Search Documents

By Steven P. Oman

Large room and pillar mines are characterized by numerous and widespread working places. Ventilation requirements are high since each panel employs men and equipment that work simultaneously in multiple headings. Also, it usually is not feasible to redirect airflow from idle to active panels as the demands of each shift vary so every panel in the mine is fully ventilated at all times. Ventilation requirements will be even higher for mines that are classified as gassy. As a result of these considerations, ventilation systems for room and pillar mines are generally designed to handle large quantities of air. But as mining progresses and the mine be- comes larger, greater demands will be placed on the ventilation system. To insure that adequate ventilation is maintained at these times, ventilation engineers must anticipate problems and plan how best to deal with them.

Jan 1, 1983

By Yi Luo, Jian Yang, Hua Jiang

Surface subsidence events induced by underground longwall coal mining operations can cause various disturbances to surface structures ranging from integrity and stability to functionality problems. Highway bridges, as a kind of special road construction that can only tolerate smaller movements and deformations than road pavements, are particularly susceptible to severe influence caused by subsidence-induced ground movements and deformations. However, based on accurate subsidence prediction and correct influence assessments, efficient and effective mitigation and remediation measures can be designed and implemented to ensure the continuous service of bridges, safety of the travelers and smooth mining operations. In this paper, based on the predicted final and dynamic surface movements and deformations, the techniques to assess subsidence influence on the integrity, stability and functionality of bridge structures (e.g., decks, beams, abutments, etc.) are presented. A number of mitigation measures to protect the bridge structures are recommended along with an actual application case.

By I. Iwasaki

Differential flotation of bulk sulfide concentrates from Duluth gabbro into copper and nickel concentrates could be implemented by first destroying the hydrophobic coating with ozone and then by recovering the copper concentrate with a copper-selective collector. A number of parameters involved in the use of ozone; such as the sequence and the conditioning time of ozone treatment, the pulp pH, and the level of xanthate addition, were investigated.

Jan 1, 1985

By Ari Jokilaakso, Junjie Shi, Zhuo Chen, Pekka Taskinen, Xiang Gao

The amount of copper flash smelting slag has increased during the recent years along with an increasing slag-to-metal ratio. During slag tapping, some copper sulfide is mechanically entrained. As a result, it is necessary to recover copper matte from the slag by suitable methods. At present, the most common way is slow, controlled cooling in a transfer ladle. However, research on the detailed effects of slow cooling and the function of slag modification is rare. This paper described experiments that were performed at different cooling rates (0.5, 1.5, 3, and 7 °C/min), with and without additive. A detailed characterization of the copper-rich phase and its particle size was subsequentlymade using SEM-EDSmicrographs and image analysis software.With a decrease in cooling rate, the particle size of the copper-rich matte phase became larger. The addition of gypsum and carbon as a slag modifier affected the size of the copper-rich phase slightly, and its chemical composition was modified compared with the experiments without additive.

Jul 31, 2020

By Yong Pan, Srivatsan Jayaraman Sridharan, Purushotham Tukkaraja

Block cave mining method poses unique ventilation challenges compared to other underground metal mining methods. This research study focuses on assessing the airflow behavior in regulated airflow distribution systems by developing a 1:100 scaled block cave experimental model and a numerical model. This study also investigated gas flow behavior under various airflow conditions. Based on our findings, we observed that reduction in particle size and porosity of caved materials, decrease in cave footprint, and closure of undercut drifts would increase cave airflow resistance. The increased airflow is found beneficial for gas dilution regardless of its source locations, while the regulated airflow distribution system might deteriorate gas dilution situation when the source is located in the extraction drifts.

May 12, 2022

By P. Mousset-Jones

The USBH Mining Systems and Ground Control Generic Research Center funded a project leading to the improved planning of airflow and refrigeration in underground mines experiencing hot working conditions. The project was broken down into approximately five phases: 1. Visiting some of the known hot mines in the U.S. and sending out a questionnaire to determine other mines which might be experiencing hot working conditions in the future. 2. Choosing two mines in which to conduct measurements to determine the insitu rock thermal conductivity and diffusivity, and comparing these values with laboratory determined values. 3. Investigating computer programs available for mine climate simulation, and testing these programs with case study examples from the two mines where the rock thermal properties were measured. 4. Considering improved ways of estimating the wetness factor and experimenting with the use of heat flux meters to more directly measure the rock heat inflow into the airstream. 5. Applying the results of these investigations to simulating the climate for future mine development and production areas at the two- mines. The project is approximately two thirds completed. At the time of writing, the insitu measurements at one of the mines are still being recorded. This paper will be describing the procedures and results of the insitu rock thermal property measurements, and give a brief description of some of the simulated results obtained for a mechanised cut and fill stope case study from the Homestake Gold Hine in South Dakota.

