Search Documents

By W. R. SHAHAN, W. R. Reed, J. P. Rider

Roof bolter operators may be exposed to high respirable dust concentrations on continuous miner sections with blowing face ventilation when bolting is performed downwind of the continuous miner. One solution to reduce the high respirable dust concentrations is to use a canopy air curtain (CAC) to deliver clean air from a filtered blower fan directly to the bolter operators under the canopies. The influence of CAC installation on the airflow and dust dispersion around the location of the roof bolter operator can be evaluated by using computational fluid dynamics (CFD). 

By Noel C. Joughin, Orrie Fenn, Brian E. Protheroe

Work has shown that the use of high-pressure water jets enhances the performance of mechanical cutting in very hard rock. To assess the potential of this approach for use in conjunction with free rolling cutters, a series of tests has been conducted using both disc and button type cutters, to determine the relative effects, on cutter performance, of variations in relevant jet and cutting parameters. In these tests it was found that water jet assistance can result in reductions in the forces on a free rolling cutter typically of the order of 40%.

Jan 1, 1985

By Richard P. Curtin, Madan M. Singh, Francis S. Kendorski

INTRODUCTION The use of roof and rock bolts to reinforce the strata is an established method of rock support in both underground and surface excavations. However, the need to drill a hole, extract the drill-rods, and then place the bolt is time-consuming and costly. This becomes even more significant if the bolting is repetitive and extensive as in coal mining. Though the main thrust of this development was directed towards coal mining, the basic concepts are also widely applicable to all excavations. The authors, therefore, feel that this innovation should be of interest in rapid excavation and in tunneling. In the case of coal mining, it has been established from past statistics that the roof-bolting operation is the most hazardous activity. This is primarily because of the operator being exposed to unsupported ground. It is evident that remote installation of roof bolts would markedly improve the safety of the operation, if accomplished more readily with self-drilling bolts rather than the conventional two-step variety operation. Thus, in addition to increasing productivity, this development can be considered to be a milestone towards further improvements. The objective of this program was to establish the technical and economic feasibility of self-drilling roof bolts for use in coal mines. It might be clarified at the outset that this work was, therefore, directed primarily at showing that workable self-drilling bolts with less cost can be developed, which could be effectively used in mines. It was not to fabricate a production model bolt.

Jan 1, 1979

By Thomas J. Regan

The first stage of the Massachusetts Bay Transportation Authority's Red Line Extension Northwest, is a two-track rapid transit extension from Harvard Square in Cambridge, through three stations, to the Alewife Station/Garage complex in North Cambridge. The extension, about 5.0 km. (3.1 miles) in length, is entirely in tunnel, with the Alewife Station/Garage complex and adjacent line sections of tunnel constructed by cut-and-cover methods. The Station/Garage complex, just west of Alewife Brook Parkway, is in an area underlain by deep deposits of very soft highly sensitive clays. It is proposed to construct the station and adjacent tunnel sections by the slurry trench method, using the slurry wall as the permanent structural wall of the station and tunnel. The unusual nature of the underlying clay and its very high sensitivity raised questions concerning the feasibility of the proposed construction. Since research failed to reveal any construction precedent for the specific conditions encountered, a test section was undertaken to determine construction problems, resolve uncertainties, and to establish acceptable parameters for the construction of the slurry walls. PROJECT ORGANIZATION Sverdrup & Parcel as tunnel and transit systems consultant for the Red Line Extension-Davis Square to Alewife had overall responsibility for determining program objectives, project management and test implementation.

Jan 1, 1979

By C. RAMADINI, F. NURJAMAN, A. SHOFI, B. SUHARNO

Nickel demand is increasing along with the rising need for stainless steel and other alloy steel/iron. The small addition of nickel in such materials can improve impact strength, ductility and corrosion resistance. Nickel is generally obtained from nickel sulfide ores (nickel associated with sulfur) and nickel laterite ores (nickel associated with iron and magnesium silicate). Almost 60 percent of nickel is now produced from sulfide ores, despite its existence in sulfide ores being less than in laterite ores. However, the depletion of sulfide ore reserves makes the mastery of nickel laterite ore processing of important and immediate concern. Selective reduction followed by magnetic separation has been in development in lateritic nickel ore processing to overcome the issues of high energy consumption and pollution associated with conventional pyrometallurgy methods such as blast furnace and rotary kiln electric arc furnace (RKEF).

