Search Documents

By J. Hanna, H. R. Gonzalez

Four Ca-bentonitic clays from Alabama were evaluated for use in diammonium phosphate (DAP) or urea ammonium nitrate (UAN) fertilizer suspensions. The viscosity and gel strength of suspensions prepared with different proportions of a Western bentonite clay and sodium-exchanged Alabama clays were measured as a function of clay content and dispersant concentration. The results obtained suggested that three of the Alabama Ca-bentonites would replace about 40% of the more expensive Western bentonite in UAN and DAP fertilizer suspensions. The performance of the Nu-modified clays, prepared according to the Tennessee Valley Authority soda ash method, was as good or even better than those observed for the Mg-, NaIMg- or K-modified clays. The TVA clay modification procedure appears to be reliable and cost effective.

Jan 1, 1991

By Jens Classen, Thomas Kurth, Karl G. Holter

High performance sprayed concrete equipment installed on two 9.4 m diameter hard rock TBMs enabled a continuous sprayed concrete lining for the entire contour in both tunnels to be performed concurrently with the advancing TBMs. Innovative layout of the sprayed concrete arrangements comprised ring beam constructions each with two independent spraying robots. Each of the spraying robots were independently connected to sprayed concrete pumps, as well as a high capacity concrete logistics system on the backup. The mix designs focused on long open-time, excellent pumpability and tough requirements on strength development. The achieved output capacities of the sprayed concrete amounts to an average of 15 m3 per hour. Peak capacities of 24 m3 per hour have been realized.

Jan 1, 2003

By J. Herbst, K. Fallenius, G. Poling

Since 1970 a new series of pneumo-mechanical flotation machines has been developed by Outokumpu Oy. The cells have a completely new type of mechanism based on a recently-developed theory of conditions necessary for dispersion of large amounts of air. The mechanism was developed in 3 cu m cells and scaled to 16 cu m cells. Rotor and stator description, scale-up theory, and practical experience with the 16 cu m cell are presented.

Jan 1, 1976

By K. Hanumantha Rao, K. S. E. Forssberg, H. R. Manouchehri

This paper summarizes the practical considerations of the various electrical separation methods used in mineral processing. The effective factors related to mineral characteristics and equipment attributes are described and analyzed with reference to conventional industrial applications of the electrical methods. Some new aspects of electrical methods application and their potential for mineral beneficiation, apart from the mineral systems that have been successfully beneficiated, are also presented. In addition, wet dielectric separation, which now appears to be promising, is briefly cited.

Jan 1, 2000

By D. H. Steve Zou, Cui Lin

"This paper first discusses the basic attributes of sustainable mining and the responsibilities of various steak holders including mining companies, governments, and engineers. It is followed by a brief overview of the current practice on regulations, inspections, waste management and mine closure planning in Canadian mining industry. A case study is then presented as an example of sustainable mining where mine planning, mineral recovery, environment protection, reclamation and community development were integral parts of the overall strategy. A comparison of the mine site before and after mining is made to demonstrate the ""best practice"" in modern mining.Sustainability in Mineral Resource Development Extraction of mineral resources and other natural resources on the Earth has been and will continue to be an essential activity necessary to support human’s life. We live on the planet and depend on the available resources to survive. The extracted materials form the base to support modern life. However, we must be aware of the fact that mineral resources are limited on the Earth and may not last forever. Every time we extract one ton of materials, there is one ton less. They are not able to regenerate or regrow. One can ask a simple question: How long will they last? Or, is there anything left for our great grandchildren and many generations to come? The answer is not simple. Some minerals have become scarce or about to deplete. Some minerals may last longer. The reserve of a type of minerals depends on what we have discovered and the minable amount depends on accessibility and technology we have. Even if there are minerals in the deep ground, we may be limited by our technological capability. At the same time, we also need to understand the action of mineral extraction from the ground and the consequences of that action. Mineral extraction is a very hard work. We must break the ground to extract the ore, either through surface mining or underground mining. This action means disturbance of the land where we live. The disturbance is much more visible in surface mining than underground mining. The disturbed land, if not properly reclaimed after mining, is not going to be reusable. The very purpose of extracting minerals from the ground is to support our life but the action has a negative impact on our life. How can we reduce and limit disturbance of land from the action of minerals extraction? How can we make the disturbed land reusable? These issues must be properly addressed and a balance achieved."

