Search Documents

By J. S. Peterson

Occupational noise-induced hearing loss (NIHL) has been recognized by the National Occupational Research Agenda (NORA) as the most common job-related disease in the United States. Roughly 30 million workers are exposed to excessive noise levels or toxins that are potentially hazardous to their hearing. The National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR)is investigating noise controls to reduce operator overexposures caused by haul trucks used in underground metal/non-metal mines. To identify the most significant contributors to the overall sound level, Source Path Contribution (SPC) analysis was conducted. Noise dosimetry and time-motion analysis were also conducted to quantify operator noise exposure. SPC analysis determined that, under high idle conditions, a source near a hydraulic pump mounted to the rear of the engine and the engine cooling fan were the major noise sources. The time-motion/dosimetry analysis showed that the operators accumulated more than 90% of their noise exposures while they were hauling ore to the dump site and traveling back to the load site unloaded.

Jan 1, 2012

By S. Hardcastle

Various controlled and ambient tests were undertaken to evaluate the performance of a variety of digital heat stress monitors, psychrometers and simpler temperature/relative humidity data loggers that measure, or determine, such parameters as: dry-bulb, natural wet-bulb, psychrometric wet-bulb and globe temperatures. In this comparison, funded by the Deep Mining Research Consortium, it has been found that all the instruments can competently measure dry-bulb temperature but the accuracy of other sensors could introduce significant uncertainty. For example the quality of relative humidity sensors and failure to correct for the barometric pressure difference in deep mines, directly impacts upon the calculation of psychrometric wet-bulb. The comparison has shown that the response of dry-bulb and globe temperature sensors can vary widely under different radiant heat conditions; however this would be negligible in most mines. Of more concern is the differing performance of the natural-wet bulb sensors especially at low relative humidity and low air velocity. Furthermore, from these tests and the currently available theory it was not possible to determine if any of the natural-wet bulb instruments measured that value correctly or validate any relationship between psychrometric and natural wet-bulb temperature at low air speeds where their difference is greatest. Consequently the uninformed use of some of the commercially available environmental heat stress monitors or derivations from other instruments could provide erroneous results affecting the work load category that can be accommodated or the rest ratio regime required.

Jan 1, 2009

By Se-joon Kim, Jong-hwa Chun

"‘Gas hydrate’ is the common term for a solid material formed from the combination of various gases as ‘guest’ and water as ‘host’. A series of large-scale scientific drilling and coring programmes conducted since 2000 revealed that natural gas hydrate exists in a wide variety of accumulations in the sediments. The scaled-up onshore and offshore field production tests during the last decade show that gas production technology will be realized to make gas production from gas hydrates viable in the future, recognizing its potentials as one of the future sustainable energy resources.The total produced gas was approximately 470 m3 by the hot water circulation method over 6 days of operation in the permafrost-associated Mallik 2002 project in the Mackenzie Delta of Canada. In the Mallik 2007-2008 project, the gas was successfully produced stably by the depressurization method for 6 days, up to 13,000 m3 cumulatively. The depressurization method applied in the Mallik test was shown to be an effective way to produce gas from gas hydrates. The Alaska field trial to inject mixed gas of CO2 and N2 to exchange CH4 in 2012 was successfully done for the first time to produce maximum 1,270 m3 per day. A remarkable achievement was made by Japan when it completed its first offshore production test in the Eastern Nankai Trough, producing approximately 120,000 m3 of methane by the depressurization method over 6 days in March 2013. The technical challenges and scientific uncertainties obtained from Nankai Trough production test provide Korea with more considerations as to the aspects of well completion, reservoir formation and seafloor stability, sand control, flow assurance, environmental monitoring, and etc., due to the different geological setting and geomechanical properties of the Ulleung Basin in Korea."

Sep 1, 2014

By M. Weatherspoon, S. Gebo, K. Prisbrey

Our objective was to develop a transfer function model of phosphate heap leaching for design, optimization and control. The procedure included analysis of time-lapse photography of a laboratory heap. Our experimental results confirm the predicted system transfer function kinetics. Our conclusion was that the transfer function and z transform that we have developed will allow us to control flow rate and pH online.