By Carl E. Schubert

The application of geophysical technology relative to the exploration, planning, and operation of coal mines is expanding. This is due to the trend of the industry to increase the size of operations, use of mechanized equipment and mining of more difficult coals, where unforeseen conditions can affect mine profitability. Coal is a good geophysical target because of its lower density, higher electrical resistivity, lower seismic wave velocity, and lower magnetic susceptibility in comparison to typical country rock. The more important techniques are well logging, high resolution seismic reflection, seam wave velocity, and radar. These methods can be used to map coal horizons, determine the physical properties of the coal, and identify mining hazards. The methods are not a pancrea however. Their use should be based on a careful assessment of their expected success and cost benefit analysis in comparison with conventional technology, primarily drilling, which none of the techniques presented should entirely replace. In general, the level of technology developed for geophysics surpasses their current level of application to coal problems. In some cases, identifying hazards in advance of mining using seam wave seismic in particular, the state of the art has been developed in Europe and is awaiting fruitful application in the United States.

Jan 1, 1982

By Jeffrey L. Zelms

There is no known, practical substitute for lead in the automobiles, communications systems, medical equipment and computers that Americans use every day. However, there are many who say lead should be stopped at its source -- banned. As America's largest lead producer, The Doe Run Company has ralized that it must do more than mine and reclaim lead efficiently and safely. It must also earn the public's consent to operate if it is to continue to be a viable business. LEAD - THE BRILLIANT PERFORMER: REFURBISHING AN IMAGE It's been an embarrassingly long time since I was a college student. However, I remember there was no course at the University of Missouri's School of Mines and Metallurgy that had anything to do with the public relations aspects of mining or, put another way, the politicization of mining. It's been an embarrassingly long time since I was a college student. However, I remember there was no course at the University of Missouri's School of Mines and Metallurgy that had anything to do with the public relations aspects of mining or, put another way, the politicization of mining. I haven’t perused the course catalog for Penn State’s College of Earth and Minerals Sciences. But I strongly suspect I wouldn’t find such a course there today, either. A statement by the chairman of one of the country’s largest chemical companies leads to the point I want to make. He described his business this way. He said, “We’re a public affairs company that just happens to produce and market chemicals.” Like chemicals, minerals and mining are politicized today. To the extent that we don’t understand that reality, we don’t understand that reality – and act on it – we’re less likely to survive in this business. Some of you may well be saying to yourselves, “This guy Zelms is an alarmist.” That’s fair enough. Because it is absolutely true that there’s n o known, practical substitute for lead today. And it’s also absolutely true that, knowingly or not, Americans use lead everyday. It’s in our automobile batteries. It’s an integral part of communications systems. High tech (and low tech) medical equipment contains lead. And lead is an essential component of computer and TV screens. But even with all these uses, lead has a negative image today. An image so negative that its very existence is threatened. If you doubt that, consider these two statements made in 1989. Statement one. “It is probably reasonable to argue that exposure is the single most important and critical environmental health problem in the U.S., and possibly also the world…” Statement number two. “Many of the uses of lead should be terminated. We need to go back to the ultimate source: that is, taking lead out of the ground and putting it into the product stream and we need to turn it off at the ultimate source. Not the approximate lead in gasoline, or lead in air, or lead in food. Go right back to the source and start cranking it down." (End quote.) Those are what I call strong statements. And they weren’t made by some celebrity spokesperson for the environment like Meryl Streep. Both these statements were made by Dr. Ellen Silbergeld, whose long list of professional and academic credentials includes: o Adjunct professor and research scientist at the University of Maryland Medical School and Johns Hopkins: o Chief toxic scientist and director of the Toxic Chemicals Program of the Environmental Defense fund; o and President of the Society for Occupational and Environmental Health. If Dr. Silbergeld were the only person making these kinds of statements, it would be one thing. But she’s not a voice in the wilderness, by any means. Also for those of you who say, well since there’s no known substitute for lead, how on earth could it be banned. I refer you to a number of bills before Congress that would permit the EPA to ban any product if it is determined that its

