Search Documents

By B. K. McMahon

Block caving is an efficient mass-production method for the underground mining of large orebodies. However, the block-caving method requires a substantial investment in developmental works, based on the assumption that the rock will cave. Efficient block caving is prevented if the rock forms stable arches or breaks into fragments that are too large to pass easily through the finger raises. Under these conditions, the cost of the additional labor, drilling, and blasting required to assist caving may be sufficient to make marginal orebodies uneconomic or alternative mining methods more attractive. Reliable methods for the prediction of the block-caving behavior of an orebody are clearly needed at the initial planning stage. These methods should be capable of considering both geological and engineering aspects of a block cave, as experience has shown that the manner in which a block cave is initiated and developed may be almost as important as the geological conditions such as the nature of the rock material, degree of alteration, characteristics of the joints and faults, etc. The initial state of stress in the rock mass should also be considered.

Jan 1, 1969

By Paul K. Edwards

The forces of nature have concentrated sand at various geographical locations that are being mined and processed for a large variety of industrial uses. While most operations serve a number of industries, this paper deals only with the foundry requirements. The forces that have decomposed a source rock, transported this material and redeposited it, have created two general types of sand. These types are classified as the (1) Lake and Bank Sands and (2) Silica Sands. The Lake and Bank sands will contain 92 to 94% Sio2 while silica sands are in excess of 98.5% Si02 and most of the producers wash these sands to up grade their products to 99.5% or better. Included in the Lake and Bank sand would be the river sands that are used primarily for construction purposes. The Foundry Industry is broken down into three types of castings : 1. Grey Iron Foundries The grey iron castings largest market is the automotive industry in Ohio, Northern Kentucky, Indiana, Illinois and Michigan. These castings are poured at temperatures ranging from 2400° to 2700°F. The Silica Sands or the Lake and Bank Sands will satisfy the requirements of the grey iron castings. There are 2 ½ to three million tons per year shipped from the state of Michigan far grey iron castings by the Lake and Bank Sand Producers.

Jan 1, 1974

By K. V. Raj

"The development and advancement of computational fluid dynamics (CFD) has made it possible to better understand pollutant flow and distribution in deep open pit mines. Open pits located at higher latitudes, especially in the Arctic and sub-Arctic, face a unique problem due to atmospheric temperature inversion, which is prevalent during much of the winter. A three-dimensional CFD model of an actual open pit mine in the Arctic was developed to analyze the problem of pollutant growth during inversion, and mitigation of the pollutants through improved ventilation schemes. Due to the availability of mine-specific data, such as contaminant concentrations and coordinates of sampling locations, the actual 2013 pit geometry was used for model validation Concentrations predicted by the selected realizable ?-e turbulent model are compared to measured pollutant concentrations at the open pit. Pollutant concentrations at selected locations showed differences, but remained within the same order of magnitude in most cases. INTRODUCTION Computational fluid dynamics (CFD) has emerged as a useful tool for ventilation modeling in underground mines (Edwards and Hwang 1999, Purushotham and Bandopadhyay 2009, Wala et al. 1998, Xu et al. 2011). Application of CFD in open pit mines has been limited, however, since most open pit mines located at lower latitudes do not encounter considerable ventilation problems. Open pits located at higher latitudes, especially the Arctic and sub-Arctic, face a unique problem due to atmospheric temperature inversion, which is prevalent during winter. A number of Russian researchers have tried to understand the air inversion and resulting pollutant transport problem by modeling air flow phenomena in open pit mines (Baklanov and Burman 1996, Baklanov 1984, Baklanov 1995, Belousov 1985, 1989, 1995). Much of their work, however, was based on numerical models and methods of finite difference. Baklanov (2000) applied a modified ?-e and a ?-l CFD model to air flow phenomena on various terrains. More recently, Choudhury (2011) used the COMSOL CFD package for modeling pollutant transport for an idealized open pit mine. Collingwood et al. (2012a, 2012b) used a two-dimensional model for fluid flow and contaminant transport at an Arctic open pit mine. The authors have also previously presented work on CFD modeling of an actual open pit mine at high latitude (Bandopadhyay et al. 2014, Raj et al. 2015a). However, the CFD work done by the above-cited researchers lacked model validation with field-measured data. Validation of a developed model is important in assessing the quality and accuracy of the predicted results. In general, experiments are done numerous times in controlled environments to assess the validity of collected data. There are two types of assessments used in CFD simulations: (1) verification and (2) validation. Model verification is checking the accuracy of the computer codes during the implementation phase of a real-world problem, within the specific limits of accuracy (Oberkampf and Trucano 2002). Since, the pollution transport model presented in this paper used the commercial ANSYS-FLUENT CFD package, verification is not needed as the program has been tested widely, and verified numerous times."

