Search Documents

By R. A. Cummings

From before the turn of the century until as recently as the 1950s, relatively shallow coal reserves near the margins of the Illinois Basin were extracted by room- and pillar methods. Subsequent development has, in many cases, extended onto ground with high subsidence potential. The same state of affairs exists in many other historical coal mining districts, as well as in Illinois. Pit subsidence in Illinois is particularly common in the towns of Streator, Carterville, and Herrin, although there are others. Pit subsidence is characterized by distinct circular or oval depressions and normally is associated with shallow mining and thick soil relative to the thickness of rock.

Jan 1, 1985

By Myron W. Mellor

Our efforts at McNally, to find a better way to mechanically separate particles from liquid in a slurry have led to the development of two new centrifuges. The first unit utilizes a slotted opening screen as the filter media and retains all plus 200 Mesh and most of the 200 by 300 Mesh particles. The second unit is a solid bowl centrifuge with a novel method of removing the solids and delivers an effluent containing as little as 300 PPM solids in suspension. The first unit was designed to separate particles in the range of about 1 MM x 0 or smaller top size from the liquid slurry and produce solids having low surface moisture content, and a liquid concentrate containing a low percentage of solids. A prototype of this unit has been in the field undergoing tests for over two years. A few of these test results are shown in Tables I & 11. Testing has been mostly limited to the field of coal, how- ever this does not mean that the machine would accept only coal slurries. The machine has produced a dewatered product having as low as 5.5% surface moisture, and an effluent containing as low as 1.4% solids and handled slurries containing from 15 to 50% solids by weight.

Jan 1, 1975

By K. E. Hjelmstad, W. H. Pomroy

In the event of fire underground, it is essential that all miners be warned as quickly as possible. With mine air rapidly depleted of oxygen and contaminated with smoke and toxic fire gases, any delay in the warning signal could have disastrous consequences. Unfortunately, present mine fire warning systems, such as stench, audible or visual alarms, telephones, and messengers, are often slow, unreliable, and limited in coverage. Recent research by the US Bureau of Mines has established the feasibility of ultralow frequency electromagnetic signaling for underground mine fire warning. Infield testing completed thus far at five mines, signals of from 630 Hz to 2000 Hz were transmitted through rock up to distances of 1645 m (5400 ft) to a pencil-sized ferrite-core receiving antenna and intrinsically safe receiver circuit. Theoretical analysis indicates a capability to transmit effectively for distances in excess of the maximum depths of most American mines, which is about 900 to 1000 m (2950 to 3280 ft) . The prototype system uses off-the-shelf components and state-of-the-art technology to ensure high reliability and low cost. This technology would enable simultaneous and instantaneous warning of all underground personnel, thereby in- creasing the likelihood of successfully evacuating a mine during a disaster. This report discusses the theoretical basis for through-the-rock ultralow frequency electromagnetic transmission, design of the prototype transmitter and receiver, and the results of in-mine tests of the prototype system.

Jan 1, 1991

By Richard D. Christie, K. Jay Pillai

In the past, it was not unusual for coal preparation plants to discard fine run-of-mine coal. This practice has changed due to increasing quantities of fine material, improvements in beneficiation methods, and the need to recover revenue from these fines. It is in this context that the coal industry has increasingly been turning to froth flotation for fine coal beneficiation. Reagent schemes have been developed to promote coal flotation and to treat the resulting refuse material. While reagent technology has improved, however, most plants rely on manual control of reagent dosing and circuit operation. This often results in misuse of reagents, loss of coal recovery, and consequent loss of revenue. Fine coal circuit operations can be dramatically improved through automation. Intelligent process control systems are now in use which are capable of optimizing reagent usage, maximizing coal recovery, and minimizing chemical costs associated with refuse handling. This paper describes a type of control system currently used in preparation plants, and provides data and information on the significant improvements such systems can produce.

