Search Documents

By K. F. Unrug

Martin County Coal Corp. is located in Martin County, KY, in the Appalachian coal fields, near the West Virginia border. The company's total leasehold covers more then 133.5 km' (33,000 acres). Total annual production at Martin County Coal Corp. is currently 2.2 Mt (2.5 million st). In certain years, though, it exceeded 2.7 Mt (3 million st). About 45% of the annual production comes from two surface mines. The balance is produced from five underground mines. Martin County Coal's work schedule consists of two nine-hour shifts a day, 240 days a year. Topography The topography of the area is characterized by rugged hills and ridges and sharp V-shaped valleys demonstrating a cliff and slope topography. This topography consists of alternating benches of outcrop sandstone and slopes. The deep valleys have been carved out by many small streams in the area. These streams are contained within the steep slopes of narrow, twisted mountain ridges. The ridges are underlain by massive sandstones that, being resistant to erosion, create sharp, rocky morphology. The height of the hills above the valley floors ranges from 122 to 244 m (400 to 800 ft).

Jan 1, 1991

By William H. Wiese

Anecdotal reports of high rates of congenital malformations and spontaneous abortions at the Shiprock Indian Health Service Hospital in San Juan County, New Mexico prompted an interview survey, obtaining data from families of 26 former uranium miners and 30 controls. Results supported the possibility of increased fetal wastage and congenital malformations. However, definitive conclusions were obviated by methodologic limitations in terms of selection of cases and controls and interviewing technique, as well as very low numbers and lack of statistical significance. The Council of Environmental Quality (1980) published a report which singled out San Juan County, nationally, as having an extra-ordinary high rate of congenital anomalies reported from birth certificates in the years 1973-75. San Juan County is in the northwest corner of New Mexico and includes the northeastern edge of the Navajo Indian Reservation. It has been the site of uranium mining and milling and also of coal mining (Clement Associates, 1980). While much attention has been focused on lung cancer and chronic lung disease as health hazards to uranium miners, virtually no attention has been focused upon possible reproductive effects that may result from exposure to radiation. Could these reports indicate such an additional arena of health effect either on miners or on others living in the vicinity of the mines and mills? The biologic and epidemiologic literature does not lend much support for adverse genetic outcome. The UNSCEAR report (UNSCEAR, 1977) summarizes much of the existing data. For example, on the basis of many animal studies and what has been observed in atom bomb survivers in Japan, it has been estimated that mutation rates resulting from low LET radiation to paternal germ cells would be 60 X 10-6 recessive and 20 X 10-6 dominant mutations per gamete per rad. There would be a five-fold increase in the number of recognizable abortions. The doubling dose for genetic disorders in mice is estimated at 100 rads. The assumption has been that low levels of exposure, such as might be received occupationally from uranium mines and mills or environmentally will produce reproductive effects that would defy distinction from background rates. However, the possibility can not be dismissed. In man, spermatogonia are thought to be three-fold more sensitive than in the mouse. Also, the high LET radiation from alpha particles is as much as 20-fold more effective in inducing changes in meiotic and post meiotic stages of cells, compared with low LET radiation. There is some degree of localization of alpha emitters in testicular tissue after inhalation of radon and radon daughters (Blanchard, R.L. and Moore, J.B., 1971; Pohl, E., 1964). The slopes of doseeffect curves are affected by type radiation and rate of administration. Data on such curves are poorly defined and debated as to whether there may be increased or decreased effect per unit dose at low levels of high LET radiation. Increased rates of aberrations of chromosomes in peripheral lymphocytes cultured from uranium miners have been reported (Brandom, W.F., et al., 1978). At cumulative exposures of 100 working level months (WLM) or less, a range of exposure lower than the limit of current occupational standards, the aberrations were increased more than two-fold. Our interest has led us to pursue the question of reproductive effects along three separate paths of inquiry: studies of the secondary sex ratio, cytogenetic study of human sperm, and studies of rates of congenital anomalies. I will present the thrust of our findings, most of which remain preliminary, comment on their interpretation and limitations, and indicate directions needed for future research. The secondary sex ratio is the ratio of males to females at birth. In the U.S., the ratio averages around 1.05. Ratios in blacks are somewhat lower (1.025) than in whites (1.053). For American Indians, the data are less definite. Values from Oklahoma and California are similar to whites (1.05). Southwestern tribes have, as we shall see, varying levels. The theoretical effects on sex ratio resulting from irradiation of the zygote are based on the principles of sex-linked genetics, including differential effects of lethal dominant and recessive mutations on the sex chromosomes, complicated by possible non-disjunctional events. Observations have done little to clarify, confirm or refute the theories. The sex ratio of progeny of survivers of the atomic bomb showed little change (Schull, W.J., Otake, M., and Neel, J.V., 1981). Observations in children of uranium miners having been inconsistent. Most frequently cited is a study of miners in Czechoslovakia (Müller, C., Razicka, L., and Bakstein, J., 1967). Compared with children born to miners prior to the start of mining, the sex ratios of children born after the start of mining were decreased -statistically significant after correcting for birth order. The ratios in first-born children were, before the start of mining, 1.118, and, after the start of mining, .713. In the interview survey at Shiprock, the sex ratio in families of non-miners was 1.03, and in families of miners it was 0.73 (p < .05). Dr. Alan Goodman at the University of New Mexico has studied trends in the sex ratio in the general population in New Mexico and Arizona with particular reference to counties in the Four Corners area and the Navajo Indian Reservation, areas where uranium mining has been active_ His findings (unpublished) are as follows: (1) Beginning in the early 1950&apos;s, there has been a modest, but persistant and statistically significant decline in the secondary sex ratio for the state of New Mexico compared with the U.S., a decline that roughly parallels the emergence of uranium mining in the Grants mineral belt in northwestern New Mexico. (2) Data available for the 11 years since 1969 show that among the five counties with ratios significantly lower than the state

