Search Documents

By S. Shankar

The phenomenon of re-entrainment is seen in many environments, such as sand dune formation, soil erosion, fugitive dust emission, spread of radio-nuclides from accidents involving nuclear weapons, etc. A thorough review of existing literature reveals that work on re-entrainment of dust in mine atmospheres is scant. The present study was undertaken as a part of on-going research in the Respirable Dust Center on the prediction of ambient dust concentrations in mine atmospheres (Ramani, 1983) to identify the contribution of dust re-entrainment to the spatial and temporal concentration in mine airways and included wind tunnel and in-mine studies. A set of seven experiments was performed in the Lake Lynn Laboratory Mine of the U.S. Bureau of Mines under controlled conditions. Two types of source coal dust, anthracite and bituminous, were subjected to airflow with a range of air velocities and walking by two different walkers. Six sets of instruments were used along the test section for sampling the airborne particles. The average air velocity just above the coal dust bed varied between 2.1 to 3.2 m/s. Due to re-entrainment as a result of the airflow conditions, the average respirable dust concentration in the center of the mine airway increased to 0.09 mg/m3 (standard deviation = 0.03 mg/m3) from an initial value of 0.02 mg/m3. The concentration of all (i.e., total) airborne dust increased to 0.17 mg/m' (standard deviation = 0.10 mg/m') from an initial value of 0.02 mg/m'. The action of personnel walking, however, caused higher amounts of re-entrainment. Average concentration of respirable and total dust at the center of the mine airway increased to values of 0.28 mg/m' (standard deviation = 0.12 mg/m3) and 1.53 mg/m3 (standard deviation = 1.0 mg/m3), from initial values of 0.03 mg/m3 and 0.05 mg/m3, respectively. It was observed that the dust concentrations were much higher near the floor, immediately at the end of the coal dust bed. Depending on the level of activity and the amount of dust deposited in mine airways, re-entrainment may become an important source of airborne dust away from the point of actual mining.

Jan 1, 1994

By H. D. Dahl

In January, 1969, the Central Research Division of Continental Oil Company initiated a research program on roof control. The purpose of the research was to improve roof stability. Toward this end, it was necessary to determine which of the many geological and geometrical variables have a significant effect on roof stability. The isolation of these significant variables would allow research effort to be concentrated where it would be most effective in improving roof control. The research effort was directed toward two major objectives. One was to de-fine the geological and/or geometrical parameters that affect the severity of roof conditions in any particular area of the mine. This study was concerned with roof fall intensity. The second was to define why roof falls in Humphrey No. mine (and in northern West Virginia-south-western Pennsylvania coal mining areas) are oriented so that they occur primarily in north-south rooms or entries. This study was concerned with roof fall orientation. To provide a reference framework for further discussion, a geological description of the area is presented in Part II. In Parts III and IV, the procedures, methods, and 'results of the research applied toward the afore-mentioned major objectives are presented. Part V contains the conclusions and recommendations for-warded by this study.

Jan 1, 1971

By S. D. Michaelson

Open pits and quarries are the major sources of all "hard rock" tonnage mined today. Normally, ore is fractured from the pit face by blasting and then truck-hauled to a primary crusher where processing begins; over- burden (or waste) is generally truck-hauled from the pit to dump areas. Truck haulage of blasted ore and overburden accounts for some 25 to 50 percent of total mining costs in a typical open pit and commonly is the largest single cost factor. Obviously then, cost reduction efforts should properly focus on improving existing haulage systems and developing new breakthrough techniques for material transport. Continuous flow systems for large tonnages ordinarily will result in a lower cost than batch systems such as truck or rail haulage. Continuous flow with pipelines for liquids and slurries, or conveyors for medium to coarse dry materials (in the -8 in. range) are the accepted economic answers for bulk materials handling over reasonable distances.

Jan 1, 1968

By H. Kinilakodi

In 2008, the authors developed a methodology for identifying underground coal mines at high risk for major-hazard events. It focused on major hazard-related violations of safety standards associated with high-risk conditions. Later, using a sample of 103 mines with 2008 and 2009 data, injury measures and U.S. Mine Safety and Health Administration (MSHA) citation data were combined into a safe performance index (SPI). The SPI was used to assess the relative safety-related risk of mines, including by mine-size category. In this paper, comparisons are made of SPI-associated, normalized safety performance measures across mine-size categories, with emphasis on small-mine safety performance as compared to large and medium-sized mines. Mining Engineering, 2011, Vol. 63, No. 10, pp. 73-77. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