Jan 1, 1992

By J. A. Rusnak, K. M. Mohamed, M. A. Van Dyke, M. M. Sears, G. Rashed

"Researchers from the National Institute for Occupational Safety and Health (NIOSH) recently developed a coal-mass model to realistically simulate the deformation and loading behaviors of the ribs of coal pillars in underground coal mines. The scale-dependent properties (stiffness and strength) of coal material were considered in the coal-mass model. In this paper the orientation of face cleat with respect to driving direction was integrated in the coal-mass model. The controlling parameters (dimensionless coal-mass scale and fracture strains) of the modified coal-mass model were calibrated using a published case study of coal pillar strength. Numerical models with wide ranges of controlling parameters were conducted to simulate the test pillar. The best match between the numerical modeling results and the measured stresses and deformations was achieved by using a coal-mass scale of 30 and fracture plastic shear and tensile strains of 3.25% and 0.325 %, respectively. INTRODUCTION The failure of coal pillar ribs by itself are a major hazard in underground coal mines. Furthermore, failing ribs can indirectly contribute to roof and floor instability by increasing opening widths across intersections and entryways. Over the past decade, rib failures have resulted in 12 fatalities, representing 28% of the ground-fall fatalities in U.S. underground coal mines. Mining depth has always played a very important role in assessing rib stability. Gauna and Mark (2010) completed an analysis of rib fatalities that occurred between 1996 and 2010. One of their most prominent and influential findings was the identification of a relationship among fatalities, depth, and mining height. Therefore, Coal rib stability will continue to be a challenge for future deeper mines in U.S. coal basins. In the past several decades, research efforts have focused on roof support. The current rib control practice in U.S. coal mines is to select rib bolts through a trial-and-error approach (Mohamed et al., 2015a). Rib failure incidents can be can be substantially reduced or even eliminated by adopting an engineering-based coal rib design approach. The factors affecting rib stability in coal mines are numerous and mutually dependent. These factors include but not limited to mining height and overburden depth, interburden thickness for multiple-seam mining, coal strength, cleat density, entry direction with respect to cleat orientation, existence or absence of partings in the coal, percentage of extracted roof and/or floor rock, density of rib bolt support (Mohamed et al., 2015a). Moreover, it is difficult to isolate the particular effect of a specific factor on the overall rib stability. Therefore, a reliable empirical rib design approach is not achievable because it requires a significant number of case histories to be collected in order to have a reasonable range of all of the critical parameters. However, numerical modeling can be a practical tool to assist with rib support design if the modeling is realistic, which can only be achieved through calibration and validation of the numerical model against field data."

Jan 1, 2018

By Wilbur I. Duvall

INTRODUCTION This chapter outlines some general principles and procedures that a rock mechanics engineer can use to arrive at a logical design for the size, shape, and spacings of underground openings in various types of com¬petent rock formations. Rock formations can be clas¬sified into six major categories which are useful for design purposes, provided the necessary input data are available regarding the geology of the site, the physical properties of the rock, the in-situ stress field in the rock, and the general geometry of the underground openings. The US Bureau of Mines (USBM) developed a rock classification system based upon these concepts and found it to be useful for design purposes (Obert, et al., 1960; Obert and Duvall, 1967). This classification sys¬tem is given in Table 1; however, an extra column has been added to the original classification to indicate the appropriate design techniques for each rock class. In this classification system, two main classes of rock are considered: competent rock and incompetent rock. Competent Rock Competent rock is any rock which, because of its mechanical and geological characteristics, is capable of sustaining underground openings without the aid of any structural support except that provided by unmined rock in the form of pillars and side walls, etc. Roof bolts and small random props which support only local loose rock are not considered structural supports. Competent rock is further subdivided into three ad¬ditional categories-massive, laminated, and jointed¬ which are defined as follows: Massive Rock: Massive rock is a rock formation where the spacing between mechanical defects such as joints, partings, or faults is equal to or greater than the critical dimensions of openings, or where the strength of the bond across these mechanical defects is com¬parable to the rock strength. Laminated Rock: Laminated rock is a rock forma¬tion divided by approximately parallel planes of weak¬ness into lamina whose thicknesses are small compared to critical dimensions of openings and where the bond between the lamina is weak compared to the rock strength. Elastic Rock-This is rock whose physical proper¬ties will permit the use of elastic theory to predict strains and displacements from applied stresses. Inelastic Rock-This is rock whose physical proper¬ties are such that strains and displacements are a strong function of time as well as applied stress. Incompetent Rock Incompetent rock is any rock which, because of its mechanical and geologic characteristics, is not capable of sustaining underground openings without the aid of additional structural support in the form of linings, steel sets, or systems of props. This classification system for rock depends not only on the mechanical and geologic characteristics of the rock but on the size of openings and their depth be¬low the surface. For example, many competent rocks at shallow depths for small stress fields could become inelastic rock at greater depths and larger stress fields, or competent massive rock for small openings could be¬come laminated or jointed rock for larger openings. Thus, to classify rock for design purposes requires a knowledge of the geologic properties of the rock mass, the physical properties of the rock, the general size of the openings to be mined, and the average range of the in-situ stress field to be encountered. To design underground openings and structures in rock, it is necessary to use criteria of failure for rock under various stress conditions, and to use safety factors to allow for differences between laboratory and in-situ strength properties of rock and to account for errors in¬troduced by the various assumptions made in the design process. Criteria of failure based on maximum stresses have been found to give reliable results in practice. Thus, it is assumed that rock will fail in tension when the tensile stress exceeds the tensile strength of the rock as determined by a standard modulus of rupture test on samples of rock core. If the tensile stresses in rock are small, then it is assumed that the rock will fail at a value of compressive stress equal to the compressive strength of the rock as determined by standard uniaxial compres¬sive strength tests on samples of rock core. These fail¬ure criteria, when used with appropriate safety factors, can be expressed as:

