Search Documents

By Robert M. Stevens

INTRODUCTION Truck haulage of muck in underground mining operations has been in use around the world for many years. From the late 1.950s into the early 1970s, haulage by means of load-haul-dump (LHD) units challenged haulage by means of trucks, and, to a large degree, LHD units dominated the trackless concept of moving mate¬rial underground. However, beginning in 1975, the emphasis began to shift back to the use of trucks, with LHD units assuming the secondary role of loading the trucks. Over the years, several manufacturers have been offering trucks with capacities ranging from 4.5 to 45.4 t (5 to 50 st) and with features that specifically address the constraints of underground operation. TRUCK TYPES Three different types of trucks are available for use underground, namely the tip dumpers, telescoping dumpers, and push-plate dumpers. The following para¬graphs describe each of these three types. Tip Dumpers Tip dumpers are designed to lift the truck box, using gravity to dump the load out the rear of the box. The primary application of these trucks is in the haulage of muck to the surface. However, these trucks also may be utilized underground, if a chamber is provided to accommodate the raised truck box at the dumping point. Fig. 1 illustrates a four-wheel drive truck with a 10.0-t (11-st) capacity; this truck is only 1.9 m (6.25 ft) wide and is designed specifically to follow narrow and winding vein courses. Fig. 2 illustrates a two-wheel drive tip dumper with a 24.5-t (27-st) capacity; this truck operates on 12% grades with firm dry surfaces and in modes both loaded-up and loaded¬down. Telescoping Dumpers Telescoping dumpers specifically address the constraints imposed by low back heights, and they represent an optimization of compressed envelope size with maximum payload capacity. Figs. 3 and 4 illus¬trate a typical telescoping dumper with a capacity of 18.1 t (20 st). Fig. 3 shows the box in position for carrying the load, and Fig. 4 shows the same truck with the box in the full-dumping position. Fig. 5 illustrates the loading and dumping cycles. Fig. 6 illustrates an approximation of how an LHD unit with an eject-o-dump (EOD) bucket would be used to load over the rear of this type of truck. Fig. 6 shows a low-profile telescoping truck in the first stage of loading, with a 6.8-t (7.5-st) LHD unit equipped with an EOD bucket. A loader with a smaller capacity and a narrower bucket would allow the bucket to fit inside the truck box and would achieve an even lower loading height than that illustrated. Gen erally, an LHD unit equipped with an EOD bucket and teamed with a telescoping dump truck can be used with a lower back height than could any other front-end loader and truck team. Push-Plate Dumpers Push-plate dumpers are similar to telescoping Bump¬ers, except that they do not have the two-stage box. Instead, push-plate dumpers utilize a single push plate to discharge the load out the rear of the box. Gen erally, these units are limited to payload capacities of about 9 t (10 st). Fig. 7 illustrates a typical push-plate dumper.

Jan 1, 1982

By Ottmar Burghardt

Sintering of iron ore has undergone a dramatic development world-wide. Today, the annual world production amounts to approximately 600 million tons. At present, the sintering process in competition with pelletizing, seems to offer certain advantages inasmuch as it allows the use of solid fuels. Also, its charging behaviour in the blast furnace is, in general, considered as being better than that of pellets. This is true, in particular, for the charging behaviour and the gas permeability in relation to the grain size. Moreover, instead of charging limestone into the blast furnace, for instance, the basic components which are necessary for the burden materials can generally be supplied in a simpler and more cost-effective way by using basic sinter instead of basic pellets. While in sintering, with basicity rising to the range of 1.6 to 1.8 CaO : SiO2, the capacity increases and the sinter quality shows improvements in most of its characteristics, the pro¬duction of basic pellets generally requires a higher fuel rate, when compared to acid pellets, while production capacity decreases and some of the quality characteristics deteriorate.