By Rod Heath

The Saskatchewan industry has the advantages of an ore body of a size and consistency unmatched anywhere else in the world, and large, efficient mines with production costs that compare favourably with those in other countries. On the minus side, Saskatchewan is remote from most major markets, and producers face a distribution challenge to reach the offshore markets which is the main focus of this presentation. One of the characteristics of the world potash business is that all of the major sources of production are located in the developed areas of the world, while there is no significant production in any of the highly populated developing countries. The major potash producers are located in Canada and the United States, in West Germany, France, Spain and the U.K., in Russia and East Germany, and in Israel and Jordan. There is currently no significant production in any of the countries in Asia (with the exception of Jordan where a plant is currently in the start-up phase), Africa, Latin America or Oceania, and all of these areas must, therefore, import a11 of their potash requirements from the producing countries.

Jan 1, 1985

By Raymond F. Moran

The history and development of the FMC Coke process has been reported in numerous presentations over the past 10 years (1, 2, 3, 4, 5, 6) but a short review is desirable, especially regarding the aspects that are influenced by the coal to be used. F'MC has been developing this process in pilot facilities since 1956 and in a modest sized plant in Kemmerer, Wyoming since 1960 (Figure I). This plant produces strong uniformly sized coke briquettes from a completely non-coking coal, namely Elkol, a sub-bituminous coal of the Adaville seam. Since operating commercially, over 300,000 tons have been produced, 90% of which has been used in electric phosphorus furnaces and some 10% of which went for trials in iron blast furnaces. We believe that this commercial use of non-coking coals is a unique experience in the history of coke manufacture.

Jan 1, 1975

By L. Alagha, L. Sanchez-Calderon, M. Silwamba, W. Kirk

Selenium-rich metallurgical waste, also known commercially as “crude selenium,” is a byproduct of the copper (Cu) refining process. This by-product, contains ~ 90% selenium (Se), precious metals, platinum group metals (PGMs), and other critical elements. This study investigated the leaching efficiency of Se from the sludge under alkaline conditions using different oxidizing agents to enrich PGMs and precious metals in the leach solid residue. The effectiveness of each oxidizing agent during leaching was assessed and compared. Additionally, Eh-pH diagram for Se was established under specific experimental conditions and utilized to inform process optimization. Key variables, including leaching time, temperature, and oxidant concentration, were evaluated for their impact on the efficiency and the selectivity of the oxidative alkaline leaching process.

Feb 1, 2025

By H. Zhao, R. Liao, W. Qin

Theoretically, controlling redox potential to a relatively low value and inhibiting jarosite formation on the chalcopyrite surface would be an effective strategy to accelerate the bioleaching of chalcopyrite. In this work, using limonite as seed crystals, the effects of the goethite precipitation process on the bioleaching of chalcopyrite were studied for the first time. The bioleaching results showed that the addition of limonite controlled the redox potential in an appropriate range and promoted chalcopyrite dissolution through the removal of ferric (Fe3+) ions. X-ray diffraction and scanning electron microscope analyses indicate that limonite significantly induced the goethite precipitation process and inhibited the production of jarosite. We conclude that promoting the goethite precipitation process with limonite is an effective strategy in accelerating the bioleaching process of chalcopyrite.

By X. Cai, L. Jiang, G. Fu

A process for recovering manganese from low-grade manganese oxide ore through a reduction acidolysis-selective leaching method is investigated. Two types of biomass, sawdust and straw, were used as reductants. Reduction acidolysis, using concentrated sulfuric acid, was used to disrupt the structure of the biomass, allowing the biomass to be hydrolyzed into monosaccharides. Analysis by X-ray diffraction revealed that Mn2O3 was reduced to MnSO4. Then, in the selective leaching process, iron was removed through the formation of goethite. The optimized experimental parameters are as follows: reductant to ore mass ratio of 0.4, sulfuric acid to ore mass ratio of 0.9, water to ore ratio of 0.5, aging time of 18 h, leaching temperature of 95 °C, leaching time of 90 min, and solution pH of 2.5 to 2.8. Under these conditions and using sawdust as the reductant, the manganese leaching efficiency and iron removal efficiency were 91.8 and 99.2 percent, respectively.

By Lee A. Goetz

Cost control is a lot like motherhood - everyone proclaims its need and its worthiness, but is it really appreciated and used to successfully complete a project on time and within budget? Good Cost Control is a yardstick - requiring fixed definition but this does not mean rigidity for the project. It provides the means for telling: 1. Where you are going 2. When you will complete and 3. What it will finally cost. Cost Control does not fix the price of dreams nor the cost of projects loosely defined. It does not control costs in itself but provides the tools whereby engineering decisions can be made which will ultimately affect the project cost It does not even guarantee that a project will be completed within the original funds - but only, if this reflects management desires.