Jan 1, 2016

By Joseph K. Cavey

To accommodate the new Pier A expansion at BWI airport, a 1.8 m (6.0 ft)diameter stormwater pipe was constructed below active Runway 15R-33L. The jacked tunnel alignment runs east/west below the runway, and the depth the crown was 6.1 m(20 ft). Soil conditions consisted of very loose to medium sand and gravel, with some medium stiff clay and silt. Super Jet Grouting was selected as the ground treatment system, creating large diameter columns. All work was performed from the surface of the runway between the hours of 12 am and 6 am. Monitoring points along the tunnel in the grout zone indicated zero settlement during tunneling. Tunneling operations in front of and beyond the treatment zone experienced significant settlement. Super Jet Grouting in the treatment zone provided a low permeability continuous stable soilcrete that was readily mined while the runway remained in service.

Jan 1, 2003

By William T. Ingram

Early in the 60's the author served as Chairman of the Engineering Foundation's Coordinating Committee on Air Pollution Research. One of our objectives was the development of a study on the measurement of stack emissions. Three publications of the Foundation resulted from these efforts to focus attention on the stack sampling problem.1,2,3 Two of these were annotated bibliographies covering 197 references. The third reported the results of a workshop meeting at which some 21 individuals from research institutes, industry and government discussed the possible and probable areas of research that would add to or increase the ease, precision and utility of sampling gaseous and particulate matter emitted from stacks. The American Society of Mechanical Engineers has had in its Power Test Codes a Standard Code for Determining the Dust Concentration in a Gas stream4 since 1941, The American Industrial Hygiene Association has published, in its Air Pollution Manual,5 a Section on Stack Sampling. Industry and regulatory agency requirements for stack sampling have utilized some modification of the alternatives in methodology. There has been ho single guide to stack sampling that met the needs of those who have the need to know.

Jan 1, 1970

By A. K. Sinha

Ever since electricity was introduced, electrical injuries and electrocutions have continued to occur regularly in coal mines. An analysis of the two hundred cases of electrocutions which occurred during 1956 to 1970 indicated that over 50 percent of the incidents were caused by the ineffectiveness or lack of electrical grounding. Research shows that various types of arbitrarily designed ground beds are in use and that the ground resistance and current are often very high and subject to wide seasonal variations. The results of a recent research are discussed in this paper.

Jan 1, 1980

By K. E. Doud

An unusually pure grade of rutile and several grades of aplite rock are produced in a unique mining and mineral dressing operation in Hanover County, Virginia. The ore body is an aplite rock of gnessic structure, having a sari ace exposure extending over several hundred acres, heavily leathered and containing rutile, ilmenite, and other titanium and iron minerals. The physical nature and mineral composition of the ore body has permitted the use of a relatively economical and unusual processing circuit. The flowsheet was designed to take full advantage of the remarkable liberation of the minerals at relatively coarse rinds. It permits flexibility in changing the product mix, and maintains high levels of purity in both rutile and aplite rack. The mineral processing is discussed in some detail below.

Jan 1, 1962

By A. K. Bhowmick

Size reduction is very energy intensive and is the single most power-intensive operation in mineral processing plants. Research has shown that only a small part of the energy is utilized efficiently. One of the major thrusts of all equipment manufacturers has been to improve this efficiency. Choosing the right equipment to maximize energy utilization in any comminution application has always been the utmost criteria. Due to the high energy cost and depletion of good grade minerals, it is becoming essential to optimize all the subsystems within a given comminution system for the overall economic success of such ventures. Bradley Pulverizer Company of Allentown, Pennsylvania recognized this and started offering its Feeder Controller in 1988 for automatic feed control. After its first successful operation, Bradley made this as a part of all of their grinding system standard offering. It was also recognized that the Feeder Controller was just a beginning and more automation and controls would be required for an overall, efficient grinding system.

Jan 1, 1993

By D. K. Grubbs

Anorthosite is an abundant, domestic source of alumina with reserves in individual deposits ranging from a few billion to hundreds of billions of tons. While anorthosite contains less alumina than does kaolinite, its CaO and Na20 contents are significantly higher (Figure 1). Alumina can be produced from anorthosite by alkaline, soda-lime sinter or acid processes. CaO and Na20 are advantageous because they are reactants consumed in alkaline processes. Acid processes require high calcium plagioclase feldspars (bytownite-anorthite) to obtain high alumina extraction because the lower calcium plagioclase feldspars (andesine-labradorite) are not as readily dissolved during digestion. The layered Raggedy Mountain Gabbro group in the Wichita complex in southwest Oklahoma is a high calcium anorthosite that could be processed by acid, sinter, or alkaline methods. Chemical grade limestone in the Arbuckle Group is located within 45 km of the anorthosite (Figure 2).