Jan 1, 1982

By Virginia T. McLemore

The Black Hawk district in New Mexico hosts an unusual type of deposit: arsenide five-element veins. These deposits are Ag-Co-Ni-Bi-As-bearing carbonate veins with local concentrations of U, Pb, Zn, Sb, and other elements. They are high-grade silver deposits (1000s g/t Ag), but low tonnage (<1 Mt) and difficult to find. By 1881, claims were staked and a town developed. It is estimated that >$1,500,000 was produced in 1883–1893, when Ag prices dropped due to the 1893 Ag panic. Solid Silver Mining Co. produced $600,000 from the Black Hawk mine; one car load contained $28,000 worth of silver! The town of Black Hawk grew to 125 population by November 1883. By the end of 1893, the town was vacant; nothing remains. The district was idle until 1916, and the mines operated sporadically since because of lack of available capital, water issues, and difficulty in finding ore shoots. The area is a favorite for mineral collectors. Tungsten was found in the district in 1935 in quartz veins associated with pegmatites. Metal production from 1881–1960 is estimated as 3,000 lbs Cu, 1,000 oz Au, 1,286,000 oz Ag, and 4,000 lbs Pb. In addition, 10,542 short tons of 2.7–71% WO ore and 615 short tons of fluorspar ore have been produced from the district.

Feb 1, 2025

By Tom Plouf, Deepak Malhotra

INTRODUCTION The U. S. mining industry experienced a severe recession in the early 1980&apos;s. This resulted in the realization that the domestic mining industry had to compete on a global basis and only the strong or the low-cost producers would survive. The economic viability of a mining company not only depended on maximizing mineral recovery but also on its ability to do so at minimum cost. Companies had to become more productive not only by cutting costs, but also by developing and/or evaluating new technologies in existing or new plants. Several innovative concepts, including in-pit crushing and conveying, fine crushing, improved classification equipment, flotation, column flotation, pressure filtration, etc., have been developed in recent years. This paper addresses the impact of new flotation concepts and equipment on mill design. MILL DESIGN PHILOSOPHY Modern mill design, especially for large capacity plants, has its foundation in minimizing capital and operating costs. Capital costs can be minimized by minimizing the various components of the capital cost: infrastructure, equipment, instrumentation, structural, initial spare parts costs, etc. All these costs are minimized by simplifying the mill design and/or process flowsheet. The simplified process flowsheet, where applicable, consists of a single stage primary crusher followed by a semiautogeneous - ball mill grinding circuit to produce feed for a flotation circuit. Multiple flotation circuits have been eliminated in most cases. These concepts minimize the cost and encourage the use of large capacity equipment while maintaining optimum metallurgical recovery. The philosophy of mill modernization/modification is generally driven by the desire to increase the mill capacity within the limits of the existing mill building. This need is facilitated by using large size flotation equipment and eliminating multiple parallel flotation circuits in order to minimize capital and operating costs. Conventional flotation machine development has paralleled this mill design philosophy. FLOTATION CELL DESIGN Since froth flotation has been the most widely used separation process for over half a century, one would expect that it would be possible to design and select flotation machines for specific applications based on scientific principles. But this has not been the case. Best judgment, experience and personal prejudice have played a key role in equipment selection. These factors, along with the difficulty of evaluating new concepts in commercial plants, has slowed progress in implementation and commercialization of innovative ideas and/or equipment. Conventional Flotation There have been no major technological advances in conventional flotation cell design in recent years. A recent flotation cell survey indicates that &apos;larger flotation cells are still the order of the day.”(1) A comprehensive review of design of flotation machines indicate that they have been mechanically redesigned and are generally simpler and easier to maintain and less expensive to manufacture. (2,3) The approximate chronological development of conventional cells from the 25 cubic foot cells to the 3000 cubic foot cells, which were recently installed at the Copperton concentrator of Utah Copper, is given in Table 1. Larger flotation cells are the obvious choice for new plants or plants looking for expansion because of the following reasons: • They have lower capital cost per unit volume • Installation costs are generally lower because fewer units require less space • Maintenance costs are lower because of fewer mechanisms • Power requirements (HP/ton dry feed) are generally lower • with increased flotation cell size as illustrated in Table 2 [Table 1. Conventional Flotation Cell Size Development Year Individual Cubic Cell Size, Feet 1925 25 1935 50 1960 100 1965 300 1970 500 1975 1,000 1980 1,500 1985 3,000]

Jan 1, 1989

By John R. Wright

This paper reviews the increased use of mechanization in order to develop lateral headings efficiently and economically. Particular emphasis is placed on the role of the Electric-Hydraulic Drill Jumbo in achieving this goal. Also, the use of modified mining equipment to suit various operating conditions is discussed.

