Search Documents

By R. H. Snow

Although industrial size reduction methods have an energy efficiency of only about 1 percent, methods of size reduction have not changed much for many years. One reason for slow progress has been the oversimple viewpoint that a single law should exist to relate size reduction to energy input. Modern simulation methods decompose the grinding process into a grinding rate function (selection function) and a breakage function. The breakage function is difficult to measure, and it usually requires tracers if it is determined from milling experiments. Prediction of breakage functions from basic principles is one objective of this paper. In this study we focus attention not on the gross energy input to the experiment, but on the spatial distribution of stress energy within the particle. We are led to this viewpoint by experimental observations of a few previous investigators (Bergstrom2, Rumpf3, Axelson4) and our own observations. Oka and Hiramatsu recently used their calculations of stress within particles for prediction of breakage, but again they tried to correlate the size of the fragments with the total stress energy, rather than the approach we propose. We assume that the stress energy is stored in the interior of the particle as the load is increased, until the particle breaks. We assume that each element of the particle breaks into fragments of a mean size that depends on the locally-stored stress energy. The size distribution of fragments is the computed from maps of the stress-

Jan 1, 1972

By Henning R. Norbom

Lime has been produced for many centuries. The simple pot kiln was one of the first devices used in this process. It was constructed of stone often on the side of a hill to reduce construction efforts and provide easy access to the top for feeding of limestone. It was fired from below with wood and coal. The pot kiln was very small and operated on the batch principle. The kiln being cooled between each batch, the fuel consumption was horrendous. The lime quality was poor with perhaps only one half of a batch being lime of suitable quality. Of the remaining half one part would be over burned and another part underburned. For centuries the lime burning technique was improved at a barely recognizable rate. One of the first major steps forward was the introduction of the continuous process vertical lime kiln. Although at first crudely constructed, the kiln had a refractory lining. It was charged with alternate layers of limestone and solid fuel usually in the form of coke. Continuous mode of operation, larger unit size and better heat distribution resulted in greatly improved fuel economy. However, quality of lime produced still left much to be desired. One problem was contamination by ashes from solid fuel.

Jan 1, 1978

By Donald E. Hendrickson

A new prinicple of side dumping front end loading for underground mucking machines has completely changed the concept of underground loading and haulage equipment arrangement both in production and development work loading. Versatility and adaptability of this type of machine permits combinations with a broad range of haulage means not possible with -conventional overhead loaders. Steel "armored" conveyors serving this type of loader are replacing conventional rail mounted car haulage to give a continuous loading operation and effect important economics of reduced manpower, faster loading rates and fewer working areas for a required production. First used in Germany this easy to control and highly efficient means of placing rock from the muck pile on or into haulage means has advanced the art of underground rock loading more in the past three years than any other advancement since the first successful small crawler mounted air powered loader was introduced in 1954. Bucket type loaders with a relative new side dump principle are gaining in popularity for underground loading. They are replacing conventional overhead loaders in present applications and becoming first choice in new ones. Primarily for hard rock development and production loading they are also widely used in production loading of coal and other soft materials. This discussion briefly traces the historical development of hard rock underground loaders to the new side dump type and its present population. In more detail various applications, loading techniques and the advantages of operation, production and economy with the side dumper in hard rock loading will be dealt with.

Jan 1, 1966

By Brendan Demich, MAHIYAR F. NASARWANJI, Alan G. Mayton

Nonfatal injuries from slips, trips, and falls (STF) that occur at surface mines can result from inadequate lighting. Mobile equipment operators are among the occupations associated with the nonfatal incidents reported to the U.S. Mine Safety and Health Administration (MSHA). In addition, getting on/off the equipment (ingress/egress) frequently adds to the highest proportion of nonfatal incidents. Accordingly, researchers at the Pittsburgh Mining Research Division (PMRD), National Institute for Occupational Safety and Health (NIOSH) conducted a field study to investigate lighting on haul trucks and wheel loaderswith regard to glare and illuminance levels recommended by the Illuminating Engineering Society (IES). The objective was to determine whether two light-emitting diode (LED) area luminaires—a Mr. Beams® (model MB390 Ultrabright) (area luminaire-1) and a NIOSH-developed Saturn (custom-designed for a mine roof bolter study) (area luminaire-2)—could complement a headlamp luminaire. Measured levels of visual tasks, with the headlamp alone and the area luminaires plus the headlamp, demonstrated that illuminance met or exceeded IES-recommended levels. Nevertheless, the area luminaires illuminated a much broader area, which is key to increasing hazard awareness. Discomfort and disability glare were lower with area luminaire-1 than with area luminaire-2. Differences in glare were more noticeable for newer models of haul trucks and loaders featuring updated ingress/egress system designs. This study demonstrates that commercially available luminaires, such as area luminaire-1, are capable of complementing headlamp lighting, and can thus improve a miner’s ability to detect and avoid STF hazards.

