Search Documents

By Juan P. Camus, Sergio G. Jarpa

INTRODUCTION Chuquicamata mine is a large copper open pit located in the north of Chile. It has been in production for more than 80 years and now is in the later stages of its life with declining grades and increasing haul distances. As any old mine with long established organizations and procedures, it has faced one of the most difficult managerial problems: to conduct changes. Since 1994, the new management team has been devoted to a modernization pro- gram focused mainly in restructuring business operations. downsizing the labor force and introducing a mine planning pro- cess consistent with the company's goal. The explicit identification of the latter issue has been made because of the management’s conviction about the importance of it in the profitability of the business. The mine planning process at Chuquicamata mine has evolved from an old manual technique towards a modern computarized system, however the fundamental aspects and the procedures involved in this process have been the same. For in- stance, the cutoff grades policy has not changed during the last said 20 years, regardless of the changes to grade distribution, commodity prices, plant capacities, etc. To review and rethink this process, the strategy was to work with a small group of inside engineers and the management in order to interact with several mining consulting firms. The idea was to open a discussion about the fundamental principles used in the mine planning activities and, at the same time, to explore new ideas to improve the operating practices that have been followed for a long time. Thus, the goal of this paper is to present the mine planning approach that was the result of this work and the improvements that were obtained. THE CHUQUICAMATA MINE The Chuquicamata division is one of the five operations of Codelco and is currently devoted to operating the Chuquicamata mine; a copper open pit, concentrator, smelting and refining complex. It also operates Mina Sur which consists of an open pit mine, a leaching-solvent extraction and electrowinning process. There is also a dump leaching and a Sx-Ew plant for treating the low grade suifide ore (under the cutoff grade) from the Chuquicamata mine. Prior to reviewing the mine planning process, capacities for the Chuquicamata sulfide line were 640 000 tpd of run of mine material, 160 000 tpd of ore and 4 200 tpd of concentrate. This meant a total annual movement of around 230 Mt in the mine and a treatment of 57 Mt in the concentrator with a stripping ratio of approximately 3: 1. The old exploitation strategy consisted of an "open scheme", which means that all benches must have a berm with enough space to allow the traffic of large haulage trucks. This fact implied working with a great flexibility, but the consequences were flat slope angles. One of the reasons for using this operating practice in short term planning was that the grade consistency from the pit has always been a controversial variable. Schedules were designed to meet grade targets accurately and they were modified immediately when deviations become apparent. This reality led to working with a great deal of independent pushbacks and it required flexibility in the traffic system. The cutoff grade policy has been the same for a long time and the figure was 0.5 %CUT either for sulfide or oxide ore. This was the reason why a balance was produced between the mine and the concentrator. The mine is operated principally with benches of 26 m but in the upper part of the pit there are benches of 24 and 30 m. The main production equipment is shovels of 28 and 34 yd3 along with trucks of 200 and 240 st. Regarding the crushing facilities, there are two main systems located inside the pit and an old one in the periphery, close to a stockpile and near the concentrator. In the north part of the pit there is a crusher for waste material and in the north-east area is located the ore crusher facility. Both restrict a significant area of the pit and the mine sequence is considering to move the ore crusher again to the south-east sector where it used to be located. Relating to the waste crusher, the idea is to move it up to a bench near the surface in order to use the same conveyor belt and, at the same time, liberate an important sector. THE MINE PLANNING PROCESS The objective of the mine planning process is to develop a mine plan for the life of the deposit, in harmony and consistent with the company's goal. It includes the origin and destiny of tonnages and grades from the mine(s), along with the necessary resources to carry out this plan such as: fleet requirement, consumable goods, manpower, etc. From the financial point of view, it means to establish the cash flow for each time period of the mine life. That is. the revenue, capital investment and operating cost associated with each period of the plan. The fundamental principles involved in the mine planning pro- cess have been a controversial issue for a long time. One of the reasons for these divergent views could be produced by the difficulty of modeling a complete extraction policy for a geological re- source. This particular problem has to deal with several decision variables that are time dependent. So far, there is no mathematical formulation for managing such a problem, and the approach to solve it is based on a circular analysis combined with certain heuristic tools. So, a global model rather than a formula, requires a clear understanding of mine operations as well as economic theory and its application to a non-renewable resource. In order to manage this complex problem, the mine planning process can be conveniently split off in three stages which are conceptual, feasibility and operational planning. The characteristics of each stage are basically the timeliness in which they are developed and the kind and number of variables involved. Thus, conceptual planning is devoted to the definition of key variables like: the size of the operation, mining method, extraction se-