Jan 1, 1981

By Gordon J. Hughes

The ldaho Cobalt Belt represents a unique geologic environment containing some of the largest known reserves of cobalt in the United States. Stratabound cobalt-copper-gold deposits formed within a sedimentary basin that was generated by the rifting of an Archean cratonic block. Host rocks for these deposits are the Early to Middle Proterozoic Yellowjacket Formation comprising a suite of clastic sediments, volcaniclastics, and mafic tuffs that accumulated in the intracratonic rift basin about 1.7 b.y. ago. Rifting was probably initiated during a regional heating and doming event that may date back to 1.8 b.y. ago. During this time, other rift basins were likely to have formed in the region. They probably represent the precursors of a much larger depositional environment having characteristics of an Atlantic- type or passive continental margin where younger formations of the Belt Supergroup were deposited. The Yellowjacket Formation has been subdivided in the Idaho Cobalt Belt into three genetic units representing various subenvironments of a deepwater clastic fan complex. A northwest- trending deep-basin structural trough accumulated fine-grained muddy sediments that were periodically interrupted by distal turbidites of the subaqueous fans. Subsequent progradation caused the deposition of coarser-grained clastics of the more proximal portions of the fan complexes. Submarine fan lobes were built across northwest-trending tectonically active basin growth faults. These in-basin structures caused a great deal of penecontemporaneous deformation within the Yellowjacket sequence. Northeast-trending fault zones formed an orthogonal set of fractures that controlled the shape and size of sub-basins, and were also an influence on lateral migration of dominantly fine-grained clastic material. The eruption of mafic tuffs at about 1.7 b.y. ago added a new component to the Yellowjacket sedimentary sequence. Around the Blackbird mine area these tuffs commonly occur either near the base or within some of the sandier sequences. Since most of the sand influxes were largely controlled by basinal tectonism, the tuffs were probably erupted during tectonically active periods of basin development. The dynamic nature of the sedimentary environment probably caused much of the tuffaceous component to be mixed with other clastics and even resedimented as volcaniclastic material. In time, the change to a higher energy sedimentation regime resulted in such a dramatic clastic dilution of the tuffs that they could not survive in the areas of the vents, and, if present, they must have been distributed elsewhere in the basin.

Jan 1, 2013

By P. D. Rao

Although phosphorus is a very important biogenic element, its concentration in coal is generally low. Phosphorus concentrations typically range from 0.001 % to 0.229% in raw coals of the contiguous 48 states. Some Alaskan coals in the Cook Inlet region contain horizons unusually high in phosphorus. A foot by foot analysis of deep drill core, containing 70 ft. of sub bituminous &apos;C&apos; coal from the Beluga coal field, Alaska, showed certain increments contained as high as 17.03% P2O5 in the coal ash; 1.01 % P on a moisture-free coal basis. Crandallite has been identified by electron microprobe analyses as a phosphorus numeral in these coals. The authors could quantify calcium, barium, strontium and phosphorus concentrations from the coal attributable to crandallite. These high phosphorus coals provided a unique opportunity to study the association of phosphorus in coals using chemical fractionation for exchangeable cations and acid extractable elements. Since the source of high phosphorous horizons in Cook Inlet coals is attributed to volcanic ash, it is suggested that the profiles of acid extractable phosphorous concentration may be useful for coal seam correlations.

Jan 1, 1992

By M. Moats, I. E. Paschalidou, K. Awuah-Offei

Tellurium (Te) is a rare metalloid that is predominantly produced from the treatment of anode slimes formed during copper (Cu) electrolytic refining. The US Government lists Te as one of the 50 critical minerals, partly, because of its use in thin-film photovoltaic (PV) technology. Given policy initiatives to increase Te production, it is important to evaluate the life-cycle environmental impacts of Te recovery as a by-product of Cu processing. The literature contains a few specific life cycle assessment (LCA) studies of groups of metals that include Te without proper regard to impacts per life-cycle stage of Te production or the effect of allocation on the results. This study builds an LCA model of the production system of Te from anode slimes treatment to evaluate the effect of allocation on life-cycle impacts. We build life cycle inventories using data from the Ecoinvent v3.7.1 database, literature, and engineering calculations and allocate impacts in proportion to products’ mass and economic value. The results show that economic value-based allocation yields greater impacts than mass-based allocation indicating the significant effect of the allocation approach on life-cycle impact estimates.

