Search Documents

By E. D. Thompson, Y. J. Zhang, K. F. Unrug

This paper presents the results of a recent study on the development of an in situ testing method for determining coal strength in mine pillars. The strength testing is performed in the horizontal holes drilled into the coal rib using a penetrometer, which is an hydraulically powered device that uses an indenter to press on the surface of the borehole until the load reaches the failure point of the coal. The pressure and the penetration of the loading pin are recorded by a data-acquisition unit. The results collected from several coal mines indicate that this testing method is ideally suited for the realistic coal strength measurements. The new testing system not only improves the accuracy of the pillar-strength determination, but it is more cost efficient than the conventional method.

Jan 1, 1997

By A. Casuge, D. Lee, J. A. Finch, C. C. Sui

The adsorption of copper and lead und their subsequent xanthate uptake were compared at pH 3.0, 6.0 and 9.2 on both fresh and oxidized sphalerite. The extent of adsorption and the rate of adsorption were strongly dependent on pH, with the highest adsorption of Cu and Pb being at pH 9.2. In the presence of both Cu and Pb, Cu adsorption was enhanced and Pb adsorption was suppressed. The adsorption kinetics of Cu and Pb were characterized by two- and three-stage adsorption processes, respectively. The exchange ratio of Cu to Zn was about one and that of Ph to Zn was greater than one and varied with pH. The uptake of xarlthate on "activated" sphalerite was dependent on pH. The rnaximum uptake was found to be at pH 6.0 for Cu-activated sphalerite artd at pH 9.2 for Pb-activated sphalerite. A measure of "activation strength" based on inetal ion adsorption and xanthate uptake was introduced. The activation strength of Cu to Pb was about one at acidic pH, but it was higher at neutral (pH -6) and alkaline (pH -3) conditions. The oxidation of sphalerite decreased Pb and, especially, Cu adsorption and decreased xanthate uptake.

Jan 1, 2000

By D. D. Banerjee, S. K. Kawatra, T. C. Eisele

To reduce their sulfur emissions, many coal-fired electric power plants use wet flue-gas scrubbers. These scrubbers convert sulfur oxides into solid sulfate and sulfite sludge, which must then be disposed of. This sludge is a result of reacting limestone with sulfur dioxide to precipitate calcium sulfite and calcium sulfate. The majority of the sludge is simply landfilled, but with increasing landfillimg costs this can cost the plant millions of dollars per year. As a result, this option is rapidly becoming less attractive. Producing marketable materials from the sludge is a far more promising avenue, provided that the products can meet the necessary specifications at a reasonable cost. In this paper, a method is described for using froth flotation and water-only cyclones to remove unreacted limestone from scrubber sludge. The water-only cyclone was found to be very effective for removing the coarser unreacted limestone, grinding ball chips, gravel, and similar coarse impurities. Froth flotation was found to remove fine unreacted limestone, with a minimum of reagent addition.

Jan 1, 1995

By P. L. Padgett, J. C. Hower

Five coals blended at a Midwestern United States power station were subjected to detailed analysis of their Hardgrove grindability. The coals, representing four distinct coal beds, are a low-sulfur, high-volatile A bituminous Upper Elkhorn No. 3 coal (Pike County, Kentucky); a medium-sulfur, high-volatile A bituminous Pittsburgh coal (southwestern Pennsylvania); a low-sulfur, subbituminous coal from the northern Powder River Basin (Montana); and two low-sulfur, subbituminous Wyodak coals from two different mines located in the eastern Powder River Basin (Campbell County, Wyoming). All samples that were processed in the Hardgrove grindability tests were also analyzed for their maceral and microlithotype content. The high-vitrinite Pittsburgh coal and the relatively petrographically complex Upper Elkhorn No. 3 coal exhibited different grindability behavior. The petrographic compositions of the Pittsburgh raw feed, the 16 x 30-mesh fraction (HG! test fraction) and the -30-mesh fraction (HGI test reject) are similar, suggesting that the HGI test fraction typifies the whole feed. The eastern Kentucky test sample is not as representative of the whole feed, with the HGI test fraction having lower vitrinite amounts than the rejected -30-mesh fraction. The Powder River Basin coals are high in vitrinite content and show behavior similar to the Pittsburgh coal.