Jan 1, 1994

By M. K. Gangal, E. D. Dainty

The CANMET diesel-related work, carried out in cooperation with the Canadian mining industry, resulted in the identification of several useful R/D studies. One such study was the development of a dash-mounted alarm signal system to indicate overexposure of production LHD diesel vehicle operators to toxic contaminants in a mine environment. The resulting instrument has been called the [CO2 Exposure Meter]. This meter is particularly applicable to LHD machines because previous investigations have indicated that operators of LHDs and some haulage truck drivers are exposed to up to 200% of the contaminant concentrations measured in the general mine return air. This paper describes the development of the system which continuously monitors and displays the operator's exposure to diesel pollutants, and indicates an overexposure by an alarm light. The overexposure limits are preset by mine personnel based on carbon dioxide (CO2) measurements, which in turn are related to simultaneous spot respirable combustible dust (RCD) measurements (or to Air Quality Indices - AQI, if available). The CO2 settings are, in general, related to the engine/exhaust treatment selections, vehicle duty cycle and local ventilation rates and efficiency. The system continuously displays one of three lights: green for underexposure, yellow for caution, and red for overexposure. Overexposure can occur for several reasons, such as: reduced ventilation, malfunction of the diesel vehicle, and excessive airborne contaminants. The paper confirms satisfactory operation of the system in a laboratory-simulated mine environment, as well as in field trials.

Jan 1, 1993

By C. Newman, R. C. Ray

Originated and developed in the civil tunneling industry, the Ground Reaction Curve (GRC) has provided a robust methodology for evaluating and designing ground support in both tunnels and underground mining scenarios. This paper presents a preliminary assessment in the utilization of the GRC concept for the evaluation and design of the pillar-support system with respect to overburden stress and displacement. This initial assessment will be based on and backed by past research on this topic. Underground mine instrumentation is planned for a longwall mine in the Appalachian coal field based on the research and findings in this paper to support the postulated hypothesis. INTRODUCTION Since the early 1970’s, the mining industry has evaluated the structural stability of a pillar by dividing an approximated pillar load by an approximated pillar strength. While this design methodology has served the industry well in the past, as modern mining operations continue to develop in more complex geological and geometric conditions coupled with market economics, industry professionals are in dire need of a modified stability assessment approach which considers both the stress condition and material displacements. Within the civil tunneling industry, the GRC approach has been successfully utilized in designing underground support measures that enhance the stability of an underground excavation. Through the incorporation of current industry knowledge and understanding of ground and support behaviors this paper looks to investigate into preliminary assessment for the development of a Modified Support Response Method (MSRM) to further improve the analysis of local and global underground stability. CURRENT PILLAR DESIGN METHODS AND THEIR LIMITATIONS Globally, multiple pillar design methods have been utilized in the design of underground excavations. Each of these methods approaches the calculation of pillar stability a little differently with respect to material properties, underground geometries and stress conditions. Analytical solutions can be used to determine the strength of homogeneous materials like concrete, but not in case of non-homogeneous and non-isotropic mineral deposits in a mine. These equations are often derived using empirical methods. Pillar strength is defined as the maximum resistance of a pillar to axial loading (Brady & Brown, 1985). The strength of mine pillars is typically estimated through indirect methods. In the past, researchers have correlated the strength of a given size and width of a rock specimen to the strength of a mine pillar. The first study on the effect of geometry on rock strength was done by (Bauschiger, 1876) on Swiss sandstone samples. Since then several empirical equations to determine pillar strength had been published by many researchers like (Bunting, 1911), (Griffith & Conner, 1912), (Greenwald, Howarth, & Hartmann, 1939), (Holland & Gaddy, 1957), (Evana, Pomeroy, & Berenbaum, 1961) and (Holland C. , 1964).