Jan 1, 1996

By Richard Emberley, Timothy Shaw, José L. Torero, Jurij Karlovsek, Timothy Gibson

"Tunnel closures are highly undesirable and the lengthiest are generally attributed to structural failures (e.g. Mont Blanc). Although historical data shows structural failures are closely linked to fire, design parameters for tunnel safety are not well defined. Current research has focused on defining the fire heat release rate and temperature, but these parameters cannot be easily used to determined structural performance. The energy transferred to the structure, the heat flux, is required but current literature lacks these values. Full scale experiments were undertaken on passenger vehicles resulting in heat fluxes between 20-70kW/m2. Analysis shows a vehicle fire’s duration is closely linked to its mass. Further analysis shows small vehicle fires can be scaled as a function of the tunnel diameter and the characteristic height of the desired vehicle. The present work provides engineers an appropriate design methodology to undertake informed thermal-structural analysis to minimize the risk of tunnel structural failure.INTRODUCTION Quantifying the effects of a tunnel fire depends on many factors such as the type of occupants, their vehicles and spacing, ventilation conditions and the geometric shape of the tunnel (Ingason and Lonnermark 2011). For design engineers investigating the thermal-structural performance of a tunnel, these factors are typically converted into spatial and temporal temperature distributions (Usmani et al. 2001) using various design curves such as those of ISO834-1, Hydrocarbon, Rijkswaterstaat (RWS) or RABT-ZTV (Promat 2013). However, to define a temperature profile through a structural element these curves require a heat transfer model that incorporates an appropriate boundary condition. The appropriate boundary condition is the net heat flux which is the result of a complex energy balance. For use in heat transfer calculations the net heat flux must account for the tunnel geometry as well as thermal properties of a given structural element and all other surfaces and mediums affecting the transfer of heat (Torero 2014)."

Jan 1, 2016

By K. A. Foo

Minproc Resources Inc. is developing a tailings retreatment project in Bolivia at the Colquiri zinc-tin-silver mine, in the Bolivian Andes. Mining at Colquiri has been continuous since 1940 and COMIBOL, the Bolivian state mining company, has owned and operated the underground mine since 1964. There are 10 million tonnes of tailings at Colquiri containing 0.51% Sn, 4.21% Zn and 50 g/t Ag. Minproc plans to mine and concentrate the tailings at 1.15 million tonnes per year to produce feed for pyrometallurgical upgrading. The tailings are moderately complex, with cassiterite grain size ranging from 200 to 5 pm. The marmatite (ZnFeS) in the tailings is relatively easily recovered, with zinc recovery of 80% to a 40%-45% Zn concentrate. The major problem with the zinc metallurgy is that the marmatite is complexed with iron, which results in iron contents of 14%-17% Fe in concentrate. This makes the product very difficult to sell because of the low Zn:Fe ratio. Most zinc smelters require a Zn:Fe ratio of 6:1 or 7:1, whereas this concentrate has a 3:1 ratio. Concentrate sale terms are therefore unfavorable, and the high cost of transportation from Bolivia to the smelters is an additional burden.

