Search Documents

By S. K. Singh, J. Shepherd

Feather-edging, a major source of injury and fatal accidents in Australia, South Africa and the United States, refers to a phenomenon in which the roof at the goaf edge falls, often suddenly, as a thin wafer of rock that overrides conventional timber breaker lines. The fall may adversely affect a working bord at a distance of 15 m (50ft) or more from the goaf edge. Feather-edging typically occurs in relatively massive, strong roof strata such as sandstone or conglomerate. This paper presents the results of a test in which a concentrated row of fully grouted bolts were used to prevent feather-edging in an Australian pillar- ("total-") extraction coal mine. The test demonstrated that the bolts could resist feather-edging.

Jan 1, 2000

By T. Yegulalp, K. S. Lackner

Zero emission coal plants capture their own CO2 emissions. Since they have no smoke stack, they emit no pollutants to the air. Zero emission plants circulate a gas stream, to which fresh fuel is added and from which spent fuel and impurities are removed as solids or liquids. Coal is gasified via hydrogenation, steam reforming or CO2 gasification (Boudouard reaction). The gas is oxidized in a fuel cell and the resultant water and CO2 are partially removed before returning the remaining gas to the gasifier. The high conversion efficiency of zero emission power plants, which exceeds 70% even in realistic designs, stems from combining fuel cells with careful heat management. The paper generalizes the concepts and outlines the thermodynamic basis of zero emission power plants.

Jan 1, 2004

By W. P. Staunton, K. Jones

INTRODUCTION The increased activity in the Aus­tralian gold industry over the last decade has resulted in a concomitant increase in the use of sodium cyanide, with a projected consumption of 80,000 tonnes in 1991. Growing environmental awareness by government, industry and the public has generated increased interest in the fate of cyanide near gold mine tailings dams and has highlighted the lack of basic knowledge in the area, particularly for Australian conditions. In 1989 the Chemistry Centre (W.A,) commenced a' project, under the auspices of the Australian Mineral Industries Research Association entitled "Fate of cyanide in the Enviroment Near Mine Tailings" to investigate some of the issues arising from the management of tailings containing cyanide, The project, which has been supported by thirteen companies has three broad aims:

Jan 1, 1991

By Byron K. nelson, David Mathieson

Until quite recently concentration of free gold in gravity circuits ahead of froth flotation and/or chemical treatment was considered an uneconomical pursuit in many gold pi.ants in Australia. Over the past 10 yenrs since initial introduction of the Knelson Gold Concentrator, over 600 hnvc been surpl led world wide and they have been developed to the stage that Lhey can now be utilised in almost all instances where free gold appears in significant quantltles ln grinding circuits. They out perform and displace more conventional gravity sepnration equipment such as spirals, tables, sluices, jigs, drum separators etc.

Jan 1, 1991

By R. B. McCammon

Four areas have been identified as favorable drill-site locations for determining whether or not a suspected prophyry copper deposit exists in Rowe Canyon, Nevada. Favorability is based on the similarity to a deposit model constructed from geochemical data for the porphyry copper deposit near Ely. Favorability is defined as the coincident number of positive anomalies for the elements zinc, silver, arsenic, antimony and iron. The favorable areas coincide with an observed magnetic high and areas in proximity to major faults.

Jan 1, 1979

By William R. Nash

Case histories of water problems in underground mine shafts and tunnels are outlined to illustrate varying degrees of sophistication in grouting techniques currently applied in such construction. The interception of water underground can be one of prior knowledge, i. e., the site investigation provides necessary data to plan a grouting program prior to construction start, or excavations may encounter "changed conditions" or unplanned water. The latter includes catastrophic inflows and emergency situations where the structural integrity of a building or concrete shaft lining are jeopardized. The presentation of this paper outlines some applications of grouting work in underground mine construction throughout the United States in a variety of geological provinces and for a variety of minerals.

Jan 1, 1984

By Jr. Pickering

Kaolin is mined from extensive sedimentary formations in the eastern Amazon River Basin of Brazil. Production began about 25 years ago from 30 meter thick beds of ultra-fine particle clay of superior viscosity along the Jari River north of the Amazon. Operated by CADAM S.A., capacity now exceeds 750,000 tonnes per year ot high glossing paper coating kaolin product. South of the Amazon on the Capim River are two new operations: Para Pigmentos S.A. and Rio Capim Caulim S.A. The purity , and large coarse plate-shaped particles of these Capim kaolins support production of superior brightness and whiteness paper coating and filling grades. Annual capacities are reported to be 150,000 to 300,000 tonnes each, with expansions planned. Most of Amazon area kaolin production is shipped to western European, Asian, and North American markets.

