Search Documents

By N. Damiano, J. Noll, C. Zhou, J. DuCarme

"Preventing machine-related injuries is one of the major safety concerns in underground coal mines. Severe injuries and fatalities occur when a miner is struck, crushed, or pinned by mining equipment such as a continuous mining machine (CMM), shuttle car, or a scoop. Proximity detection systems (PDSs) have been applied in mining to reduce these types of injuries and fatalities. All of the PDSs that are currently approved by the Mine Safety and Health Administration (MSHA) for use in underground coal mines are magnetic-field based and could be affected by metallic objects such as trailing cables. Researchers from the National Institute for Occupational Safety and Health (NIOSH) investigated the influence of trailing cables on the performance of PDSs. In particular, the magnetic field coupled from proximity system generators to a de-energized trailing cable were characterized. The results show that significant energy can be coupled from the proximity system generators to a trailing cable when there is a closed loop in the cable. The effect on PDS performance from the magnetic field radiated around an energized trailing cable was also quantified for different current amplitudes in the cable. It is shown that the magnetic field caused by the electric current in the trailing cable mainly consists of a 60-Hz signal and its harmonics which cause little interference to the PDS. The results presented in this paper can help PDS manufacturers to design better systems that are more immune to these effects. INTRODUCTION An average of 250 injuries occur every year during operation of Continuous mining machines (CMMs), and 43 miners have been killed by striking or pinning accidents involving CMMs in the U.S. from 1984 to 2015 (Mine Safety and Health Administration, 2015). In addition, there have been 10 fatal accidents involving mobile haulage equipped with trailing cables from 2000 to 2015 (Noll et al., 2017). In response to these fatalities and injuries the Mine Safety and Health Administration (MSHA) promulgated a regulation in 2015 requiring the use of a proximity detection system (PDS) on all CMMs except full-face machines and proposed a regulation in 2016 which would require a PDS on other mobile underground equipment. Current PDSs approved for underground use are magnetic-field based. The PDS contains machine-mounted magnetic field generators that create fields around the machine. The other part of the PDS is a miner-wearable component (MWC) that reads the flux density of the generators. These systems use the magnetic field strength readings from the MWC to determine whether a miner is at a safe distance from the machine. A stable magnetic field is essential for the accuracy of the system."

Jan 1, 2018

By Joyce A. Ober

Strontium occurs commonly in nature, averaging 0.034% of all igneous rock; however, only two minerals, celestite and strontianite, contain strontium in sufficient quantities to make its recovery practical, and these minerals are found in sedimentary rocks. Of the two, only celestite has been found to occur in deposits of sufficient size to make development of mining facilities currently attractive. Celestite, the most common strontium mineral, consists primarily of strontium sulfate (SrSO,). Strontianite, the second most common mineral, consists primarily of strontium carbonate (Sr CO3). Strontianite would be the more useful of the two common minerals because strontium is used most commonly in the carbonate form, but few deposits have been discovered that are suitable for development. The physical properties of strontium ores are listed in [Table 1].

Jan 1, 1994

By Y. S. Kim, A. Bailey

A feasibility seismic refraction and reflection field survey was conducted at the U. S. Borax Company open-pit mine, Boron, California by the writers during the weekend of March 13 and 14, 1976. This field survey was carried out as a preliminary investigation primarily for the purpose of evaluating and establishing the ability of such geophysical techniques to locate and outline the subsurface openings of the old room-and-pillar mining under the present open-pit. The value of such knowledge about the old underground workings is directly related to the safe and economical operation of the open-pit mine for the company. Although mine maps of the old underground workings are available at the mine, the extent of roof and wall cavings and the present condition of the old underground openings are unknown. Owen and Suhler (2) are the first investigators who used electromagnetic methods, Pulse-Echo System, and electric resistivity measurement to solve the problem without success. A few years later, Herzig and Owen (1) attempted to solve the problem with application of earth resistivity measurement method with unfavorable results. The U. S. Borax Company carried out an extensive study for slope failure problems of the open-pit with application of dipmeter measurements. However, the slope stability study was not correlated to the old underground openings lying under the present open-pit (3).