Jan 1, 1992

By R. L. Miller

"Miners worldwide use a tremendous amount of energy in producing finished minerals for the end user market. In accomplishing this goal, they incur energy costs that can range from 20% to 30% of the total cost of production, so there is fertile ground for cost savings. To unlock this huge value in cost reduction, energy analysis is the key and is broken into several segments: 1. Fuel analysis for power generation 2. Energy supply & demand 3. Opportunity cost for lack of power 4. Backup power 5. Power contracts 6. Energy efficiency 7. Renewable energy 8. Continuous energy management FUEL ANALYSIS FOR POWER GENERATION What is the first thing we evaluate when looking at power supply alternatives for the mining industry’s large power requirements? Is it 1) site, 2) engineering, procurement, and construction companies, 3) independent power producers, 4) turbine vendors, 5) grid connections, or 6) fuel supply, logistics, and infrastructure? In evaluations of power supply alternatives for mining companies with special emphasis in developing countries, there is one over-riding conclusion: reliable fuel supply drives the energy generation economic engine. Evaluating several different fuels including liquefied natural gas (LNG), natural gas, diesel, heavy fuel oil, and liquefied petroleum gases (LPG) among others, the best project outcomes are those where fuel supply, pricing, logistics, and infrastructure are given an extensive amount of time during the analysis stage. In an assessment of the twenty-year costs of generating power from multiple fuels, each fuel’s costs were placed into three separate net present value (NPV) buckets of: 1) capital, 2) operating and maintenance, and 3) fuel. Within a range of 65% to 85% for all fuels, fuel cost was the largest component of the NPV of the life cycle power generation costs. So if 65% to 85% of your life cycle power generation cost is one item, shouldn’t miners spend a corresponding amount of time in the analysis stage fully understanding this key determinant for a successful power project? In developing countries where power generation infrastructure may not exist or does not exist at the same level as is found in North America and Europe, fuel analysis becomes even more important. One of the key questions for fuel importation in developing countries is the draft at existing ports to allow larger vessels to dock at the jetty. Can larger ocean-going tankers dock at the port for off-loading, or is the port’s draft too shallow, thus forcing a Single Point Mooring (SPM) system or Conventional Buoy Mooring (CBM) system to be constructed at substantial capital expense? Once fuel can be imported, sufficient onshore storage capacity should exist, or must be built to off-load the entire fuel cargo from the larger ships. Additionally, the throughput capacity of the pipeline from SPM/CBM must allow a rapid unloading of the fuel from ship to shore to eliminate steep demurrage costs for the project."

Jan 1, 2017

By George D. Lessner

I'm sure that everyone at this meeting is aware of the current problems facing the U.S. metals mining industry. Prices are depressed and expected to remain depressed for quite some time. On the other hand, industrial minerals, including talc, are doing quite well. The profitability of industrial minerals has sparked considerable interest on the part of many companies in expanding into industrial minerals. Our company is one of those actively seeking to expand its position in industrial minerals. It is appropriate that the A.I.M.E. asked me to speak to you regarding entry into the talc business. So how do you get into the talc business? Earlier speakers have explained how to locate, mine, process, and market talc, so you have the "how ton.

Jan 1, 1984

By Milton H. Ward

The percentage of exploration dollars flowing out of the industrialized countries continues at an all-time high, and this shift in risk money is justified (Samuels, 1990; Bosson, 1977). Clearly, the odds of discovery are greatly enhanced if exploration is pursued in an untrampled and geologically more prospective environment. Unfortunately, such major unexplored areas of the developed world are shrinking rapidly, not just because the lands have already been tested, but primarily because they have been withdrawn from exploration. Experience, however, has shown that foreign investment is not without risks. These include problems that result from working in isolated areas, a lack of infrastructure, untrained workers and an absence of a solid geological data base. While the likelihood of once-feared expropriation is now low, mining enterprises still must take precautions to gain the support of their constituencies, including a variety of governments (local, provincial and central), workers, environmentalists, cultural organizations and local landowners. Is foreign exploration worth the risk? In most cases, Yes! But maintaining tenure and long-term success in a less developed country is only likely with good planning and the use of appropriate safeguards. These include measures such as buying country-risk insurance, building multinational relationships, forming joint investments, developing a broad customer base and seeking local investors in the company (Cobbe, 1979). The primary theme of this lecture is: How a company handles its constituency is critical to long-term tenure in a foreign country. Ideally, a multinational mining company would be so effective in dealing with the local people and managing its relationship with the host government that it would become a preferred employer, preferred over its competitors and over local companies. Historical overview Our earliest ancestors lived in Africa three to four million years ago. The Paleolithic or Old Stone Age, about 500,000 years ago, marked the beginning of mining in its earliest form (Gregory, 1980; Wolf, 1984). Various types of rocks and stones were used for tools and weapons, with flint being the preferred resource for implements. Initially, these materials were collected as stones (eoliths) lying on the surface. Then they came from excavations of flint in limestone beds that were exposed in river banks or naturally occurring excavations. Later, more formal mining developed. No doubt tribes of the Old Stone Age experienced conflict over rights to eoliths, food and land. The question of who owns the land and has rights to its contents and what is fair value for extraction is still the subject of intense debate and, occasionally, open conflict. As time passed, the search for useful minerals required migration from one area to another. Later, voyages from Europe to the New World and travels to other remote regions were funded and supported by absentee investors, kings and such (Rogers, 1976). The primary objective of such funding was to obtain gold, silver, food stuffs and other commodities that could be collected from the new countries. This is still the objective of foreign investment.