Jan 1, 1981

By Eric K. Albert

Computer oriented simulation techniques can be effective in the design and analysis of complex mining systems. In fact, a number of computer software products are available for mine systems simulation. However, previous models have tended toward being either data-intensive and deterministic, or data-limited and highly stochastic. The need for a fully integrated package with a simplified user interface has never been more apparent. In this paper, the design of a surface mining simulation model documented in Albert (1986) is described. The basic features of the surface mining system and their counterparts in the simulation model are discussed. The methods and algorithms used to implement these subsystems are presented. Considerations of information management and software design are illustrated, especially as they apply to the application of the package by a mining engineer. An example is provided to demonstrate the concepts embodied in the model and to show how a surface mine is simulated from mine parameters.

Jan 1, 1989

By Paul Culvenor, Brad Gyngell

Large language models (LLMs) have generated a lot of hype since ChatGPT was released in early 2023. In essence, they allow people to interact with computer systems through natural language and have the ability to generate highly complex text, images and videos (Patil and Gudivada, 2024). It is clear that this technology has significant potential, however most mining companies have not yet found practical applications for it within their operations. In this paper, we present a range of such applications along with the tactical considerations associated with developing and implementing them. We have identified use cases across a variety of operational and functional areas within the mining industry and evaluated them based on their potential business value and ease of implementation. Firstly, we provide an overview of how LLMs work and a review of how LLMs are being applied in other industries to provide best practice inspiration for mining. Next, we present a list of possible applications in mining and a critical assessment of each use case. This section also includes a technical deep dive into the different methodologies for developing the technologies as well as an analysis of barriers to adoption within mining organizations. Finally, we share a discussion of the potential path forward for LLMs in mining and the impact they could have on the industry. We analyze the potential differences between early adopters and laggards in the artificial intelligence (AI) space. This research draws on interviews and surveys with artificial intelligence experts as well as mining subject matter experts to connect cutting edge thought leadership with the specific problems faced by our industry.

