zero, the residual shear strength is likely to be underestimated if the true area of contact is not considered. In the case where zero calculated cohesion is obtained, the area of contact has no bearing on the shear strength equation because the frictional force depends only on the normal load.

Jan 1, 1986

By R. Vance, C. Cho, N. Mardi, Z. Qian, K. Prisbrey

One problem with the application of neural networks to the multivariable control of mineral and extractive processes is determining whether and how to use them. The objective of this investigation was to compare neural network control to more conventional strategies and to determine if there are any advantages in using neural network control in terms of set-point tracking, rise time, settling time, disturbance rejection and other criteria. The procedure involved developing neural network controllers using both historical plant data and simulation models. Various control patterns were tried, including both inverse and direct neural network plant models. These were compared to state space controllers that are, by nature, linear. For grinding and leaching circuits, a nonlinear neural network-based model predictive control strategy was superior to a state space-based linear quadratic gaussian controller. The investigation pointed out the importance of incorporating state space into neural networks by making them recurrent, i.e., feeding certain output state variables into input nodes in the neural network. It was concluded that neural network controllers can have better disturbance rejection, set-point tracking, rise time, settling time and lower set-point overshoot, and it was also concluded that neural network controllers can be more reliable and easy to implement in complex, multivariable plants.

Jan 1, 1998

By T. Leftwich, G. Faison, K. Pavlich, R. Borden, S. Pavlou

Recent regulatory and policy initiatives under the Resource Conservation and Recovery Act (RCRA), and the Comprehensive Environmental Response Compensation and Liability Act (CERCLA), will have a significant effect in risk reduction requirements for the mining and minerals processing industry. For example, Congress is considering regulating 20 special wastes from the processing of ore and minerals through RCRA Subtitle D and TSCA. The performance of risk analyses and environmental planning at mining projects is often driven by Federal and state regulatory standards. Recent regulatory and policy initiatives by the Environmental Protection Agency under the Resource Conservation and Recovery Act (RCRA), and the Comprehensive Environmental Response Compensation and Liability Act (CERCLA), will have a significant effect on environmental planning and risk reduction programs for mining and minerals processing. Regulatory programs implemented under other Federal laws including the Safe Drinking Water Act, Clean Water Act, and Clean Air Act will also impact industry practices. This paper provides: 1) a brief overview of mining waste and mining waste management, and 2) a description of these regulatory initiatives and a discussion on the impacts of new requirements on environmental and risk reduction programs in the mining industry.

Jan 1, 1992

By R. S. Farinato

Thionocarbamate flotation reagents have enjoyed a niche position in the recovery of copper sulfides and activated sphalerites since their introduction in the mid 1950's (Harris, 1954). Thionocarbamates containing an allyl group (-CH2- CH=CH2), introduced recently Lewellyn, 1985; Nagaraj, 1988; Avotins, 1991), are used commercially as collectors for copper sulfides and activated sphalerite. Laboratory flotation tests and plant usage have demonstrated that allyl-containing thionocarbamate collectors exhibit certain unique properties that distinguish them from the corresponding dialkyl thionocarbamates. Spectroscopic (FTIR, XPS) and wettability studies of N-allyl iso-butyl thionocarbamate (AIBTC) and its saturated analog N-propyl iso-butyl thionocarbamate (NPIBTC) adsorbed on copper at pH 9 were performed in order to investigate whether there were any fundamental reasons for these differences. Flotation tests were carried out on chalcocite, copper ore and an activated sphalerite.

Jan 1, 1993

By K. A. Brame, L. G. Austin, R. S. C. Rogers

The breakage parameters of phosphate ore were determined by batch first-ordering grinding studies in a laboratory ball mill according to the Austin, Klimpel, and Luckie procedures. The results were scaled to five larger mills of 0.56, 0.82, 8.36, 4.41, and 5 m in diameter assuming equilibrium ball charges for the full-scale mills. The results were used to predict product size distributions and capacities for batch grinding in the smaller mills and open-circuit grinding in the larger mills. The predicted capacities were in approximate agreement with experimental values except for the 5-m diam mill. The Bond method gave capacity predictions that were 4570 to 150% too high.

Jan 1, 1987