Jan 1, 1977

By James G. Donovan, Mario G. Karfakis

A large percentage of Southern Appalachian coal reserves are located in seams less than 36" thick. As thicker and currently more mineable deposits are exhausted, methods of underground thin-seam extraction must be developed. Past experience with highwall mining of thin-seam coal has indicated that recovery rates tend to be lower than in conventional operations. It is suspected that this will also apply to underground thin-seam mining, regardless of proposed technology or mining method. Backfilling is one alternative for thin-seam coal mining; although backfill has been used extensively in hard rock mining its use in coal mining has been limited. The ability of backfill to provide additional ground support may enhance coal recovery by allowing for the design of undersized pillars. Backfill is capable of providing additional ground support by restricting lateral deformation of surrounding coal pillars and roof. This additional support can result in significant increases in recovery from thin-seam coal deposits. However, the overall feasibility of backfill is dependent on the in situ behavior of the fill material, the properties of the fill, the effects of the filling method on the total mining operation, and the cost of filling per extra ton of coal recovered.

Jan 1, 2001

By Jae-Chun Lee, Sadia Ilyas

"The present study was carried out to develop an economically feasible and environmentally friendly technique to extract metals such as Al, Fe, Cu, Zn and Ni from electronic scrap by employing Penicillium chrysogenum strain KBS3. Studies were carried out in various leaching modes, including one-step leaching with combined growth and leaching phases (Mode 1), two-step leaching with alternative growth and leaching phases (Mode 2), spent medium leaching with separated growth and leaching phases (Mode 3), leaching with fresh growth medium without fungal culture (Mode 4), leaching with deionized water (Mode 5) and leaching with commercial organic acids (Mode 6). The main lixiviants produced in leaching Mode 1 were citric, tartaric, oxalic and gluconic acids in concentrations of 12, 2.5, 1.8 and 152 mM, whereas in leaching Mode 2, the concentrations were 15, 0.5, 1.0 and 1,162 mM, respectively. In leaching Mode 3, 63 mM citric acid, 23 mM tartaric acid and 29 mM oxalic acid was observed. At 5% pulp density, both leaching Modes 1 and 2 showed similar metal extraction yields from the electronic scrap at 35º C. Approximately 96% Al, 98% Zn, 48% Cu, 25% Fe, 66% Pb and 73% Ni were extracted in leaching Mode 1 in 14 days. In leaching Mode 3, 85% Al, 81% Zn, 97% Cu, 22% Fe, 50% Pb and 63% Ni were extracted in 14 days. The extraction yield of Cu was much lower in leaching Modes 1 and 2 (48- 50%) than in leaching Mode 3 (97%), as well as in leaching Mode 6 (98%) with organic acids, including citric, tartaric, oxalic and gluconic acids.IntroductionTechnical innovations in electrical and electronic equipment with new functionalities and designs stimulate consumer purchasing and lead a rapid increase in the production of waste materials. Terazono et al. (2006) have reviewed the data on electronic waste generation in different parts of the world. Studies by Bertram et al. (2002) have also affirmed that waste electrical and electronic components are the fastest growing waste category, which emphasizes the need for efficient recycling strategies. The recycling of electronic waste is an important subject, not only from the perspective of waste treatment, but also from the perspective of the recovery of valuable materials. However, the recycling of electronic scrap is still limited, due to the heterogeneity of the materials present in the products (Veit et al., 2005).Bioleaching-based processes offer a number of advantages over conventional pyro or hydrometallurgical methods (Lee et al. 2007; Lee and Pandey, 2012). These advantages include simple, inexpensive (in some cases) and ecofriendly approaches and the generation of less active leach residue relative to other metallurgical processes. Although biohydrometallurgical processes have been successfully applied to the leaching of metals from ores (Olson et al., 2003; Rawlings, 2002), data pertaining to the application of these processes for the extraction of electronic scrap are still scarce. Recently, a few studies have been undertaken for the extraction of metals from electronic scrap/ printed circuit boards (Brandl et al., 2001; Faramarzi et al., 2004; Ilyas et al., 2007; Ilyas et al., 2010). These studies were conducted with mesophilic chemolithotrophic bacteria (Acidithiobacillus ferooxidans and Acidithiobacillus thiooxidans), cyanogenic bacteria (Chromobacterium violaceum) or moderate thermophilic bacteria (Sulfobacillus thermosulfidooxidans). However, compared to bacterial leaching, fungal leaching has several advantages, including (i) the ability to grow at a higher pH, thus making it more suitable for the bioleaching of alkaline solid waste; (ii) a generally faster leaching process with a shorter lag phase and (iii) the chelation of excreted metabolites (e.g., organic acids) with metal ions, thus reducing toxicity to the biomass (Burgstaller and Schinner, 1993; Aung and Ting, 2005)."

