Search Documents

By D. L. Whiting

Dump leaching and ,in-situ solution mining have received considerable attention during the past few years due to their apparent economic viability and minimal environmental impact. Solution mining actually dates back to the 17th century when leaching of copper ore was first reported. However-, modern day leaching didn't begin on a wide scale until the mid-1900's. In-situ mining for copper, nickel, salts, and oil shale is currently looking more attractive as the technology advances. Presently, about 15 percent of the copper production in the United States is from leaching operations at approximately 14 active sites, the largest of which are the waste dumps near the Bingham Copper Mine, Utah. To establish a common background, the discussion is centered around state-of-the-art conditions. For dump leaching, complications inherent to the physical conditions and chemical reactions such as channeling, porosity and permeability, sorption, air flow, rock alteration and pH control are discussed. Emphasis is made on those conditions which render solution recovery rates and solution mineral concentrations unpredictable. By illustrating typical and actual field conditions, the generally accepted flow theories for both dump leaching and in-situ solution mining, including rubblization, are presented. For in-situ mining, hydrogeologic techniques such as geophysical well logging, aquifer testing and digital computer modeling are also discussed. The importance of artificial fracturing and well stimulating to solution injection and recovery is made with regard to project development. Finally, the subject of water pollution control techniques and the potential impact of the

Jan 1, 1977

By Richard D. Grove

The on-stream analysis of phosphorus and silica has not been possible by XRF techniques and only recently has some success been indicated with quantitative XRD for P. Yet there has been a recognized need for an on-stream analysis of P and acid insoluble to permit the automatic control of phosphate rock flotation plants which produce some 30-40 million tons of concentrate each year in the southeastern U.S. IMC Fertilizer, Inc., the largest U.S. phosphate rock producer, embarked on a program to develop such an on-stream analysis capability several years ago. Following many months of lab and prototype development, the first commercial installations started in December 1986 and now have completed some 400,000 analyses with surprising accuracy, precision and reliability. The use of these devices in the improved control of the phosphate flotation plant is currently receiving some very serious attention at IMC.

Jan 1, 1989

By Mark Cadzow, Rodney Lamb

CARBAD is a recently developed Australian process for the recovery of gold and platinum group metals (PGM). The process relies on the selective agglomeration phenomena of the gold and PGM to capture the mineral in a carbon-hydrocarbon media. The precious minerals are then extracted from the loaded media by a solvent gold room process producing a relatively pure concentrate. The media is then reformed and recycled. The process development from batch test work to a 5 t/h commercial scale CARBAD plant is discussed. The operation and results of processing a variety of ore types at several alluvial and hardrock gold mines is examined. The operating and capital costs for the CARBAD process shows that it is significantly less than that the conventional CIP/CIL. The environmental safety of the process is a major feature where precious metal deposits are located within urban environments or within wilderness areas.

Jan 1, 1989

By J. F. Abel, R. J. Spengler

Convergence measurement across the 17.4-m (57-ft) high shaft station/loading pocket at Mt. Taylor provided continuing verification of stability and safety. Three levels of instrumentation, consisting of three lines each, were installed and monitored. The instrumentation showed that the flexible lining restrained the adjacent rock. The flexible lining consisted of pea gravel with neat cement between rock and liner plate, wooden crush blocks between liner plate and steel ring beams. The loading pocket is elliptical, 11.6 x 9.6 m (38 x 31.5 ft) inside diameter. The crush blocks were designed to allow 15 cm (6 in.) of convergence. Maximum predicted convergence was 7.0 cm (2.75 in.), and 5.7 cm (2.25 in.) was measured. Convergence measurements also demonstrated decreasing deformation with respect to elapsed time and distance from the measurement station to the temporary bottom of the shaft excavation.

Jan 1, 1987

By T. G. Rozgonyi

The basic goal of this investigation was to determine the degree of drying of high moisture lignite through the use of high temperature and pressure steam autoclaves. Specific items studied were: a) the effect of lignite particle size, b) steam temperature and pressure required, and c) the time of ahydration. Although removal of sodium, ash, sulfur and other ash-forming minerals was not the goal of this study, basic analysis of effluent water showed organic material and alkalai metal content. Removal of inherent moisture from run-of-mine lignite was tested by lock-feeding the lignite, which was previously sized by screening into 25 kg autoclaves. High pressure, up to 4.053 MPa (588 psi), saturated steam was then introduced into the pressure reactor. Reaction time, pressure, temperature, and depressurization rates were strictly controlled for each reactor test run. Results indicate that about 80% of lignite total moisture was removed, including some of the inherent moisture, yielding a non-oxidized, and thus stable, lignite product. As stated, a side benefit occurred as some reduction of non-combustible portions of the lignite also took place. The conclusion reached as a result of the tests is that the steam-drying process can be successfully applied to reducing moisture in lignite, and may be considered for additional studies on acceleration of the coalification process. On the basis of the data presented, the author believes that lignite can be economically upgraded in steam autoclaves by simultaneously reducing the moisture content by 80 percent and the sulfur content by at least 50 percent. Upgrading the lignite by this method will result in large energy and financial savings.