Jun 17, 2020

By C. Rodriguez, T. BoBo

Comminution, being the energy intensive part of a mining operation receives much scrutiny by cost controllers, CEO’s, investors and others as the mining industry goes “back to basics” to reverse the decline in productivity which occurred during the mining super cycle. Blasting is the first and lowest cost per ton stage in the comminution value chain. The basic principle that effective blast design can optimize fragmentation from the Run of Mine (ROM) ore muck pile to improve productivity through digging, loading and crushing to grinding and increase mine site profits has been well documented. Benefits of controlling fragmentation in the blast include reduced wear on equipment, faster loading, increased truck loads while detecting oversize rocks at the muck pile can reduce the frequency of a blocked primary crusher. A second basic principle is a measure of particle size distribution (PSD) at each unit operation in the comminution cycle allows engineers to manage blast design to produce fragmentation in the ROM ore most suitable to optimize downstream unit processes to improve mine site productivity and profits. Split-Online® systems have measured PSD of rocks on conveyors from the primary crusher to the SAG mill for over 20 years. Split-Engineering partnered with various mining companies to develop Split-ShovelCam® to automatically measure fragmentation from shovels and excavators working the ROM muck pile. This paper takes the reader “Back to Basics” by discussing the use of real time fragmentation analysis at the muck pile as an important parameter to optimize energy factors required for each blast. Case studies are given. INTRODUCTION The basics of mining are: • Explore for and find economic resources of valuable minerals • Mine rocks containing valuable minerals using blasting • Crush and grind rocks to liberate valuable minerals (comminution) • Recover valuable minerals for sale Comminution is an energy intensive process which accounts for a major proportion of mine site costs. Effective blasting can improve comminution and deliver significant reductions to mine site unit costs, (CEEC, 2016). Engineers, scientists, builders and even philosophers have long promoted the phrase “measure to manage”; the premise being “you can’t improve what you don’t measure”. Blast Engineers measure fragmentation in ROM ore for feedback to manage energy input in the design of blast patterns to optimize the ROM product size for downstream operations, whether they be for ROM Leach or feed into the primary crusher.

Jan 1, 2019

By Yi Luo, Hua Jiang

A roof bolting drilling operation in an underground coal mine can expose the operator to a high concentration of respirable coal and crystalline silica dusts (smaller than 10 µm). Overexposure of high-level quartz dust for a roof bolter operator can lead to the development of silicosis in as little as three years [1]. This study proposes a drilling control algorithm for the bolt hole drilling process. This algorithm can be integrated into a current drilling control system on the roof bolter machinery and is expected to reduce the generation of respirable dust while enhancing the energy efficiency of the roof bolter machine. In addition, the drilling efficiency and bit condition can be evaluated while drilling based on the real-time feedback parameters. This capability enables the algorithm to ensure the drilling is performed under a relatively high energy efficiency with less respirable dust generation and to avoid drilling with an excessively worn bit that can cause bit clogging or steel buckling failure.

By George Hufford

An investigation is made into the applicability of queueing theory to simulating the operation of a large open pit copper mine in the southwestern United States. Actual data from a working mine was used to construct curves for truck loading time, haulage and return time, and dumping times. Known results of investigations of queueing models (Koenigsberg - 1958, Gordon and Newell - 1967, Cabera and Maher - 1973) were used to simulate the actual operation. These did not give acceptable results so commonly used probability distributions were fitted to the actual data. A large computer program known as Q-GERT was used with the various parameters obtained from fitting the curves. Kolmogorov- Smirnov tests were run that showed that this was not satisfactory either. Finally, Q-GERT was used with the actual data from the mine. An appropriate correction factor is then found to apply to the exponential probability distributions tested previously and satisfactory results are obtained.

Jan 1, 1981

By Rick A. Croote

The objective of the Cerrejon Coal Project is to mine and export a minimum of 15 million metric tons per year of bituminous coal from the Guajira Pennisula in Colombia, South America. Major components of the project will include an open pit mine, 150 km railroad, marine terminal for storage and shipping, and accommodations for the support personnel. This paper primarily reviews the coal handling facilities at the mine and port which will include crushers, conveyors, silos, stacker/reclaimers, and a shiploader. Of special interest is the design concept for unloading bottom-dump railcars, a programmable controller control system with automatic stacking and reclaiming, a linear-type shiploader, and 2.4m wide conveyors running at 5 m/sec.

