Search Documents

By A. A. Schweizer

Buckhorn ore is hydrous, argillized basaltic andesite, and is at least 60% clay composed of kaolinite and subordinate montmorillonite. Moisture content runs from 10% to 25%. The original crushing plant was a typical compression type, employing a jaw crusher, and two cone crushers. The system was plagued with constant plugging and unable to meet production plans. The three compression crushers were replaced with a Stamler Feeder Breaker followed by a Hazemag Impactor. Production plans are now exceeded. Agglomeration has progressed from an agglomeration drum to cascading conveyors, to introduction of the lime and cement into the primary crusher.

Jan 1, 1987

By M. Kuchta, S. Iverson

INTRODUCTION Underground blasting with perimeter damage control can reduce the requirement for loose rock scaling and reduce the risk of ground-fall injury. In previous work Johnson and associates (2010) from the National Institute for Occupational Safety and Health (NIOSH) developed a rock blasting perimeter damage and control design method included in the DRIFT software tool (NIOSH, 2018). This blast design software tool utilizes current methods of perimeter blasting with the added design element of a buffer row coordinated with the perimeter row to reduce perimeter damage. The coordination is in applying one of several blast damage models to calculate the damage extent for each production, buffer, and perimeter blast hole in the design. The calculated damage is then applied to the spacing between the blast holes. The basis of the buffer row design is the practical damage limit and is supported in this paper with computer models of signature blasts and full blast rounds using PFC2D (Itasca Consulting Group, Inc., 2018). Practical damage limit The practical damage radius (Rd) is not to be confused with burden. The practical damage extends toward the burden side and inward into the rock mass. For all practical purposes, the practical damage radius equals one half the burden (Hustrulid, 1999). The maximum extent of radial crack damage around a blast hole (Rcrack) and the maximum extent of radial crushing damage (Rcrush) are illustrated in Figure 1. A “practical” radius of damage (Rd) lies between the crushing limit and the cracking limit. The “practical” damage means that if the rock mass lying outside of the practical damage circle were removed, the rock remaining within the circle would easily break apart. Blast pressure and strain Work by Johnson (2010) and associates included signature blast tests in large concrete blocks. A signature blast test in concrete as exampled by strain data in Figure 2 was designed to monitor the dynamic strain at incremental distances from a single fully coupled blast hole, measure crushing and radial cracking extent by wire-sawing to expose the damage, and relate the damage to overbreak that is common in underground blasting. The initial slope or rising strain as the stress wave passes by the strain gages shows very high strain and strain rates close to the single blast hole. Since the derivative of strain versus time is strain rate, a line tangent to each of the strain curves at the maximum strain rate is drawn and the strain rates identified. The high strain rates were then plotted on a semi-log in Figure 3 to show a linear trend. The strain rate is greater than 100 s-1 within 20 cm from the blast hole for the signature blast experiment. The strain rate at the blast hole wall is projected to be 300 s-1. Figure 4 illustrates the damage in the NIOSH block exposed by a wire saw cut.

Jan 1, 2019

By Ben Roderds

The Waneta Expansion Project (WAX) is located near the existing Waneta Dam site at the confluence of the Pend d?Oreille and Columbia rivers, approximately 10 km (6.2 miles) south of Trail, BC, Canada. The WAX owners consist of a partnership between Fortis Inc., Columbia Basin Trust and the Columbia Power Corp. This design-build project was awarded to SNC-Lavalin in late 2010 and is expected to be operational in mid-2015. The WAX consists of a new 335-MW powerhouse, including two new Francis turbine units, each generating approximately 167 MW. The powerhouse is located downstream of the existing Waneta Dam, and will make use of excess water that would otherwise be spilled during the runoff season. Water will be funneled to the turbines through an intake structure and two 10.5- m (34.5-ft) diameter, concrete-lined Penstock Tunnels. A 10-km (6.2-mile) transmission line will connect the powerhouse to existing electrical grids. Redpath/FKCI Waneta Tunnelers (RFK) was subcontracted by the heavy civil contractor, the Aecon/SNC Lavalin (ASL) joint venture, to excavate the two penstock tunnels and install the cast-in-place concrete liner. RFK is a joint venture partnership between J.S. Redpath Ltd., an underground mine contractor located in North Bay, Ontario, and Frontier-Kemper Constructors ULC, a heavy civil tunneling contractor based in Nova Scotia, Canada. Since penstock tunnel excavation was planned using drill-and-blast methods with a significant grade of more than 17 percent, the combined experience of these two contractors was a perfect match.