Jan 1, 2001

By Steve Kral

The timing was right for SME to celebrate its 50th anniversary in February as a member society of AIME. The mining industry is in the midst of a commodities boom that appears to have legs. Not only is the demand for metals, construction materials and the like increasing in developing nations, but developed nations have also seen the demand for those materials increase at impressive rates. So, in addition to networking and seeing old friends, attendees at the SME Annual Meeting and Exhibit in Denver, CO. Feb. 25-28, had several reasons to enjoy the week — a healthy industry and their society’s landmark anniversary. This annual meeting was held jointly with the Colorado Mining Association’s (CMA) 109th National Western Mining Conference.

Jan 1, 2007

By B. Valentim

The methodology used to obtain fly ash subsamples of different sizes is generally based on wet or dry sieving methods. However, the worth of such methods is not certain if the methodology applied is not mentioned in the analytical procedure. After performing a fly ash mechanical dry sieving, the authors compared those results with the ones obtained by laser diffraction on the same samples and found unacceptable discrepancies. A preliminary study of a wet sieving analysis carried out on an economizer fly ash sample showed that this method was more effective than the dry sieving. The importance of standardizing the way samples are handled, pretreated and presented to the instrument of analysis are suggested and interlaboratory reproducibility trials are needed to create a common standard methodology to obtain large amounts of fly ash size fraction subsamples.

Jan 1, 2008

By D. He

In China, the total reserves of vanadium, reported as V2O5, in stone coal is 118 Mt (130 million st). Recovering vanadium from such a large resource is very important to China?s vanadium industry. The technology now being used to recover vanadium from stone coal has the following two problems in the leaching process: a low recovery of vanadium and high acid consumption. To resolve these problems, a new leaching technology is proposed. The effects of factors such as H2SO4 concentration, liquid-solid ratio, temperature and time, and the types and additions of additives were studied. By adding 1.5% (by weight) CaF2 and leaching the roasted residue of stone coal with 5.4% (by weight) sulfuric acid at 90°C for 12 hours at a liquid-solid ratio of 2 mL/g, the leaching degree of vanadium reached 83.10%. This proposed leaching technology gives a feasible alternative for the processing of roasting residue of stone coal and can be applied in the comprehensive utilization of stone coal ores in China.

Jan 1, 2008

By Eldon L. Abbott, Rebecca K. Bolan

The Florida Department of Transportation, Florida’s Turnpike Enterprise is studying the feasibility of a 1128 meter (3,700 foot) vehicular tunnel to provide direct access for Port of Miami traffic to/from I-395, I-95, SR-836 (Dolphin Expressway) and Miami International Airport. Both Bored and Immersed Tube tunnels were evaluated and re-evaluated for constructing two, two-lane, 11.9 meter (39-foot) diameter tunnels beneath the Main Shipping Channel lying between Watson Island and the Port of Miami on Dodge Island in Biscayne Bay, Miami, Florida, USA. Bedrock Geology of South Florida is predominately very permeable, vuggy limestone with sand seams and occasional voids. Groundwater inflows in deep cut-and-cover excavations, tunnel buoyancy, grouting, maintenance of Port operations and potential/possible environmental impacts to Biscayne Bay were significant issues.

Jan 1, 2005

By R. B. Pedersen, A. Filipa, A. Marques

"Shallow-depth (<200m) high temperature submarine hydrothermal systems are not commonly observed on mid-ocean ridge settings, as most known systems are located within arc - island-arc volcanic settings, often proximal to coastal areas (meteoric waters added). In 2013, during the Centre for Geobiology’s 2013 oceanographic cruise (R/V G.O. Sars), a dredge successfully sampled massive sulfides and hydrothermally altered rocks from the top of a volcanic edifice (~144-284 m depth) located on the northern sector of the Kolbeinsey Ridge. Dredged samples include vesicular altered basalts, and matrix supported anhydrite, barite and barite-pyrite-anhydrite volcaniclastic breccias. Sulfidesulfate breccias depict complex zoning where numerous small vent orifices are distributed with large blades of marcasite that appear intergrown with barite. Native sulfur was observed in one of these small vent orifices. On a microscopic scale, numerous spherical silica-rich structures appear associated to these breccias. These rocks are evidence for the presence of a relatively high temperature (minimum 150ºC) shallow-water seafloor hydrothermal system in the Arctic mid-ocean ridge, far from mainland influence. This new discovery presents a unique opportunity to study the dynamics of fluid chemistry, metal mobility and precipitation in shallow hydrothermal systems. The remote location of this system dictates that fluid recharge will be influenced solely by seawater and magmatic fluids, In July-August 2014 we expect to survey this new field and acquire new and comprehensive data."