Jan 1, 1998

Those who have had an occasion to apply geostatistics to the estimation of ore reserves are familiar with the conventional approaches of estimating average grade of quality values for arrays of regular grid squares or blocks. Further, the technology to perform geostatistical analysis and prediction for irregular two-dimensional areas has been available in a practical, readily useable form for some time. However, the generalization of this technology into three dimensions has been hampered by lack of a suitable geometrical characterization for realistic, three dimensional shapes and volumes. The extension of these estimation techniques into three dimensions has now been made possible by a successful integration of the volume modelling capabilities of 3D Component Modelling with proven 3D Geostatistical Techniques. The result is a powerful new technique for mineral ore reserves estimation in a practical, useable form. The technique allows direct geostatistical estimation of grade and quality values for precisely defined, irregular, realistic, geological, and mining shapes or volumes. This paper describes the two technologies, their integration and their application in practice to the estimation of mineral ore reserves. The paper closes with a discussion of the benefits provided by the new approach, in terms of accuracy, efficiency and practicality.

Jan 1, 1991

By J. H. Gasper

The overall success of steep slope (>20°) contour mining is dependent upon many factors. The major factor is the selection of the mining method that best suits the premining site conditions both environmentally and economically. These conditions can be divided into three major categories: 1) Geometric Conditions --machine limitations, slope stability restrictions, erosion capacity, among others; 2) Physical Conditions--material properties, rock strengths, diggability, driving surfaces, among others; 3) Chemical Conditions --acid/base relationships, blending or selective placement of overburden, among others. This paper incorporates these conditions through conceptually modeling compliance oriented contour mining methods; in particular Haulback methods, utilizing: 1) the Front-End Loader (FEL)/Truck; 2) Tractor Scrapers; and 3) Combined FEL-Truck/Scraper. Engineering analyses including machine selection, sequencing, ease of varying production rates, slope requirements (for stability and running surfaces), drainage requirements and many others can be performed after the geometric constraints dictated by in-situ conditions and regulatory requirements have been conceptualized. Once all generalized geometries have been established, reduction to idealized three-dimensional views is achieved. These are then reduced to two-dimensional symbolic models, mainly plan views, but also elevations and sections. Equipment activities and operations are then conveniently overlayed. Without this simple two-dimensional reduction, technology transfer remains awkward and non-analytical.

Jan 1, 1991

By P. G. Semple, K. W. Major, R. M. Nendick

As free milling oxide gold ore reserves are depleted, more mining companies are having to evaluate the available alternatives for treating refractory deposits. The selection of a treatment process can be very difficult; and, despite the claims of their respective proponents, there is no one process that will continuously prove superior. Selection of the optimum process for an individual deposit is contingent on the size of the deposit, the grade of the deposit and the refractory nature of the ore. Since extensive metallurgical test programs are usually required to determine the optimum extraction process, an inappropriate initial selection may prove costly and time consuming. This paper discusses the steps involved in evaluating a refractory ore in order to expedite the evaluation of the required process through the feasibility study stage.

Jan 1, 1990

By T. P. Smirnoff, R. J. Redmond, K .. N. Murthy

To minimize disruption to the Hollywood District of Los Angeles, a mined station using the New Austrian Tunneling Method (NATM) was developed. This paper presents the key factors contributing to the settlements and dynamic behavior of the unique binocular station design.

Jan 1, 1993

By J. W. Leonard

Since the interpolation of exploratory data 1 can be no better than sampling procedures, a series of field experiments were conducted in an effort to determine whether hand-cut channel or core washability determinations best represent continuous miner produced run of mine coal. By obtaining a core drilled to within a few feet of channels taken from an underground face and then overmining both locations; core, channels and run-of-mine coal allocations were obtained from a common sample and all allocations were subjected to identical washability determinations. In order to compare results, basic rules2,3 previously anticipated and later published by the writer were employed. The first rule states that "For any full seam washability determination, the sulfur versus ash function for increasing cumulative specific gravity float coal fractions is linear". The second rule states that "For any full seam washability determination, the recovery versus ash function for increasing cumulative specific gravity float coal fractions is logarithmic".