Jan 1, 2017

By Edward F. Divers, J. Drew Potts

Powered dust-filtering helmets (dust helmets) have become increasingly prevalent in the underground mine environment in recent years. Many longwall operations use dust helmets to reduce the respirable dust exposures of miners required to work downwind of crusher, roof support and shearer operations. While continuous mining sections are usually less dusty, use of diesel equipment represents a new potential health problem. The U.S. Bureau of Mines recently conducted a study to determine the efficiency of a dust helmet on diesel-size particulate. Two underground evaluations were conducted on continuous mining sections that were using diesel haulage vehicles. Model No. AH21 Racal airstream helmets equipped with AS22-3 prefilters, AS23-3 main filters and AS60476 tyvek full-face seals were tested. Helmets were placed on mannequin heads and mounted in the ram car cabs. Andersen Model 298 (eight-stage) personal cascade impactors were used to sample air inside and outside of the helmet. Impactor stages 8 and the final filters were analyzed to determine submicrometer (0 - 0.93 µm) particle concentrations. Results from this study showed that the dust helmet was 94% (± 3% at 95% confidence level) efficient on submicrometer particles. Typically, very little coal dust is observed in the submicrometer size range, therefore, these particles were assumed to be from diesel exhaust. Results from this study indicate that proper use of the dust helmet on continuous mining sections that are using diesel haulage vehicles may be beneficial to the health of miners.

Jan 1, 1991

By John Armstrong, Michael Savill, David Powell

Hong Kong is an intensively developed region and has the highest vehicle densities in the world. In 2000 there were 6.6 million people and 580,000 vehicles using 1,890 km of road covering the 1084 km 2 territory. The high vehicle and population densities together with the difficult terrain have seen road tunnels emerge as key components both in the current and future road transportation network. Currently there are eleven operating highway tunnels in Hong Kong, seven government owned and the remaining four “build, operate and transfer” franchises, see Figure 1. The very first tunnel was the dual two Lions Rock Tunnel completed in 1967and the latest the dual 3 lane Tai Lam Tunnel opened in mid 1998. Figure 2 shows the alignment and statistics for all 11 Hong Kong tunnels. Looking ahead, Hong Kong has embarked on the study and design of the next generation of major highways and as many as a further seven tunnels are currently under feasibility study or detailed design. This seems an opportune year to produce a broad appreciation of the fire strategy, life safety and ventilation practices in Hong Kong not only for the existing tunnels but the new standards and requirements for the next generation of Hong Kong tunnels. This paper provides an overview of the fire strategy, life safety and ventilation of Hong Kong’s existing and planned tunnels. The paper pays particular attention to the areas where the unique conditions and requirements in Hong Kong impacts on tunnel and systems design and the solutions adopted to overcome these challenges.

Jan 1, 2001

By Keshavan Nair

In connection with Project Payette, which is concerned with the detection of underground nuclear explosions, it was necessary to determine the technical feasibility of constructing and maintaining a large (approximately 315 feet in diameter) unsupported underground cavity at a depth of approximately 2700 feet in the Tatum Salt Dome in Mississippi. The dimensions and the location of the cavity in the salt dome were governed by criteria laid down by the Atomic Energy Commission. Within the framework of the specified criteria, cavities of various shapes and dimensions could be utilized. One aspect of the feasibility study was to investigate the structural stability of various cavity shapes and to recommend a preferred shape. This paper summarizes the studies that were conducted to evaluate the structural stability of various proposed cavities.(l)

Jan 1, 1968

By Donald R. Williamson

Statistical studies at Cyprus Pima Mine indicate that samples from 22 blastholes are necessary for determining average copper grades, within a desired range of precision, for mine-model blocks by arithmetic averaging. The average number of holes in such blocks is 14. Many considerations show that more holes will not be drilled for sampling. A way to determine block grades more reliably than by" arithmetic averaging was sought. Thus far arithmetic averaging has proven to be the best procedure for the particular operation characteristics despite the small number of samples. It naturally follows that expenditure of great effort in sampling blasthole cuttings is unwise.