Jan 1, 2019

By P. K. Naik, S. C. Das

Leaching studies of low-grade manganese ore containing 31.77% Mn and 23.71 % Fe from Nishikhal, India, were carried out using pyritiferous lignite as a reductant in sulfuric acid medium. The variables studied were quantity of lignite, sulfuric acid concentration and temperature. Regression equations for the extraction of manganese and potassium were determined from 23 full factorial design data. The experimental conditions for the extraction of manganese were optimized using the steepest-ascent method. It was found that 99.03% of the manganese could be extracted in three hours with an ore to lignite ratio of 1:1.8, a sulfuric acid concentration of 1.9 M and a temperature of 99°C. Key words: Leaching, Manganese ore, Lignite, Statistical design

Jan 1, 2003

By K. M. Belingheri, M. E. Smith

Pinson Mining Co. operates a conventional mill and two heap leach operations in north-central Nevada. The latest of these heap leach operations, the Preble project, is a low-grade, low-tonnage property made profitable through several innovative capital reduction techniques. Rapid return on investment was a prime factor in design. To facilitate this, fast-track design and construction techniques were employed. The project is a seasonal 1.5 kt/d (1 700 stpd) crush/agglomerate heap leach plant using both clay and plastic leach pads. Construction and startup were achieved through cooperative arrangements between local contractors and in-house construction personnel, with few items put out to bid. An interactive approach to design minimized lost time and construction costs.

Jan 1, 1987

The Global Mining Standards and Guidelines Group (GMSG) is building an international, multi-stakeholder community to advance the availability and use of standards and industry guidelines for the global mining community. Standards and guidelines are key strategic tools for operational excellence, enabling companies to move forward with efficient, innovative operations with reduced risk. Launched in May 2012, the GMSG is the first international center to bring together information, resources and collaborative projects for mining standards and guidelines, in an open, knowledge-sharing forum. The GMSG is supported by five partner organizations providing outreach and helping to guide GMSG activities: the Canadian Institute of Mining, Metallurgy and Petroleum (CIM), the Society for Mining, Metallurgy and Exploration (SME), the Australasian Institute of Mining and Metallurgy (AusIMM), the Southern African Institute of Mining and Metallurgy (SAIMM) and the Surface Mining Association for Research and Technology (SMART). GMSG was formed under the CIM Surface Mining Society, though its mandate extends to include underground mining as well. ?SME is supporting the GMSG as a key international activity to advance the implementation of standards and guidelines in our industry, and to provide a forum for our members to access, and contribute to, projects and information to assist their operations,? said SME Executive Director David Kanagy. ?We see the GMSG as a good example of ways the major mining associations can work together for the benefit of all our members.? The GMSG charter encompasses all standards and guidelines that apply to mining; however, a number of subject areas are now being spearheaded by six working groups, namely: ? Access and usage of data from mobile mining equipment onboard systems. ? Operational safety. ? Situational awareness (namely, a unified equipment operator interface). ? Underground operations. ? Asset management and operations data definitions and KPIs. ? Energy in communition.

Oct 1, 2013

By G. W. Johnston

INTRODUCTION For many years mining at the Stobie mine of the Inco Metals Co. consisted mainly of fill-type mining for higher grade ores and block caving or blasthole open stope mining for lower grade ores. Open stope mining, although quite favorable in the initial stoping phase, has always presented problems in the pillar recovery phase, especially at depth. In 1966, sublevel caving was introduced. This method is ideally suited for low-grade ore and can be applied very successfully to intermediate or higher grade ores providing proper controls are enforced. Sublevel caving has three distinct advantages: it is highly adaptable to mechanization; it recovers the ore in one operation; and it provides adequate ground sup¬port and safety regardless of mining depth. This method does, however, make extra demands, particularly for new types of supporting services. The constant presence of rock makes quality control of the grade of the ore being extracted essential. Increased de¬velopment, different types of ventilation, roadways, and maintenance are only a few of the many changes re¬quired. The care and maintenance of the fleets of diesel equipment and the modification of equipment is a con¬stant challenge. CHOICE OF SUBLEVEL CAVING The question arises, why mine by sublevel caving? Fig. 1 shows a typical problem encountered by the open stope or blasthole mining method. Near the surface there is little or no ground support problem. As mining progresses to an intermediate depth, however, ground failure starts to occur in the supporting pillars. If open mining is carried beyond this point, the critical depth is soon reached, accompanied by hanging wall caving, ex¬tensive pillar failure, and the danger of losing control of the mining cycle. The rock caved from the hanging wall mixes with and dilutes the ore being extracted from the blasthole stopes. Ore losses occur when pillar failure pre¬vents drilling and development of part of the ore. The interruption to the mining cycle causes serious curtail¬ment in production until ground failure is controlled and the mining method changed to adapt to the new conditions. Having recognized the limitations of open stope min¬ing, alternatives were sought. The first alternative (Fig. 2) was to fill the open stopes with sand fill be¬fore extensive pillar deterioration occurred, recover the pillar ore by fill mining, and then convert to total fill mining below. If the ore grade is high enough it can support the costly fill method. Recovery will be at a much slower rate and will therefore extend over a longer period of time. On the other hand, sublevel caving gives complete primary mining recovery in a short time and is very adaptable to mechanization, which is now a necessity to combat spiralling labor costs and give greater produc¬tivity per man. Sublevel caving is ideally suited as a mining method for low-grade ore bodies which eventually reach a criti¬cal depth for open stope mining. DEVELOPMENT The development phase comes first and of course its main purpose is to gain access to the ore and provide a route for ore removal from the mine. Initially a 20% inclined service ramp is driven in the footwall rock (Figs. 3, 4, and 5). It is preferable to start at the top of a mining block and drive the ramp down¬ grade so gravity can assist in mucking the blasted de¬velopment round, and also access can be gained more quickly to the initial production area. The ramp nor¬mally turns at 3.1 rad (180°) about every 152.4 m (500 ft) to keep it reasonably close to the rock disposal

