Search Documents

By J. W. Markham, M. Atiemo, K. Yoshida

INTRODUCTION In open-pit mining of high grade ores, operators of mining equipment in a pressurized cab are protected from inhaling radioactive aerosols by the use of filtered air through a pre-impactor and a HEPA (high efficiency particulate air) filter. At present, a limited amount of scientific information is available on the worker exposure to airborne alpha emitters in the mining of high-grade ores. (Miller, 1977, Nielson, et al, 1979). Factors affecting the worker exposure to alpha radiation are: the grade of uranium containing ores, the environmental conditions inside the mine pit, the protection factor of the cab filter system, the workers' attitude towards the hazards of radioactivity and the adopted contamination control in the cabs. Four series of field samplings were conducted during the fall of 1980 and the summer of 1981 at a mining site in northern Saskatchewan to investigate the extent of protection an equipment operator has against cab internal exposure to airborne alpha emitters with short and long half-life radionuclides. The variation in the breathing zone concentrationnof aerosols as a result of resuspension is discussed, however no attempt was made to isolate and investigate the factors and the associated parameters of the aerosol resuspension phenomenon. AEROSOL RESUSPENSION IN A CAB Mechanisms of Resuspension [Sources]: The presence of radioactive aerosols inside a cab and in the breathing zone of an operator may be due to initial concentration inside [(CO)], concentration in the filtered (HEPA) air (CC, at the flow rate [QC]), the concentration of the aerosol through resuspension ([CR]), the aerosol concentration in the air outside the cab ([CE]) and the concentration of the aerosol in the leaking air [(CL)], at the flow rate of [(QL)]. [Volumetric Equilibrium]: Assuming a uniform concentration of the aerosol in the cab, the aerosol concentration in the breathing zone[ (CBZ)] may be expressed as, [CBZ+CO+CC+CR-CL] If [QC] remains greater than [QL], there is pressurization in the cab. There is particle loss as a result of the leaking air from the tight cab, however the condition of adequate pressurization ensures that [CL ~ CC]. Also for dust particles filtered through HEPA [CC – 0] thus [CBZ + CO + CR] For the radioactive gases, [CBZ - CO + CC] Over long periods,[ CBZ – CE] but if [CBZ] exceeds the value of CE then the aerosol build-up in the cab has, occurred. [Resuspension]: Turbulent bursts are generated within the core region of a cab confinement, such that the down sweeps and the up sweeps of the air bursts cause resuspension of dust from the surfaces. Particles initiate resuspension by four major modes: namely, sliding, rocking, rolling, bouncing or sudden ejection or by combinations of these. Nevertheless the adhesion force between the particles and the surface must be overcome by ejection forces before ejection takes place (Kline et al, 1967, Corino and Bradkey 1969, Kim et al 1971). The phenomenon of particle resuspension from a surface may be expressed in a generalized form as: CR =f (Uz . R . D . H) where CR = Rate of particle resuspension UZ = Surface shear velocity R = Surface roughness parameter D = Aerodynamic diameter of particle H = Frequency of surface airburst A detailed discussion of the individual parameters was attempted for the case of farm tractor cabs by Atiemo (1981), such a treatment is out of the scope of this study. Only the effects of the properties of surface roughness will be discussed. Effect of Surface Properties The roughness of the surface from which dust particles are ejected plays a significant role in the deposition and resuspension of the dust. The roughness or the amount of protrusions greatly influence the intensity of air turbulence in the immediate vicinity of the surface (Schmel 1976). For most roughened surfaces therefore, larger particles may be dislodged in greater quantities than smaller particles. The deposition and the resuspension of dust particles from different surface materials of glass, cloth, metal and rubber have been studied in a wind tunnel (Atiemo, 1981). Field Conditions Mining equipments used are: a backhoe, a bulldozer with ripper attachment and two dumptrucks for high-grade ore operations; a payloader and two dumptrucks for waste handling; and a jumbo drill which drills dynamite holes for ore blasting. All this