Jan 1, 1977

By Cory Dippold, Michael Mett, Jérôme Steinkühler, Kristi Latimer

For decades, tunnels of all types have been a significant part of our infrastructure. In particular, water tunnels carry millions of gallons of fresh water every day to major metropolitan areas and surrounding communities. As a critical piece of public health infrastructure, it is important to inspect the condition of these tunnels regularly to ensure reliable and continuous operation. A specific challenge with water infrastructure is that it’s often difficult or impossible to shut down the system for long periods of time to perform the needed inspections. The latest method of tunnel condition assessment is the use of hybrid reality 3-D scan data. Photogrammetric and LiDAR based 3-D data ensure a reliable and objective view of tunnel conditions. The data can be used to support a detailed digital inspection including the compilation of databases that consist of a wide variety of deficiencies such as cracks and spalls within the structure. Mott MacDonald, a design engineer company worked closely with Dibit, used a 360-degree scanning system to collect high-resolution photogrammetric and LiDAR data on a recent project involving a water tunnel. The allows for full 360-degree coverage of the tunnel surface including a water covered invert. It operates at walking speed and ensures a fast and reliable data acquisition which can reduce the time of tunnel shutdowns. Several allocated inspection weeks can reduce to few days, with the final work product being a higher quality and more complete deliverable than traditional inspection methods would have provided. The true-color 3D-model has a photo resolution of 1 × 1 mm (0.039 × 0.039 inches) which makes cracks visible with a width of down to 0.3 mm (0.011 inches). The assessment of water tunnels, its technical challenges and the results of the 3D-tunnel inspection case study are illustrated and described in this publication.

Dec 1, 2022

By Steven W. Hunt, Steven B. Fradkin, Roger J. Maurer

During the 1980s and 1990s, twenty deep shafts were constructed in Milwaukee to depths from 85 to 91 m (280 to 300 feet) through soil and weak rock thicknesses ranging from 37 to 69 m (122 to 227 ft). Adjacent compressible soils, settlement sensitive structures and high groundwater levels required that shafts be constructed without dewatering. Contractors attempted several methods of ground support and groundwater cutoff. Significant problems developed during construction of 11 of the 20shafts. One shaft collapsed; groundwater blow-ins occurred at five of the shafts; and seepage caused unfrozen windows at three of the freezewalls. Ultimately, combinations of grouting and ground freezing were utilized to complete all of the shafts into bedrock. This paper discusses the main design and construction challenges experienced and the lessons learned.

Jan 1, 2003

By W. Jacobi, K. Eisfeld

The primary objective of dosimetric modelling for the inhalation of radon daughters is the evaluation of the dose distribution and of the mean dose to sensitive cells or target tissues in the respiratory tract which are assumed to be responsible for the initiation of lung cancer. The results of such dosimetric models are influencing the practice of radiation protection in a twofold manner: Firstly, they enable us to identify appropriate operational quantities for air monitoring and for the surveillance of individual exposures to radon daughters. Secondly, they can be used to derive secondary and operational limits for these radionuclides from the basic dose limits. The dose to target tissues in the lung from inhaled radon daughters depends on various physical and biological parameters: The unattached fraction of daughter atoms, the AMAD of the carrier aerosol for attached atoms, the geometry of the respiratory airways, the breathing conditions, the parameters for the retention and translocation of daughter atoms in the different lung regions, and the location of the target cells or target tissues, respectively. Therefore, dosimetric modelling for radon daughters has to include a sensitivity analysis showing the influence of these parameters. To meet these objectives we have recently described in a comprehensive report an improved dosimetric model for the inhalation of 222Rn, 22ORn and their short lived daughters (Jacobi and Eisfeld, 1980). In the following this model is shortly described and the main results are summarized. DOSIMETRIC MODEL [Model Structure]. For the geometry of the bronchial airways the model A of Weibel (1963) was used. Each bronchial generation i (i =0.1 .... 16) was considered as a separate compartment i, for which the following transfer pathways for radon daughter atoms were taken into account (see fig. 1): (1) the uptake by deposition (deposition probability wi); (2) the translocation by ciliary clearance (rate constant [A]i); (3) the transfer to blood by diffusion through the bronchial epithelium (rate constant [A]b). To distinguish between attached (Index a) and free (index f) daughter atoms each bronchial generation was divided in two subcompartments (i.a and if) with a transfer rate constant [a]s (ia- if) characterizing the desorption or dissolution rate of attached atoms in the mucus fluid. Thus for daughter atoms primarily deposited in attached form the transfer to blood is a twostep process with the rate constants [a]s and [A]b which were assumed to be independent of the generation number i. [Deposition]. The deposition probabilities wi in each bronchial generation were calculated on the basis of the laminar diffusion model of Gormley et al. (1949); however the deposition in the upper airways was corrected for turbulent air flow, taking into account the results of our deposition experiments (Martin et al., 1972). Figure 2 shows the resulting deposition probabilities per unit surface area of the bronchial generations for nose breathing at a rate of 20 1/min. The values for attached daughter atoms refer to an AMAD of 0.2 - 0.3 µm ([O]g =3) for the carrier aerosol; the deposition values for free atoms were derived with a diffusion coefficient of 0.05 cm2/s, assuming a prefiltration of 50% in the naseopharyngeal region.