Jan 1, 1994

By M. S. Safarzadeh

Over the last fifty years, the treatment of enargite concentrates has not received much attention, primarily because of the availability of other clean concentrates suitable for processing with existing smelting and/or leaching technologies. As traditional copper ores have become scarcer, copper-arsenic ore deposits have garnered more interest. Arsenic release is a significant concern during the treatment of enargite concentrates by pyro or hydrometallurgical methods. Enargite is also very refractive in standard leaching procedures. Thus, economical treatment options for enargite concentrates are needed. Preliminary experiments have shown that the acid bake-leach process could be adapted and used for the treatment of enargite concentrates. In this study, low-temperature (100-400º C) sulfuric acid baking of an enargite concentrate followed by water leaching has been evaluated. The results indicate the thermal transformation of enargite to copper sulfate happens during sulfuric acid baking, with most of the arsenic being released from the concentrate into the gas phase when baking at 400º C. The condition for maximum copper extraction (~100%) from the concentrate was found to be 400º C, a sulfuric acid concentration of 0.5 mL/g and two hours baking time. Part of the arsenic was captured in the form of arsenopyrite (FeAsS). X-ray diffraction (XRD) analysis proved the presence of some arsenic in the form of claudetite (As2O3) in the baked concentrate. Acid baking of pure enargite behaved in a similar fashion.

Nov 1, 2011

By Ben Blaschuk

The Bagdad solvent extraction plant was commissioned in 1969 and was the second solvent extraction-electrowinning (SX-EW) operation to be built following the Ranchers Bluebird SX-EW plant near Miami, AZ. The current operation still resembles its original form, with four independent sections that run in parallel with each consisting of many long and narrow settlers. Through its 40-year history, the Bagdad SX circuit has experienced a range of pregnant leach solution flows and grades. The unique design of the Bagdad circuit has allowed for numerous configuration changes to accommodate the changing operational conditions, while maintaining an extraction recognized in the industry as excellent.