Jan 1, 1981

By Don Cchultz

The United States Forest Service, as a land managing agency, is responsible for the surface administration of National Forest lands. The basic objectives of management are protection and utilization of renewable resources such as water, forage, timber, wildlife, recreation, and clean air. Much of the National Forest land in this country is open to mineral prospecting and development. When large de-posits of minerals are extracted from the forest environment, especially by surface methods, there are oftentimes conflicts between accepted mining methods and the objectives of other resource management goals. Such is the situation in Southeast Idaho where several members of the phosphate industry are operating on and adjacent to the Caribou National Forest. In 1966, the phosphate industry and the Caribou National Forest became mutually concerned with the problems of rehabilitating mined areas and minimizing potential damage to adjacent forest areas. A Cooperative Administrative Study was initiated with industry supporting the Forest Service financially and with equipment, material, and manpower, as well as interest and enthusiasm. The objectives of the study are to provide basic, applicable information pertinent to: 1. Protecting the quality of water emanating from mined water-sheds. 2. Providing for soil stabilization on mined areas. 3. Returning mined areas to surface resource production. 4. The feasibility of making mined areas esthetically acceptable. It was concluded that the following separate--yet intergrated--fields should be studied in order to obtain the desired information:

Jan 1, 1971

By P. Otto, G. Borm, Th. Dickmann, F. Amberg, R. Giese

Based on many years experience, the well approved Tunnel Seismic Prediction System (TSP) has been substantially enhanced for online geological prognosis in underground construction. The method provides high resolution seismic images of the rock mass ahead of a tunnel face via an array of standard anchor rods. These contain3D-geophones and can routinely be installed during the excavation process. A further outstanding feature of the system is the newly developed high frequency repetitive seismic source which can easily be fixed at a tunnel boring machine. A user-friendly software package enables online data acquisition, processing, 3D-visualization, and interpretation.

Jan 1, 2001

By W. Trask

The state of the art in crawler transporters for loads to 3 kt (3300 st) is sufficiently advanced to allow compilation of job cost figures showing the economics of tracked vehicle use under a wide variety of circumstances. Initial costs, cost per ton of capacity, and operational and maintenance expenses are presented. Data is derived from participation by the Neil F. Lampson Co. in more than 3 Mt - km (2.05 million st - mile) of crawler operation during the past 16 years. The effects of economics on future design trends will be examined with particular reference to versatility, portability, and capacity.

Jan 1, 1987

By B. Catalano, D. Ifrim

The Annacis Island Outfall Project includes two TBM bored tunnels with face pressures above 3.5 bar, with an internal diameter of 4.2 metres. This paper discusses the innovative approach to TBM tunnelling and TBM design at the Annacis Outfall Project. The TBM custom design includes a 3.6 m OD core machine manufactured by Herrenknecht and a 5.0 m add-on by the Contractor (Bessac), acting as an extension kit, with optimized gantry design to accommodate for short tunnel drives and quicker launches. This novel design approach produced safety improvement, cost and schedule savings while streamlining logistics of TBM retrieval.

Dec 1, 2022

By K. Hiroto, H. Tamamoto, G. J. Kusuma

"Acid mine drainage (AMD) has become a serious environmental problem in the mining industry in the last decade. Many efforts have been made in an attempt to find a better method to manage this problem in a proper manner, both through prevention and mitigation. One of the methods to prevent AMD generation is a dry dump cover system that has been proposed to minimize oxidation of sulphide waste rock in dumping sites. The performance of this system depends on the physical and geochemical stability of a barrier layer to minimize water and oxygen influx. In the mining industry, this barrier layer is formed by using Inert/Non Acid Forming (NAF) waste rocks to cover Potentially Acid Forming (PAF) underneath. However, the availability of NAF waste rocks, due to the geological condition, mining sequence and capability of equipment, is limited in some mines. This paper will discuss the acid generation mechanism, application of a cover system and its problem being faced in an Indonesian coal mine, and describe a preliminary laboratory result of a multi layer cover system in an attempt to overcome this problem."