Mar 1, 2014

By Zainab Nasrullah, MontanaFrank Agyemang, Mehran Sadat, Richard LaDouceur

Rare earth elements (REEs) are valuable for various modern technological applications, including metallurgy, machine building, radio electronics, instrument engineering, nuclear engineering, and manufacturing. The extraction and separa-tion of rare earth elements (REEs) from their complex ores is challenging due to their distinct physical and chemical properties, contributing to their market scarcity. At present, REE recovery utilizes traditional pyro- or hydrometallurgi-cal processes. The overall process in the recovery and sepa-ration of individual elements from complex REE systems suffers from high energy demands and the use of many haz-ardous chemicals that negatively impact the environment. With the growing trend toward a circular economy aim-ing to balance sustainability, efficiency, and environmental impacts, this research is focused on using deep eutectic sol-vents (DESs): a combination of a quaternary salt: Choline Chloride and five organic acids: Oxalic Acid, Urea, and Ethylene Glycol, Lactic acid and Glycerol for the selective leaching of REEs from their complex ore which is proven to be green, selective, non-toxic, biodegradable, and cheap. The effects of different DESs and leaching time on the REE leaching efficiency were determined, and the optimum DES media were found to be Oxaline and Lactic Acid at which a leaching efficiency of 25% and 15% was achieved at 80°C respectively for cerium.

Feb 1, 2025

By Greg Colzani, Emily Thompson

The 3RPORT Project, includes a 5-mile tunnel excavated by a 19-foot diameter slurry Tunnel Boring Machine below the city of Fort Wayne, IN. The Geotechnical Baseline Report (GBR) indicated vuggy to massive argillaceous dolomite within the tunnel alignment. During excavation of the first reach, the TBM encountered zones of cohesive clay and sandstone presented in full face and mixed face conditions. The occurrence of Sandstone was not a “Baselined Condition” described in the GBR for this reach of the alignment. This paper will discuss the methodology to investigate, mitigate and evaluate the DSC impacts on TBM performance.

Dec 1, 2022

By C. E. Golson

Modern concrete technology emphasizes the basic qualities required of an acceptable aggregate: it must be clean, sound, homogeneous, and of a size gradation resulting in a concrete of the desired physical qualities at a minimum cost. In the case of coarse aggregates, crushing, scrubbing, and screening will usually provide the required material, although beneficiation is often necessary in order to eliminate unsound or deleterious fractions. Beneficiation is also applicable to fine aggregates,( but the processes most often employed are washing, classification, and dewatering.

Jan 1, 1959

By Kenneth J. Edmiston

The objectives of this paper are: to review the current status of chloride leach processes for sulfide concentrates, to make an evaluation as to the applicability of chloride leaching for replacing pyrometallurgical processes and to comment on recent advances in construction materials. The paper does not delve in detail on process chemistry. Sufficient references are presented on each process to allow the interested researcher to obtain process chemistry details. GENERAL The fact that chloride oxidates can solubilize base metals from sulfide concentrates has been known since the 1880's. The work of Hoepfner in 1902 was particularly accurate for its time with regard to the chemistry of chloride solutions. Recent work has dealt with the understanding of chloride extraction thermodynamics by modelling the behavior of metal chloride complexes. In the last several years several excellent review articles and symposiums have been issued covering chloride chemistry (1 thru 6).