Jan 1, 1984

By S. Tuylu, D. Adiguzel, A. Bascetin, H. Eker

"Tailings can be more stable in-site where they are stored and and so the risk of conventional tailings dam accidents can be reduced by alternative methods. In recent years, surface paste disposal (SPD) method is one of the alternative tailings storage methods. According to the results obtained from the previous lab scale experiments, optimum storage design was determined and then, this design was carried out in-site application under atmospheric conditions by a pilot scale tests. In the field study, two separate dams with no environmental hazards were established by the hazardous waste storage directive, whose surface area is measured as 400cm × 200cm. Also physical changes in the paste tailings were measured by the sensors such as volumetric water content, mutric suction and oxygen consumption. In addition, seepage water was collected in the drainage pool and examined for acid mine drainage and metal mobilization risks. As a result of the preliminary data obtained from measurements of pilot scale tests, when the pH value of seepage in the cemented dam (only 1th and 10th layers with cemented) is about 11, the pH value of seepage in the uncemented (reference) dam is measured at 8-9. INTRODUCTION Environmental damages occurred during the deposition of mine process tailings at surface using conventional methods (tailings dam etc.) can be reduced and/or eliminated with the use of new technologies and methods to an important extent. Nowadays, it has been investigated to safely deposit metal mine wastes generally discharged into surface tailings dams, seas, rivers, creeks etc. using Paste Tailing Technology which gains the growing importance in recent years. Meanwhile, Paste Tailings Technology has two applications in industry as an underground paste backfill and surface paste deposition. Particularly scientific studies about deposition of process tailings as paste sample in underground and surface have been increased. These studies showed that surface paste deposition can minimize the free water amount which is the biggest problem in conventional tailings dams. Additionally, it also provides less particle segregation, in other words, the formation of more homogenous material, the development of geotechnical properties which causes to obtain more stable material, increases the strength and stability of the paste with addition of binder where necessary surface paste material, and reduces the risk of Acid Mine Drainage (AMD) (Bascetin et al., 2017a). Theriault et al. (2003), Martin et al. (2006) and Simms et al. (2007) reported that Bulyanhulu mine in Tanzania is the first gold mine to employ surface paste disposal (SPD) worldwide. Here, tailings are deposited alternately via several towers. The tailings flow away from each tower to forming a conical deposit. Each layer had a lower thickness than 30 cm. The fresh tailings were poured on top of drying and hardening layer after a waiting period of 5-30 days. No cement was added into the tailings to prepare paste material. Uncemented paste was deposited by a solid content of 73% which corresponded to a 250 mm slump cone height (Yilmaz et al., 2014). In a study conducted by Yilmaz (2010) illustrates the preliminary results of a field cell testing undertaken to investigate the effect of in situ climate conditions and material properties on the performance and quality of fine-grained, sulphide-rich paste tailings at the LaRonde mine in Quebec, Canada. A total of two field cells are constructed in the surface disposal site of the mine and categorized as cemented cell CC and uncemented cell UC (Bascetin et al., 2017b)."

Jan 1, 2018

By N. Arbiter

Evidence for the floatability of sulphide minerals without collector is analyzed and it is shown that results obtained with ores, in contrast to those with single minerals or mineral mixtures, depend on many additional variables, some identified and others not. Because of the prevailing low levels and costs of collectors for most sulphide ores, it is unlikely that collectorless flotation will have commercial applications, so that continued research on the subject may be justifiable on theoretical but not on practical grounds.