Jan 1, 1982

By P. Somasundaran

Electrochemical properties of silicate minerals govern their behavior in processes such as flocculation and enhanced oil recovery that can occur at elevated temperatures. Knowledge of these properties as a function of temperature can be helpful in developing an under- standing of the role of these interfacial properties at non-ambient temperatures. Zeta potential of Sodium Kaolinite and quartz has been determined as a function of pH and temperature in this work. Both systems exhibited markedly different behavior at higher temperatures and also exhibited significant hysteresis. Results are examined in terms of possible dissolution of the minerals and surface reactions at different temperatures.

Jan 1, 1986

By S. K. Kawatra, T. C. Eisle

In froth flotation of phosphate, it is important that the flotation be as selective as possible in order to maximize grade and recovery without adding additional stages of flotation. Flotation columns provide a means for improving the selectivity compared to conventional flotation machines and are of considerable interest for phosphate processing. The selectivity of a flotation column is largely limited by the degree of back mixing of tailings into the froth zone, and its recovery is limited by the degree of short-circuiting of feed to the tailings. The horizontally baffled flotation column was therefore developed to minimize back mixing and short-circuiting without introducing problems with plugging or reduced capacity. The introduction of horizontal baffles to a column reduces both entrainment of feed water into the froth and short-circuiting of feed to the tailings, which improves the column selectivity. The results of horizontally baffled column flotation of phosphate are presented for fatty acid flotation of phosphate, with comparison to conventional flotation using the same reagents.

Jan 1, 1999

By S. K. Kawatra, T. C. Eisele

Although column flotation is known to be more effective than conventional flotation for cleaning fine coal, little attention has been paid to the considerable sulfur removal potential of this process. Whereas conventional flotation can only with difficulty remove pyritic sulfur from coal, flotation columns can make this separation readily due to their greater selectivity. This project has used a modified flotation column to remove pyrite from fine coal. This column has been shown to be capable of removing 70 to 85 percent of the pyritic sulfur from coal while recovering 80 to 85 percent of the total calorific value. However, the remaining pyrite is too finely disseminated to be readily removed by physical means. Currently, experimentation is in progress using bacterially-catalyzed dissolution of pyrite in acid solution to remove ultrafine pyrite and aid in the removal of coarser pyrite inclusions.