Jan 1, 1999

By A. C. Barlow

The use of deep wells for waste disposal is not a new technique. The production phase of the oil industry has been using this method to dispose of unwanted oil field brine since the 1930's The adoption of this method by other branches of industry, however, to dispose of manufactured wastes is a relatively new development, but one which is finding increased use (2). Deep well waste disposal is not an ordinary technique even though it is finding relatively wide application. In fact, just the opposite is true; it is still a rather extraordinary measure. It is not now, nor is it ever likely to be a disposal method which can be assured of success before it is tried.

Jan 1, 1964

By James Withers, Dongbo An, Jinhong Zhang

A micro-scale investigation was carried out by applying an atomic force microscope (AFM) and attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopy to study in situ the adsorption of three different collectors — oleic acid, octanohydroxamic acid (HA) and salicylhydroxamic acid (SHA) — on bastnaesite in aqueous solutions. The results show that all three collectors adsorb on bastnaesite. The hydroxamic acid collectors — HA and SHA — adsorb on bastnaesite mainly in the form of insoluble metal hydroxamate. Their specific adsorption mechanism indicates that high selectivity will be achieved with a hydroxamic acid collector for the flotation of bastnaesite.

By James A. Finch, Xiang Zhou, Yue Hua Tan

Widely used as collectors for nonsulfides, amines also show some frothing properties. Evaluating frother functions of amines and their combination with conventional frothers addresses whether one reagent delivering both collector and frother functions compromises the efficacy of either. From the findings, whether blending with frother confers any benefit requires knowledge of the residual amine concentration. If it is below about 10 ppm, blending eliminated coalescence, but there appears to be no benefit if the concentration is above 15 ppm.

By C. Beul, R. Schipper, L. Santisteban

The Garfield Mine is a legacy vanadium mine in western Colorado with multiple mine openings, waste rock piles, and adit seepages that Cyprus Climax Metals Company (a Freeport-McMoRan Inc. subsidiary) voluntarily remediated through the Colorado Voluntary Cleanup Program (VCUP). The process to obtain a No Further Action determination from the VCUP is presented. Water treatment of the adit discharge, which is not part of the VCUP, is also presented. The remedial action objectives (RAOs) included preventing direct human or biotic exposure to the waste rock and radiation emitting from the waste rock; reducing metal concentrations and radionuclide activities in adit discharge and keeping the discharge from leaving the site; maintaining the existing undeveloped character of the surrounding landscape; and eliminating the need for a stormwater permit. The design included regrading, installation of an infiltration barrier and rock cover, a diversion channel, and a biologically based passive remediation water treatment system. An initial lab-scale evaluation provided design criteria for the full-scale system, which consists of a sulfate-reducing biochemical reactor and post-treatment aerobic polishing cells. The system has been operational since construction was completed in late 2016. Results indicate that the treatment objective of 90% bulk removal of constituents of potential concern (COPCs) is largely being met. The system also provides year-round operation and non-point discharge of effluent. After 20 plus years of site investigations, the remedial action was completed in 2016 with all RAOs met and a No Further Action determination granted in 2018. INTRODUCTION The Garfield Mine is a legacy vanadium mine located approximately 11 miles north-northeast of Rifle, in Garfield County, Colorado. It was leased and operated intermittently from 1929 to 1975 but was never operated by Cyprus Climax Metals Company (Cyprus) (a Freeport-McMoRan Inc. subsidiary). Prior to reclamation, site features included: • six mine openings—five adits and a vertical opening; • two adits discharging mining-influenced water (MIW)— Adit 1 at less than 4 liters per minute (L/min) and Adit 2 at 7 to 10 L/min; • main waste rock pile (13,500 m3) and small waste rock pile (minimal volume); • debris (small structure, mattress, bottles, shells, etc.) indicating site used for recreational purposes; and, • unimproved road, which has been used to access forest fires.