Jan 1, 1983

By David Hartley

United States Steel Corporation Minntac Mine is located at Mt. Iron, Minnesota, on the Mesabi Iron Range. The taconite pit is two miles long by a mile wide, with a maximum depth of 170 feet. This paper will deal with the radio remote control of locomotives engaged in the railroad haulage of crude ore and waste rock at this property.

Jan 1, 1970

By Stephen F. Munsell

The development of transportation systems for mined materials has historically been characterized by steadily increasing sizes in basic hauling units. This is especially true for open pit mines for which success is dependent upon the economical transportation of vast quantities of material. The depletion of high grade ore reserves has mandated a tremendous increase in the size and complexity of the ore haulage systems necessary for open pit mines, These increased demands were served by rail haulage systems in the early large open pit copper mines while later developed properties opted for the flexibility and lower initial costs of truck haulage. Now, we find the trucks being displaced as large overland belt conveyors tackle the problem of handling these ever larger quantities of low-grade ores with accompanying overburden ratios that can run as high as 10:1 or even 15:1. The basic development of large conveyors with shiftable sections and modular belts has generally taken place overseas, during the last few decades. The coal fields of central Europe proved an ideal testing ground for conveyor innovation because the low density and natural friability of the material created an ideal medium for transporting by belt conveyor. Now these proven ideas are being considered for and implemented into both the soft and hard rock mining industries of the United States.

Jan 1, 1978

By E. Neumann

With fuel costs unstable but escalating, solid fuels are playing an increasingly larger part in industrial concerns. Coal, petroleum coke and wood are examined from a burner system design viewpoint and from operational experience in kilns, hot gas generators, etc. The burner of today must also handle multi-fuel tasks and allow immediate, painless switching from one fuel to the next as well as the simultaneous burning of two or mope fuels. The paper discusses the principle of burning alternate pulverized fuels as well as the practice both in the United States and around the world.

Jan 1, 1983

By Hiroyuki Abé

This paper is a review of research and development on geothermal energy extraction in Japan especially on hydraulic fracturing. First recent geothermal developments in Japan are outlined in Part I. An increase in the production rate of geothermal wells may be highly dependent on the geothermal well stimulation technology based on hydraulic fracturing. The hydraulic fracturing technique must be developed also for geothermal energy to be extracted from hot, dry rock masses. In Part II, the research on hydraulic fracturing and field application are reviewed.

Jan 1, 1982

By FHATUWANI SENGANI

The understanding of yielding pillar behavior has been well documented in terms of pillar strength using numerical simulations and empirical formulas, but the understanding of how fracture propagates in a matured yielding pillar is not well established. A new empirical summation chart of fracture distribution along the matured yielding pillar is presented in this paper. The chart was developed using ground penetrating radar (GPR) supported by borescope observations, focusing on monitoring the distribution of extension fracture.

By Matthew T. Mowry

As the mining industry continues to hire young professionals to supplant the growing number of retirees, a well-developed engineering curriculum, coupled with practical, real-world training, can prepare mining engineering graduates to make meaningful contributions in the industry. Successful companies can be measured not only by their reserve base and annual production but also by their retention of mining engineering graduates with zero to five years of operational experience. My personal experience in the industry during the last five years has been varied and rewarding. The knowledge and experience I have gained have taught me valuable lessons that prepared me for my current role.

Nov 1, 2013

By Roy Norcross

For the past few years Caro's acid has been used for the treatment of cyanide containing slurry effluents, providing a feasible alter­ naive to other slurry treatment processes including !NCO SO2 / Arr and ferrous sulfate. Presently, mines using Caro's acid gen­erate their own Caro's acid onsite making a relatively low quali­ty product. It was at this point where we, at Degussa Corporation, decided to focus our efforts on engineering a Caro's acid genera­tor capable of cost effectively producing a high quality Caro's acid solution, thus reducing operating costs significantly. Caro's acid or peroxymonosulfuric acid is not a new chem­ical nor is it new to Degussa. The product was named after Heinrich Caro (1834-1910), a German chemist who first described its synthesis and its oxidizing properties in 1898. Degussa has been producing the potassium salt of Caro's acid as the triple salt, 2KHSO5 - 2KHSO4 - K2SO4, called Caroat®, for over 30 years. Caroat® is used for household and denture cleansers, as a bleaching agent in dish washing detergents, in printed circuit board etching and for cyanide destruction in the plating industry. From our experience in producing Caroat® Degussa developed its new Caro's acid based DegOX™ technology for the treat­ment of cyanide containing effluents from gold and silver mines.