Jan 1, 1970

By Xinyang Wang

It is believed that sulfur and volatile matter con-tents in coals are the main intrinsic properties to cause the self-heating of coal. Their oxidation at lower temperatures than that of fixed carbon to initiate coal's self-heating should be quantified. This study is aimed to improve the previous mathematical model developed by the authors for studying the coal's propensity for spontaneous combustion. It enhances the model's ability to consider the effects of sulfur, volatile matter and moisture contents in the coal three important factors affecting the coal's self-heating process. Sulfur exists in coal primarily in the form of pyrite which will be oxidized rapidly under suitable conditions. Volatile matters, higher in low rank coals, are more easily to be oxidized. Heat of water condensation provides initial energy for low temperature oxidation. Heat release rates for pyrite oxidation and moisture condensation are built in the model. Finally, the simulation results in terms of time versus temperature on pyrite oxidation and moisture condensation are validated with the adiabatic testing data respectively.

Jan 1, 2013

By Michael Day, Paul Kos, Scott Brinton

A hydrogeologic characterization and impact analysis was performed for a proposed quarry at the Hitch Rack Ranch located in the Little Turkey Creek watershed southwest of Colorado Springs, Colorado. Continuous multiple channel tubing, nested piezometers, stream flow measurements, and mapping of known seeps were used to define the three-dimensional potentiometric distribution and areas of groundwater recharge and discharge. Water balance considerations, mass balance calculations, and potentiometric response to earth tides and barometric fluctuations confirmed that the granite fracture system in the ridge area of the proposed quarry has an extremely low bulk hydraulic conductivity resulting in minimal groundwater discharge to sustain the baseflow of Little Turkey Creek. The Little Turkey Creek valley forms the major conduit for groundwater flow exiting from the upper part of watershed underlain by granite. This conclusion has significant implications with respect to mine planning to minimize projected impacts to the hydrologic system and preserve this recharge component to downgradient Denver Basin sedimentary deposits.

By Robert W. Bruhn

State and federal regulations require that surface mine overburden be investigated in advance of mining for naturally occurring earth materials that are detrimental to animal and plant life or to uses of water. Proper identification of these toxic materials is necessary to permit development of environmentally sound reclamation programs. Intensified use of present laboratory methods to meet anticipated testing demands would be both costly and time consuming. This paper discusses the desirability of and general requirements for a geophysical system capable of locating toxic zones in the overburden of surface mineable lands of the Northern Great Plains Coal Province. The paper (1) identifies the types and character of naturally occurring overburden substances that must be investigated in advance of mining, (2) discusses the economic justification for development of a geophysical system to replace or to complement conventional laboratory test methods, and (3) discusses the potential applicability of downhole geophysical methods to overburden analysis.

Jan 1, 1981

By Felicia F. Peng

An economic analysis for evaluating coal preparation plants in the Appalachian Region is presented. A complete coal preparation plant which includes multi-streams and/or multi-stages coal cleaning circuits, complete closed water circuits, environmentally acceptable refuse disposal and reclamation systems is used to determine the capital and operating costs. The plant is capable of producing metallurgical grade clean coal or deep cleaned steam grade coal for future power generating plants use. Utilizing a profit maximization as a decision criterion, an optimal yield, and optimal coal clean¬ing circuits, closed water circuits, and disposal and reclamation systems for a given coal characteristic may be selected among the process alternatives by using a process simulation-economic model of the coal preparation plant. A deterministic analysis is used to calculate the discounted-cash-flow interest rate of return (DCFIROR) and project the selling prices, and determine the Return on Investment (ROI) for the cases of 32.65% and 52.74% plant utilization with producing two cleaned products. Sensitivity analyses are performed to quantify the effect of total capital investment, operating cost, run-of-mine cost and yield on an economic criterion-ROI and selling prices. A probabilistic evaluation using the Monte Carlo simulation technique is further made to quantify the risk involved in obtaining the desired profit levels. The results of the economic analysis for a given coal preparation plant configuration and characteristics of raw coal indicates that the selling prices of producing two cleaned products are greatly affected by the change in percent of plant utilization (production schedule), yield, and run-of-mine cost, and total capital cost. The sensitivity analysis also shows that the total capital investments has a three times greater effect on required selling prices than operating costs. The risk analysis shown that the overall economics look very attractive with current coal sale prices and 52.74% plant utilization.