Jan 1, 2019

By Donald G. Rogich

The concept of initiating a large action-oriented contract, directed toward inherently safe mining systems, was conceived by the U. S. Bureau of Mines in January 1970. At that time we were in the process of establishing research contracts and grants, about 100 of which were let in FY 71 to deal individually with fairly specific technological areas. These projects in the aggregate covered a wide spectrum of health and safety problems. What appeared to be necessary was the creation of a project or program that would provide a focal point for the demonstration of many of the results of this research and also in the action sense culminate with working hardware and systems that could be tested and demonstrated over a fairly long teen. The concept of working demonstrable systems, rather than just a conceptual study, was, felt to be necessary for two significant reasons. In the development of any new system, the translation from concept to working hardware is usually a costly and time consuming process which acts as a deterrent to implementation. Secondly, many decisions in the mining community to change equipment or systems ,are based on first hand observation of the new system, in operational practice, an attitude which is certainly understandable in view of the high capital costs of equipment. The decision was made to procure a single R&D contract which would be aimed at developing underground coal mining systems which

Jan 1, 1972

By Prakash C. Kapur

A principal first order and a minor summation term contribute to the solution of the discretized batch grinding equation when formulated in cumulative retained mode. Depending on the interrelationships between the selection and breakage parameters, the minor term may be advantageously modified in a number of ways. The reduced grinding equations thus obtained are solved by iterations to give relatively simple solutions which are tested against experimental data. The implications and advantages of the reduced grinding equations are briefly discussed.

Jan 1, 1969

By Thomas P. Meloy

Floating "fines" differs from floating "sands" because the fines have a much larger surface area compared to their mass. The forces that arise from this large specific surface the key to understanding the behavior and treatment of fine particles. Though the nature of these forces is not thoroughly understood, enough work has been done to give a qualitative picture of what is happening in a flotation cell. It is the purpose of this chapter to re-examine some of the more, recent theoretical work and-to indicate its importance.

Jan 1, 1962

Little knowledge is available that considers the effects of continuous miner position on the possible respirable dust exposure of the remote mining machine operator. Such information could be very useful for increasing the awareness of the remote operator as to those parts of an extended cut that generate higher levels of respirable dust. This data could be used to develop guidelines for positioning the remote operator to reduce his potential exposure. This work details the effects of continuous miner position on dust levels measured on the machine and at the remote continuous miner operator location.

Jan 1, 1998

By James C. Norman

The boron review arrived too late to appear in the June issue. The US was the world's second largest producer and the largest consumer of boron compounds during 1990. Boron mineral concentrate and chemical production in the US totaled 1.13 Mt (1.2 million st), including 565 kt (662,800 st) of boric oxide (B2O3) in 1990, according to US Bureau of Mines estimates. Total value amounted to $404 million. This was slightly higher in production than 1989 but down in value, reflecting a softening in boron product prices. Total world production of boron mineral concentrate and chemical tonnage in 1990 was estimated at 3 Mt (3.3 million st), which corresponds to about 1.3 Mt (1.3 million st) of BO,. World production in 1990 was about the same as in 1989.

Jan 1, 1991

By Basilio Giurgola, Federico Bonaiuti, Norbert Fuegenschuh

The North East Boundary Tunnel (NEBT) project in Washington, D.C. requires design and construction of several SEM adits which have to be built between lateral shafts and the NEBT-TBM Tunnel. The paper describes ground improvements, the actual excavation, and also the final lining works. Schedule and sequencing restrictions provided some unique challenges which had to be considered when designing and constructing these mostly short, but essential portions of the project

Dec 1, 2022

By G. A. Parkison

The sequential copper analysis method is a particularly useful technique to semi-quantitatively define the geologic, mineralogic, and metallurgical types and zonations commonly associated with porphyry-type copper deposits. The method is based on the partial dissolution behavior displayed by the prevalent copper minerals malachite, chrysocolla, chalcocite, and chalcopyrite to solutions containing sulfuric acid and sodium cyanide. Results from sequential analyses of the sample and analytical residue using sulfuric acid followed by sodium cyanide and then aqua regia solutions when compared with conventional total copper analyses can determine the amounts of leachable oxide minerals, leachable secondary sulfide minerals, and primary copper minerals, respectively. Sequential assay analytical results and interpretation are presented for copper deposits in Chile, Mexico, and the United States.