Jan 1, 2011

By L. Barnewold, A. Merchiers, M. Pütz, P. Jeschke, M. Dammers

The mining industry faces many difficult challenges, for example, lower ore grades, smaller and deeper deposits, and longer transportation distances. In the past, there have been remarkable innovations in both equipment and the types of mining methods for which it is used, which have resulted in economies of scale. This has led to an increased use of bulk mining methods, like sublevel and block caving, which has increased productivity and reduced costs. Haulage alone plays a major role. Current haulage techniques are a significant cost driver, which account for between 15 and 30% of the overall capital investment (capex) in a mine and are an increasingly part of the operating costs (opex). The paper introduces a simulation tool of main haulage system in underground mining. Therefore, performances and the costs of the three most common underground main haulage systems, rail, truck, and conveyor, are calculated using a developed modeling tool. The tool was applied and validated in a case study carried out with the LKAB Kiruna Mine in northern Sweden.

By T. F. Tomb

on' January 6, ,1992, the Mine Safety and Health Administration (MSHA) issued an Advanced Notice of Proposed Rule Making (ANPRM) for diesel particulate (DP). The ANPRM identified five areas where the Agency was seeking additional information to assist in the rule making process. These areas were exposure 'limits, risk assessment, consideration of other information, sampling and monitoring methods, and feasibility. The period for submitting information relative to the ANPRM closed July 10, 1992. Prior to issuance of the ANPRM, the agency was involved in conducting studies to evaluate sampling and control technologies and to gather information with respect to occupational exposures to diesel particulate in underground mining operations employing diesel-powered equipment. Since issuance of the notice, additional studies have been conducted to provide supplementary information in these specific areas. Results of these additional studies indicate that average DP levels in coal mines not using aftertreatment range from 0.9 to 2.1 mg/m3. Aftertreatment devices can reduce these levels by approximately 50 to 90 percent. Studies conducted in metal and nonmetal mines showed average DP levels ranging from 0.3 to 1.6 mg/m3.

Jan 1, 1994

By D. Lenartowicz, K. R. Alexander, M Collings

Cosmo Howley is a gold deposit in the Northern Territory of Australia. The geology is complex and the input of geological data is an important part of the grade control process. As the geology of the deposit has become better understood, grade control and mining techniques have evolved to meet the changing circumstances. Present grade control depends on the use of angled blast holes, 21/2 benches and selective mining. Data is processed on site using 2 386 PC's running Surpac software. An environmental protection programme is employed, including soil stripping and stockpiling, sulphide waste containment and water quality monitoring.

Jan 1, 1989

By Francesco Chiappalone, Marco Invernizzi, Franco Gasperin, Brad Yoder, Fabrizio Fara

The Ship Canal Water Quality Project includes a 2.7-mile, 18-ft and 10-in internal-diameter tunnel that extends from Ballard to Wallingford, two popular neighborhoods in the West of Seattle. During the TBM Main drive a 12' × 12' boulder with variable strength up to 47,000psi was encountered resulting on signicant damages to the Cutter ead. The rst part of this paper describes the design and construction of an underground recess in front of the TBM to create a safe working environment for the TBM repairs. The second part describes an injection campaign performed to seal an unforeseen water inow appeared during the excavation of the 11 Avenue Diversion Structure.

Jun 23, 2024

By K. F. Hollberg, D. Graehl, L. Despain

OCI Wyoming's recent expansion of its surface Soda Ash production facilities outstripped the mine's ability to supply Trona ore necessitating infrastructure changes to the mine. A computer simulation of the mine's production systems along with the surface facilities was created to determine the most economic investment alternatives to increase mine production. This paper describes the development of the simulation model; the results obtained, and discusses the issues involved in using simulation modeling for mine production system design.