Feb 1, 2025

By K. -A. Björkstedt

INTRODUCTION Strassa lies in the central part of Bergslagen, a tradi¬tional mining district, on the eastern side of the Stora Valley at an elevation of about 200 m above sea level. A railway siding runs between the mine and the Stora railway station from which there are railway connections to the shipping port and iron and steel works in Oxelosund, about 224 km away. The distance to the provin¬cial capital Orebro is about 60 km. The climate is typi¬cal for this part of central Sweden and is illustrated by the diagram of monthly precipitation and temperatures for the years 1968-1975 (Fig. 1). HISTORY There is no certain information as to when the Strassa mine was first worked, but it is known from sur¬viving accounts of mine inspectors that there were smelt¬ing works in operation in nearby villages in the 12th century. An example is the Gusselhytta ore smelting works, 10 km south of Strassa, which dates from this period. Around the year 1540 there were two smelting works in Strassa, the Upper Karberg and Lower Karberg works. Ore for these smelters was probably taken from Strassa and from the adjacent Blanka mine. In the year 1624 Strassa is mentioned by the painter Jons Nils Krook in an account of the iron mines in the Linde mining district (Linde Bergslags Jarngruvor). Several mines were listed in the area, the deepest being about 30 m. An impressive power installation is mentioned in 1639, including a piston system of lashed poles for transmit¬ting power from the Stora River to the Strassa fields. Its length was 2670 m. Common ground comprising about 20.2 km2 (5000 acres) of forest was allocated in 1689 for the furtherance of mining operations. Until the beginning of this century only the rich cen¬tral parts of the ore body were mined and these yielded, after handpicking, lump ore suitable for smelter feed. An example of the ore grades from these early times is an analysis of ore from the "Big Mine" (Storgruvan) from the year 1873: 48.5% Fe, 0.008% P, and 0.06% S. This same year a total of about 18 000 t was ex¬tracted from the Strassa mine. OWNERSHIP The mine was owned and run until 1874 by a min¬ing association made up of 119 so-called "bergsman," who were homesteaders often engaged in agriculture and timber-cutting as well. In that year the Strossa Grufvebolag (Mining Co.) was founded. In 1906 it was con¬verted into a joint stock company, the Strossa Gruveaktiebolag. This was acquired in 1907 by Metallurgiska AB for the implementation of Gustav Grondal&apos;s beneficiating and briquetting methods, for which the Strassa ore was well suited. The same year saw the completion of a new ore dressing plant with an annual production of 46 000 t of ore concentrate. In 1911 the mine passed to new hands, and in 1913 it was purchased by an Austrian company. Extensive new installations were made and in 1915 a new dressing and briquetting plant was completed with twice the capacity of the old one. In 1917 the Strassa mine was acquired by Granges. Be¬cause of unfavorable business trends and technical diffi¬culties, mining operations were brought to a close in 1923. Pumping kept the mine free of water until 1933 but it was completely filled ten years later. Up to 1950 the surface buildings and installations remained intact but the large dressing and briquetting plant burned to the ground in that year. Today only the machine shop re¬mains from this earlier period of operation, now housing parts of the Mineral Processing Laboratory. The decision to take up mining operations again was made in 1955 and construction work began the follow¬ing year. Of the old installation, only the "southern shaft" could be used for some development drifting after it had been completed with a new headframe. Other¬wise, all the buildings and installations required for the operations had to be rebuilt. New installations ready by 1960 were office and personnel facilities, a new shaft and headframe, a sorting and concentrating plant, a macadam plant, settling basins, pump stations, and a railway and yard with transport equipment. The instal¬lation was completed with two plants