Jan 1, 1980

By Raj K. Rajamani

In ball milling the rates of breakage vary primarily with the size distribution of powder in the mill. In wet grinding viscosity of the slurry varies continually as size distribution changes and hence the breakage rates change. In this study a simpler estimation scheme is used to determine breakage rates in batch grinding. Using an approximate solution to the batch grinding equation, acceleration and deceleration of breakage rates of all individual size classes is determined when the grinding environment is varied. Experimental results with limestone and copper ore show time-dependent breakage rates under both dry and wet grinding conditions. In general the breakage rates increase for coarse sizes and decrease for fine sizes with increase in the fines present in the mill. Such variations have strong implications in closed-circuit grinding.

Jan 1, 1991

By S. K. Singh

"Feather edging"-a major source of injury and fatal accidents in Australia, South Africa and USA, refers to a phenomenon where the roof, at the goaf edge, falls as a thin wafer of rock often suddenly, over-riding conventional timber breakerlines. It may run down and affect adversely a working bord at distances of 15 metres or more from the goaf edge. Feather edging typically occurs in relatively massive, strong roof strata such as sandstone or conglomerate. This paper presents the results of a mine trial where a concentrated row of fully grouted bolts were able to resist the feather edging in the first comprehensive, monitored trial in an Australian pillar ('total') extraction coal mine.

Jan 1, 1999

By Emmet K. Oslen

Kaiser Steel Corporation, the pioneer steelmaker on the Pacific Coast, was founded by the late Henry J. Kaiser. In 1944 the Company purchased from the Southern Pacific Railroad an iron ore property 200 miles east of Los Angeles known as Eagle Mountain. Today the domestic operation of Kaiser Steel Corporation consists of the iron mine at Eagle Mountain; two coal mines, one each in Utah and New Mexico; an integrated steelmaking complex at Fontana, California; and several steel fabrication and erection facilities along the west coast. Kaiser Steel also has interest in Hamersley Iron, Ltd., Australia, and Kaiser Resources, Ltd., British Columbia. Eagle Mountain Mine is located about 80 miles east of Palm Springs and adjacent to the southeast corner of Joshua Tree National Monument. The area is one of the most arid in the world averaging only two inches of rain annually. Geologically, the mine is at the western edge of the Basin and Range Province which covers about one-half million square miles of the western United States. The Province is typified by north to northwesterly trending fault block mountain ranges separated by sediment filled valleys, Production has totaled over 82 million tons of finished products since the first shipment in June, 1947. Over 500 million tons of material have been mined from the deposit to date. Eagle Mountain Mine is noted for the pioneering use of the largest and most up to date equipment to mine and process its ore. In 1961 Eagle Mountain received the first fleet of 100-ton haulage trucks in the mining industry. There were thirteen semi-trailer units in the fleet. The first 12 to 17-yard size shovel in the mining industry was placed in operation at Eagle Mountain during 1962. Rotary drilling was introduced at Eagle Mountain in 1954 to replace churn drilling. Eagle Mountain was the first major mine to use metallized slurry when three aluminum slurries were introduced for primary blasting in 1962.

Jan 1, 1972

By K. L. Browne

After a decade of high copper prices, major mining companies are renewing their interest in purchasing operating properties and/or developing ore bodies. An existing operation carries with it a history that can present unique opportunities, while a greenfield operation allows for the establishment of a defined culture. Capital investments are distinctly different. A comparison of BHP Copper's Robinson operation, a greenfield property, and BHP Copper's Tintaya operation, a government owned Peruvian property, will provide insights into mining, concentrating and cultural differences between North and South America operations. The Broken Hill Proprietary Co. Ltd. (BHP) is Australia's second-largest company. Fiscal year 1996 sales were US$16 billion, profits were more than US$1 billion and total market capitalization was about US25 billion. In 1885, BHP began mining silver, lead and zinc at Broken Hill, New South Wales, Australia. Throughout its 112-year history, BHP achieved an impressive record of performance and expansion. Today, BHP is one of the world's leading companies (66th on the Standard and Poors 500), having diversified into steel, petroleum and mining with more than 65,000 employees in 70 countries.

Jan 1, 1997

By Surendra K. Mishra

Metallic and oily components are the major contaminants of industrial wastes. Underground burial and incineration have been the commonly practiced methods of waste management. To provide a relatively more permanent solution, different processes have been developed. In addition to reviewing these processes, potential of using flotation as a process to treat hazardous metal and oil contaminated wastes is discussed in this paper.