Jan 1, 1988

By J. J. K. Daemen, C. Fairhurst

Two aspects of tunnel support design are considered, and for both particular attention is paid to the influence of rock failure around the tunnel on the loads developed on the supports. 1) In general it has not been possible to extend analytical methods for the study of rock failure around tunnels to three dimensions. As a consequence it was not possible to calculate either the influence of the face or the actual sequence of support loading as the face advanced. The finite element method made this extension possible. A simplified analysis of the influence of the face and of the sequence of support installation has been made. The influence of the original stress field and of the rock behaviour on the length of tunnel which can be left unsupported (related to the stand-up time) is shown. The degree to which a 2-dimensional analysis can be used to approximate the final support load is shown to be dependent upon the post-failure behaviour of the rock. 2) Tunnel support design requires a knowledge of the forces and of the -rock displacements which cause stressing and deformation of the support system. A 2-dimensional model incorporating a detailed representation of several support systems, of the rock behaviour in the broken zone and of the interaction between rock and support is given. The model allows the calculation of the stress distribution in the support. The significance of the relative stiffness of support and rock on the stresses developed in the support is shown.

Jan 1, 1997

By J. G. Groppo, B. K. Parekh

Removal of moisture from fine (minus 28 mesh) dean coal to 20 percent or lower level is difficult using the conventional vacuum dewatering technique. High pressure filtration technique provides an avenue for obtaining low moisture in fine clean coal. This paper describes a couple of novel approaches for dewatering of fine clean coal using pressure filtration which provides much lower moisture in fine clean coal than that obtained using conventional pressure filter. The approaches involve (a) split stream dewatering and (b) addition of paper pulp to the coal slurry. For Pittsburgh No. 8 coal slurry, split stream dewatering at 400 mesh provided filter cake containing 12.9 percent moisture compared to 24.9 percent obtained on the feed material. The addition of paper pulp to the slurry provided filter cake containing about 17 percent moisture.

Jan 1, 1995

By M. S. Klima, B. K. Kim

The use of a 25.4-mm- (1-in.-) diam water-only hydro-cyclone for separating liberated 125 x 25- µm high-density particles from similar-size lower-density (2.65 g/cc quartz particles, as might be used in soil washing applications, was investigated. As expected, cyclone performance was greatly affected by changes in cyclone geometry and operating conditions. A single-stage separation recovered 75% of the magnetite (4.8 g/cc) while rejecting nearly 60% of the quartz. With ferrosilicon (7.0 g/cc) as the heavy component, the recovery improved to 85%. The use of dense medium in a single stage increased both ferrosilicon recovery and quartz rejection to approximately 90% each. In addition, computer simulations of a three-stage circuit were performed. The simulations showed that recoveries approaching 97% with quartz rejections of 95% were possible.

Jan 1, 1999

By Clement K. Chase, Manuel R. Lastra

Introduction The choice of using a dump or heap leaching process or a fine grinding-agitation leaching process is based on the grade and tonnage of the ore body. Low grade ore and small tonnages are best treated by a low-cost method, such as dump or heap leaching. Permeability, however, is the critical factor in a successful leaching operation, regardless of tonnage or grade. Without permeability in the leach bed, no percolation, no dissolution, no extraction, and no success are possible. Solution delivery to the ore is also essential. Solute-to-mineral contact is a requisite. The solute must be effectively strong and not be depleted in active dissolvers, such as acid, ferric iron, cyanide, and oxygen. It must also be moving across the mineral to be dissolved. No pockets of stagnant solution can be allowed. A third factor is recovery of the now-dissolved metal in the pregnant liquor. All such liquor should be gathered at a reasonable metal concentration to make further pumping and processing worthwhile. Control and recovery of pregnant solutions are probably the most ignored factors of solution mining. This stage in recovery is historically where many operations either fail or become viable. Permeability A permeable heap is normally achieved by taking into account heap building/construction and agglomeration/pelletizing. Even though heap building is critical for good permeability, it will not be discussed here. It has been described in detail by others. Instead, this analysis will concentrate on agglomeration and pelletizing. Differences between agglomeration and pelletizing are emphasized. Agglomeration is referred to when small particles are being attached to larger particles -the ore presents a complete size distribution. On the other hand, pelletizing is a process where all particles are fine (less than 850)µm or 20 mesh), as with mill tailings. The difference is important from two points of view: • Mechanical devices used to achieve the desired attaching action; and • Binder dosages. Mechanical Devices Due to the absence of large particles that fines can become attached to, pelletizing should be done in a centrifugal-action-based device, such as an inclined rotating plate, a rotary drum, or a series of belt-transfer points. In agglomeration, large particles play a part as a natural nucleus for the attaching action of fines. Hence, a tumbling action as strong as for pelletizing is not required. Common methods to accomplish agglomeration include: • Cascade belt system with either all belts moving forward or some of them moving forward and at least one moving backward; • Combination of belt plus inclined vibrating chute; • Large concrete mixer drum; and • Belt discharging directly onto stockpiled ore. The proper agglomeration system will depend basically on the size distribution of the ore and the amount and type of clays present. In all of the agglomerating systems described, the tumbling action takes place at the transfer points either from belt to belt, or from belt to inclined chute ore belt to ore pile. Usually, two or three mixing bars at each transfer point are also included to help the mixing action. Plows to move the ore around on a moving belt are also used.