Jan 1, 1995

By Klaus Grebe

Recent investigations by Mannesmann Research have shown that disintegration of sinter with widely varying quality levels is subject to a much more complex set of influences than was previously assumed. It was confirmed that disintegration at temperatures between 300 and 600 °C is triggered by the degradation of hematite. The specific tendency of hematite to disintegrate is, however, not constant: sinters containing the same amount of hematite can show widely differing disintegration tendencies depending upon structural homogeneity, porosity and gangue quantity. Especially sinters with heterogeneous structures transmit stress to the hematite phase and this favours disintegration. Another factor is the brittleness of the glassy silicate phase, which can be influenced even by small modifications of minor gangue constituents.

Jan 1, 1981

By Robert L. Cheek, Sid McIlveen

Sodium sulfate is an important industrial chemical. As recently as ten years ago it was produced and consumed in the United States in quantities exceeding 1 Mtpy. Since then, both its production and use have declined; however, approximately half the production still comes from natural sources. [Fig. 1] illustrates the history of production of natural sodium sulfate in the United States. Production of natural sodium sulfate from various types of deposits is the main source of this chemical in Canada and Mexico, and probably in Argentina, Chile, Iran, Spain, and the Russian Republics. MINERALOGY AND PHYSICAL PROPERTIES Sodium sulfate is widespread in occurrence and is a common constituent of many mineral waters, as well as seawater. Atmospheric precipitation contains sulfate; it is one of the major dissolved constituents of rain and snow (Davis and Dewiest, 1966). Many of the saline lakes throughout the world contain varying amounts of sodium sulfate. Because sodium is usually the dominant cation, some workers make an anionic distinction, referring to lakes containing predominantly sulfate as bitter lakes and those containing predominantly carbonate as alkali or soda lakes (Bateman, 1950). Sodium sulfate in its natural form is found in two principal minerals, mirabilite and thenardite. Mirabilite, the hydrous form, is commonly called Glauber's salt. It was discovered by the German chemist, J.R. Glauber (1603-1668), who derived its name from the Latin, sal mirabile, meaning wonderful salt. Thenardite, the anhydrous variety, was named for the French chemist, Louis Jacques Thenard (1777-1857) of the University of Paris (Mitchell, 1979). The largest quantities occur in the form of mirabilite. Sodium sulfate is found in varying degrees of purity, from theoretically pure efflorescent crystals of mirabilite to combinations and admixtures of other salts and impurities. It is a common constituent of some brines; from this source much is extracted commercially. Sodium sulfate also is found in compounds, such as the minerals glauberite, the double salt of anhydrous sodium and calcium sulfate, bloedite, the hydrous double-salt of sodium sulfate and magnesium sulfate, and burkeite, the anhydrous double-salt of sodium carbonate and sodium sulfate. Over 40 minerals contain sodium sulfate in varying proportions; many are of special interest because of their frequent occurrence. Table 1 lists some sodium-sulfate bearing minerals. The reader is referred to other publications (Cole, 1926, Dana, 1932, Grabau, 1920, and Dietrich, 1969) for descriptions of these minerals. Only mirabilite and thenardite will be described herein. Mirabilite Na$04.10H20, contains 55.9% water of crystallization. It is noted for its efflorescence or spontaneous loss of water. On dehydration it changes to the anhydrous form, Na2S0,. Mirabilite is an opaque to colorless, water-soluble mineral that tastes first cool, then slightly bitter. It has a specific gravity of 1.48. It frequently forms as efflorescent, needlelike monoclinic crystals, but generally is found in the massive form. Thenardite, the anhydrous mineral, Na2S04, contains 43.68% Na20 and 56.32% SO3. It ranges from colorless to white and may be tinted shades of gray or brown. It is a water soluble mineral with a slightly salty taste. Its specific gravity (2.67) and hardness (2.5 to 3) exceed those of mirabilite. It commonly occurs in the massive form without visible crystals. Its crystals are frequently tabular pyramids of the orthorhombic system. Sodium sulfate also occurs as a heptahydrate, containing seven molecules of water, but this is unstable and has not been found in the natural environment. The solubility of sodium sulfate has an important effect on the crystallization of the salt in nature, as well as in its production. Its solubility in water generally increases as a nonlinear function of temperature. Below 1.2°C, ice and mirabilite form. As the temperature is increased above O°C, increasing amounts of sodium sulfate become soluble. At 32.4°C, a transition point on the solubility curve is reached, as the decahydrate melts in its own water of crystallization and the anhydrous form crystallizes. With in- creasing temperatures, solubility decreases somewhat. The presence of other dissolved salts changes the transition temperature and solubility characteristics of sodium sulfate.

Jan 1, 1994