Jan 1, 1982

By Carl G. Bock

INTRODUCTION Rapid transit systems involving near surface tunneling in hard rock are becoming more numerous, especially along the northeast corridor of the East Coast. Tunneled systems are under construction in Washington, D.C. and are being planned for Atlanta, Buffalo and Baltimore. Near surface tunneling is defined for this paper as being that in which the crown is 100 feet or less below ground surface. For Rosslyn Station, the total cover ranged from 52 to 70 feet. The rock cover, however, ranged from 40 to 50 feet which is slightly less than the station height and about two-thirds of its width. Rosslyn Station (Fig. 1) is the only station excavated completely in hard rock in the Virginia portion of the 98.5 mile Washington Metropolitan Area Transit Authority's (WMATA) rapid transit system. The station site, oriented in a north-south direction beneath a main thoroughfare and flanked by multistory office buildings, was fixed by the need to serve a dense population center at a specific location and geologic conditions were a secondary consideration in siting. There was no previous underground rock excavation in the Washington Metropolitan Area of the size and scope of Rosslyn Station that offered a practical case history guide to the geologic conditions and excavation problems to be encountered. GEOLOGY The regional geology of the Washington Metropolitan Area is divided into two physiographic provinces by the northeast trending Fall Line (Fig. 2). Northwest of this boundary is the Piedmont Province

Jan 1, 1974

By Elwyn King, Donald J. Dodds

"...Unfortunately, the research activities in soil mechanics had one undesirable psychological effect. They diverted the attention of many investigators and teachers from the manifold limitations imposed by nature on the application of mathematics to problems in earthwork engineering. As a consequence, more and more emphasis has been placed on refinements in sampling and testing and on those very few problems that can be solved with accuracy. Yet accurate solutions can be obtained only if the soil strata are practically homogeneous and continuous...." This statement about soil mechanics was made by Karl Terzaghi, thirty years ago and applies to a greater degree today to the infant science of rock mechanics. More uncontrolled variables are added to the already many existing in soil mechanics. Variables, such as Macro-discontinuity and in situ stress levels. In no other field of engineering are the problems as site oriented. Presently this site dependance demands the investigator or rock mechanics engineer to get his hands dirty rooting in the muck of a tunnel floor trying to properly install or readout test apparatus in a comprehensive site investigation. This paper discusses such a site investigation designed to determine the problems and solutions inherent in the driving of the Trans Koolau Tunnel. The paper will describe the various types of tests to be performed, how the results are to be used and the interrelation of the various tests themselves.