Sep 1, 2014

By B. Samoski

In late 1994, EPA and OSM acknowledged that efforts by any one agency or by the many different agencies to remedy the water quality impacts of decades of contamination from abandoned coal mine lands in Appalachia would not be successful if their disjointed efforts were not unified and if the local watershed organizations were not included. The result of the collaboration between EPA and OSM was the creation of a statement of mutual intent which was a pledge by government agencies, watershed organizations, and the industry to restore watersheds degraded by acid mine drainage from abandoned coal. The presenter will describe the evolution of this pledge from a paper promise to on-the-ground remediation projects.

Jan 1, 2002

By Terry M. Tilley, Gregory P. Sherry

Purpose This is a unique project because the mining and tunneling industries have become highly mechanized and cannot normally accommodate a project where surface disturbance must be minimized or eliminated when there is less than 10 feet of ground cover. More traditional less mechanized methods must be employed and the skills and techniques for accomplishing the work have become all but non-existent. Therefore, this article highlights those areas of specialized skills and techniques. Methods The article will describe the design approach, the method(s) of ground support selected, the method(s) of excavation selected, the planning, scheduling and materials selection process. In addition, the article will describe the actual production characteristics and the results of the project. This approach will concentrate on productivities, adaptations to actual conditions and the quality of the end product. The design approach basically was to insure that the temporary support methods were adequate for the excavation and shoring stage of the project. The final concrete liner was designed using conventional structural design methods with the goal of constructing a tunnel that will last 100 years. The methods of support were spiling and variations of spiling in order to provide advance temporary ground support. In this project spiling is steel channel cantilevered and driven into the ground ahead of the working tunnel face which supports the ground allowing the face muck to be removed with overhead protection’. Conclusion This will be a discussion of the applicability of the methods. The actual performance of the excavation and shoring methods will also be evaluated. The final concrete liner completion results, the actual production rates and the conformance with budget and schedule will be addressed.

Jan 1, 2005

By B. R. Zernich

Advances in tunneling technology, such as Earth Pressure Balance and Slurry Shield methods, have allowed the tunneling industry to construct tunnels in increasingly difficult ground conditions. In recent years, a number of civil projects including large diameter train tunnels, subway tunnels, water tunnels, sewer tunnels, and combined sewer tunnels have been successfully completed deep beneath the water table in soft ground conditions utilizing modern day Tunnel Boring Machines (TBM). With the increase in difficult ground conditions and higher water pressure comes the inherent need to utilize compressed air to gain access to the TBM?s cutterhead and cutting tools. This paper focuses on one such instance in Los Angeles, CA in which Traylor Brothers Inc. performed a cutterhead intervention by compressing the heading of an 11-foot diameter tunnel to approximately 3 bar gauge pressure. This paper focuses on the environmental controls used to manage ventilation, oxygen levels, temperature, and pressure, as well as discusses the problems associated with toxic gases and the increased risk of fire. The paper will also cover the physical science of the environment and the increased risks of performing basic job functions while in a compressed air heading.