Jan 1, 1988

By M. J. Rex, K. L. Wiley, D. S. Ramey

In situ leaching, initiated in 1986 at the San Manuel Mine, was economically developed in 1989. The primary reason for this lag time between startup and viable production was the time required for technical development. The technical development pursued comprised detailed design, development and implementation of in situ well construction methods, formulation of suitable well pattern arrays and the development of extensive hydrogeologic and geochemical knowledge of the mineral deposit. Since 1989, the in situ leaching program has become a viable and cost-effective method to extract copper from the supergene mineralized zone of the San Manuel deposit. The in situ leaching methods that are currently used have been progressively expanded and continually developed. They will become the cornerstone of copper production from the San Manuel oxide mineral deposit. This paper presents an overview of the supergene hydrogeology, current design techniques, drilling methods and well completion, pump determination and setting, solution management and future plans for the increased extraction of copper by in situ leaching methods at the San Manuel Mine.

Jan 1, 1995

By K. S. Shivakumar, R. Bhima Rao, M. R. Patil

Liberation size can be estimated using various techniques such as grain counting, frequency curves, X-ray intensity and the mesh of grind. The present investigation deals with the estimation of the liberation size of graphite flake contained in a schistose ore from Shivaganga, India. It was observed that the flakes are liberated at from 75 to 150µm. The rougher flotation concentrate obtained after grinding the run-of-mine ore for 5 min contained 54% fixed carbon. This represented the first stage of liberation. After regrinding to <90 µm in the presence of sodium silicate and guar gum, a cleaner concentrate containing 82% fixed carbon was obtained.

Jan 1, 1998

By D. Malhotra

Metallurgists are continuously striving to improve recovery. But optimization of profits and/or revenue dictates that recovery can be sacrificed at the expense of throughput. However, recently there has been significant interest in the concept of retreatment of tailings to enhance recovery and hence revenue while maintaining high throughput. The authors discuss the technical and economic factors that need to be considered in evaluation of the feasibility of retreatment of tailings including the potential feed streams (i.e., rougher tailings, cleaner tailings, etc.) and processing options (i.e., physical beneficiation, chemical processing, etc.). A case study for base metals is discussed.

Jan 1, 1994

By David A. Summers

In May 1975 the U. S. Bureau of Mines contracted with the University of Missouri-Rolla, Rock Mechanics and Explosives Research Center to develop a Hydrominer modification to a long-wall shearer unit, wherein the rotating pick-laced drums and connecting gear drives are replaced by a water jet cutting head.1 The concept of the water jet cutting head is based on using the high localized energy of the water jets to isolate a slice of coal by cutting a slot under, at the back of, and at the top of the web. The plow blade of the head then advances into the cut and wedges the pillar over onto the conveyor (Figure 1). There were several potential advantages foreseen for the system of which perhaps the most significant were the elimination of coal dust from the working area2 and the ability, with a variation in nozzle geometry, to cut webs of greater depth with a small increase in equipment horsepower. The University initially designed the head, based on experiments carried out in the laboratory, under an earlier Bureau of mines contract. The experiments showed that it was more advantageous to work at a pressure of 10,000 psi with an estimated flow rate of 50 gpm than go to the higher pressures and lower flow rates which have been advocated elsewhere.

Jan 1, 1977

By E. A. Twichell

An entirely new concept in the effective utilization of magnetic, energy has resulted in a major break-through in the design of magnetic separation equipment. One of the first applications of this concept has resulted in the development of a Permanent Magnetic Wet Drum Separator with strength .and operating characteristics equal to Electro Wet Drum Separators. Prior to this development when strength and adjustability were required, electro wet drums were specified even with all their drawbacks. The electros, by nature, are subject to coil failure or burnout, over-heating and loss of strength, high power consumption and generally high maintenance. Now the high strength and the adjustability, formerly the exclusive property of electros, has been engineered into permanent wet drum separators. These units combine maximum field strength in the separation zone with strength adjustment to suit changing conditions. Adjustment can be effected while the drum is in operation without stopping either the feed or the drum.