Jan 1, 1982

By G. T. Newell, J. G. Stone, V. M. Mejia

Introduction Advances in drilling have reached a point where large diameter cores can be recovered from "tight," or weakly indurated placer gravels. In such ground, core drilling can provide more reliable data regarding tenor than can be obtained using churn drilling or similar classical techniques. It can also provide metallurgical and geological information that is not available from samples obtained through alternate methods. In 1985, Coastal Mining Co, a subsidiary of M. A. Hanna, and Western Gold Reserves began to review a Tertiary placer deposit owned by San Juan Gold at North Columbia, CA, about 14 km (9 miles) northeast of Grass Valley. The deposit is one of the largest remaining unmined portions of the formerly extensive early Tertiary ancestral Yuba river system. It has been known since the 1850s, has been the subject of much technical literature, and has been the object of at least four previous drilling programs. The eastern one-third of the 6 km (3.7 mile) stretch of the channel between North Columbia and Badger Hill was partially stripped by large scale hydraulic mining in the late 1870s and early 1880s. Mining ceased in 1884 when the Sawyer Decision prohibited further discharge of hydraulic tailings into the Sacramento and San Joaquin Rivers. By that time, about 30 to 45 m (100 to 150 ft) of relatively low grade upper gravels had been removed over some 81 hm2 (200 acres). About 90 to 105 m (300 to 350 ft) of higher grade middle and lower gravels were left at least partially stripped. In 1914, a few churn holes were drilled along a widely-spaced line. In 1938-1939, Selection Trust conducted an extensive drilling campaign to evaluate the deposit. Particular attention was directed toward the partially stripped eastern portion. In 1968, the US Geological Survey drilled three churn holes in the eastern part of the deposit. The US Bureau of Mines conducted experimental mining and drilling in the Badger Hill area. In the late 1970s, Placer Service Corp. acquired a lease on the deposit. Between 1979 and 1984, Placer Service drilled 28 large diameter BADE (a German-manufactured machine) drill holes on the eastern portion of the deposit. The surviving records from the widely-spaced 1914 drilling program are fragmentary and the reported grade not well substantiated. The 1968 holes were drilled for scientific purposes. Again, drilling details are not available. However, detailed records for both the churn drilling program and the BADE program were available and formed the basis for the initial evaluation of the property. Geology The geology of the auriferous Tertiary gravels of California have been described by Whitney (1880), Lingren (1911), and, more recently, Yeend (1974). In general, the Tertiary gravels in the North Columbia area occupy a broad channel cut into pre-Tertiary igneous and metamorphic rocks. The upper, or white gravel is overlain conformably by volcanic tuffs and volcaniclastic rocks. A middle gravel is characterized by the presence of silicified and carbonized wood. A lower blue gravel unit has relatively coarser cobbles and contains a higher proportion of igneous and metamorphic cobbles than the other units. The upper gravel consists of interbedded pebbly sand and silty, or clayey sands with prominent cross bedding. Most of the pebbles are well rounded and consist mostly of white vein quartz and quartzite. The upper unit is moderately well compacted. Exposures in the walls of the old hydraulic mine pits stand at 45° and 50° angles. The gold content of the unit is well below an economic cutoff. The middle gravel - included with the upper unit by Yeend (1974) - is coarser grained, with carbonized wood, and 75 to 100 mm (3 to 4 in.) cobbles of metased-imentary and metavolcanic rocks in a sandy matrix containing abundant lithic fragments. The upper contact appears to be conformable, but the lower portion of the unit appears in places to consist of reworked lower gravels. The unit contains less clay than the upper unit and is somewhat more friable than the underlying lower gravels. The gold content, while somewhat higher than the upper level, is too low to be of ore grade. The lower gravel averages between 30 to 45 m (100 to 150 ft)

Jan 9, 1988

By Gregory P. White

A number of private companies and universities have developed computer programs which can be used to simulate surface coal mining by dragline. In this paper, we briefly discuss the concept of computer simulation, compare these computer programs with each other, describe the major changes required to convert these programs to an IBM computer system, and analyze their sensitivity to inaccurate input data. We also present a summary of the required data input for each program, core storage requirements, and output results. Sources for obtaining these programs and their documentation are listed at the end of the paper.

Jan 1, 1983

By Donald E. Ralston, A. T. Yu, Richard P. Killmeyer, Peter Phillips, R. W. Vander Laan, John N. Murphy, John R. Messineo, John Peters