Jan 1, 2002

By Kyle Amoroso, Larry Applegate, Aaron K. McCain

The use of frozen soil as ground improvement and temporary ground support for the excavation and construction of cross passages and adits has gained in popularity over the last decade. Frozen soil provides a number of advantages for this application such as being waterproof, structurally stable, and working well with any soil type. One of the greatest advantages is the ability for the system to be adaptable to the project geometry and site limitations. Multiple case histories illustrate that freezing can occur from the ground surface, from within the tunnel, or as a combination.

Jun 13, 2023

By R. E. Vivas

Goldcorp is one of the largest gold producers in the world with projects in South, Central and North America. Goldcorp?s flagship operation is Peñasquito, a world-class, poly-metallic deposit that started production in 2010 which is one of the largest mines in Mexico. Since the early stages of the project, Goldcorp has used the most advanced technologies available to maximize its value. However, the implementation of optimum mine plans has been challenging to put into practice. This is due to the fact that the mine operation involves more complexity than the plans usually reflect. This challenge is an industry wide issue that presents opportunities for improvement. This technical session discusses the mine planning methodologies and procedures used to connect long, medium and short term planning strategies in order to bridge the gap and produce optimum mine plans that can be practically implemented in the field.

Feb 23, 2014

By Karl W. Mote, R. K. "Ivan" Urnovitz

One of the Northwest Mining Association's guide-lines is: "If you always do what you've always done, you'll always get what you've always gotten." Another way of saying this is, simply, "when the road curves, don't refuse to turn." Our industry has been roundly criticized for living in the old political world, and, I believe, justifiably so. Until about 20 years ago, members of both houses of Congress deferred to specialists among their members for mining legislation. This was true for all public lands and natural resource issues, and were referred to as the mining bloc, or the timber bloc, or the ranching bloc. We felt safe, and to a large degree, were safe in the sense that western members of the US House of Representatives and of the US Senate understood the need for multiple use of public lands, and the need for the natural resources they supply. They also knew what it takes to stay in business and how to create the economic atmosphere that encourages private industry to find and provide the natural resources. Almost daily, members of our industry bemoan the destructive effects that current regulations, let alone new proposals, are having on American industry. And, there are some intriguing aspects for us to ponder. First, the specific complaint about the government is not regulation per se, but rather that the rules or policies don't make sense. We recognize that few understand our industry, but we have assumed that the government will rely on people experienced and knowledgeable in the area being brought under government controls. There was a time that this assumption was valid, but it is no longer true since we have entered the era of the professional regulator. Much like the MBA who believes that a professional manager can manage anywhere, the new breed of regulator sincerely believes that process is the key to developing effective regulations or programs. They reason the process virtually assures that all the pertinent facts will inevitably come to light and, after receiving appropriate considerations, will result in the proper decision being reached and implemented. Unfortunately, following the process also allows politics to play a new and greater role than ever before, since information based on what can only be called weird-science can now be presented to the professional regulator and accepted as fact. Regulators do not have the background to question the basic tenets of the conclusion being presented to them. To add insult to injury, testimony from people in the industry involved, intended to set the record straight, is too easily discounted as being merely self-serving. A second aspect is that the question of why the associations aren't doing more to stop poorly conceived legislative and regulatory proposals, or to counter the ever-increasing influence of the selfappointed public interest groups is being increasingly discussed. This is occurring despite the fact that there is a higher level of involvement and closer cooperation between the various associations than ever before. This raises a most important question: where are we going wrong? In the last 20 years or so, major changes have taken place. A new philosophy, taking advantage of the public's recognition of need to protect our environment, has swept through the nation, resulting in a whole new body of law enacted to assure environmental protection. We all acknowledge the need to prevent undue degradation during the course of mineral development, and we all consider ourselves to be responsible stewards of the land, because we live and work in the outdoors and know the importance of environmental protection. The changes in the federal statutes apply now to every aspect of mineral discovery, development, and production, and assure adequate reclamation of lands when we are done. Along with the positive changes, are a constant barrage of attempts to stop public land use, or stop mining, or stop any new economic development, ostensibly to "protect the environment," but often reflecting a hidden agenda of social reform. These types of extreme, irrational, and just plain impossible proposals are everyday occurrences, but we have not geared up to challenge all the proposals which could end mining. Instead, we did what we always had done. The road turned, but we didn't. And we wondered why those who had always protected mining weren't doing their job, and why we were having such limited success in reining in the regulators. The Congress had changed, the public demands had changed, the recognition of importance of natural resources had