Jan 1, 2015

By Stephen R. Brown

The principles of quality management are well developed and, from a practical stand- point, thoroughly implemented in the process industries of Japan. Although these principles are now applied to the U.S. manufacturing industry, and as a result, the steel industry, they have been largely ignored in the non-ferrous and precious metals industries. This paper presents the concepts and practical approaches to implement a total quality management program. Contrary to the beliefs of many managers, such a program increases yields, recoveries and output while it decreases unit costs. In fact, quality management incorporating statistical process control will be an essential ingredient for metallurgical plants to effectively compete in the '90's.

Jan 1, 1991

By Travis S. Wellman, Jon C. Volkwein

The Bureau of Mines conducted a study to assess the impact of a directional water spray system on a unique single inlet dust scrubber on a low profile mining machine. Tests were conducted in a full scale model mine using a Joy 12 CM 10-AA continuous mining machine. Tracer gas was introduced at the face and concentrations of the tracer gas were monitored at the face and in the return. Various parameters included: mining position, depth of cut, brattice setback and combinations of scrubber, directional sprays or symmetrical sprays. Results indicated that either directional or symmetrical water spray configuration improved the ventilation effectiveness of the scrubber by a factor of 2 to 3. Average face ventilation effectiveness (FVE) values for all testing of the scrubber and directional sprays were 0.95, versus 0.37 for a standard 6 m (20-ft) blowing curtain without sprays. No FVE values were less than the standard 6 m (20-ft) blowing results.

Jan 1, 1989

By James M. Reichman

Waterjet assist of mechanical cutters has been demonstrated in a variety of laboratory studies as well as on field equipment. As this technique becomes more widely accepted, it will be necessary to develop methods of minimizing the horsepower and water requirements. In machines such as roadheaders, continuous miners, and longwall shearers, the use of waterjet assist can be optimized through the development of phasing valves. Phasing valves will allow only the cutters in contact with the rock to be assisted. Since only 30 - 40% of the cutters are in contact with the rock, the saving power is significant. Flow Industries has developed a phasing system for use on roadheading machines. This system allows the operator extensive control of the angle of assist as well as the quadrant being assisted. This system could be greatly simplified for production machines and adapted for use in continuous miners and longwall machines.

Jan 1, 1985

By Boris M. Vorobjev

The paper in question discusses a wide range of topics related to computerized coal mine monitoring systems starting with the history of development and application of computerized monitoring coal mine systems and finishing with modern trends in the design and updating of such systems. The paper focuses exclusively on methodological and technical aspects of computer-based coal mine monitoring systems and their applicability in both surface and underground coal mining operations.

Jan 1, 1989

By P. Chauvet

From a computational point of view calculating a variogram is a perfectly simple operation. For any particular study, we know which variable is to be studied. We also have a good idea of structural parameters which are likely to be important (the scale of the phenomenon, the probable direction of the anisotropy, etc.). Finally, we know the structure of the data file. So we can specify the parameters to be used to calculate the variogram (the distance classes, the angular classes, etc.). This allows us to decide which variogram program is most appropriate (1, 2 or 3 dimensional data, regularly or irregularly spaced, etc. ) . In general, the basic statistics (mean, variance, correlation? etc.) have been calculated beforehand, and so the distribution of the data is already known. Consequently, the choice of the parameter values fed into the variogram is by no means arbitrary. But it must nevertheless be made before the' variogram is calculated. If the resulting variogram is not satisfactory, the whole sequence of operations has to be repeated. Before going on to see how this can be avoided, it is worthwhile having a brief look at the common causes of "unsatisfactory" variograms.