Feb 1, 2023

By William G. Pariseau, Mark K. Larson, Heather E. Lawson

Rational design based on engineering fundamentals is essential for the layout of safe, stable shafts and tunnels. Shafts and tunnels including winzes, raises, adits, and crosscuts are lifelines to the underground and must be secure. The contribution of this paper describes a significant extension in existing software previously developed for five important design problems in strata-bound mines such as coal, trona, salt, potash, and some large, lead-zinc mines. This extension in software allows analysis to proceed in three easy steps: (1) preparation of a strata properties file, (2) generation of the finite element model, a mesh, and (3) finite element program execution. Circular, elliptical, and rectangular shaft sections are available for a single shaft, twin shafts, and shafts in a row. Spacing of twin shafts and shafts in a row is a free parameter (pillar width). Tunnel shapes are the same as shafts but include the conventional arched back section. Dipping strata of variable thickness, depth and orientation relative to the excavation of choice are allowed. The analyses are three-dimensional. An elastic-plastic material model based on associated rules of flow and an N-type yield condition for isotropic, transversely isotropic, or orthotropic rock are used for all strata. Example analyses from several hardrock mines are provided to illustrate the three-step process including mesh plotting and plotting of selected results. The goal of this software is to advance mine design technology for improved miner health and safety.

By Alexander N. Winchell

"The wash ore area on the Mesabi iron range covers a regionof the iron bearing formation extending from Grand Rapids on the west to the Hibbing district, about forty miles eastward. Not all of the developed ore bodies are of wash structure; some are of such grades that they can be shipped direct as merchants able ore. It is safe to say, however, that 65 per cent of the ore is of a possible wash structure and of too high a silica content to be classified as merchantable ore. The increase in the number of washing plants completed each year on the western Mesabi shows that ,the product must be of a structure desirable for furnace operation. The following is a list of plants which were . in operation, under construction, or with plans completed, at the end of 1918:"

Jan 1, 1920

By P. D. Rao

Chemical and physical properties of typical low-rank coal (LRC) ash are significantly different than bituminous coal ash. With the exception of extraneous ash, which is incorporated during mining or is due to ash partings within or between coal seams, LRC ash consists primarily of inherent ash that is bonded into the coal&apos;s organic matrix or finely disseminated mineral matter. This paper reviews the nature of LRC ash, both inherent and extraneous, and how this impacts the prospects of washing and utilizing LRCs. A literature review, as well as washability data, proximate and ultimate analyses and ash analysis of 25 Alaskan LRC seams are used as a basis for this discussion. The authors&apos; recent research into the nature and distribution of phosphorous in an Alaskan LRC is also discussed

Jan 1, 1997

By C. A. Born

AMAX Inc. climax&apos;s mine-mill complex at Climax, Colorado is best known for its molybdenite production: 50,000 TPY of molybdenite flotation concentrate (95% MoS2) from mill heads containing 0.35% molybdenite. Less recognized are the byproducts that are concentrated from the tails generated in the rougher flotation circuit (see Figure 1). Climax recovers a heavy mineral concentrate by passing the rougher tailings from molybdenite flotation over Humphrey spirals (Figure 2a). This concentrate is floated using xanthate at pH 4 to remove sulfides, principally pyrite. The tails from the pyrite float are then cleaned of quartz, feldspar and light minerals by tabling (Figure 2b). Amine flotation follows at pH 1.5 and 75°C to float monazite (Figure 2c). The present circuit at Climax dries the monazite flotation tailings and utilizes high intensity cross-belt magnetic separation Figure 2d) to generate a high grade wolframite concentrate and a low-grade cassiterite product, both of which are contaminated with the mineral brannerite, (UO, TiO, UO2)TiO3. The uranium specifications have recently become difficult to meet due to the increasing percentage of brannerite reporting in the mill feed. A plant is being built utilizing hot sulfuric acid and sodium chlorate to leach this uranium from the monazite flotation tailings prior to their being fed to the wolframite- cassiterite magnetic separators. This modification is the subject of our paper.