Jan 1, 2009

Despite the current economic downturn that is now decimating iron ore production, Minnesota?s mining operators remain optimistic about the long-term prospects for the industry. Reflecting this optimism, the development of several new mining projects continues in the state. The future of mining in Minnesota was the featured topic at the combined 82nd Annual Minnesota Section of SME Meeting and 70th Annual University of Minnesota Mining Symposium. More than 500 mining industry professionals, including engineers, executives, mining managers and equipment suppliers from the around the world, attended the meeting, which was held April 14 and 15, 2009, in Duluth, MN. The combined meeting featured a keynote session with three distinguished speakers plus a panel discussion by representatives from several of Minnesota?s taconite producers. The keynote speakers were Curtis Clark, president and chief operating officer, Behr Dolbear, who gave a presentation on the ?State of the Mining Industry.? Phil Newman, chief operating officer, CRU Strategies, spoke about challenges facing the mining industry and James A. Skurla, acting director, Bureau of Business and Economic Research, Labovitz School of Business and Economics, University of Minnesota Duluth, discussed the importance of mining to northeastern Minnesota?s economy. The taconite producers panel discussion included Jonathan Holmes, vice president and operations manager, ArcelorMittal; Ed Latendresse, vice president and general manger, Hibbing Taconite; John Tuomi, vice president operations services, United Taconite and Mike Mliner, vice president and general manager, Northshore Mining. The mangers provided updates on their respective operation The meeting included concurrent technical papers sessions on mining, processing, environmental and nonferrous mining. The sessions included technical papers that provided information on the status of a number of new mining projects in the state. The conference also offered a SME short course titled ?The basics of iron mining.? A tradeshow that featured about 100 companies and organizations offering products and services to Minnesota?s mining industry ran in conjunction to the conference. It was estimated that more than 900 people, including conference registrants and special invited guests of the vendors, attended the tradeshow opening reception. This was the largest trade show in many years. The Minnesota Section of SME also held its annual business meeting during the conference.

Jan 1, 2009

By Colin Rawlings, Simon Pepper, Maria Karakitsiou, John Mathews, Peter Townsend, Russell Bowler, David Keeble, Christopher Darton, Scott Sadler

National Grid needs to maintain a connection between two existing electricity sub-stations (Beddington & Rowdown) in the Croydon (south London) area, and allow the replacement of two 275 kV cable circuits that are buried under roads. This is to be achieved using a single 400 kV cable circuit within a 10 km (6.25 mile) long, 3 m (9.8 ft) diameter high voltage cable tunnel which is being driven through water bearing Chalk, at depths ranging from 5 m (15 ft) to 80 m (262 ft), with four access shafts(12.5 m (41 ft) in diameter) ranging in depth from 10 m (31 ft) to 40 m (131 ft). The Chalk in this area acts as a source of public drinking water supply (PWS) and is protected by areas designated Groundwater Source Protection Zones. To minimise the groundwater risk the design and construction of the cable tunnel and shafts has paid particular attention to the construction materials used, including testing of these construction materials prior to use, developing construction methods (including the design of the Earth Pressure Balance TBM) and maintaining a groundwater monitoring & testing programme prior to and during construction to ensure the integrity of the Chalk aquifer is maintained as a drinking water source. This paper describes the tunnel &shaft design and construction in relation to these particular groundwater environmental issues which set new precedents for tunnel assessment, design and construction requirements in the United Kingdom.

Jan 1, 2007

By Doug Harding

The Niagara Tunnel Project (NTP) is a 10.4 km (6.5 mi) long, 14.4 m (47.5 ft)bored tunnel that will run under the City of Niagara Falls from the Upper Niagara River to the Sir Adam Beck Power Station. The completed project will enhance the capacity of the Sir Adam Beck Power Station by adding 500 m3 (17,657 ft3) of water per second through the tunnel. The paper describes the project in which the world’s largest hard rock TBM at14.4 m (47.5 ft) in diameter is being used to excavate the tunnel. Features of the project include the use of a High Performance (HP) Main Beam TBM, state-of-the-art ground support and tunnel logistics systems. A continuous conveyor is used for muck transport from the TBM to the disposal area. The paper will also discuss the optimization of the TBM system as the tunnel advances through the varying geology. In June 2004 the Ontario Government announced that Ontario Power Generation(OPG) had been given approval to proceed with the third tunnel under the city of Niagara Falls—the first two tunnels were constructed in the 1950s using drill and blast techniques. The third tunnel, appropriately named The Niagara Tunnel Project (NTP), consists of a 10.4 km (6.5 mi) long TBM-bored, concrete-lined tunnel with a finished diameter of 12.5 m (41.1 ft). In August 2005, OPG announced the selection of Strabag AG of Austria, one of the largest construction companies in Europe, as the contractor to build the NTP Project at a price of CAN $600 million. In September 2005, Strabag A.G. selected The Robbins Company of Solon, Ohio to design, manufacture and deliver a new 14.4 m (47.5 ft) diameter High Performance state-of-the-art Main Beam Hard Rock TBM to be used in the excavation of the tunnel. In order to meet the aggressive construction schedule as requested by OPG/Strabag, the TBM needed to be supplied as “ready to bore” within a 12 month period after the contract was awarded to Robbins.