Jan 1, 1984

By S. Saklar, i. Bayraktar

The effect of the feed size distribution on the kinetic parameters in pyrite flotation was studied. The kinetic parameters of the particular sizes were determined as a function of whether other particle sizes were present. From the data, a relation between the pyrite flotation rate and the particle size distributions was obtained. It was shown that the flotation rate constant (k) is a function of the size modulus (dt) of the Gates-Gaudin-Schuhmann distribution, and its variation may be expressed as k = a • exp(b . d,) for either individual size fractions or composite feed. Parameters a and b are dependent on the particle size distribution of the feed. Specifically, parameter a increases linearly as the distribution becomes coarser. The above relationship was also tested under conditions in which the collector (KAX) dosage was varied from 130 to 278 g/t. It was shown that the established relation was not dependent on the collector dosage.

Jan 1, 2002

By AMIT SHARMA, BIBHUTI BHUSAN MANDAL

This paper describes the vibration transmissibility characteristics of mining vehicle seats under dynamic conditions in an opencast iron ore mine. Magnitude and frequency contents of vibration signals on the seat floor as well as on top of the seats were measured to record the change during transmission. The conventional rigid seats were found to resonate at about 4 Hz, which coincides with the resonance of the human spine. The pneumatic suspension seats also proved to be more efficient in attenuating the overall vibration energy transmitted from the vehicle chassis to the human body.

By Fathi Habashi

CRYSTALLIZATION from aqueous solution is a simple and old method for the recovery of metal values from leach solution. Practically all the methods for the recovery of aluminum from clay are based on the crystallization of an aluminum salt from the leach solution. Differences in solubilities may be used to advantage for separating two metals from the same leach solution. The classical method of Marignac (1866), which makes use of the difference in solubilities of K2TaF7 and K2NbOF5 to separate niobium from tantalum, has been used successfully in the manufacture of these metals (Fig. 10-1). The slurry containing the metal oxides is dissolved in 70 % hydrofluoric acid, diluted, and heated near boiling. A potassium salt is added in sufficient quantity to form the complex fluorides of the niobium and tantalum present. The solution is filtered and allowed to cool. At room temperature most of the tantalum salt crystallizes out while the niobium remains in solution.

Jan 1, 1970

By R. H. Ring

The Automatic Extraction System (AES) was designed and built under a U.S. Department of Energy Contract by the National Mine Service Company in cooperation with the Lee Engineering Division of Consolidation Coal Company. The Pennsylvania State University, Mining Engineering Section, was contracted as an independent auditor of the AES performance. The AES had a rotating cutter drum like a continuous mining machine; but two hydraulically powered roof supports, four roof-bolting drills, a dust scrubber, a ventilation fan and ducting in the roof supports, semi-automatic control, an extensible chain conveyor, and other innovations led to the distinction "extraction system" as opposed to "miner-bolter" or "continuous mining" machine. After design and assembly, the AES was field tested experimentally in an underground coal mine. The in-mine performance audit was preceded by a computer simulation of the potential production for a later comparison with the actual tonnage mined by the AES. This paper describes the results of an in-mine trial and assesses the production potential of the AES.