Jan 1, 1975

By H. Reed

The precious metal mining industry in Nevada handles and generates a certain amount of hazardous materials and waste on a regular basis. These products range from processing material additives to wastes from laboratory testing, heap leaching, and hydrocarbon treatment and disposal. The volume of materials and wastes is dependent upon the amount of ore processed. Handling, treatment and disposal is dependent on the type of material handled and the waste generated. Owing to the health and safety concerns and due to the existing regulations that control handling and disposal of hazardous materials and wastes, the mining industry is obligated to comply with all applicable requirements for proper handling of these products. Plus, in an effort to minimize any impacts from this effort, the industry is continually looking for alternative methods to accomplish these requirements and to also minimize costs. This paper will discuss the general, and in some cases the specific conditions, by which the industry is coping with the issue and efforts to minimize any impacts from handling, treatment and disposal for hazardous materials and wastes. The subject of compliance with the Toxic Release Inventory (TRI) requirements and bio-treatment of wastes and other technologies will be discussed.

Jan 1, 2001

By Andrew H. Merritt

INTRODUCTION The prediction of the engineering behavior of a rock mass depends upon the systematic analyses of the results of an exploration program, and upon the recognition of the significant rock properties in the early stages of excavation. The variations in rock properties in different geologic terrains and the state of the geotechnical art preclude complete success in the former case, and we therefore must rely heavily on the experience gained in the latter phase. The geotechnical information obtained from these two phases is only of value to the design engineer when applied to the rock behavior during excavation and subsequent plant operation. Pertinent questions which must be answered include: how does the joint orientation and frequency effect tunnel support and overall cavern stability; how does the depth of surficial soil or weathering effect foundations or slope stability for portal cuts; are there permeable zones within the rock mass that could lead to leakage problems around penstocks and is the material in these zones soluble or likely to pipe in the long term; and does the proposed engineering structure fit the terrain, or will it inevitably lead to problems requiring extensive remedial treatment. During the early stages of construction there are two types of geotechnical information required; actual rock behavior with respect to the original design assumptions,

Jan 1, 1997

By Sarah Vest, Richard Sherman, Leo Martin

In 1988 a major exploration program was undertaken to determine the characteristics of the rock and soil for a 7.6 m diameter sea outfall tunnel beneath Boston Harbor out into Massachusetts Bay. The diffuser discharge location had been mandated by the EPA to a 10 sq. km area of seafloor connected to the proposed Deer Island Treatment Facility by a 14.5 km tunnel corridor. Geophysical surveys, deep rock borings, and laboratory testing, provided the information for the conceptual design. The program identified the range in material types and parameters to prove feasibility of a TBM driven tunnel and to locate the optimum alignment and depth.

Jan 1, 1991

By M. Paventi, M. J. Scoble, B. B. Mohanty

There is no straightforward and systematic method for adequately measuring blast damage in on-going mining operations. This paper considers various techniques available for the measurement of blast damage, making particular reference to recent underground hardrock mine studies. This paper concludes by indicating the importance of understanding and accounting for geology and emphasizes the need for a robust damage-audit procedure.

Jan 1, 1998

By J. C. Johnson

The problem of estimating pillar capacity in coal mines has motivated development of a variety of empirical equations. Most of these equations have arisen from experience and a very limited set of measurements that have, necessarily, been focused on particular regions or coal fields. Their applicability is often limited to a specific range of pillar sizes. This is of particular concern in the design of large gateroad pillars and small barrier pillars between panels. The result has been a variety of equations and equation coefficients that can calculate load estimates to size pillars. Inclusion of these equations in more sophisticated loading models, such as boundary element methods (e.g. LaModel and MULSIM) has been hampered by absence of a function that describes specific variation of coal strength within the pillar. A singular exception, to our knowledge, is a function corresponding to the Bieniawski pillar strength equation. Because of this, it is the only coal strength criteria inherently available in most boundary element models. This paper presents a general method for deriving local coal strength, as a function of distance from the pillar rib, for an arbitrary pillar strength equation. Integration of this function provides the strength of pillar regions, or cells, needed for boundary element models. The method is demonstrated for the Bieniawski, Maleki and Holland-Gaddy equations. The Maleki and Holland-Gaddy equations contrast strongly with Bieniawski as strengths are extrapolated to large pillars and barriers. This development provides a tool for incorporating any of the proposed empirical equations into a boundary element model, thereby allowing the analyst to choose the most appropriate equation for a particular region, coal seam and/or pillar size.