Jan 1, 2007

By Robin B. Dill, Mark Pelletier, Daniel J. Dobbels, Subodh Bhaumik, Daniel J. VanRoosendaal

Although primarily cut-and-cover excavations are required for replacement of the existing elevated I-93 interstate highway through the heart of Boston for the Central Artery/Tunnel (CA/T) project, some mined tunnel construction was also undertaken. The mined tunneling conducted was the 22-m-wide northbound roadway structure which passed below a 20-m-deep operating underground subway station that was built in 1913. The innovative underpinning scheme used to support the subway station during construction resulted in the successful mining beneath the subway station with negligible vertical settlement. Two grouting galleries were carefully mined below the subway structure, and pre-grouting of the granulary, pervious glacial soils and weathered bedrock was carried out from these galleries. The reinforced concrete walls of the underpinning structure were constructed within three stacked drifts that were sequentially mined below each grouting gallery. After 11 cross adits were mined between the grouting galleries, cast-in-place post-tensioned girders that spanned between the stacked-drift walls were constructed to support the subway station. The stacked-drift walls also provided lateral support for the 22-m wide by 29-m long by13-m high opening beneath the girders.

Jan 1, 2001

By Robert M. Valentine, Randall L. Lentell

Interpretive geotechnical investigations were performed for the construction of approximately 15,250 m (50,000 ft) of wastewater interceptor tunnels in Austin, Texas. Subsurface materials consist of claystone (or clay shale), siltstone, altered volcanic tuffs, chalk and limestone. Special conditions include multiple crossings of Onion Creek with cover ranging from about 1/2 to 3 m (2 to 10 ft.), and the potential for mixed-face conditions consisting of water-bearing gravels overlying clay shale or siltstone. The methods and results of the geotechnical investigations are discussed and the inferred construction conditions are compared to those encountered during tunneling. A suggested format is presented for interpretive geotechnical reports for underground construction projects.

Jan 1, 1985

New developments in the non-invasive and real-time measurement of the velocity profile of slurry flow in horizontal pipes will be described. This information can be used to determine the approach and onset of solid deposition on the bottom of the pipe. Having this information in real time can enable operation at lower velocities or higher solids concentration or both while avoiding solids deposition or plugging and their associated operational costs. In addition, advances have been made in the measurement and trending of pipewear on slurry lines. In contrast to manual methods, CiDRA?s system uses a permanently or semi-permanently installed ring of conformable ultrasonic transducers clamped onto the outside of the pipe. These transducers are used to measure the thickness of the pipe under their respective locations. This results in better repeatability, accuracy, and failure prediction, along with reduced labor costs. The benefit is significantly improved pipe wear monitoring in pipelines with abrasive solids. This provides an improvement in the ability to insure safe operation and avoidance of costly operational and environmental damage due to leaks caused by pipe wear.

Jan 1, 2009

By Joel Nonnweiler, Rafael Castro, Ross Webb

The three thousand foot long 66-inch diameter Folsom East Interceptor Section2B was completed accident free, on time and under budget with no measurable surface settlement. The tunnel passed through nested cobbles, highly abrasive sands and gravels, and abandoned mine workings with less than five-feet of cover at times. Preventing settlement was critical since the tunnel passed under a heavily traveled state highway. A pilot project to test microtunneling and pipejacking methods in the same ground conditions abandoned both drives before completing the planned drive lengths. This paper discusses performance of the conventional tunneling method selected to excavate the ground and the effectiveness of the ground modification techniques employed.

Jan 1, 2001

Nuclear power currently produces about 20% of the electricity in the US, with 104 nuclear power plants located in 31 states. The commercial US nuclear industry contributes over $4 billion annually to US workers in salaries and wages. 25,000 new jobs need to be filled in the next 5 years. There are over 30 new power plants under consideration by US utilities. The operating reactors use uranium oxide fuel enriched to about 4% U235 and fission is the process used to generate heat to form steam to drive the turbine generators. Nuclear energy is an important element in the US generation portfolio and represents the largest producer of nearly emission-free electricity. Most, if not all, of the operating plants will secure an extended 20 years of operation or more. The last plant constructed was ordered in 1978. New smaller, modular reactors are under design to provide less expensive, expandable generation options.

Jan 1, 2011