Jan 1, 1989

By K. L. Johnson

Networks of monitoring wells were established prior to mining at four longwall mine sites in the Appalachians to monitor the effect of mining on water levels, water quality and well yield. Two of the sites were located in stream valleys and the other two sites were located on hilltops. The depth to the mined seam ranged from 500-850 feet with the deeper cover being associated with the hilltop sites. Maximum declines in groundwater levels during and after mining were an order of magnitude less in the stream valley aquifers than in the hilltop aquifers. However, water levels in hilltop wells located outside the area immediately above the panel were unaffected. Water quality changes in wells as a result of longwall mining were negligible at all four sites. Increases in aquifer transmissivity and well yield were much more pronounced in the stream valley aquifers than in the hilltop aquifers. The significantly larger recharge area for the stream valley aquifers than that for the hilltop aquifers may partially account for the differing responses of these two classes of aquifers to longwall mining. These observations appear to be consistent with the stress-relief fracture model for Appalachian Plateau groundwater hydrology proposed by Wyrick and Borchers in 1981.

Jan 1, 1986

By S. K. Sharma

The Bureau of Mines' rapid method of dewatering fine-particulate slurries uses extremely high molecular weight polymers. These polymers form large, strong flocs which can be dewatered by sieving or sedimentation. However, sometimes these flocs deteriorate rapidly if water is not removed immediately. During field tests, clay slurries have been encountered that could have been dewatered economically if it were not for the rapid floc deterioration. A kinetics study was conducted to determine the rate of kaolin-PED floc degradation in which polymer addition, to bring the flocs back to their original condition, was used to determine the extent of floc decay. Results showed that the amount of polymer added, to replace polymer lost by spreading, was less for the lower PEO concentrations. For this clay-polymer system, floc breakage as judged by polymer additions followed first order kinetics. It was also found that the addition of fluoride ion stabilized the kaolin flocs.

Jan 1, 1992

By K. J. Reid

A historical background of the development of automated material balance packages is presented including a summary of currently available packages and a description of the present work at the Mineral Resources Research Center of the University of Minnesota. A brief mathematical statement of the problem is given and solution techniques discussed. The problems and difficulties normally associated with material balances, both hand calculated and computer calculated are described. Several aspects of the available material balance packages as related to the "user/computer" interface are evaluated in detail. Elements of the material balance packages that affect the solutions are examined and the relative performance of the main packages on specialized problems presented. Finally, areas associated with automated material balances that require further work before computer packages can be widely used in industry are outlined.

Jan 1, 1982

By B. K. Parekh

Silicon carbide (SiC) can be produced by heating rice hulls to elevated temperature, The product is a mixture of beta crystalline silicon carbide whiskers, particles and unreacted carbon. The silicon carbide whiskers are 0.5 micron in diameter and 50 to 100 micron in length and have been found useful for reinforcing metal and other composite materials. The carbon can be removed by combustion, but this makes separation of the silicon carbide whiskers from particles difficult and a high grade whisker product cannot be made. However, a clean high grade Sic whiskers product can be obtained from the pre-burned converted rice hulls using physical separation processes that are based on differential wetting. Recovery of Sic whiskers from the pre-burned material was found to exceed 90 percent. A modification of the froth flotation process developed during this study is now being used commercially to separate silicon carbide whiskers and particles and to recover a high grade whisker product.

Jan 1, 1985

By K. T. Mau

Hawaii is located approximately 2,500 miles from the mainland, but has basic needs for its thriving developing community. Cement is one of these needs Cement production in Hawaii is not without handicaps. The necessary raw materials are practically non-existent except for limestone. Even at that, the available limestone is marine in origin, coralline in nature and amorphous in characteristics - unlike calcite which is normally the calcium carbonate source for cement manufacture. There is no clay or shale for the argillaceous portion of cement raw mix. Hawaii being volcanic in origin is too young geologically for clays and shales to evolve and whatever there is, most likely is washed into the ocean.

Jan 1, 1982

By W. K. Pincock

Accident prevention can be portrayed as a science that deals with facts and natural phenomena and must be dealt with in the same manner as any other operating problem. Safety at the Copper Queen Branch dates back to 1913 when a Safety Organization was started and rules formulated for underground mining. Since then the mining industry has made substantial progress in the elimination of accidents and when the Lavender Pit was started in 1951, it adopted the general plan in use at all Phelps Dodge properties. Following is a brief description of the Pit Operations:

Jan 1, 1959