Jan 1, 1982

By Lynn Salvati, Colin LaVassar, Loic Galisson, Joel Theodore, Lynette Sla

"Sound Transit’s University Link and Northgate Link projects will add 6.75 miles (10.9 km) of twin-bored tunnel to Seattle’s light rail system, extending the route north from downtown Seattle. The tunnels are being constructed primarily in glacial soils using pressurized-face tunnel boring machines. Cover over the tunnel alignment varied from 13 feet to over 300 feet (4–91 m). Since the tunnels are located in densely populated urban areas, controlling ground movements and monitoring settlement were essential to success of these projects. Hundreds of geotechnical instruments, including extensometers, surface settlement points, and near-surface settlement points, were used in both projects to monitor settlement. The observed data were compared to settlement predictions made prior to tunneling, and analyses performed to update empirical factors to better estimate settlements. Recommendations for designing efficient and cost-effective settlement monitoring programs are provided based on the review of the monitoring data and analyses.INTRODUCTIONThe paper includes data from Sound Transit’s University Link and Northgate Link projects. These projects will add 6.75 miles of twin-bored tunnel to Seattle’s light rail system. The tunneling for University Link will extend the light rail system from downtown Seattle to the University of Washington. Tunneling from downtown Seattle to the Capitol Hill Station was completed under the U230 contract, and tunneling from the Capitol Hill Station to the University of Washington Station was completed under the U220 contract. The Northgate Link extension will extend the light rail line north of the University of Washington, including approximately 3.5 miles (5.6 km) of twin tunnels between the University of Washington Station and the Maple Leaf Portal and two stations, U District Station and Roosevelt Station. Tunneling for the Northgate Link project is still underway as part of the N125 project. At the time of writing, tunneling from the Maple Leaf Portal to Roosevelt Station has been completed. Therefore data labeled as N125 in this paper only include the portion of the alignment from the Maple Leaf Portal to Roosevelt Station."

Jan 1, 2016

By S. B. Kim, J. Hong, K. Park, W. Kim, H. Kim, Y. Han, J. Choi

"For the first time, the influence of stearyl trimethyl ammonium chloride (STAC) as a collector, on the flotation behavior of lepidolite (Uljin, South Korea) was systematically examined in Denver Sub-A cells. Flotation tests were carried out by varying amount of STAC (50–200 g/ton), feed size (-65, -100, -150, and -200 mesh), and solution pH. The impeller speed of 1000 rpm, flotation time of 10 min and AF-65 (a frother) of 250 mL/ton were invariably applied. In order to complement flotation experiments, zeta potential measurements and XRD analysis were conducted. XRD results showed that the ores were mainly composed of lepidolite, muscovite, quartz, calcite and albite. In addition, zeta potential results showed that isoelectric points were about 2.5, 2.3, and 9.7 for quartz, albite, and calcite, respectively, and lepidolite was determined to be less than 2. Overall, the results of 3-stage flotation showed that Li2O grade and recovery tended to increase with increasing STAC dosage and decreasing feed size. In addition, Li2O grade increased with decreasing pH. The results were explained by the extent of the interaction between STAC and each mineral.INTRODUCTION A great number of potential applications of lithium are being developed currently by the thermonuclear fusion power generation industry(1,2) as well as by the battery and fuel cell industry(3). Even though lithium is mainly consumed in the form of lithium metal and some lithium compounds, about 10% of total lithium production is consumed directly as mineral concentrates by the ceramic industry for the manufacture of special ceramics and mica based glass-ceramics(4). Granitic pegmatites normally contain feldspars, quartz, and mica in addition to lithium-bearing minerals such as spodumene (LiAl(SiO3)2), petalite (LiAlSi4O10), and lepidolite (KLi2Al(Al,Si)3O10(F,OH)2). The amount and grade of metallic minerals tend to gradually decrease and become lower, leading to the increase in the price of base metal or metallic compound(5). Accordingly, recent studies have been extensively devoted to developing the technique to improve the grade of metallic minerals from low grade metallic ores(6,7). Nevertheless, studies regarding the improvement of Li grade from lepidolite ores are very scarce. Lepidolite is a phyllosilicate mineral of the mica group and is often associated with other minerals such as calcite, muscovite, feldspar, and quartz, which need to be separated for lepidolite enrichment(8). Many studies have reported the flotation techniques for separating calcite, muscovite, feldspar, and/or quartz from various targeting minerals(9-11); however, there has been no attempt to investigate physico-chemical properties of lepidolite and its separation from such types of gangue minerals through flotation. Hence, in this study, for the first time, flotation has been carried out for the quaternary ammonium salts (stearyl trimethyl ammonium chloride (STAC, (CH3)3CH3(CH2)16NCl))-lepidolite system based on only the electrokinetic property of minerals that consist of lepidolite ores without adding any depressant to get an initial insight on its flotation behavior. The experimental variables that influence the lepidolite flotation such as amount of collectors, feed size and solution pH have been also examined."