Jan 1, 1980

By Nathaniel Arbiter

After almost 60 years of application in this country froth flotation is still by far the most important process for concentrating metallic ores as well as a number of nonmetallic ores including fluorspar, phosphate rock, and potash. Its use on iron ores and coal is increasing. In the metals groups the largest plants and the greatest progress are found in copper and molybdenum mills, and the section of this paper that deals with applications will be found most pertinent to that field. During its long reign the flotation process has passed through several phases of evolution and has achieved progress in economy, efficiency, and simplicity of operation. Much of today's success in the flotation of low-grade ores can be attributed to that progress. Even more important to us than our ability to cope with today's conditions are tomorrow's problems, which we can contemplate with some prescience and confidence. Our annual production of copper, lead, zinc, and molybdenum--to mention only the most important metals occurring in the U.S. as sulphides--must be held at a high level in the face of a declining grade of ore. It is probable that the tonnage of such ores mined and processed will double in this country before the turn of the century. Not only will many of the existing flotation mills be enlarged again and again, but larger mills will be built here and abroad to meet our needs. At this moment, in fact, there are at least three proposed new foreign mills or expansions that envision 100,000 tons daily milling rate on copper ores. Table I (1) shows the trend in copper ore grades in U.S. in recent years:

Jan 1, 1970

By R. Das Gupta

Variations in the characteristics of bentonite, magnetic taconite concentrate and system water have been examined to show their effects on pelletizing. Chemical methods have been tried to alter the clay or the system water so as to obtain pellets with desired properties. Those methods include ion exchange and the use of supplemental binders (organic and inorganic).

Jan 1, 1978

By E. K. Albert

Computer oriented simulation techniques can be effective in the design and analysis of complex mining systems. In fact, a number of computer software products are available for mine systems simulation. While providing a useful tool for the investigation of mine planning problems, the availability of graphic output was limited or non-existent. Computer graphics is a natural extension of mine simulation methods and provides a more dramatic level of understanding and interface with an engineer. With today's high cost of venture development, the need for an easy to use but complete systems model which includes the major elements of mine planning with an interactive graphics interface has never been more apparent. In this paper, the underlying philosophy of design of an interactive interface to a complete surface mining simulation model is described. The basic structures of the surface mining system and the simulation model are discussed. The methods and algorithms used to implement the various subsystems are presented. Practical considerations of the design of displays and user interaction are illustrated, especially as they apply to the application of the package by a mining engineer. A simple example is provided to demonstrate the concepts embodied in the model and to show how a simulation is built from mine data.

Jan 1, 1984

By James A. Finch, Xiang Zhou, Yue Hua Tan

Methods to determine frother functions, control of bubble size and froth properties, are now widely used. Some collectors also exhibit frother functions which are less understood. Using a water-air system in a mini-mechanical flotation cell setup, this paper determines bubble size and water overflow rate for three amine collectors: one primary amine (dodecylamine, DDA) and two commercial ether amines (Flotigam® EDA and Flotigam® 2835-2L) and their combination with two common frothers, MIBC (methyl isobutyl carbinol) and PPG 425 (polypropylene glycol, molecule weight 425). Compared to the frothers, the amines were less effective in reducing bubble size, giving larger minimum size and the two commercial amines showed evidence of coalescence at low concentration. In blends, at fixed frother dosage, frother eliminated the coalescence but as amine concentration increased the amines dominated bubble size. Water overflow was a strong function of reagent type. For fixed 1-cm froth depth, PPG 425, Flotigam® 2835-2L and to a lesser extent DDA produced overflow while MIBC and Flotigam® EDA did not. In blends with frother overflow increased except with Flotigam® EDA. Mechanisms are briefly explored. The principal benefit of blending identified is the elimination of coalescence if residual concentration of the two commercial amines is below ca. 10 ppm.

By Dan Nilsson

The Luossavaara "Research Mine" is the First large, offensive effort in mining research conducted by the Swedish state. Over a 5-year period, 1981-1985, the Swedish Mining Research Foundation works in the "Research Mine" on the development of mining systems and equipment. The purpose is to bolster the competitive strength of the Swedish mining and mining equipment industry. The previosly abandoned Luossavaara mine in Kiruna, in northern Sweden, has been reopened especially For the project. Ore is mined and sold during the course of the research project. The income from the sales covers a large portion of the costs for teh research.