Jan 1, 1991

By Paul L. Boni

Trona, Na3(CO3)(HCO3) ? 2H20, is mined in quantity from saline facies of the Eocene Green River Formation of southwestern Wyoming. The Green River deposits are the world's largest known resource of natural sodium carbonates. An estimated 127 billion tons of trona ore are known to occur in beds exceeding 4 ft in thickness (Wiig and others, 1995). Twenty-five trona beds, exceeding 3 ft in thickness, and covering at least 100 mil have been identified. The beds are numbered sequentially in ascending stratigraphic order. Trona beds underlie more than 850 mil (bed 17) and are up to 37 ft thick (bed 1) (Culbertson, 1966). Five underground mines, operating in beds 17, 19, 20, 24, and 25, process trona to produce soda ash (sodium carbonate). A total of 11,837,703 short tons of soda ash were produced from 17.1 million tons of trona ore in 1997 (Kostick and Clark, 1998). A detailed study of trona bed 17, using techniques of petrography and X-ray diffraction, has been undertaken in the Solvay trona mine, near Green River, Wyoming. A continuous, vertical-channel sample was taken from near the production shaft for this study. At this location, bed 17 is 12.6 ft thick and includes several stratigraphic markers that are easily correlated throughout the mine and in surrounding drill cores. Bed 17 in this area averages 90% trona through its entire thickness (Wiig and others, 1995) and 95-100% trona in the lower two-thirds of the bed. Mineral impurities include water-insoluble dolomite, quartz, pyrite, clays, and other minerals and partially water-soluble northupite and shortite. Northupite, Na3Mg(CO3)2C1, contributes to chloride contamination in the soda-ash product and is concentrated in the upper one-third of bed 17, which is left behind as roof rock. Northupite has two modes of occurrence: (1) as bedded strata with dolomite, chert, clay, and shortite and (2) between primary trona crystals in trona spar. Petrographic and mineralogic data indicate that this section of bed 17 was deposited subaqueously during its early and late history and may have undergone periods of deposition in a subaerial or marshy environment. Stratigraphic data indicate that trona accumulated at an annual rate of 2-4 in. per year. During trona deposition, dolomite, CaMg(C03)2, precipitated in parting layers when new water entered the lake, freshening supplies of calcium and magnesium. The lack of clay minerals in the trona facies suggests water input may be by means of springs, as opposed to overland flow. Clay occurrences in thicker dolomitic partings within the trona facies indicate periods of episodic overland flow, possibly resulting from storms in the surrounding basin.

Jan 1, 1999

By Dan Ifrim

Soft ground tunneling poses major challenges to the underground industry. Most of soft ground tunnels are in highly urbanized areas, often include limited cover, and include a strong trend of increasing diameters. Therefore, soft ground tunneling works can sometimes cause inevitable ground movements and settlements that may lead to damages to adjacent buildings, roads, structures or utilities; many of these being “lifeline” infrastructure assets. Tunneling operations, Tunnel Boring Machine (TBM) advance rates, and face pressure control can significantly increase or decrease such risks, depending on how well the TBM and operational parameters are applied to the ground conditions. Additionally, the risks of impacting existing infrastructure are heightened in many parts of North America because of cobbles and boulders. To date there is no standardized guideline that determines appropriate tunneling rates nor operator’s guidelines, to ensure safe tunnelling in soft ground. The paper analyzes tunneling records from completed soft ground tunnels to determine a relation between ground conditions, tunnel cover, TBM cutters maintenance and TBM advance rates. The records are discussed to draw several mitigation measures to be adopted during tunnelling, to reduce risks of settlements, over excavation or sinkholes.

