Search Documents

By Harry R. Asche, Manfred K. Lechner

The Cross City Tunnel comprises 2km of a new underground traffic route in Sydney, Australia. The route is very complex, involving some six separate tunnels and three underground Y-junctions. For almost 200m the six tunnels run parallel at different level sunder William Street, Sydney. Almost all of the route runs adjacent to the City Business District of Sydney and adjacent to or below many major buildings and services. The planning and design of this project is described. The geometric arrangement is achieved with a strong dependence on 3D road design packages. Road alignment constraints include land acquisition and proximity to existing tunnels and basements as well as maintaining separation from the other tunnels in the scheme. Geotechnical and hydrogeological studies are described. Findings discussed include the high horizontal stress field in the Sydney area and investigation of incised palaeochannels on the route. Methods of design for the tunnels and Y-junctions are described, as well as methods of settlement prediction for the buildings and services. The latter includes the settlement assessment for more than 200 buildings, many in excess of 20 storeys, as well as services including all of the city railway lines in Sydney.

Jan 1, 2003

By B. J. Arnold

Utility coal specifications usually contain a requirement for a maximum moisture content in order to prevent coal handling problems and to minimize evaporative losses in the boiler. As most coal cleaning processes are water-based, dewatering and sometimes drying steps are required to meet moisture specifications. Screens are often used for dewatering, with centrifuges and filters used to further reduce moisture in many cases. Algorithms to predict the performance of screens were developed for the Coal Cleaning Simulator running under Aspen Plus during a project sponsored by the U.S. Department of Energy and the Electric Power Research Institute. These algorithms include calculations for the size separation and a calculation for moisture content of the oversize product based on particle size and specific gravity distribution. This paper discusses the algorithm for predicting the moisture content of coal dewatered by screens.

Jan 1, 1997

By S. N. McIntosh

Column bioleaching was evaluated by the U.S. Bureau of Mines as a means of recovering manganese from a low-grade ore from the Three Kids deposit in Southern Nevada. Manganese was solubilized from the ore using indigenous heterotrophic microorganisms. Diluted molasses medium was provided as nutrient for the microorganisms. The medium was recirculated through the ore bed until the sugars were spent. Two methods were evaluated to recover manganese from the sugar depleted bioleaching solution: (1) adsorption with a weak cation exchange resin followed by stripping and precipitation techniques, and (2) direct precipitation of the manganese using ammonium carbonate. Both methods removed up to 95 pct of the solubilized manganese from the medium as a carbonate salt. After manganese removal, the medium was replenished with fresh molasses and recycled back through the column. More manganese was effectively leached. This process of manganese solubilization and recovery followed by replenishment and recycling of the medium was repeated until 98 pct manganese was extracted from the ore.

Jan 1, 1993

By Z. M. Zavodni, M. K. McCarter

This paper identifies physical conditions responsible for past instability of the Main Hill area in Kennecott Copper Corporation's Bingham Canyon Mine, Bingham Canyon, Utah, and describes successful stabilization techniques employed in this slide zone. Geotechnical highlights of recent slides are presented, including monitoring, geological engineering data collection, hydrology, physical rock properties, and stability analyses. Local conditions responsible for slope movement in the Main Hill zone are: (1) high pore water pressure that causes a substantial decrease in real and effective material strengths; (2) continuous structural systems that allow sliding in the more competent rock zones; and (3) broad areas containing fractured, altered , and incompetent rock and soil- like materials. The failure mode is structurally controlled and involves a circular-type soil failure in the toe region initiated by excessive pore water pressure. A surface mapping method is presented which assigns rock mass quality on the basis of block size and rock substance strength. This site characterization technique has successfully predicted slide boundaries and failure modes; used in conjunction with laboratory determined shear strengths, it has provided basic input for calculating slope safety factors in the Main Hill slide zone.

Jan 1, 1977

By M. S. Riyazulla

The Hutti greenstone belt comprising predominantly of low-potassium tholeitic basalt has undergone regional metamorphism of a transition zone between greenchist to amphibolite facies. The important mineral constituents of the volcanic suite are amphibole and plagioclase which appear to be the product of regional metamorphism. These minerals have been recognized as the main indicators of metamorphic temperature and pressure. With a view to understand the P-T conditions of metamorphism of the belt, electron microprobe studies were carried out on amphibole and plagioclase and the chemical data was used to decipher the metamorphic conditions. The results obtained indicated a metamorphic temperature of about 6000 c and pressure of 5 kbs. for the Hutti greenstone belt.