Jan 1, 2011

By S. K. Jena, S. Singh, B. Das, N. Dhawan, P. K. Misra, D. S. Rao

"Iron as an impurity in pyrophyllite ore affects pottery, ceramics and tile quality. We carried out the characterization of a pyrophyllite ore sample using optical microscopy, scanning electron microscopy, X-ray diffraction, Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA) and wet chemical analysis. The study revealed the presence of 2.15% iron oxide (Fe2O3 ) along with silica and alumina as the major components, which constituted around 90% of the total sample. We carried out the removal of iron from the pyrophyllite using magnetic separation and acid leaching and found that wet high-intensity magnetic separation (WHIMS) could remove 28% of iron values while oxalic acid leaching could remove up to 99.3%. The leaching kinetics of iron removal and the effects of pulp density, acid concentration, leaching time and temperature were also investigated. The optimum conditions for leaching were found to be leaching time of 60 minutes, temperature of 90°C, pulp density of 5%, oxalic acid concentration of 0.3 M, and particle size below 100 microns. Iron dissolution from the pyrophyllite sample can be best described by the diffusion of ions through the product layer of constant-size spherical particles. The breakdown of the pyrophyllite structure was evident from the FTIR and TGA studies. The activation energy of the leaching process over the temperature range was calculated to be 43.47 kJ/mol. IntroductionPyrophyllite is a naturally occurring phyllosilicate mineral composed of aluminum silicate hydroxide [Al2Si4O10(OH)2] as the major component and often associated with other minerals such as kaolinite, mica, quartz, rutile and epidote. It occurs in fine-grained sericite schist that is quarried as pyrophyllite (Pandit et al., 2008). In India, pyrophyllite occurs mainly in Madhya Pradesh state, Uttar Pradesh state and the Keonjhar district of Odisha state (Harpavat, 1995). Pure pyrophyllite is a highly desirable material for various applications due to its unique properties. It exhibits high refractive behavior, low thermalelectrical conductivity, low expansion coefficient, low hot-load deformation, low bulk density and high corrosion resistance to molten metal and basic slag (Rieger, 1997). It is used in the ceramics, refractory, foundry, electrical-insulation, sanitary-ware, glassmaking, pesticide and rubber fields. Compared with clay, it has lower thermal conductivity and coefficient of expansion, making it more suitable for refractory applications (Harben, 2002; The Minerals Yearbook, 2011)."

Jan 1, 2015

By V. R. Degner

The minerals industry trend toward very flotation machines, exceeding 10 m3, began in the late 1960's and responds to the continuing desire to achieve better plant economics through improved plant floor-space utilization, power requirements, and operational /maintenance manpower heeds. In general, as process design tonnage increases, the benefits of the larger flotation machine becomes more evident. The development of the larger flotation machine can be distingushed from earlier, smaller, machines in demanding a rational "scale-up" procedure to guide the basic design, thereby producing a machine prototype capable of satisfactory-operational evaluation at minimum cost. Proven flotation machine "hydrodynamic" scale-up consideration, successfully applied in the development of both the WEMCO No. 164 (28.3 m3) and No. 190 (42.5 m3) machine will be reviewed, and the resulting economic benefits of large flotation machines in high tonnage applications will be summarized.

Jan 1, 1985

By B. G. White

Traditional interpretations of vein ore deposits in the Coeur d' Alene Mining District, such as the view that these deposits formed in a transcurrent tectonic regime during the Precambrian, are being supplanted by the view that the deposits (1) formed in low-grade metamorphic shear zones similar to those that host an important type of gold deposit, (2) display features, such as wall rock carbonate zoning and vein zoning, that are common to ore deposits elsewhere, and (3) are probably Mesozoic and possibly related to emplacement of the Idaho batholith. In recent years, new interpretations have led to major ore discoveries that are likely to extend the life of the district for decades.

Jan 1, 1998

By Dale K. Nash

The authors have developed a com¬puter-assisted critical path planning and scheduling model to help reduce time required to move longwall mining units. The model includes time constraints and limited resource constraints, such as manpower, machinery, supplies, work space, and transportation routes. Outstanding results were achieved on the first move to which the computer-model pas applied; e.g., downtime due to the move was cut by 50%. The model and the schedules developed using it provide an excellent blueprint for future moves and have led to significant savings in time and costs for Emery Mining Corporation, Huntington, Utah.

Jan 1, 1983

By Kefton H. Teague

Olivine was first described and named by Warner in 1790. It is an olive green to greenish gray colored magnesium-iron silicate containing a mixture, in solid solution, of fosterite (Mg2SiO4) and fayalite (Fe2SiO4). Ratios between fosterite and fayalite in olivine are somewhat variable, but in general olivine contains at least 85% fosterite. Specific gravity is variable also, depending on the ratios of fosterite to fayalite. As a rule it is in the 3.2 - 3.4 range. All commercial olivine is obtained from the rock dunite, the most basic member of the peridotite group. Dunites, in addition to being composed primarily of olivine, generally contain assessory pyroxenes and spinels (chromite and magnetite). Dunites', when altered by hydrothermal solutions or metamorphism, often contain alteration minerals such as talc, serpentine, chlorite, vermiculite and amphiboles. In the 1930's and 40's considerable research was conducted on olivine for use as a refractory, plant food raw material, magnesium source for metal, and a source for magnesium chemicals. This research met with only limited success.