Jan 1, 2015

By Hasan Sevim

A computerized heuristic model for an efficient and economic design of belt haulage networks in underground coal mines is discussed. The model is versatile, easy to use, and is valid for all mining methods singly or in combination. It may be used to design new networks or to analyze existing networks. The input data required are 1. maximum production rates from a section, 2. probabilities of production rates, 3. equipment costs, and 4. data necessary for network coding to represent different cases. The objective function is the "expected minimum cost per ton of coal hauled" while meeting production requirements. The output includes belt width, motor horsepower, bin size etc. and also values of operating parameters for each belt such as belt speed, effective tension, power consumption etc. A detailed account of the cost involved is also provided for each unit as well as for the entire network. Description of the model and an example of the design of a belt network in a mine with two longwall and four development sections are presented.

Jan 1, 1986

By X. Nie

A new one-step process was developed to completely eliminate iron and directly obtain pure Ni, Co, and Cu chloride catholyte from nickel rich matte by low temperature (400 0c) chlorination roasting of Ni, Co, and Cu with HCl and leaching with water (PH 7). The effects of roasting temperature, time, oxygen potential and HCI addition and leaching temperature, pH, H2S04 addition and residue sulphur on the recovery of metals and purity of leaching solution were investigated. More than 99 % of Ni and Co and 95 % of Cu in the matte was directly extracted into the solution while 99.995 % of Fe remained in the residue. The iron concentration in the leaching solution was less than 3.6 X 10-5 mol/L.

Jan 1, 1994

By James Warren Andrews

The values of saturated water vapor pressure from steam tables have been found to be inaccurate for mine ventilation usage because the effect of air on the saturated water vapor was disregarded. Presented here are the newest and most accurate currently available tables from the National Bureau of Standards (NBS). Also included are: (1) a formula for correcting the saturated water vapor pressure for temperature and altitude. (2) a formula for computing unsaturated water vapor pressure, and (3) a formula for air density. Because Systeme International (SI) units are used in the formulas, conversions are given from U. S. conventional units to SI units. The intent of this paper is to show by means of six steps the accurate calculation of mine air density for use on modern computers.

Jan 1, 1989

By B. Ceccarelli

Many public domain programs useful in mining engineering, e.g., MULSIM, DZTAB, and EXPAREA, require tedious data input and generate pages and pages of printed output. To eliminate the tedium and to enhance the output, ETI U.S., Inc. developed GEM, Graphics for Engineering and Mining, a collection of application programs and underlying interface tools for VAX/VMS computers. This paper presents an example of how an application program in GEM enhances a specific public domain program. It describes how GEM provides automated graphics assisted input and output. The paper describes how this program uses the GEM User Interface: the 3D GKS device independent graphics, server and drivers, various mining, mathematical and statistical algorithms, the means of handling graphics, data including IGES, and the foreign language interface.

Jan 1, 1992

By C. D. Anderson

A variety of processing technologies exist for recovery from both primary and secondary sources of rhenium. Currently, there are no known primary rhenium deposits; thus, the method in which primary rhenium is produced is dependent on the commodity of which it is a byproduct, e.g., copper, molybdenum, uranium, etc. In addition, focus on the recovery of rhenium from secondary sources, such as alloy scraps and catalysts, is continually growing. This paper presents a review of both primary and secondary processing technologies for the recovery of rhenium.