Jan 1, 1996

By M. Niec

Poland lies at the junction of three geologic provinces: the East European Precambrian platform, the Middle European Paleozoic platform, and the Alpine orogenic belt comprising the Carpathian Mountains. However most of the rocks that contain mineral deposits and many of the recently explored and mined deposits are commonly hidden under thick overburden, sometimes up to over 500 m thick. The discovery of these mineral deposits was due to the combination of geologists talents for inference and the keen interpretation of geophysical data ultimately tested by drilling. Examples of such use of the state-of-the-art geology include the following: 1. Sedimentologic and paleogeographic reconstructions led to the discovery of 8.8 Gt of bituminous coal under 500 m of Jurassic and Cretaceous cover in the Lublin basin, 2. Tectonic and paleogeografic data suggested a potential for discovery of burried Upper Permian copper de-posits on the Foresudetic monocline; subsequent exploration discovered 75 Mt of copper and 0,17 Mt of silver, 3. Geological interpretation of gravity and magnetic da-ta combined with sedimentologic data and regional subsur-face geology resulted in the location of 1.3 Gt of Fe-Ti-V ore in the Precambrian basement of northeastern Poland under -500 m of cover 4. A combination of metallogenic theory and geological interpretation of regional geophysical mapping led to the discovery of Caledonian-Hercynian granites and grano-diorites with accompanying porphyry-type Mo-W-Cu ores below 300 m cover on the northeastern border of the Upper Silesian coal basin 5. Tectonic reconstructions based on gravity and seismic data combined with theory on the origin of native sulfur led to the discovery of 1.0 Gt of native sulfur under cover up to 300 m thick. Five deposits were found at the northern margin of the Carpathian Foredeep. The other deposits found include lignite, polyhalite, lead-zinc ores.

Jan 1, 1996

By T. W. Meikle

Three nutrient amendments and a biological seed inoculant were evaluated for use in establishing vegetative cover on waste rock substrates. Randomized blocks were placed on three substrates. Treatments included two types of organic fertilizer, mineral fertilizer, Azospirillum bacterial inoculant, plus controls. The seed mix consisted of native grass species adapted to low nutrient conditions. Canopy cover has been monitored for three growing seasons. Results indicate: 1) two of three substrates support plant growth following amendment with organic fertilizers; 2) organic fertilizers increase cover substantially over mineral fertilizer; and 3) Azospirillum had no effect on canopy cover.

Jan 1, 1999

By W. L. Dalke

The Minntac complex is a facility for production of iron ore pellets located on the Mesabi Range at mountain iron, Minnesota. It consists basically of a mine, crushing plant, concentrator, and a pelletizer producing twelve and one-half million tons of pellets annually. This paper deals with some of the aspects of the grinding circuits; but prior to that discussion, it might be well to briefly describe the flow of material in the operation. The crude ore, containing from 20% to 25% magnetic iron, is mined by 14-yard electric shovels. .the blasted ore is loaded directly into 50-yard side dump railroad cars and hauled to the crushing plant. Crushing is done in three stages, originally, two 60" primary crushers; four 7-foot standard secondary crushers; and six 7-foot short head tertiary crushers were installed, when the plant was expanded to double its capacity, five secondary and ten tertiary crushers were added. These were duplicates of the original 7-foot standard and short head crushers used in the original construction, there was no expansion of the primary crushers but a one-half-million-ton surge pile of tertiary crusher feed was added.

Jan 1, 1976

By C. J. Greet

Grinding with an electrochemically inert grinding media (i.e., high chrome white iron) shifts the pulp potentials to more oxidising conditions, increases the dissolved oxygen content and reduces the EDTA extractable iron concentration when compared with milling with electrochemically active grinding media (forged steel). These changes in pulp chemistry produce cleaner particle surfaces, reduce reagent consumption, and increase concentrate grades and recoveries. This paper presents a robust laboratory test program that not only demonstrates the changes in the pulp chemistry, but also provide an indication of the magnitude of the metallurgical improvements that are possible. While laboratory studies are interesting, the proof is in the pudding! So, the paper provides an overview of plant trials conducted at several porphyry copper operations around the world: Newmont’s Cadia and Red Chris Operations, as well as Evolution Mining’s Northparkes Operation. These successful plant trials clearly demonstrate that selection of the right grinding media alloy will yield savings in grinding media consumption and reagent consumption as well as increases in revenue through improved copper and gold recoveries. However, many of the porphyry copper mines on the Eastern Pacific are copper-molybdenum deposits. The paper presents laboratory test results for typical copper-molybdenum operations and extrapolate these numbers to what might be expected should a plant trial occur.