Overview Coal production in the first half of 1982 remained near the high levels begun in mid-1981. Production then fell sharply during the latter part of the year due to recession-weakened demand. Even so, 1982 coal production was estimated at 756 Mt (833.4 million st), a record high that exceeded 1980&apos;s previous production record of 752.7 Mt (829.7 million st). Though 1982 coal production was substantially below industry expectations, the attained production represented a modest achievement in view of the recession&apos;s severity. In 1982, the gross national product declined 1.8%, its worst performance in 36 years. The recession, along with mild weather, improved energy efficiency, and conservation efforts caused the nation&apos;s energy use to drop 4.1%. With the iron and steel, construction, and auto industries experiencing production declines, industrial energy use fell 10.8%. The extent to which the nation&apos;s economic slump affected coal markets in 1982 varied: • total domestic coal use declined 3.4%; • exports remained strong for most of the year; • electric utility coal use declined for the first time in 25 years; • coal use at coke plants declined by one-third; and • coal use in other industrial sectors stayed surprisingly near the 1981 level. Coal Use Domestic coal use totaled 641.8 Mt (707.5 million st) in 1982,22 .9 Mt (25.2 million st) below the 1981 level. Nearly all the decline occurred at coke plants where use dropped to 37.1 Mt (40.9 million st) in 1982 from 55.3 Mt (61 million st) in 1981. The decline in all other industrial and electric utility coal markets was only 5.3 Mt (5.8 million st). Residential and commercial coal use increased 635 kt (700,000 st) to 7.3 Mt (8.1 million st) from 6.7 Mt (7.4 million st). Power generation decreased 2.3% in 1982, the first year since 1945 that output failed to increase. The decline was due to a drop in industrial demand. Electricity sales to residential, commercial, and other nonindustrial users increased slightly. But coal&apos;s competitive position stayed strong. Power generation from oil and natural gas fell 28.9% and 11.7%, respectively. Power generation from coal declined only 0.9%. Among the primary energy sources, coal fueled 53.2% of US electric power generated in 1982, compared with 52.4% in 1981. In 1982, US steel production declined to 66.1 Mt (72.9 million st), the lowest level in 50 years and down from 109.6 Mt (120.8 million st) in 1981. The reduced steel demand forced 13 coke plants to shut down. Coal Exports Coal exports in 1982 totaled 96.4 Mt (106.3 million st), 5.7 Mt (6.3 million st) less than in 1981. Despite the worldwide recession and above normal coal stockpiles in many countries, exports were higher than many expected. This showed the relatively strong US position in international coal trade. The US continued to export near-record coal tonnages despite increasingly competitive influences. These included an improvement in Australia&apos;s labor difficulties, the return of Polish coal to Western European markets, and lower oil prices. In 1982, US port facilities were improved and expanded, and more efficient methods for scheduling foreign vessels were implemented. As a result, high volume coal shipments to US ports were routinely loaded and dispatched unhampered by bottlenecks that plagued East Coast ports in 1981. Appalachian coalfield production declined 1.4% from 1981 output and 3.9% from 1980 output. The interior region of the US showed an increase of 7.8% in production. This was primarily because of a

Jan 5, 1983

By K. L. Kayler

Ball clay production in 1991 amounted to about 800 kt (880,000 st), about the same as in 1990. 1992 estimates show a 5% decrease to 750 kt (827,000 st). This decrease continued a trend of reduced production that began after the peak of 900 kt (1 million st) that occurred in 1988. Use of ball clay in sanitary ware was about 2% less in 1992, although levels of use in floors and wall tile, dinner ware and pottery remained constant. Filler, extender and binder applications continued to be important end uses, accounting for about 17% of total market. Refractory uses maintained their market share of about 17 kt (18,700 st). Use of clay liners in toxic and waste dumps is an application widely found in Germany. However, its use has not been fully exploited in the United States. This could represent an opportunity for domestic clay producers. Tennessee remained the leading source of ball clays. Other producers were Indiana, Kentucky, Mississippi and Texas. Tennessee&apos;s production, however, decreased about 3% in tonnage produced and its value dropped from 68% to 65% of total production. The ceramics division of Southern Clay Products, Inc., was bought from LaPorte plc by United Clays of Texas, Inc., a US subsidiary of Watts Blake Bearne & Co. The purchase included ball clay reserves at Troup, TX. The acquisition makes United Clays the second largest ball clay producer in the United Sates. United is also the only company mining clay in Texas. Fire clay production decreased 5%

Jan 1, 1993

By Crystal Poon, Paul Matlashewski, John Morkeh, Kathryn Dorfschmidt, Jose Carvalho, Chad Williams

Rockfall hazards are ubiquitous in mining environments making their control critical for safe mining operations. The complex processes involved in rockfall events necessitate a probabilistic modeling approach with well-calibrated material properties. The controls designed to mitigate rockfall hazards need to be reliable, efficient, and safe to deploy to meet the constraints present at an active mine. This paper presents an innovative solution to rockfall at Rio Tinto’s Bingham Canyon Mine. The solution incorporates the site-specific calibration and creation of a predictive rockfall model with the design, field testing, implementation, and monitoring of the rockfall controls.

By Crystal Poon, Paul Matlashewski, John Morkeh, Kathryn Dorfschmidt, Jose Carvalho, Chad Williams

Rockfall hazards are ubiquitous in mining environments making their control critical for safe mining operations. The complex processes involved in rockfall events necessitate a probabilistic modeling approach with well-calibrated material properties. The controls designed to mitigate rockfall hazards need to be reliable, efficient, and safe to deploy to meet the constraints present at an active mine. This paper presents an innovative solution to rockfall at Rio Tinto’s Bingham Canyon Mine. The solution incorporates the site-specific calibration and creation of a predictive rockfall model with the design, field testing, implementation, and monitoring of the rockfall controls.