By D. Kwak, S. Han, J. Kim, Y. Lee

"INTRODUCTION In carbonate rocks, it is difficult to characterize due to the high degree of heterogeneity in pore geometry. Carbonate rocks have various types of pore systems such as fractures and vugs, and this heterogeneity should be considered for more realistic prediction of oil production in carbonate reservoirs. This study carried out water flooding experiments using five carbonate rock samples in order to observe the change of physical properties. Firstly, qualitative and quantitative analyses were conducted for each carbonate samples by use of XRD and XRF to evaluate the mineral content. All samples are mainly composed of CaCO3 and after that, the ICP experiments were carried out for the water passing through the carbonate. As a result, it was possible to measure the quantity of CaCO3, MgO, Fe2O3 component in water and due to this effect, the permeability of carbonate was altered especially in the front part of the core. Finally, after the carbonate was saturated by 30 API crude oil, water injection to enhance the oil recovery was repeated and it was confirmed that the oil-producing characteristics are different depending on the dissolution characteristics of carbonate rock samples. CORE SAMPLE ANALYSIS Porosity and Permeability Experiment Porosity and permeability were measured. The procedures are as follows (Figure 1). 1. Measure the diameter and length of the dry core using Vernier caliper. 2. Put the core in the core holder, run vacuum pump until the inlet and outlet pressure gauge equal. 3. Saturate the core using ISCO pump to inject water at 650 psi 4. Measure the amount of water and calculate the porosity 5. Set up the outlet pressure at 500 psi. 6. The flow rate measure when the equilibrium 7. Calculate the permeability through Darcy’s Law. 8. Cutting of core upstream and downstream about 13cm, and measure the each of permeability."

Jan 1, 2016

By James D. Hervol, Josepph W. III Leonard, Barbara J. Arnold

INTRODUCTION Dry concentration or pneumatic cleaning uses air currents as the separating medium. Pneumatic cleaning in the United States today is limited to three or four operations. In fact, the quantity of bituminous coal cleaned pneumatically has declined from its peak in 1965 of about 25.4 million tons (23.1 Mt) to its current level (1988) of less than 4 million tons (3.64 Mt) annually, as shown in Fig. 7-9 1. In 1940, pneumatic methods accounted for 15% of the bituminous coal and lignite cleaned in the United States as given in Table 7-32. Currently, pneumatic methods account for less than 2%. The largest air plant was built in Pennsylvania about 1968 with 14 units processing 1400 tph (1280 t/h) of 3/, in. X 0 (19 mm X 0) raw feed and two additional units retreating middlings. This same plant is one of only three or four plants still operating air-cleaning devices in the US. A wet plant was added in 1985 to increase the efficiency of cleaning the fines. The air plant is still used as a scalping operation for the coarse material. Five additional operations are either no longer in production or have discontinued the use of air tables within the last year. Wet cleaning methods are now being employed at the facilities that have discontinued air table operation. he advantage of dry cleaning techniques is the low moisture content of the clean coal product. However, to decrease respirable dust, mining operations must use water sprays on modem mining equipment. This water adds to the moisture content of the run-of-mine coal and decreases the effectiveness of dry cleaning processes that rely on low surface moistures in the feed to allow for good separations. Wet cleaning methods are preferred, especially since they also allow for much sharper separations. The advantage of dry cleaning techniques is the low moisture content of the clean coal product. However, to decrease respirable dust, mining operations must use water sprays on modem mining equipment. This water adds to the moisture content of the run-of-mine coal and decreases the effectiveness of dry cleaning processes that rely on low surface moistures in the feed to allow for good separations. Wet cleaning methods are preferred, especially since they also allow for much sharper separations. Despite dry concentration's drawbacks, research has continued into dry concentrating methods, including both electrostatic and magnetic separation techniques. The real application for future dry cleaning processes is probably at the power plant between the pulverizer and the boiler feed where particles are already dry and ground to fine sizes (- 200 mesh [ -0.075 mm]), increasing the effectiveness of the separation and also, possibly, increasing the liberation of clean coal from finely disseminated impurities. From a utility's viewpoint, pneumatic cleaning offers the best delivered Btu cost, based on the premise that a percent of moisture is just as detrimental as a percent of ash. Additionally, several other advantages are inherent in dry concentration techniques. The main advantage is that dry concentration re-

Jan 1, 1991

By P. F. Ziemkiewicz

This project evaluated the performance of nine passive treatment methods by studying 137 treatment units in eight eastern states. Performance was normalized according to construction cost, projected service life and tons of acid load treated. Results were dimensioned as $/tons of acid load treated/year. These costs were then compared to those of chemical treatment. Sites that achieved acid load reductions at costs below those of chemical treatment were considered successful. In addition to evaluating the performance of the treatment methods, this paper describes the various passive treatment systems, their applications and performance data for individual treatment units.

Jan 1, 2003