Jan 11, 1984

By Ernest E. Thurlow

"Western Coal" in this paper is limited to those deposits of subbituminous coal and lignite in the States of Montana, Wyoming, and North Dakota. The characteristics of the coal are discussed as well as the history of mining and current mining operations for steam coal. The future of the region is tied closely to the ultimate conversion of coal to oil and gas products. Problems of industrial water supply and environmental considerations are covered together with a brief review of current legislation's actions affecting strip mining.

Jan 1, 1973

By J. R. J. Edwards

Jaspilite, a mineral consisting of silica and iron oxide in varying proportions, is one of the host rocks of the high grade ore deposits situated in the Middleback Range of South Australia. As a result of laboratory investigations, a flowsheet was postulated for the beneficiation of jaspilite to produce an acceptable grade product for feeding to blast furnaces, The flowsheet involved the reduction of the hematite in the haspilite to magnetite, the grinding of the reduced product to 95 pct minus 325 mesh Tyler followed by wet magnetic separation, hydroseparation and filtration to yield a magnetite concentrate. Agglomeration of the fine concentrate would then be necessary to meet the physical requirements of blast furnace feed. To prove the postulated flowsheet, to obtain a more accurate estimate of costs and to obtain design data for a commercial installation, a pilot plant was constructed at Whyalla, South Australia.

Jan 1, 1960

By M. Board, C. Alexander, M. Ramström, W. Johnson

"Hecla - Lucky Friday is an underground mine that has been in operation for 75 years and produces from depths over 2.3 kilometers (7,500 ft) below the surface. Technical issues at this depth include high rock temperature and seismicity. The use of new innovative mechanization is being examined for ore production. Principal advantages of mechanization are the reduced exposure of personnel, reduced seismic triggers, and increased efficiency. Lucky Friday has partnered with Atlas Copco to design, build, test, and deploy a mechanical miner for primary ore production. We will discuss the background, concept, development and deployment strategy for a mechanical miner. BACKGROUND The Coeur d’Alene mining district in northern Idaho was first discovered over 130 years ago and has been the most prolific silver producer in the US. The Lucky Friday mine of Hecla Mining Company (Figure 1) is the oldest (76 years) and deepest mine in the district, producing approximately 725 tonne per day (800 tons per day) from narrow, vertical lead-zinc-silver veins. Cut and fill stoping is currently employed at depths to about 2.3 km (7,500 ft) below ground surface, making it one of the three deepest mines in the western hemisphere. The #4 Shaft, a winze collared at approximately 1.8 km (5,900 ft) below surface and extending to a depth of nearly 2.9 km (9,600 ft), was recently completed to exploit the high-grade 30 Vein, whose resource has been identified to at least 3 km (9,700 ft) in depth.As with other deep mines worldwide, a number of challenging engineering issues occur, including: high in situ rock stress, squeezing ground, seismicity, high in situ rock temperature that requires refrigeration, diesel equipment that generates diesel particulate matter (DPM) requiring high ventilation airflow rates, and long travel times for worker transport to mining areas."

Jan 1, 2018