Jan 1, 1985

By Peter G. Chamberlain

Domestic mining will not produce a significant portion of the manganese consumed in the United States unless new mining and processing techniques are implemented that will enable domestic lean ores to economically compete with rich foreign ores. One mining-processing technique that appears promising for certain deposits is in situ and/or heap leaching with aqueous SO2. Since leaching offers economic advantages of low capital costs, low operating costs, and short start-up times as well as environmental and safety improvements over conventional mining-processing, the Bureau of Mines studied the leachability of manganese deposits from several districts. Manganese oxides, hydroxides, and carbonates were leached to 80 to 90 pct recovery in 7 to 40 days of leaching with a solution containing 5 pct SO2 in column leaching tests. Preliminary cost analyses of surface mining-heap leaching, block caving-in situ leaching, and shrinkage stoping-in situ leaching indicate that the products of manganese leaching may be economically produced for the chemical and electrolytic manganese industries. The easiest marketable product to obtain would be a manganese sulfate commonly used as a fertilizer amendment. Manganese carbonates and hydroxides could also be precipitated from the pregnant leach solutions.

Jan 1, 1983

By Ali Ekrem Aritan

In this study, the vibration exposure of excavator operators working regularly in 25 different natural-stone quarries was measured. In addition, the relationship between vibration exposure and rock properties was investigated. Gloved and ungloved vibration measurements were performed and revealed that antivibration gloves reduce excavator operators’ vibration exposure by 7.10 to 25.95 percent. Samples from each quarry were characterized with rock mechanics tests. The correlations between the hand-arm vibration measurements and the natural stone’s physical-mechanical properties, such as uniaxial compressive strength, Shore hardness, Knoop hardness, apparent density and total porosity were determined to be more than 70 percent. One finding of the study was that the health risk in excavators cannot be reduced sufficiently by the sole use of antivibration gloves. Furthermore, the excavation of any rock with a Knoop hardness above 121 is associated with an 81 percent risk of hand-arm vibration. To increase awareness of the danger of vibration exposure for natural-stone miners, training programs should be provided, and technical and operational changes should be implemented.

By Thomas D. Boyce

Minewater from many western U.S. uranium mines often contains radioisotopes in concentrations higher than permissible for discharge to unrestricted areas. .Radium 226 has the lowest permissible concentrations of all radioisotopes and usually greatly exceeds this limit in untreated effluents. This radionuclide is derived from the natural radioactive decay of uranium: [ ] The treating of minewater effluents has been studied previously (1) and the classical removal method for radium has been adsorption on barytes or freshly precipitated barium sulfate. This paper describes the removal of radium from minewater by utilizing a selective complexer based on a crosslinked organic polymer matrix.

Jan 1, 1982

By H. Huang, R. N. Gow

"The reactivity of an enargite mineral electrode was investigated spectroelectrochemically under conditions typically found in alkaline sulfide leach solutions, with pH 11-13 and Na2S additions of 50 and 250 gL-1. A bulk enargite electrode was cycled between 0 and -1,000 mV for each set of solution conditions. Raman spectroscopy was used to determine and compare surface formations against species in mass-balanced EH-pH diagrams generated using STABCAL. Previously, it was determined that arsenic could be selectively leached under alkaline conditions at an average solution potential of -300mV, across the pH range 11-13. Operating under such conditions allowed for the selective leaching of arsenic with elemental sulfur formation. From several of the voltammograms obtained during this current testing, the formation of elemental sulfur appeared at increasingly reducing conditions with increasing sulfide concentration. At high concentrations, copper started to dissolve, possibly as a bisulfide complex, reducing the selectivity of the leach, unlike previous studies. However, the presence of the higher sulfide concentration is also anticipated to prevent passivation by consuming any surface formation of elemental sulfur. This study provides insight into the operating parameters of alkaline sulfide leaching in regards to the selectivity of arsenic leaching, as well as guidance for control of reagents and solution potential and, of course, the need for water treatment afterwards.IntroductionEnvironmental limitations on the pyrometallurgical processing of arsenic-bearing concentrates have forced operations to consider other solutions. Attempts to hydrometallurgically process enargite (Cu3AsS4) fall into two categories: the co-dissolution of arsenic and copper under acidic conditions, and the selective leaching of arsenic under basic conditions. The authors believe that the selective leaching of arsenic is more amenable because it produces a solid copper phase, preferably chalcocite (Cu2S) or covellite (CuS) that could then be processed using conventional methods already in place in the copper and gold industries. Potential leaching methods include alkaline sulfide leaching (Achimovicovica et al., 1999; Anderson and Twidwell, 2008a,b; Tongamp et al., 2009 and 2010), hypochlorite leaching (Vinals et al., 2003; Curreli et al., 2005; Mihaljovic et al., 2007), ammoniacal leaching (Gajam and Raghavan, 1983), and acid leaching (Gow et al., 2014b) with or without fine grinding to mechanically activate the enargite surface and increase normally slow leach reaction kinetics (Achimovicova et al., 1999; Balaz et al., 2000; Balaz and Achimovicova, 2006). In this study, the reactivity of enargite under alkaline sulfide leach conditions was examined."