Feb 23, 2014

By A. Suarez, M. Menendez, M. R. Gent, P. Riesgo

"Recent requirements to reduce thermal coal plant emissions, and ultrafine coal's tendency to produce these emissions due to its typically high ash and moisture contents have limited the use of ultrafine coal. Ultrafine coal in beneficiation plants are usually either disposed of in tailing ponds at a loss in combustible material or disposed of by blending with coarser higher-grade products, resulting in a reduction in marketed product quality. A study of the options for processing ultrafine coal, consisting of < 200 µm hydrocyclone overflow, with 38.8 percent ash content is presented here. Ultrafine coal was processed based on 200-µm sieve bend and 10-µm hydrocyclone classifications, enhanced gravity separation (EGS) and froth flotation concentration as well as combinations of these. Yield, combustible material recovery (CMR) and product humidity were evaluated as test results.Depending on the processing applied, product ash content could be reduced up to 49.7 percent, and up to 95.8 percent CMR of the actual run of mill feed could be attained. All of the processing options analyzed could reduce produced thermal electric plant emissions due to ash and moisture from 22 to 38 percent of the actual unprocessed ultrafine coal product.Froth flotation was found to be the optimal process, yielding a product with the lowest ash content attained of 19.5 percent and CMR of 92.3 percent. Being the most versatile of the processes evaluated, it is capable of producing coal with varied ash contents but is subject to potential variations in coal flotability. The most complicated of the processing options, a combined sieve bend recovery of the > 200 µm fraction and EGS processing of the 10 to 200 µm fraction was found to be the next best option, attaining a combined 90.1 percent CMR and 25.0 percent ash content. IntroductionMunicipal, regional and national objectives to reduce fossil fuel combustion emissions and their effects on air quality and global weather changes are affecting thermal electric plant operations. Plans and regulations such as President Obama's Clean Power Plan (U.S. Environmental Protection Agency, 2015), the European Directive 2010/75/EU (European Commission, 2010) and China’s proposed Enhanced Actions on Climate Change (Wei, 2015) are of major significance to thermal electric plant operations. Although thermal plant efficiencies depend in large part on the losses of heat by plant components, the ash and humidity contents of thermal coal invariably reduce plant efficiencies and increase emissions of carbon dioxide (CO2), nitrogen oxides (NOx) and dust.Any noncombustible material present in thermal coal will result in higher CO2 emissions per unit of energy produced. Since no particle emission control can be totally effective, it is to be anticipated that any reduction in coal ash content will also result in reduced particle emissions. Kurose, Ikeda and Makino (2001) reported that NOx emissions also increase with coal ash content. The effect of coal moisture content during combustion is complex. Kurose, Ikeda and Makino (2001) showed that an increase in coal moisture content significantly reduces thermal NOx to total NOx production, and Bosoaga et al. (2006) showed that it tends to reduce NOx emissions. Since the humidity, pyrite and ash content of thermal coals directly affect thermal electric plant efficiencies and emissions, minimizing these factors should facilitate, at least in part, compliance with thermal electric plant emission limits. This, in turn, would affect the specifications and prices of the coal preparation plant products."

Jan 1, 2016

By MATTHEW HART, THOMAS BAMFORD, Kamran Esmaeili, MICHAL KOWALCZYK, FILIP MEDINAC

Improved haul-road conditions can have a positive impact on mine operations, resulting in heightened safety, productivity gains, longer tire life and lower maintenance costs. For these reasons, a monitoring program is required to ensure the operational efficiency of the haul roads. Currently, at Bald Mountain Mine, monthly site severity studies, ad hoc inspections by frontline supervisors or operator feedback reporting are used to assess road conditions. These methods are subjective and provide low temporal resolution data. This case study presents novel unmanned aerial vehicle (UAV) technologies, applied on a critical section of haul road at Bald Mountain, to showcase the potential for monitoring haul roads. The results show that orthophotos and digital elevation models can be used to assess the road smoothness condition and to check the road design compliance. Moreover, the aerial mapping allows detection of surface water, rock spillage and potholes on the road that can be quickly repaired/removed by the dedicated road maintenance team.

By A. G. Journel

The indicator random function formalism allows a common coding of hard numerical data, constraint intervals, and soft qualitative information as prior probability distributions. The soft kriging algorithm allows interpolating these priors into posterior probability distributions of the unknown. The curse of ?negative kriged grades? is solved. The consideration of additional soft information, whenever deemed necessary, becomes possible within the framework of well-proven kriging techniques.

Jan 1, 1986