Jan 1, 1993

By R. Bhaskar

The control of respirable dust in mines has been given paramount importance due to the health and safety implications associated with fine dust. The understanding of the temporal and spatial behavior of dust has been recognized as essential for increasing the efficiencies of the existing control techniques and for developing new control strategies. Mining-related studies in this area are, in general, limited. They are also mostly experimental. Some mathematical and computer analyses have been attempted. In this paper, first a review of the mathematical studies performed in the last three decades in this area is presented. Second, a mathematical model for analyzing dust flow in mines is proposed. The model takes into account a number of factors affecting dust transport. It incorporates varying dust generation source strengths and dispersion, deposition, and coagulation of dust in mine airways. Finally, application areas for the model are discussed. A computer program based on the mathematical model has been developed. The program will output the dust concentration in the mine atmosphere as a function of time and distance from the source. The amount of dust deposited on the sides, roof, and floor of the airway is also determined.

Jan 1, 1985

By P. A. Roberts

A proposal for a modified in situ leaching method for extracting gold from oxidized gold ores using a non-cyanide lixiviant is described. A non-cyanide lixiviant is suggested because of the obvious concerns posed by injecting cyanide-bearing solutions into the subsurface. Oxidized gold ores were chosen as a focus because earlier research on the use of sodium thiosulfate as a lixiviant under anaerobic conditions indicated that the presence of pyrite led to rapid thiosulfate breakdown. A reconnaissance research program involving ore characterization and hydrometallurgical test work on samples from four Australian ore deposits and preliminary reactive transport modeling studies was carried out. This work showed that lixiviant-oxidant combinations of sodium thiosulfate and ferric EDTA and iodide and iodine are both capable of extracting high percentages of accessible gold from the selected samples in bottle roll tests under anaerobic conditions. The ore characterization and reactive transport studies suggested that both physical and chemical methods of permeability enhancement may be required to lift bulk permeability and the availability of gold for dissolution to sufficiently high levels to obtain adequate gold recoveries. Assuming that such methods prove to be both necessary and economically viable, the mining method would no longer be regarded as simple in situ leaching. Therefore, the term ?in-place leaching? has been adopted for the proposed gold extraction system.

Jan 1, 2010

By Z. Rogovin

A Knowledge of the amount of time the material spends in a continuous mill in a closed-grinding-circuit is essential for circuit performance analysis and scale-up design. A convenient method for acquiring this information involves the use of tracers in residence-time-distribution (RTD) experiments. In a typical wet process the RTD measurements are usually done by injecting a pulse tracer into the mill inlet and detecting it in the circuit exit. In this article a simple to use mathematical method for the calculation of the closed circuit material residence time in the mill is developed. Using this method there are no restrictions on the location of the tracer injection or detection points. Any convenient location in the closed circuit can be chosen without affecting the simplicity of the method. This method also enables the calculation of the degree of mixing in the mill. The use of this method for the analysis of impulse response data obtained from several commercial grinding circuits is presented.

Jan 1, 1986

By C. W. Chiaretta

Utah Power and Light Company's Deer Creek Mine had been developed to a point where mine ventilation efficiency had declined to an unacceptable level. Problems identified were ventilation of inactive areas, excessive leakage, and restrictions in the return and intake air ways. Mine management implemented an intensive mine ventilation improvement program to alleviate future problems with respirable dust in the working sections and diesel equipment emissions. Program objectives included sealing of inactive areas of the mine, rehabilitation of high resistance areas, and construction of additional intake and return aircourses. Applications of computer modeling techniques are used to predict the effects of ventilation changes and improvements. Improvements are then prioritized to achieve the largest efficiency increases first. Actual real time assessment of the mine environment and ventilation changes are accomplished with a mine wide monitoring computer system. The Deer Creek ventilation improvement program has more than doubled the ventilating efficiency of the mine.