Jan 1, 1981

By A. D. Hammond

"INTRODUCTION The recent drop in iron ore prices has claimed an unwitting casualty in vanadium. Vanadium is dominantly produced as a co-product of steel production. The recent shutdown at EVRAZ’s Mapochs steel-vanadium operations in South Africa has cut-off 10% of the world’s vanadium output. Earlier in February, 2015, Australia’s Atlantic Ltd. suspended operations at its Windimurra iron-vanadium complex after a fire caused severe damage at the plant. Since then, challenging market conditions has resulted in the permanent closure of this operation. This decoupling of vanadium production from integrated iron ore producers presents an opportunity for vanadium exploration companies to target single-product deposits. This trend is manifested in the increasing number of pure-play vanadium ventures around the world.The mine production of vanadium is dominated by three countries namely, China, South Africa and Russia, which collectively produce 98% of the world’s vanadium. While the use of vanadium as an alloy in the steel industry remains by far the largest application for this metal, growth in demand is expected to come from the renewable energy industry in the form of batteries for energy storage. This paper summarizes the current state of vanadium exploration, briefly describes the vanadium market and lists sources of future demand for the metal. TREND IN VANADIUM EXPLORATION The most active participants in the current vanadium exploration are pure-play vanadium ventures in Brazil, South Africa and Australia. These ventures are targeting deposits with higher vanadium grade than those typically mined in titaniferous magnetite operated by integrated steel-vanadium producers. The 10% shortfall in vanadium production resulting from the shutdown at EVRAZ’s Mapochs is expected to be partially compensated by Largo Resources’ Maracás Menchen vanadium operation located in the State of Bahia in Brazil, which commenced operation in August 2014 and is expected to reach design capacity of 11,400 tonnes of vanadium pentaoxide (V2O5) by the end of 2015. The estimated production1 for 2015 is 6,500 tonnes of V2O5 at a target production cost of $3.60/lb. This is the first vanadium operation to be placed in production in the Western Hemisphere in over 35 years."

Jan 1, 2016

By Donna L. Boreck

In an effort to increase recovery in thick and closely spaced coal seams, the Bureau of Hines, U.S. Department of the Interior, is studying the feasibility of introducing three mining methods-high-face longwall, multi-slice longwall, and longwall caving-in western coal operations. Geology plays a significant role in determining the success of such methods. Some of the factors that will affect development are as follows: (1) thickness and three-dimensional configuration of the seam, (2) cleats, joints, and fractures in the coal and roof rock, (3) roof composition and variability, and (4) coal quality and changes in quality within the seam. Through geologic mapping, the presence of many of these factors is predictable prior to development.

Jan 1, 1987

By Richard J. Fantel

The U.S. Bureau of Mines performed engineering and economic analyses on 130 domestic phosphate mines and deposits, all containing demonstrated resources, of which 73 are in the Southeastern states of Florida and North Carolina, to determine the domestic availability of phosphate rock. Of the total domestic resources studied (6.4 billion tons of recoverable rock) over 60 percent is found in these two Southeastern states. At an estimated cost of $30 per ton, in January 1981 dollars, approximately 1 billion tons of rock is potentially recoverable from Southeastern deposits, increasing to 3 billion tons at $45. In addition, there is nearly 6 billion tons of recoverable rock at the inferred level (some presently unmineable) in Florida and Georgia.