By G. Pan

The production data of many mines have not reconciled geostatistical estimations based on exploration and development drilling. The discrepancies in recovered metals are sometimes as large as 30%. A number of factors are responsible for such unpleasant outcomes. A major cause, however, is the lack of geological controls in the implementation of geostatistical techniques. Geological modeling establishes geological constraints and mineralization/ore envelopes. Geological constraints are usually established through drill hole interpretation. Mineralization and ore envelopes have been delineated manually based on assay grades. The issues associated with manual methods are: •Time requirements . •Inconsistent dilution. •Uncontrollable implementation variance. Although the time issue may not be a big concern for some companies, the other two have been responsible for many undesired estimation errors. A new geostatistical approach described in this study is designed on the basis of indicator and ordinary kriging. The central component of the method is the procedure for automatic delineation of mineralization and ore envelopes. The method, referred to as probability assigned constrained kriging (PACK), is demonstrated on a Carlin-type gold deposit. The estimation results are compared to blast-hole based production panels, showing that the estimated tonnage is about 2.1 % higher than the actual production, and the average grade is about 2.4% lower.

Jan 1, 1995

By A. E. Halim, J. F. Brune

Debate continues over whether barricading in refuge chambers is a good strategy to survive entrapment emergencies in underground coal mines, in particular fires and explosions. Unlike U.S. coal mines, Australian coal mines are not required to use refuge chambers and, instead, have adopted a strategy that focuses on instructing and training miners to self-escape to the surface. This paper analyzes the merits and problems of using refuge chambers or self-escape to the surface to manage emergencies in fires or explosions in an underground coal mine. We found that using refuge chambers may not be the best strategy during extensive fires or when multiple explosions occur. In these situations, mine rescuers are unlikely to be able to extract miners who are sheltered in chambers and, conversely, self-escape may save more lives than sheltering. Chances for successful self-escape are further improved by regular, externally assessed training such as the level 1 emergency exercises required in Queensland, Australia. These exercises put pressure on mine operators to ensure and maintain the effectiveness of their emergency management system.

By Dwane K. Johnson

INTRODUCTION The small mining company faces the dilemma of how to finance the development of its properties because it doesn&apos;t have the financial resources to pay for the development costs from its own funds and doesn&apos;t have the financial strength which will enable it to borrow the money needed for development. However, with a little imagination and the right set of circumstances, a financing can be arranged for the small mining company. This paper is an attempt to describe the fundamental steps on how such financing can be obtained --in other words--what is required to provide ad- equate capital at a low cost for developing and bringing a mining property into production. Innovative financing follows from this. The basic keys for building and maintaining a successful mining company are "the four M&apos;s": Management, Market, Mine, and Money. The writer believes their order of importance is as presented and each is a building block required in order to obtain the type of financing that best suits the borrower and lender. MANAGEMENT Management must be experienced, highly organized, realistic, able to take advantage of opportunities and fulfill promises. Mine financing requires a variety of skills and concentration on the part of management. Management should have a thorough understanding derived from experience in geology, construction, mining and metallurgy and environment, marketing, and financial matters. Management must realistically visualize what will be produced at what cost and truly evaluate the risks associated so the proper security can be correctly designed. Since risk cannot be eliminated, the objective of management is to identify the risk which will be present in a given venture and assess the level of that risk which will be acceptable to the firm. Generally the risk which is present is subject to little or no modification. After management identifies and measures the acceptable risk the firm will proceed in a way that it will be least exposed. Management must determine its long-term objectives and strategies within the context of a constantly changing world. This question must be addressed before examining the sorts of risk which affect the development and operation of a specific property. The compilation and interpretation of "hard data" by competent people is good to a point but the experience and instinct of seasoned individuals are the important factors in management choosing a long-term direction for the corporation. The attitude towards risk greatly affects the goals of the corporation. Major risks in a mining project can be placed in four categories: 1. Market - Price, demand, substitution. 2. Costs - Capital, operating, financial. 3. Regulation. 4. Taxation. The feasibility study for a project is the fundamental tool used in the management of risk. Management should employ an experienced team with an established and well-understood set of ground rules for the preparation and assembly of a feasibility study. The necessary degree of realism is built into all levels of the study and if the project is technically feasible, the company&apos;s hurdle rate is then used to discount the base-case project cash flow in order to determine its financial viability. Understanding the geological significance of the mineral deposit is critical. There should be strong interplay among the pure regional geologist, the detailed mine geologist, the mining engineer, and the metallurgical engineer. The collaboration among these different disciplines will yield a feasibility study that is more reliable. The essence of this work must be appreciated and understood by the executives planning the financing. It is vital that they thoroughly understand the risks and make the proper risk assessments to cope with our rapidly changing market environment. Projecting future revenue values is paramount and is subject to much estimation. One way to mitigate fluctuations and the risk of falling prices is by selling production for future delivery. MARKET Since mining is a worldwide industry it is mandatory that bankers be aware of what is occurring in the marketplace, both foreign and domestic. The marketing of the production is a very important facet when considering financing for the small