Jan 1, 1997

By K. K. Cheng, Z. M. Chen, A. L. Mular

INTRODUCTION Since the nineteen fifties, process engineers have been seriously concerned with process models for various purposes (1,2,3). Models serve as subroutines to mathematical flowsheets which simulate circuits of interest. Simulators can serve to increase process know- ledge, assess circuit performance, investigate flowsheet modifications, evaluate new flowsheets, perform off-line optimization, and compare alternative control strategies. This chapter describes a methodology to develop a simulator of a bulk Cu-Mo circuit comprised of roughers, scavengers and 3 stages of cleaning. The simulator was employed to evaluate the influence of water addition at circuit points and to estimate the optimal number of cells for each stage in the circuit. DESCRIPTION OF CIRCUIT Figure 1 is a flowsheet of the Brenda Mines Ltd. (located near Peachland, B. C.) bulk Cu-Mo flotation circuit as simulated prior to an expansion/renovation which involved the installation of large, new flotation cells. Referring to the flowsheet, feed to rougher cells includes fresh feed, scavenger concentrate and 1st cleaner tailing. Rougher con, 1st cleaner (sect ion 2) con and 2nd cleaner tailing are fed to 1st cleaners (section 1). 1st cleaner (section 1) concentrate and 3rd cleaner tailing serve as 2nd cleaner feed, while 2nd cleaner concentrate is fed to the 3rd cleaners which produce a final bulk concentrate. Table 1 lists cell types and specifications important to the circuit. DEVELOPMENT OF MODELS To develop flotation cell models a systematic procedure was employed (4). This involves the selection of responses and factors, proposing models to be fitted, the acquisition of raw data, the statistical adjustment of raw data, fitting models to adjusted data and testing the adequacy of fitted functions. Responses and Factors Responses of interest included recoveries, concentrate grades and concentrate solids/water flow rates for each stage. Factors that influence these responses, such as reagent addition rates, air flow rates to cells, solids and water flow rates to stages and feed grades were not manipulated during the sampling period. Thus, the investigation was limited,

Jan 1, 1986

By Stephen G. Tough, Ted M. Noskiewicz

INTRODUCTION For many years, in Europe and in North America, pre-formed metallic and concrete segmental linings in tunnels have been used extensively as temporary and permanent ground support systems. In the United Kingdom the use of cast iron as a means of ground support in mining shafts dates from the first decade of the 19th century. Although at that time wood tubbing was extensively employed, cast iron was used in shafts at Wallsend and Percy Main collieries in the North East of England. The original form of cast iron tubbing consisted of cylinders which were lowered bodily into the pit and were built from the bottom up, but subsequently they were subdivided into segments which involved the making of vertical as well as horizontal joints. Principally, the practice of providing immediate pre-formed support developed because of the incompetent state of the surrounding ground and, although this still remains the over-riding consideration nowadays, several other factors are examined before finally deciding what type of lining to use. Other branches of sub-terranean technology such as tunnel thrusting or immersed tubes (both of which involve pre-formed linings) can provide alternative solutions to problems hitherto thought better solved by bored tunnelling methods. However, this paper will confine itself to those linings developed for the more traditional tunnelling methods. Usually the shape of segmentally lined tunnels is circular because this profile is the most suitable for bad ground and many tunnelling machines. This does not always lead to the most economic use of space within the tunnel and horseshoe or elliptical linings are sometimes used in suitable ground. The number of segments

Jan 1, 1974

By Jeremy Maurer, Duah Philip, Awuah-Offei Kwame, Donya Otarod

Land use impact assessment for mining is time- consuming and expensive. Because of mining’s impact on biodiversity, land use assessment methods that evaluate biodiversity are important for mining land use impact assessments. Remote sensing, in particular satellite multispectral sensing platforms such as Sentinel‑2 and the Landsat mission series, have been used to assess and quantify biodiversity through proxy variables such as NDVI (Peña-Lara et al., 2022). The objective of this paper is to present results of a comparative study of land use and biodiversity based on multispectral satellite observations and production data from copper and cobalt mining in the Democratic Republic of Congo. We quantify the relationship between different spectral bands and vegetative indices and the production data provided by the mining companies and measure correlations. The results suggest that remote sensing could be a cost- effective means of assessing biodiversity impacts of mining.

Feb 1, 2025

By P. A. Korpi

In March of 1978 the first set of Angular Spiral Liners utilized in grate discharge ball mills for wet grinding was put into service in the San Flanuel Concentrator of Flagma Copper Company. The use of these liners has decreased grinding media consumption by 19.2% and grinding energy consumption by 15.8%. In addition a 1.1% increase in grinding throughput is being realized through the use of the system. This paper describes the Angular Spiral Lining System and reviews the test program at the San Manuel Arizona Concentrator. Operating parameters are discussed in addition to the current testing program to futher optimize the system.