Jun 13, 2021

By Salt Lake City Research Center, D. G. Foot, J. D. McKay

As part of its research program on column flotation, the Bureau of Mines, Salt Lake City Research Center has performed studies on (1) column flotation amenability and comparison with conventional flotation results for over 15 mineral systems, (2) alternative methods for improving column bubble generation systems, (3) mineral behavior within a column, and (4) the effect of changes in column operating parameters on flotation grade and recovery. Based on results from these studies, flotation columns (1) are capable of producing higher grade concentrates in fewer stages than conventional flotation cells at equivalent or increased recoveries, (2) require less retention time than conventional flotation cells, and (3) can be divided into cleaning and collection zones that have characteristic mineral-upgrading-per-foot values. Attempts to improve the column air sparger have led to the development of a superior external bubble generation system, which can (1) achieve increased air holdups. (2) produce bubbles from 400 Um to 4,000 Um average bubble diameter with minimal frother addition, (3) provide superior bubble size control, and (4) be maintained without column shutdown. Efforts are continuing to improve column flotation and transfer successful technology to industry.

Jan 1, 1988

By Stephen R. La Brooy, Tong Deng, Pritam Singh, David M. Muir, A. J. Monhemius, G. W. Warren, E. Peters

The controlled addition of ammonia to cyanide solutions inhibits the leaching of copper minerals but extracts up to 80% Au using as little as 10% of the cyanide compared with conventional cyanidation of copper-gold ores. The solubility of copper minerals and copper speciation in solution is dependent on NH3, CN-, pH and Eh. Rotating disc and electrochemical studies show that gold is leached by a mixed Cu-CN--NH3 complex with either Cu(II) or O2 as oxidant. This complex is slowly oxidised to CuCN and Cu(OH)2 by air.

Jan 1, 1993

By Morgan M. Sears

The stability of gateroad pillars is crucial in deep-cover longwall mining, especially during transitions to wider panel layouts. This study evaluates the transition from a 700-foot to a 1,000-foot panel layout with an inter-panel barrier in a deep-cover longwall mine in Southwestern Virginia to identify a configuration that enhances stability and reduces operational risks. Using the LaModel program, three pillar configurations were simulated to assess their performance based on stress distributions and pillar safety factors. These included the previously used 4-Entry Yield-Abutment-Yield layout, the current 3-Entry Yield-Abutment layout with a 220-ft inter-panel barrier, and the proposed 3-Entry Yield-Yield layout with a 320-ft inter-panel barrier. The findings of this study suggest that the proposed 3-Entry Yield-Yield pillar layout is more effective in managing stresses in deep-cover mining environments. By optimizing pillar placement and improving load management, this layout could positively impact mineworker safety and health. The study underscores the importance of advanced simulation tools in developing innovative solutions to address the challenges of modern longwall mining operations.

Feb 1, 2025

By I. H. Douglas

All grade control methods in use currently by the mining industry are imprecise. The methods suffer from being locally inaccurate, leading to are loss and contact dilution. An ore/waste indicator variable can be used to predict the probability of ore occurrence at a given location, Po. Then, an ore grade Zo for an ore location and a waste grade Zw for a waste location are obtained. The expected revenue is calculated at each location, based on its probability of being are or waste, the corresponding grade, and on the cost of mining and processing the ore or the waste. Finally, the decision of whether to recover the block is based on the expected revenue value for that block. The method is illustrated with an example taken from the Jerritt Canyon district in northeastern Nevada.

Jan 1, 1994