Jan 1, 1990

By M. Z. Emad, M. U. Khan, A. ur Rehman

Stemming plugs are used as an accessory in drilling and blasting industry. They supplement conventional stemming material (i.e. drill cutting) with retention of gases in the drill hole that result in better fragmentation of rock and improved explosive utilization. Better fragmentation and explosive utilization along with economic benefits enhance efficacy of the project. Incorporation of stemming plugs in drilling and blasting industry is in exercise for about thirty years. The efficiency of stemming plugs is a key factor in their rising induction in mining industry. Different studies have been conducted on the economic viability of these plugs. The focus of this paper is the selection of stemming plugs for a bench blasting operation and the examination of blasting operation efficiency based on ergonomics and human factors. Three types of stemming plugs were evaluated during multiple blasts at a limestone quarry. Their performance was evaluated using split desktop software. Based on the human factors plastic molded stemming plug (stemming plug-1) was found to be the best among all selected plugs. INTRODUCTION Surface mines and quarrying operations heavily depend on bench blasting to achieve high volumetric targets and production demands. Use of explosives is the most economic method adopted for rock breakage and movement. Extensive research had been performed to enhance explosives energy utilization. This include changing the drilling pattern, application of air decks, stemming plugs, and use of other supportive devices. Optimization of explosive energy has been a major concern in those mines that rely on drilling and blasting operation to carry out main production. Due to continually increasing cost, efficient mining demands, and associated hazards of using explosives, it is necessary to utilize explosives at their best. Efficiency of a blasting operation is generally evaluated by the fragmentation size. From post blast conditions at blasting site to efficiency of processing plant, anything can be affected due to improper blast resulting in bad fragmentation. Better fragmentation is necessity for better operation of the system along with consideration of the safety of operation, environmental issues and related costs. For developing a blast design, an engineer should always attempt to minimize the cost of operation without compromising with acceptable technical and safety necessities [1]. Blast performance is dependent on many different factors associated with the process. These factors have been gauged as blast geometry, explosive specification, and rock mass properties [2]. Similarly, in 2013 Mohammad et al. concluded that fragmentation dynamics depends on blast hole diameter, primer, spacing, stemming, burden, and delay timing for blasting operation [1]. At the work site where this study was performed, blast holes were filled by drill cuttings and muds to help in confining gases. In a blast hole, gas confinement helps in better rock fragmentation along with reduced flyrocks. This practice is most common in many countries including Pakistan. Due to lack of homogenized particle size, the effectiveness of confinement is variable and majorly based on the size of stemming. Extremely small sized drill cuttings often result in hole blow out along with flyrocks from the collar. This improper blast energy will result in poor blast, bad impacts on environment, and reduced operational efficiency. In addition to the stemming material, the length of stemming is also a prime consideration. The decrease in stemming length will increase the quantity of explosive in the blast hole and an increase in stemming material generally improves stemming performance.

Jan 1, 2019

By Chris J. Conway, Bruce W. Atkinson, Graeme J. Jameson

The flotation of coal in the fie and coarse particle size ranges presents particular problems. Fine or ultra-fine coal less than 100 microns presents a challenge to conventional flotation machines because the rate of capture of the coal particles can be very low, so longer residence times are needed. Also, conventional mechanical cells are not normally designed with froth properties in mind. Froth drainage may be inadequate, leading to excessive entrainment of ash. The upper limit of flotation of coal is normally put at about 500 um (30 mesh). It appears that, in mechanical cells, coarser particles tend to be torn away from bubbles in the turbulent environment created by the impeller. In this paper, results are presented from plant trials of a high-intensity flotation column of novel design, namely the Jameson cell. Extensive trials have been conducted on coal slurries with a top size of around 1 mm. Size-by size analysis shows that it is possible to achieve high yields of low ash product over the whole particle size range.

Jan 1, 1995

By Jack C. Haptonstall

The Tayoltita Unit of Minas de San Luis, S. A. is situated in an isolated corner of the state of Durango, Mexico. The ore deposits in the region were first worked by Indians, but by 1757 the Spaniards had discovered them, and the first systematic exploitation of the mines commenced. By the early 1900's most of the mines had been acquired by American interests, and the San Luis Mining Company was organized. The modern period of exploitation, uninterrupted for the last 74 years, began. In 1962 the company was fully "Mexicenized" in compliance with the modification of the mining law, and the name was changed to Minas de San Luis, S. A. Tayoltita continues as one of Mexico's most important silver and gold mines. The ore is extracted in en extensive underground operation, mining epithermal fissure veins by selective methods. The ore is milled and treated in an efficient counter-current cyanide plant, where 95 % of the silver and 96 % of the gold is recovered. Current annual bullion output is 55,000 kg (1.7 million troy oz) of silver and 1000 kg (31,000 troy oz) of gold from milling 165,000 try (181,900 stpy). Rough, 33-kg (1000-troy oz) bullion bars are smelted at the mine, shipped by air to Mazatlan, Sinaloa, and are thence sold to the Met- Mex Peñoles smelter in Torreon, Coahuila. Ore reserves, blocked by very conservative methods, are currently at 540,000 tons (595,000 st). Ore reserve grade is 425 g of silver and 6 g of gold per ton (12.4 troy oz Ag and 0.18 troy oz Au per st).