Jan 1, 1982

By EREN KOMURLUR, ATILA GURHAN CELIK, IBRAHIM GUNES

In this study, laboratory and site studies were performed to investigate the usability of a new insertion apparatus designed for the split-set type of friction bolts. The new apparatus decreases the friction during the bolt insertion by a temporary diametric compression of the split tubes. According to the results, the new precompression apparatus was found to be advantageous in terms of the insertion practicality and prevention of the buckling problem. By allowing increases in the ratio of bolt diameter to drill-hole diameter, the new apparatus was found to supply relatively high normal stresses and friction capacity in drill holes after opening its clamping mechanism.

By J. M. Goris

The U.S. Bureau of Mines, in cooperation with the Homestake Mining Co., and the University of Utah, is conducting a field demonstration to evaluate the behavior of rock masses supported with cable bolts. One of two rock masses being studied is supported with both conventional and birdcage cables. This rock mass is located between the 6500 and 6650 levels of the 45-4BN stope. 21 ledge. The second rock mass is the hanging wall of the D-limb stope between the 3500 and 3650 levels near the Ross Shaft and is supported with conventional cables. The primary objectives of the project are to monitor the behavior of the two rock masses during mining using extensometers and cable support strain gauges, after which the rock will be modeled using the finite-element code UTAH III. Field data will be used to verify the modeling. In addition. a comparison between the effectiveness of conventional and birdcage cables will be made.

Jan 1, 1991

By C. Y. Kao, Roger Y. Cheng, C. S. Hsieh

The mushroom-shaped Minghu power cavern located in central Taiwan is 21.2 m (W) by 40.5 m (H) by 127.2 m (L) and is designed to house 4 units of power generating-pumping equipment with a total capacity of 1,000 MW. This paper presents an introduction to the geological conditions at the cavern site; the rock mechanical tests undertaken; the design approach adopted; the construction method and sequence followed; and the instrumentation provided in the roof arch to monitor the behavior of the surrounding rocks. The measured data collected from the embedded instruments will be compared with those obtained from theoretical analyses and presented in this paper. Several technical problems encountered during the construction stage are covered and the solutions of these problems are also described therein.

Jan 1, 1983

By E. J. Beckman, R. M. Enick, C. Shi

A novel liquid-liquid separation for the recovery of free or liberated gold from mixtures of fine particles was evaluated. Two inexpensive and environmentally benign fluids were selected for the study, water and carbon dioxide. The separation, which is conducted at 295 K and at the vapor pressure of carbon dioxide (6.0 MPa), is based on differences in wettability between the precious metals and other minerals. Contact-angle results indicated that, in the presence of water and liquid CO2, gold is slightly hydrophobic. The addition of CO2-soluble fluoroalkyl thiols or f uoroetherthiols increased the hydrophobicity of gold exposed to water and CO2 to a greater extent than alkylthiols. Minerals, including quartz, pyrite and magnetite, were hydrophilic. During the separation, an aqueous slurry of fine mineral and gold particles was mixed with liquid carbon dioxide. Pure gold particles (-325 mesh) were found to agglomerate at the H2O-CO2 interface. The minerals tended to remain in the aqueous phase. Despite these promising preliminary results, very poor gold recoveries were obtained when applying the procedure to an Australian gravity concentrate. This was attributed to the native gold particles in the concentrate being either too large, agglomerated in slimes or coated with minerals. Although this particular application was unsuccessful, this water-CO2 biphase technique may be applicable for other separations that require the removal of very fine, hydrophobic particles from an aqueous slurry.

Jan 1, 2000

By Anand Kumar, Debasis Deb, A. K. Mishra, M V. N. S. PRASAD.

In the Adriyala project, shield-leg pressure data from all shields and shearer location with time stamp from a mechanized longwall face are monitored and recorded in a surface computer. The data contain random noise due to power failure, leakage of legs, bad sensor readings, and other maintenance or geomechanical problems. An algorithm has been developed to detect mining cycle parameters such as setting and final pressures and duration of the cycle from these data for the analysis of periodic roof weighting phenomena. The intensities and persistence of periodic roof weighting are vital information for mine management to make judicious decisions on longwall operation.