Jan 1, 1987

By Glenn Mongillo

Discrete Element Method (DEM) software has been successfully used to simulate various machine/soil interactions and provide insight for industries such as mining and bulk material processing. This paper will investigate typical calibration techniques used in particle models for DEM simulation and physical calibration experiments with soft ground TBM cutting tools to incorporate parameters such as tool drag forces that contribute to required TBM torque. With a well calibrated DEM model, it is expected that TBM simulation results will be more meaningful and provide better insight into TBM performance, power requirements, cutting tool placement, and overall cutter head design.

Jun 13, 2021

By E. W. Geist, W. J. Bronkala

PRINCIPLES OF MAGNETIC SEPARATION The application of magnetic separators relies on the different behavior of individual mineral particles under the influence of magnetic forces. When exposed to a magnetic field, all materials are affected in some way. According to whether materials are attracted or repelled by the magnetic field, they are designated paramagnetic or diamagnetic, respectively. Paramagnetic materials are attracted along lines of magnetic force from points of lower magnetic field intensity to points of higher magnetic field intensity. The very strong response of some materials to a magnetic field is sometimes designated ferromagnetic and the particles attracted frequently retain magnetic properties after the applied magnetic field is removed. Diamagnetic materials are repelled along the lines of magnetic force from points of high magnetic intensity to points of lower field intensity. Only limited commercial use of diamagnetic effects has been made. For practical applications, the paramagnetic groupings are: 1. Strongly magnetic (ferromagnetic) 2. Magnetic 3. Weakly Magnetic 4. Non-magnetic The limits of these groupings are not well defined and will vary in some mineral species. Only a few minerals are ferromagnetic (magnetite is an example) and arbitrarily some investigators have selected 10,000 gauss, or 1 Telsa, as the dividing line between low and high intensity magnetic fields. I. S. Wells has developed a table indicating the magnetic intensity required to separate a selected grouping of minerals which is shown in Table 1 on page 2. A similar table has been developed by Carpco Inc. of Jacksonville, Florida in conjunction with the use of its high tension separators. This table, Table 2 on page 3 shows other minerals grouped in the broader categories cited above. Magnetic separation methods are used either to separate valuable minerals from nonmagnetic waste or magnetic impurities or other valuable magnetic minerals from bulk nonmagnetic values. Magnetically susceptible mineral particles occur as either individually discrete particles,

Jan 1, 1986

By Robert A. Jankowski, Charles A. Babbitt, Natesa I. Jayaraman

Today, approximately 31% of underground coal mining operations have designated occupations or areas with more stringent (below 2.0 mg/m3) respirable dust standards in place. Many U.S. coal mines have been able to maintain compliance with very low dust levels, and the Bureau of Mines, in an effort to identify those factors contributing to low dust levels, completed a survey of twelve continuous miner sections which were able to maintain their dust levels at or below 0.5 mg/m3. The quantity and quality of face ventilation appeared to be the most important factor in controlling dust exposure. The results directed Bureau research towards identifying improved face ventilation techniques for reducing quartz dust levels on continuous mining operations. This research has involved the evaluation of a half-curtain face ventilation technique which reduces the cross-sectional area of the entry, thus increasing the air velocity over the operator. The Bureau has also conducted extensive laboratory studies to compare tubing versus brattice, including an evaluation of both systems in a crosscut turn. In an effort to improve ventilation and reduce dust exposures of roof bolter operators working downwind of the continuous mining machine, the Bureau has evaluated two novel face ventilation systems. The first system consists of a fan discharge tubing technique which routes dusty air away from the return entry being bolted. In a technique similar to the fan/tubing concept, exhaust air from the upwind continuous miner face can be scrubbed using a dust collector to capture a portion of the dusty air, clean it, and supply it to the bolter operators as a split of clean intake air. A better understanding of face ventilation techniques should lead to solutions to the problem of more stringent dust standards due to quartz.