Jan 1, 1976

By William G. Holroyd

In January 1992, the Office of the US Trade Representative announced that the People's Republic of China had agreed to protect US intellectual property, including computer software, sound recordings, agrichemicals and pharmaceuticals. Under the agreement, China will make significant improvements in its patent, copyright and trade-secret laws. Ambassador Carla A. Hills, the US trade representative, said "this agreement should create significant opportunities for US firms interested in marketing high valued-added products to China." Principal beneficiaries will include the agrichemical and computer industries, as well as pharmaceutical, entertainment. The agreement will safeguard these industries' intellectual property, stimulating new exports to China and helping to generate additional growth in the US. Refractory grade bauxite was included in the mineral category of the $1.5 billion of Chinese products on which the US government threatened to impose an immediate 100% trade tariff. Refractory bauxite is available from Guyana and Brazil at higher cost and in different grades. However, refractory brick manufacturers would have had little choice but to pass on the costs to their consumers. Although the United States and China are separated by political ideology and internal governing structures, this agreement recognizes the importance of a $19 billion trading relationship. Consequently, the renewal of China's most favored-nation trading status in the US congress in -June 1992 was all but assured. Many US companies doing business in China and Hong Kong have been quietly increasing their investments since 1989. These companies can now concentrate on developing sales to the domestic Chinese market. This market is expected to surpass 1.2 billion people in 1995 and approach 1.3 billion by the end of the century.

Jan 1, 1993

By G. Reed Marchant

The control systems engineer is often faced with the problem of designing tests or experiments where the cost of obtaining information is expensive. This is true in aerospace as well as in process industries. In these situations the details of test design should be carefully evaluated before any test is executed so that the maximum amount of information is obtained for the effort expended. In recent years there has been a steady trend towards increased automation, In the process industries this has resulted in extensive review of process variables and, instrumentation techniques, development of more accurate system mathematical models, and extensive investments in complex control system as well as completely automated plants. When planning and developing these systems, where each measure of a process variable is usually expensive, it behooves the design engineer to give considerable thought to the details of test design before instrumentation is procured and installed so that the maximum amount of information can be obtained for the expense incurred.

Jan 1, 1968

By H. L. Holden

The single line grinding circuit at Bond Gold's Colosseum mine consists of variable speed drive semi-autogenous (SAG) milling and secondary grinding with a fixed speed ball mill. There are several advantages and disadvantages of operating SAG mills with variable speed drives. Discussion in this paper will focus on the effects of variable speed SAG milling in relation to mill liner wear, grinding media consumption, and mill operating availability. Operating experiences, corresponding mill data, and pertinent design changes are also presented.

Jan 1, 1991

By G. B. McClurg

China was nota factor in the supply of fluorspar to the United States until the early 1980's when it shipped in its first package of Metallurgical lump, that not only was higher grade than the Mexican Metallurgical spar but was also about $30.00 a ton cheaper landed at Burnside. Representatives of the Mexican Fluorspar Institute and several producers made trips to see the Chinese operations supplying their once reserved market place. China, an enigma to most Westerners suddenly became the new contender, with prices that were disgustingly low or so thought the other exporters. Of course China has been mining, producing, consuming and exporting from 400,000 to 500,000 tons per year of various grades of fluorspar but until the first partloads came to the U.S., very little attention was paid to their exports by American-continent producers or consumers.

Jan 1, 1986

By Susan G. Bilhorn

A number of studies have been conducted in active and inactive mine environments using continuous monitoring and data acquisition systems to detect various parameters. In addition to the information obtained for research purposes, these monitoring systems can provide a means to remotely collect required information (such as radon daughter concentrations and air velocity) and control various conditions (such as fan operation and air door position) in numerous working sections of an active mine. Selection of detector locations and placement, which are critical to obtain the information and control desired while not inhibiting mine operations and influencing the detector readings, are covered in this paper.

Jan 1, 1984

By H. Yoon

Several processes involving injection of sorbent and humidification water downstream of the air preheater in a coal-fired boiler unit, are being developed as low capital cost retrofit S02 control options. Extensive laboratory work, pilot plant programs and larger scale programs have developed performance data and design information. Many of these programs were supported by the U. S. Department of Energy (DOE) as "proofs-of-concept" of three different processes proposed by Dravo, Bechtel and General Electric. Based on these project results, DOE formulated a comprehensive in-duct sorbent injection development program to fully commercialize the technology by 1992. Also, EPRI will conduct a 4 MWe pilot program to develop its HYPAS process. The Consol Coolside process is scheduled for utility demonstration in 1989 on a 104 MWe unit at the Ohio Edison Edgewater Station under partial sponsorship of the DOE Clean Coal Technology Program.

Jan 1, 1989