Jan 1, 1983

By Clarence O. Babcock

A simple robust rock bolt load gage was tested in the laboratory to define its characteristic behavior and to obtain a measure of its performance. The gage uses three vibrating wire sensors crimped 120 degrees apart into the outer surface of a hollow cylindrical steel tube. The resonant frequencies of the wires change as the gage is loaded. This change is read with a Creare meter developed for the Bureau on a previous contract to read borehole stress gage results. A statistical analysis of data obtained defines the variables influencing results. A U. S. patent (3,914,992) assigned by the author to the Department of the Interior was granted October 28, 1975.

Jan 1, 1976

Underground mining has the potential to be one of the more dangerous industries in the United States and the world. Following recent disasters in Sago, WV; Darby, KY, and Crandall Canyon, UT, the mining industry was reminded of the need for a system to allow trapped miners awaiting rescue to survive following a disaster. To address this need, Battelle has developed a Mine Barrier Survival System (MBSS) that surpasses all current technologies and sets a new standard for keeping miners alive in the event of a fire, flood, explosion or collapse. The MBSS creates a temporary refuge for miners who cannot escape by using inflatable barriers and a post-fire atmosphere scrubbing system to define the ?safe haven? and remove CO2 and CO while replacing oxygen and providing heat. Current personal-protective systems in use are designed to provide breathing air for only a few hours when, realistically, it may take days for rescue teams to reach trapped miners. Battelle?s MBSS is designed to aid up to 15 miners for four days.

Jan 1, 2008

By R. L. Wooten

When discussing what Coal Mine Safety in the future will be, it is important to examine three areas which at present provide significant parameters to the industry. These three areas are: 1) Safety improvements in mining equipment; 2) Labor-management relations; and, 3) The politics of coal mine safety. EQUIPMENT Over the past several decades significant safety improvements have been made in the types of equipment now in use in most operations. Many of these improvements have evolved through mandates from either the U. S. Bureau of Nines, MESA, MSHA; and in some instances, the states. Cabs and canopies are examples of federal mandates while the use of ATRS initially was a state mandate.

Jan 1, 1985

By E. Watkins, V. Gangrade

Large-opening stone mines often rely on natural ventilation and a network of auxiliary fans to produce adequate ventilation conditions in the mine instead of main mine fans, which are commonly utilized in coal mines. Large air volumes in underground stone mines, poor ventilation practices, and low operating budgets for mine ventilation potentially increase mine workers’ risk for dust, silica, and diesel particulate matter (DPM) emissions exposure. To help improve mine ventilation practices, the optimal auxiliary fan location for maximum airflow production from a ventilated intersection was determined using a combination of field measurements and computational fluid dynamics (CFD) modeling. In this study, conducted by researchers at the National Institute for Occupational Safety and Health (NIOSH), airflow quantity and fan data were collected at a partner mine to be applied as CFD model input parameters and comparison data for model validation. A six-foot diameter auxiliary propeller fan was introduced into the validated CFD model at three locations at a mine entry intersection with established ventilation flow perpendicular to the fan direction. Placing the fan on the opposite side of the intersection from the target active face area produced the highest ventilation flow rates at the downstream locations tested and produced the lowest amount of air re-circulation. The findings show that optimizing the placement of an auxiliary fan may increase the net effective ventilation flow rate by 70,000 cfm and reduce recirculation by 26%, which maximizes the potential effectiveness of large-opening stone mine ventilation systems and decreases mine worker exposures to airborne contaminants.

Mar 2, 2022

By J. A. Brierley, Arpad E. Torma, Victor C. Storhok, C. L. Brierley, Batric Pesic

Chemical and electrochemical studies were performed during bioleaching of cobaltite concentrate with Thiobacillus ferrooxidans. The two principal minerals present in the concentrate were pyrite and cobaltite (CoAsS). During chemical studies, the effect of pH on dissolution rates was examined under uncontrolled and pH-controlled conditions. It was found that in the pH range 1.5-3.0 there was no pH effect if the initial pH was not controlled (maintained). When the initial pH was controlled, the leaching of Co, As, and Fe depended strongly on pH. Electrochemical studies were performed by using cyclic voltammetry and constant potential techniques. A sequential reaction mechanism was proposed for dissolution of cobaltite.

Jan 1, 1993