Feb 1, 2025

By J. J. Harrington

The pH control system at Kennecott Copper Corporation's Nevada Mines Division concentrator consists of two independent systems, lime dilution and lime addition. Lime dilution is accomplished in a mixing tank where slaked lime and water are introduced proportionately. The desired dilution of the milk of lime is determined by the electrical inputs provided by eight pH probes, one per grinding section. The inputs are averaged and applied to a time base generator. The summation output of the time base generator determines the proportion of lime and water that are to be mixed and applies this input to a voltage sensitive switching device. The switching device provides a signal to one of two relays which will add either slaked lime or water, dependent upon the summation output. The entire cycle is based on a two-minute repetition rate to allow for sufficient mix time. Responsivity is controlled by maintaining a limited maxi- mum solution level in the mix tank. Lime addition is controlled independently within each grinding section. The electrical input from the pH probe in a given section controls the solenoid valves which provide lime to each of the ball mills. The valves remain open within a time range capable of maintaining the pH of flotation feed at a given set point.

Jan 1, 1975

By Paul H. Earl

This paper discusses the evolution of a modeling methodology for explaining price behavior in the aluminum industry. Three generations are described, each utilizing as a foundation a microeconomic stages-of-processing approach. The second generation represents an improvement over the initial version, by incorporating more rigorous specifications of energy cost, and market strength (demand-supply balance) as well as endogenous treatment of market strength. International linkages across prices, costs, and markets, are the major extensions in the third generation. The discussion covers theoretical considerations, data problems and limitations, and model specifications. Simulation and forecasting properties of the models are also addressed.

Jan 1, 1979

By R. K. Singhal, D. B. Stewart

A variety of equipment is being used for roadheading and tunneling in the mining industry. In United States drum-type continuous miners are used most extensively. In Europe and Canada mine roadways are driven mainly by roadheaders. The application of tunnel boring machines to coal mining is somewhat recent. Such machines are however being used on major projects driving main mine entries.

Jan 1, 1985

By Jonq-Keh Lee

This paper deals with the effects of air leakage from intake to return airways through a series of stoppings on the analysis of coal mine ventilation. The mathematical model which assumes continuous leakage along adjoining intake and return airways is reviewed, and a new mathematical approach is presented based upon the concentrated leakage through individual stoppings. The procedure incorporating the new method in the analysis of coal mine ventilation networks is also discussed.

Jan 1, 1984

By K. T. Valsaraj, L. J. Thibodeaux

Solvent sublation, the separation process for the removal of two hydrophobic compounds (penta- and trichlorophenols) from the aqueous phase, is discussed, as is a steady-state mathematical model for fire process. Solvent Sublation "'as conducted in a continuous countercurrent mode. The underlying mechanisms, theory and experimental details on the effects of process variables on removal efficiency are reported.

Jan 1, 1994

By R. F. Korcak

There exists a wide array of industrial by-products that can be shown to produce beneficial responses in the soil/plant environment. These materials range from clean coal technology residues produced in the generation of electric power, particularly those high in gypsum, to mineral 'fines' produced by the aggregates and crushed stone industries. A number of these materials will be examined in relation to potential nutritional interactions in soils and crops with emphasis on trace elements. The significance of utilizing these materials in agriculture as a component of sustainable agricultural systems will be discussed.

Jan 1, 1995

By Alex Stewart

Most iron bearing ores treated by the R=N Direct Reduction Process yield products lower in phosphorus than the initial ores. The sulfur is also removed and generally is in the range of 0.02 to 0.05 percent in the final R=N product, independent of the sulfur content of both the ore and carbon fuel used. The mechanism and thermodynamic justification of the principal reactions leading to the removal of both phosphorus and sulfur and the control of sulfur in the iron concentrate produced are discussed and supported by the results of laboratory experiments. In substantially all iron ores (containing up to 4% sulfur as sulfate) and solid carbon fuels (containing sulfur from 1 to 8%) tested, the rejection of sulfur has been in the order of 90-95%, with not more than 0.02 0.05% sulfur in the final metallic iron product. With respect to phosphorus-bearing iron ores ranging up to 0.70% P205, the rejection to tailings has been in the order of 70-95%, resulting in not more than 0.03 - 0.07% phosphorus in the final product.