Jan 1, 1996

By N. Edmonson

Apart from its role as an essential input to a wide array of agricultural chemicals and industrial processes, sulfur is interesting in that its supply involves competition between primary product and by-product. This general production structure is found repeatedly among markets for metals and other industrial minerals, and research results from the sulfur market potentially carry over to other markets with similar structures. The purpose of this paper is to present an analysis of the recent and prospective market for sulfur. The analysis will rely heavily on simulation using a comprehensive model of the North American sulfur market developed by the author. A brief description of the model is offered by way of introduction

Jan 1, 1993

By G. V. R. Landman

In order to obtain a better understanding of the explosion risk at the coal face, anomalies in the ignition sensitivity for different modes of ignition of hybrid mixtures of dust, methane and air were studied. Results indicated that the explosible behaviour of the working environment is highly dependent upon the ignition source and the fuel composition. For example, depending on the ignition source, the same hybrid mixture can be inert or extremely explosible. In conclusion, it is stressed how the explosion risk can be expressed in terms of a safety factor which takes into account the influence of both the fuel and the ignition source.

Jan 1, 1994

By W. Collingwood, K. V. Raj, S. Bandopadhyay

In the mining industry, computational fluid dynamics (CFD) modeling is used extensively to simulate air flow in underground mines. CFD modeling of pollutant transport in openpit mines is relatively new. Modeling the actual pit geometry of an openpit mine and the open domain is complex. The complexity is primarily due to the faceted geometry of an openpit mine with its numerous associated sharp features. Important issues that are not considered carefully at the geometry level are generally propagated to the subsequent processes. Several challenges and pitfalls are encountered in modeling pollutant transport in openpit mines. These challenges and pitfalls are related to the geometry, meshing, boundary conditions and turbulence modeling parameterization. An appropriate mesh selection is critical. A detailed discussion of the meshing of the domain of an openpit mine is presented in this paper. The selection of an appropriate turbulence model, such as kappa-epsilon (κ-ε), large eddy simulation (LES), Reynolds stress model (RSM), etc., to obtain the best possible solution is equally significant. This paper discusses the various challenges in modeling the pollutant transport process in an openpit and some of the approaches adopted to address these challenges.

Jan 1, 2013

By R. V. Ramani

An improved mine environment is the single most critical factor affecting the health and safety of workers engaged in underground coal winning. A very important subclassification of this wide field is mine ventilation, which essentially deals with 'mine atmospheric environmental control.' To ensure proper mine atmospheric environmental control, adequate quantities of air must flow through working sections in the mine. In recent years much attention has been paid to the fan and its prime movers, but the efficient use of the fan output in the workings has not received an equal amount of investigation. In mechanically ventilated mines friction losses in main airways often account for 70 to 90 percent of the total pressure loss sustained in the system. Also the leakage losses are a serious detriment to the efficiency of mine ventilation systems. It is not uncommon to loose 60 to 70 percent of the air between the fan and the last open cross-cuts due to leakage directly into the return Proper assessment of these losses in simulating and projecting complex ventilation systems is vital. Network analysis of ventilation systems is not new. Scott and Hinsly (1951) presented the detailed mathematical framework. Since then work has been done in adopting this technique to analog, and within the past few years, to digital computers. Development of computer programs to solve ventilation network problems has been reported in United Kingdom, Japan, U.S.S.R., South Africa, Germany, and the United States. The purpose of these programs is to serve as an experimental mine wherein analysis of proposed alternatives or ventilation planning can be tested. The great power of the computer as a planning tool lies in the ability to input empirical or Projected data into programs with predicting ability. But, however good a computer program is, unless fairly accurate input information is available accurately assessing the engineering factors of the ventilation system, the output will be suspect. Thus, to simulate and project mine ventilation systems, good estimates of leakage and friction factors are important. Yet, relatively little work has been done in the past three decades to determine these more realistically.

Jan 1, 1973

By H. Kimura

A new technology for ironmaking based on direct gaseous reduction of iron ore concentrate is under development. The process is based on the flash reduction of the concentrate particles in a gaseous reducing agent, such as hydrogen, natural gas, a reducing gas generated by partial combustion of coal, or a combination thereof. This technology is expected to drastically lower CO2 emission and reduce energy consumption by about 38% of the blast furnace requirements. The energy savings are possible largely due to the elimination of pelletization and cokemaking. Process design and simulation using hydrogen as the reductant for iron ore concentrate have been performed. A process flow sheet composed of a flash reactor, heat recovery system, water removal system for purifying recycled hydrogen, and all connecting streams was evaluated using the METSIM software. Ironmaking using two reactors was also designed and simulated, which could reduce the total required amount of hydrogen although it would increase the complexity of the flow sheet and operation.

Jan 1, 2010