Jan 1, 1979

By Franziska Wolf, Rainer Ellmies, Helmut Mischo

"Mining is an important part of the economy of Namibia. In 2016, 11.1 percent of the GDP was the result of mining activities with 22 active mines (The Chamber of Mines of Namibia, 2016). Only one of them consists of an underground mining operation.The global annual production of fluorspar is approximately 5.4 to 6.3 Mt (6 to 7 million st) (U.S. Geological Survey National Minerals Information Center, 2017). Okorusu has produced on average about 45 kt/a (50,000 stpy) in recent years (U.S. Geological Survey National Minerals Information Center, 2015).The Okorusu Mine is Namibia’s only fluorspar mine. Fluorspar was mined in an openpit mine with four individual pits (A-D) since 1980. In 2014, the mine closed due to the increased stripping ratio and beneficiation problems. The mine assets were bought by Gecko Namibia. Currently, Gecko uses parts of the processing plant for beneficiation of graphite from a neighboring mine. Figure 1 shows a panoramic view with the four pits and the mine village.The intent is to develop a concept for the further underground development of the mine. There are still about 6.3 Mt (7 million st) of measured resources left in the deposit, with an average grade of 27.5 percent CaF2. This study focuses on the underground mine design. The above-ground plant and facilities are considered as remaining unchanged.For solving the task to design the mine, a site visit for data collecting was conducted. Resource estimations were calculated based on existing drill data, and consequently, block models were created. The development of the mine design included the selection of the most suitable mining method, mining technology and mine organization. Moreover, some economic considerations are pointed out, followed by a profitability assessment."

Jan 2, 2018

By Xie Longshui

INTRODUCTION The gold production is from the state-owned gold mines, the local gold mines and the by-product of metal mines. Since 1975, the small gold mines have developed in rapid strides. Currently, there are about 3000 small gold mines in China. Most of them are operated by the local, and the production is about 50% of China's gold output. In the small gold mines, the normalized mining equipments are employed at most of mines, but some mines still use such backward tunnelling and mining tools as pick, shovel and hand hammer etc.. The mining techniques have developed from the primitive to the advanced, especially the methods of open stope, shrinkage and filling have been widely used. Such new mining techniques as bolting, vibrating draw, non-electric ignition and diamond drilling etc. are also introduced in the wall gold mines. In recent years, the development of small gold mines is very fast under the guidance of new mining policy which is ' rapid and great development of large-sized mines, helping small mines to develop, and quick mining for the existing mines; and encouraging the collective and the individual to operate a mine.' GEOLOGICAL FEATURES The gold veins are dominant, which are divided into two types, ie. the mesothermal deposit with altered rock in a crushed zone and the hypothermal deposit with quartz veins. The orebody distribution is not centralized, and the size of deposit and single minable orebody is small respectively. Most of deposit dip at 30° to 50°, characterized by expansion and shrinkage, ramification and compound, thinning out and reappearance, separation and composite at the parallel veins etc.. The ore grade is variable, and the factor of grade change is above 100%. The waste zones with lean or submarginal ore usually exist in deposits. As for the gold deposits with altered rock, the ore boundary is indistinct. Most of gold deposits, particularly the gold deposits with altered rock, are intruded by the late structural rock, thus the faults and joints are developed, and the rock and ore are crushed, especially the host rock of roof wall is very crushed. It ie obvious that the conditions of both formation of deposit and mining are considerably complicated. HISTORY With a long mining history and rich experiences, the local gold sectors are small, but they play an important role in China's gold mining industry. Dated from Xia and Shang Dynasty, the gold goods was made. In the Tang Dynasty, the development of gold mining industry was very fast. A Chinese poem , written by Liu Yuxi -- one of famous poets in the Tang Dynasty, says: As sun is shining over Dengzhou land, The fog on river slowly goes away, The panning girls together meet at bay, The beauty's jewels and stamps of king are gold from river sand. This poem shows the local gold mining was flourishing at that time. In 1888, the local gold mining sectors were all the rage at the moment, and the annual output of gold was as high as 21.5 tons. Since the founding of New China, the development of local gold mining was subjected to several back- sets, but certain advances are made on the whole, especially since 1970. Round about 1970,the simple, backward and indigenous mining was dominant in the small gold mines; for instance, the hand-hammer drilling, the hand-operated winch hoisting and the hand haulage etc.were main methods of gold mining . Up until the late 1970s,great changes took place in stoping, haulage and so on. Currently, some advanced technology and large-sized equipments are adopted in the local gold mines. Generally, the local small gold mining sectors play an important role in development of China's gold mining industry, and are important and attractive sectors. PRESENT DEVELOPMENT

Jan 1, 1987

By Michael G. Zabetakis

Effective accident prevention programs utilize a broad spectrum of activities, including meaningful training programs. In practice, such programs must be directed towards specific, defined needs. These needs are considered here for three categories of employees: new, re-assigned, and experienced.