Jan 1, 1989

By W. N. Key, L. C. Acton

Freeport Minerals Co.&apos;s Ertsberg East underground operation typifies the cliche that all the "easy" ore deposits have already been found. Despite its location, in a remote Indonesian rain forest, and the effort and expense required to develop the ore body, the mine was developed on schedule, under budget, and with minimal disruption of the adjacent open-pit mining operation. Development of the Ertsberg East copper, gold, and silver ore body took less than two years after exploration drilling and feasibility studies were completed. In addition, the project came in well under its targeted budget of $101.5 million. Initial block caving and underground ore production took place last year. About 3 kt/d of Ertsberg&apos;s total 8.6 kt/d ore production is currently mined underground. This will increase to 5.4 kt/d by year&apos;s end. Underground operations will eventually account for all of Ertsberg&apos;s production, as the open-pit ore body is depleted. Freeport Minerals is currently studying the possibility of increasing total Ertsberg East production tonnage to 10.5 kt/d by 1983. The equipment, work practices, and development methods at Ertsberg East (Gunung Bijih Timur or "GBT"), while typical of other block caving mines, were modified for rapid mine development and maximum ore recovery. Located in the Irian Jaya province, "Gunung Bijih" is the Indonesian expression for the Dutch "Ertsberg" that in English means "ore mountain." "Timur" means "east" and relates to the fact that the new underground ore body lies about 1 km east of the open pit. The area surrounding GBT is mountainous, with peaks from 4.2-5 km. The underground mine adit and surface plant are located at a 3.6-km elevation. The mine, 4° south of the equator, gets 5.1 m/a of rain, but has an average daily temperature of only 13°C because of the mine&apos;s elevation.

Jan 7, 1981

By K. R. Weller

In recent years, a variety of new or substantially modified grinding machines have been offered to the mining industry with claims of improved performance relative to standard grinding machines especially rod and ball mills. The incentive for developing such new machines is high, because costs associated with grinding are a very substantial part of the total costs of processing run-of-mine ore, and gold ores are no exception in this regard. The incentive is also high because of the very low conversion of input energy to comminution energy in most tumbling mills. If the most energy-efficient means of mechanical size reduction is slow compression of single particles, then this energy amounts to only about 3% of that used in tumbling mills. It would seem, therefore, that there is a huge potential to do better. This paper examines three types of grinding machine for which claims of higher energy utilisation ( amongst other beneficial claims) have been made, namely the high pressure grinding rolls, the vibrating drum mill and various styles of stirred mill. It presents evidence concerning the claims, examines the range of particle size and particle size reduction over which benefits might reasonably be expected to accrue, discusses the major issues in contention and briefly describes the research the CSIRO Division of Minerals has in progress, both independently and collaboratively, the latter mainly with the Julius Kruttschnitt Mineral Research Centre (JKMRC) via the Cooperative Research Centre for Mining Technology and Equipment (CMTE) and the Australian Mineral Industries Research Association (AMIRA). There are many criteria which may be chosen to assess relative performance of grinding machines. Those used below are:

Jan 1, 1995

By Sotiris N. Kamenopoulos, Zach Agioutantis

Rare earth elements (REEs) are considered critical minerals for the industrial and defense sectors. In 2018, the U.S. Department of the Interior presented the final list of critical minerals that are vital to the U.S. economy and defense [1], which included REEs among other mineral commodities. REEs are not rare, despite their name, but economically viable deposits of REEs can be found only in certain geographical areas, and the political and social conditions characterizing these areas may not always be in favor of mining operations. Mining operations may be placed in great operational and financial risk if operations are planned in such areas. Erroneous decisions by decision makers may lead to a chain of events that can completely shut down a mining project.