Jan 1, 1977

By David Harrison

Exxon Minerals Company uses geostatistical techniques for ore resource evaluation of its mineral projects. These techniques provide the most reliable estimates of recoverable tonnage and grade and uniform and realistic confidence limits. A schema has been developed which categorizes the company's successive evaluation phases. Clear separation is intended between geostatistical estimates and other factors in project evaluation such as mining, metallurgy, and economics. Company management seeks consistent and reliable estimates for investment decision-making and to meet growing demands for disclosure of mineral assets.

Jan 1, 1983

By Wang Xuewen, Bao Qingbao, Xie Jiacheng, Yan Zewen

This study puts forward a virtual memory cutting method based on the prediction of AFC shape. The integrated key technologies include the generation of virtual teaching cutting curve, the height adjustment strategy of front and rear drum, cutting height adjustment strategy, the reciprocating cycle of cutting technology and so on. Through the two algorithms, SVM and ELM, the form of the next working cycle can be obtained by rolling prediction using the form information of AFC in the first several circulations. Based on the obtained dynamic fluctuation of the form in the vertical and horizontal working faces, the position and cutting information of the shearer during its operation can be controlled and predicted in advance, the memory cutting template can be adjusted and modified in time. Employing this method, the more stable, accurate and timely memory cutting of the shearer under the uneven coal seam could be realized.

Aug 16, 2021

By Arpad E. Torma

The electrochemical behavior of a zinc sulfide concentrate during the microbiological leaching was investigated using ZnS-carbon paste electrodes and a cyclic voltametric technique. The effects of Zn2 [ ] , Fe2+, Fe3+ and Cu2+ on the cathodic and anodic currents associated with zinc sulfide leaching in presence and absence of microorganisms, were assessed. The semiconductor nature of zinc sulfide was discussed in terms of ability of microorganisms to obtain their metabolic energy (through removal of electrons) from this high energy gap substrate. The intermediate electrochemical reactions involved in the ZnS leaching were described.

Jan 1, 1989

By Yi Luo

In a shearer longwall mining operation, the longwall bits are responsible for breaking into and chip-ping the broken coal blocks away from the coal face. However, underground observations have found that a large number of longwall bits are always working under various degrees of wear. Reduction of the bit wear could be realized by using better designed longwall bits and properly selected shearer operating parameters. A computer program has been developed to simulate the performance of the longwall bits. The shape of the bit head, the installation of the bits on the drum and the operation parameters are the information required by the program. Through the simulations, the main factors affecting the bit wearing process are identified. Suggestions are also made for improving the design of the longwall bits.

Jan 1, 1996

By C. B. Manula

The Crushed Stone Industry plays an important role in Pennsylvania's mineral economy. During 1965, the total production of crushed and broken stone in the United States reached 780 million tons from which 57 million tons were produced in Pennsylvania (Mineral Industries Surveys, 1966). It is further significant that Pennsylvania is the nation's leading crushed stone producer. Future trends in stone production will quite likely parallel those in the construction industry. Stone and stone products are finding greater and more varied uses each year. Continued record expenditures for structures such as dams, highways and buildings are the prime reasons for this accelerated growth in demand. Completion of the interstate road system and the maintenance of Pennsylvania's already expanded highway system form the essentials for this expanding market.