Jan 1, 1958

By F. Romero, L. Yacher, M. Orchard

Specific software tools for Statistical Multivariate Analysis combined with real time process data were applied to Concentrator Plant at Compañía Minera Doña Inés de Collahuasi SCM in Chile, basically to two Mill Lines, each one with one SAG mill (32’x15’8MW)and one Ball mill (22’x36’9.7MW). The main objective was to empower the operator actions using process patterns references instead of process variable set-points. Pattern clustering and the analysis of pattern deviations regarding normal or desired pattern, allows for improvements in process control and the further implementation of soft sensors for those variables not included in the initial model.

Jan 1, 2003

By M. K. Gangal, E. D. Dainty

The paper describes the use of portable aerosol monitors in determining real-time concentrations of diesel soot and respirable total dust in dieselized mines. The field studies were conducted in a simulated diesel environment in the laboratory where no other type of dust was present, and in four underground mines with multi-diesel machine operations. Two packages for the real-time monitoring of diesel soot were prepared which included two types of aerosol monitors: a Miniram, model PDM-3, and a Sibata, model PDS-1. These monitors utilize the principle of light-scattering to measure the airborne mass concentration in the environment. The monitoring device results were compared against the Time-Weighted-Average (TWA) values produced by the gravimetric filter sampling method, permitting calibration factors to be determined for each field test. Both instrument packages provided comparable results. The instrument calibration factors varied for different tests, which may be due to different material composition, particle size distribution, density and shape of the aerosols. This approach for real-time determination of diesel soot is found to be simple, inexpensive and easy to use. More field tests for diesel soot determination and further research on size distribution of particulates in dieselized mines are required.

Jan 1, 1989

By J. H. Rowland, A. C. Smith, K. A. Teacoach

Current regulations for fire suppression systems in underground coal mines to protect conveyor belt installations have been in place since the Coal Mine Health and Safety Act of 1969 was enacted. Over time, the coal conveyer equipment being used and ventilation conditions underground have changed significantly, particularly the width of the conveyor belts and the use of belt air at the face. The effect of these new conditions on the effectiveness of suppression systems during a fire is not known. The National Institute of Occupational Safety and Health (NIOSH) conducted a study to evaluate the effect of air velocity, water sprinkler activation temperature and a limited water application time on the effectiveness of water sprinkler fire suppression systems to extinguish large-scale conveyor belt fires. The fire tests were conducted using both new and used 1.8-m-wide, fire-resistant rubber belt that met the Mine Safety and Health Administration (MSHA) flame-resistant requirement specified in Title 30, Code of Federal Regulations, part 18, section 18.65 (also known as the 2G test). Tests were conducted using standard response sprinklers with activation temperatures of 68° C and 141° C at air velocities of 0.5 and 5.1 m/s. Two tests were conducted at both air velocities for each sprinkler activation temperature, one using a new belt and one with a used belt. The results showed that the suppression system was able to suppress the fires in ten minutes to the point that a miner could extinguish it with a fire hose. However, in several of the tests, the fire reestablished itself a few minutes after the sprinkler water supply was cut off and quickly grew out of control. This report discusses the large-scale experimental configuration, the installation specifications of the fire suppression system and the results and conclusions regarding the effect of air velocity, sprinkler activation temperature and limited water application on the suppression system performance.

Jan 1, 2010

Traction of mining vehicles is well understood for a variety of unfrozen road surfaces, allowing optimal design of mine access and haulage roads. However, no such characterizations exist for the frozen or partially frozen surfaces typically encountered in Northern regions. Recent work by U. S. Army researchers suggests methods for characterizing roadway traction for any vehicle on the basis of test measurements made with a standard test vehicle. Such a test vehicle was designed, and several sets of test data were recorded at the onset of winter in Fairbanks, Alaska. This work suggests methods for future research and possibilities for the use of such research in designing drive systems, tires, and mine roads for Arctic and sub-Arctic mines.

Jan 1, 1995