Jan 1, 1967

By Y. K. Yen, J. D. Miller, C. L. Lin

A PC image-based, on-line coarse particle size analysis system is being developed for the control of crushing and grinding circuits. Initial results had indicated that the system is accurate when tested with irregularly shaped particles which are stationary and do not overlap with each other. Now the system has been successfully tested in the dynamic mode with a moving belt conveyor. On-line size analysis for actual plant operations is discussed and includes: (1) the video system with respect to lighting and data acquisition requirements for a rapidly moving belt and, (2) image sampling, specifically the number of observations needed for accurate sampling and the total time required to perform the calculations for a representative data set.

Jan 1, 1993

By Kunio Hashimoto

The conventional troughed belt conveyor system is the most widely used form of equipment for transporting bulk materials in the world today. The reason is not only because it is possible to transport a great deal over a long distance when compare to other types of equipment but also due to its greater economic efficiency and low initial and running costs. When dry, powdery materials and liquid materials are being conveyed, there are enclosed transport methods such as flow, case, air-slider and pipe line. In addition to features of the belt conveyor, a system employing a pipe line to transport dry powdery and liquid materials has always been considered an ideal method. This has been brought into reality through the Pipe Conveyor Sys tem.

Jan 1, 1984

By Scott F. Andersen

Discussion to include location and description of the project from upper lake through powerhouse to lower lake, noting locations and size of shafts. Discuss evolution of shaft development concepts in conjunction with owner, contractor and CAL OSHA. Discuss elevator shaft equipment, T1 gate shaft, T2 surge shaft equipment, T3 surge shaft and the incline shaft equipment. Question and answer period.

Jan 1, 1981

By Shiou-Chuan Sun

This paper is to be presented at the Annual Meeting of the American Institute of Mining, Metallurgical and Petroleum Engineers, New York, New York, February 18-22, 1962. Permission is hereby given to publish with appropriate acknowledgments, excerpts or summaries not to exceed one-fourth of the entire text of the paper. Permission to print in more extended form subsequent to publication by the Institute must be obtained from the Secretary of the Institute. If and when this paper is published by the Institute, it may embody certain changes made by agreement between the Technical Publications Committee and the author, so that the form in which it appears here is not necessarily that in which it may be published later.

Jan 1, 1962

By F. D. Wang

This paper presents an innovative mining method with the application of the water jet. The basic principle of this mining method is to mine a thin panel slice with a water jet system and to allow the roof to deflect elastically and subsequently to be supported by the coal floor without artificial roof support. Through the sequential mining of layers from top to bottom, the entire seam is extracted and the roof rests upon the mine floor. The advantages of this method are that the safety of underground operation can be greatly increased and the surface overburden disturbance will be markedly reduced. . An economic evaluation of such a system is presented for the total cost estimated per ton of coal mined at the face. This evaluation is then compared to that of a continuous mining section utilizing a room and pillar mining method.

Jan 1, 1991

By C. J. Myers, D. L. McKinnon, A. A. Dasys

In 1988, the National Institute of Occupational Health and Safety (NIOSH) published an information bulletin stating that whole diesel exhaust should be considered a probable carcinogen. Since then, regulations across Canada and the United States (Mine Safety and Health Administration, MSHA) have looked at appropriate exposure limits for underground mine workers. In Canada, an interim standard of 1.5 mg/m3 Respirable Combustible Dust (RCD) has been adopted by some provinces and is being looked at by others. MSHA is considering levels as low as 0.5 mg/m3 soot. Golden Giant, being aware of regulatory developments, decided to look at means of reducing diesel particulate on thier large production machinery. This machinery (LHDs and haulage trucks) is powered by Detroit Diesel 71N Series engines and is used to produce 3000 tonnes of ore/day with a longhole mining technique. Having looked at the various control technologies, it was decided to evaluate the potential of using diesel particulate filters with a copper-based fuel additive for regeneration (the process by which collected particulate is burned off). This paper outlines the control technology used and the results of the field evaluation indicating the benefits to the underground mine worker.

Jan 1, 1993