Jan 1, 1983

By S. S. Cook, S. E. Paulson

The US Bureau of Mines is conducting core leaching experiments with sulfuric acid on oxide copper ores from the Cyprus Casa Grande and Asarco/Freeport Santa Cruz deposit in Arizona to further the understanding of the leaching process in supergene copper ores as it relates to in situ mining. Leach solutions from atacamite mineralization contained 5 to 30 g/L (0.05 to 0.28 oz/gal) copper and few extraneous ions. Leachant from chrysocolla ores, with grades similar to the atacamite, contained 2 to 9 g/L (0.02 to 0.08 oz/ gal) copper and abundant extraneous ions. Quartz and K-feldspar had no impact on leach solution composition at any acid concentration up to 40 g/L - (0.39 oz/gal) while illite and sericite had minimal impact. Biotite, calcium-rich clay, and limonite have a significant impact on solution chemistry when there is abundant free acid in solution. High acid concentra¬tions increase acid consumption in ores with abundant biotite and limonite gangue. High acid concentrations can be used in ores with quartz, K feldspar, and sericite gangues without increasing acid consumption per unit of copper removed.

Jan 1, 1990

By Paula N. Wilson, W. T. Parry

Carbonaceous and metalliferous black shales occur in close proximity to Mercur-type gold deposits in the southern Oquirrh Mountains, Utah. These shale units, the Manning Canyon shale and the Long Trail shale, have undergone regional hydrothermal alteration. Hydrothermal solutions oxidized organic matter and pyrite, replaced shale by hydrothermal phyllosilicates and silica, and replaced fossils by phyllosilicates. The shales are depleted in organic carbon, calcium carbonate, alkali and alkaline earth metals, and enriched in aluminum and hydrogen. Hydrothermal veins containing illite, chlorite, pyrophyllite, kaolinite, Fe-oxides, and sulfides are present throughout the study area.The illite in veins is an ammonium illite that contains up to 2 % NH4 and is correspondingly depleted in K. Correlations among Au, As, Hg, TI, Sc, and rare earth elements indicate that hydrothermal fluids responsible for formation of ammonium illite were gold bearing. K/Ar ages of illite veins and illite-rich, clay-size separates of altered shales indicate hydrothermal activity occurred in the time range 193 to 122 Ma. Several ages from clay-size separates within the Mercur district cluster near 160 Ma. These ages are coeval with thrust faulting recognized to the north and west.

Jan 1, 1990

By Aliakbar Golshani, Behnam Eslami

"Surface settlement adjacent to sensitive structures is a challenging issue in the tunnel engineering. In this study, 3D simulation of TBM excavation has been performed with the FLAC3D code and then the results compared with real monitoring data. Sensitivity analysis was carried out for all parameters affecting the surface settlement, such as the tail void grouting pressure (Pt), the face pressure (Pf), the tunnel diameter (D), overburden (q), shield thickness (t) and the length of the shield (L). The results show that the face pressure, tail void grouting and tunnel diameter have a considerable effect on the maximum ground displacement.In this paper, the monitoring data from Mashhad Metro was used to verify the numerical simulation. Data monitoring for about 47 sections between A2 and D2 stations was selected and a multiple regression analysis was performed. Based on this analysis, an empirical relationship was obtained for the coefficient of regression relationship which confirmed the sensitivity analysis.INTRODUCTIONThe surface settlement due to tunnel excavation is a complex issue, since the surface displacement is a function of several parameters that they are related to the excavation method, soil characteristics and TBM elements. Prediction of deformation is a very important issue, especially in urban areas, since these displacements may be affected the superficial structures. In recent studies, one of the most popular empirical relationships that is used to predict the surface displacement has gussian curve that it was suggested by Peck [1, 2]. An analytical relationship was proposed by Chow that its base assume was isotropic of soil, that surface settlement can be estimated based on the tunnel geometry and the shear modulus(G) [3]. Besides these methods numerical approaches such as the Finite Element Method (FEM) and the Finite Difference Method (FDM) have been used over the last twenty years, since numerical modeling has a high capability to simulation a complex soil conditions and irregular geometry [4]. In this study, all aspects of the EPB-TBM on Mashad Metro Line 2 were modeled and the most important influences on surface displacement in urban areas were determined [1, 3]."

Jan 1, 2016