Jan 1, 1985

By F. Shigeyoshi

The development of pelletizing during the last ten years has continued, however, self-fluxing pellets have not been regularly and commercially produced for use in blast furnaces, except as Kobe Steel, Ltd., Japan. This paper tells about unique developments for self-fluxing pellets, and their effects when used in Kobe Steel's No. 3 blast furnace at the Nadahama Works (inner volume 1845 Nm3, hearth diameter 9.5 m)., Several phases of the pelletizing process are discussed individually, and also their relation to performance in blast furnace operation. Special emphasis is placed on proper preparation of the limestone added to the raw materials, and indurating at optimum conditions. Means of improving pellet quality by correct control of size distribution of the raw materials used in pelletizing, and indurating temperatures, are also discussed. As basicity (CaO/SiO2) of pellets increased 0. 1, coke consumption decreased 3. 8 to 4. 2 kg per ton of hot metal, when using 70% pellets in the iron burden.

Jan 1, 1969

By Malte J. M. Gurgel, Axel Preusse

The planning, construction, and monitoring of underground storage facilities is a key factor in meeting upcoming challenges as part of the energy transition from fossil fuels to renewables. Therefore, the many years of knowledge and expertise in ground control gained from coal mining are highly valuable for new mining and storage operations. For such applications, our previous work examined cavity registration, combining structure from motion and LiDAR through a case study in a former lead ore mine. Building on this, the results of this recent case study are discussed regarding the possible application in sites for nuclear waste disposal in Germany including a view on the situation in the United States. Photogrammetric methods are particularly suitable as part of long-term monitoring, which relies on both precise survey results and a large variety of detailed visualization. In order to gain a better understanding of the resulting application potential for holistic monitoring, both existing repositories sites in Germany and ones yet to be found are examined. This search and selection process for high-level nuclear waste disposal is studied in detail together with rules resulting from the (German) mining law, regulations, and other guidelines. Hereby, key requirements of photogrammetric products like oriented images, point clouds, and three-dimensional (3- D) models are identified for different case studies. The findings on accuracy and integrity of the generated models are not only of interest for future repository sites or underground pumped storage power plants, but also offers various possibilities for underground mining of coal and other commodities.

Jul 1, 2023

By Martin B. Zimmerman

It is becoming evident that traditional methods of econometric analysis are inadequate in estimating-the long-run supply of minerals. Econometrics is limited to extracting estimates from observations of the theory predicts that the least cost deposits will be exploited first.1 The estimation of parameters from past data then must lead to biased projections of the future. Mining conditions in the future will be worse than in the past and it is the impact of the future conditions on cost that we need to know. In this paper we present a methodology for dealing with this problem. We estimate a "cumulative cost" function that yields the long-run marginal cost of mining as a function of cumulative output produced over time.2 This is relatively easy to do for coal mining in the United States where exploration for new deposits is not a major factor in supply. The first step of the procedure relates cost to the rate of output and to the geological conditions of the mine. The second step combines geological information on remaining deposits with the cost function to yield the cumulative cost function. A central theme of both these steps is the interaction of economics with geology. The best deposits are selected first and in each step of the estimation allowance must be made for this fact. The problem of depletion is part of the general problem of structural change. The change through depletion in the nature of the exploitable mineral stock is only one factor that calls for an analysis sensitive to the changing circumstances of the industry. The factors impinging most heavily on the coal industry today are the strict environmental regulations legislated

Jan 1, 1977

By E. Molleman

This paper reports on testwork exploring the dissolution/reprecipitation reaction: ZnS + 2HCl ? ZnCl2 + H2S, as part of a process for the production of pure ZnS. In spheroidal form, this would constitute a premium fonn of zinc refinery roaster feed enabling the production of pure ZnO. The research focused on the influence of proton activity on dissolution of zinc concentrates from Brunswick Mining & Smelting, Red Dog and Tara. The results and thermodynamic data suggest that the three concentrates contained significant amounts of the more reactive mineral wurtzite, although XRD analysis showed mainly the presence of the mineral sphalerite.

Jan 1, 1997