Jan 1, 1968

By A. E. Foscolos

British Petroleum (BP, 2005), indicates that world reserves for oil to be 1198 billion barrels, for natural gas the equivalent of 1156 billion barrels of oil and for coal the equivalent of 3219 billion barrels of oil. If we take into consideration the mean aver-age annual increase in demand of the last three years for oil, 2.6%, for natural gas, 3.9%, and for coal, 6.6%, then their respective reserves? lifespan are calculated to be 27, 34 and 38 years. Without taking into account their annual increase in demand, lifespan increases to 38, 67 and 161 years respectively. Since zero increase or perpetual increase in energy demands on finite resources is unrealistic the selection of the most suitable energy commodity for power generation rests upon the law of supply and demand of each commodity. This defines its price hence its selection for the production of cheap electricity. When the ratio of supply to demand is less than one, peak production is achieved. Any further increase in demand results in price increase to quench its demand. The Association for Oil and Gas Peak (ASPO) has calculated that when oil demand exceeds 84 million barrels/day, Peak Oil Production will be attained thus prices will start to increase in order to even demand with supply. Correspondingly, Gas Peak Production is expected to take place when demand exceeds 9.1 or 10.2 billion cubic meters/day. Peak Oil production has been calculated to take place in the current year, 2006, while Gas Peak production is estimated to take place between 2020 and 2025 provided that gas will not cover the energy deficit created from the lack of oil otherwise Gas Peak production could arrive as early as 2010. The use of coal for power generation is considered a better alternative than oil and gas if new combustion technologies with an energy efficiency of 43%, Germany, and 47%, Denmark, are adopted. These not only extend the lifespan of coal reserves but reduce also CO2 emissions by 25% and 31%, respectively. In the very near future CO2 sequestration and fixation in deep geological strata will eliminate its emissions thus rendering the use of coal the cheapest feedstock for power generation.

Jan 1, 2006

By Erik Westman, Brandon Stables, Benjamin Mirabile

"Standing support is often used in conjunction with underground retreat mining. Knowledge of the load-displacement behavior of standing support and loading induced by the mine opening is critical to proper support selection. The NIOSH STOP database contains load-displacement laboratory test data for most commonly used standing supports. Hydraulic load cells currently used to measure in-situ loading of standing supports have exhibited leakage under load, producing irregularities within the dataset. An improved hydraulic load cell eliminates leakage and produces more consistent data.INTRODUCTIONA hydraulic load cell, more commonly known as a flat jack or JackPack, is a device installed to determine the loading characteristics of the roof-to-floor supports. These standing or roof-to-floor supports include, but are not limited to pumpable cribs, cans, wooden cribs (4-point, 9-point, etc.), metal props, wood timbers, concrete donut cribs, and other variations of these standing supports.Flat jack devices have been used previously to determine the loading of such roof to floor supports. The most commonly used load cell for standing supports is based on a design intended for pre-stressing standing supports, not load measurement. Preloading helps to keep the supports, such as timbers props and cribs, in place during the dynamic loading associated with blasting (Barczak and Tadolini, 2004).Flat Jacks are manufactured in various shapes and sizes depending on the application; common shapes are square and round that are 25.4 mm (1.0 inch) thick when collapsed, as shown in Figure 1. These load cells are produced in South Africa and can be formed into several different shapes depending on the application (Barczak, 2003). The sheet metal that makes up the bladder is comprised of 19-gauge or 1.11 mm (0.04 inch) thickness; the top and bottom pieces of sheet metal are resistance-seam welded around the perimeter. There are two different ports installed on one of the bladder skin corners of the flat jacks; these ports allow fluid to fill the unit, and the other port has a relief valve. The fill port is comprised of a check valve. The pressure relief valve is located in the second port; preset to 1,724 kPa (250 psi), the pressure relief valve keeps the load cell from bursting. Bursting of these load cells typically causes a small tear in the metal skin allowing the fluid to leak out without a large catastrophic failure.The effective inflation range of these load cells is between 25.4 mm (1.0 inch) to 254.0 mm (10.0 inches) thick. Different types of fluids can inflate these load cells but the most common and easily accessible fluid for testing applications is water. Water pressure from the mine supply line can inflate these load cells to the desired load. Depending on the pre-stressing requirements, a pneumatic powered pump, hydraulic pump, or hand pump may be required to inflate the load cells."

Jan 1, 2019