Jan 1, 2015

By Cengiz Karagüzel, Ömer Canıeren

The mobility of gold and silver metals from refractory ores is very low due to free metal ions in their bodies that bind the transportable and free metal molecules or they are encapsulated in minerals such as sulfides, arsenosulfides, carbonaceous, and clayey materials which make it difficult to extract them. As known from the literature, the enrichment of oxide refractory gold, silver ores, Ag, and Au-rich flotation concentrated from sulfur refractory ores can be leached in the chloride-hypochlorite solutions. In this work, the leaching approach was studied to extract silver ions from refractory ores in the presence of hypochlorite media under high pressure. The mineralogical and scanning electron microscopy analysis of the sample indicated that the silver was encapsulated in barite and quartz minerals in fine sizes. In order to obtain the optimum leaching conditions for the silver ore, the effects of several parameters, namely, temperature, leaching time, NaCl and NaOCl concentration, solid ratio, and particle size on the leaching recovery were investigated in detail. The leaching experiments showed that the highest silver recovery of 62.35% was obtained under the following conditions: temperature of 150 °C, oxygen pressure of 1800 kPa, leaching time of 2 h, concentrations of 2 mol/dm3 and 0.4 mol/dm3 for NaCl and NaOCl, respectively, the solid ratio of 30%, and particle size (d80) 15 μm. The results obtained from this study indicated that the enrichment of refractory silver ores to extract the silver encapsulated in barite and quartz minerals could be possible in the chlorite-hypochlorite under high pressure, a relatively shorter leaching time compared to conventional cyanide leaching.

Jan 28, 2021

By Sean Harvey

One of the manifestations of the dynamically induced failures in deep coal mines is the violent ejection of coal from the ribs. A possible protection against such failures is the use of a specifically designed dynamic support system with reinforcement units having the sufficient capacity to absorb the kinetic energy of the dynamic failure and a skin support that can adequately contain the disintegrated coal. With this method of mitigation in mind, a recently introduced yielding rock bolt, trade name Roofex, has been identified (Harvey and Ozbay, 2009) as a possible energy absorbing component of a dynamic support system. According to the manufacturer?s specification, the Roofex bolts can yield 300 mm (or more) displacement while holding 80 kN pull load. In order to assess the performance of this support unit in coal ribs, a series of in situ pull tests performed in two coal mines in Colorado. The results show that, under conventional pull test loading conditions, Roofex yielding bolts perform very close to their claimed specifications, thus showing a potential for their use as the main energy absorbing component of a dynamic support system. Further studies are required to confirm the in situ performance of these bolts under dynamic loading conditions and also to develop a containment component for a dynamic support system for the mitigation of dynamic coal rib failures.

Jan 1, 2009

By Frederick Bradley Henderson

This study was initiated to investigate the occurrence of cinnabar in the oxidation zones of some mercury sulfide deposits. Seven mines or mine districts were visited and samples were taken from both the oxidation and primary zones of these deposits in order to compare their mineralogies and assess Vie chemical changes that took place during oxidation. As a result of the study of these specimens, several limiting factors are suggested for the chemical environments and processes active in both the deposition and oxidation of mercury sulfide deposits. The Mt. Jackson mine, near Guerneville, California (location map, fig. 1), was studied in some detail and forms the basis of this paper. The mine has not heretofore been described in detail in the literature. The Mt. Jackson mine is considered typical of mercury sulfide deposits occurring at the faulted boundaries of serpentinite bodies and enclosing sediments. Such mines are common in the California and Oregon Coast Ranges? Specimens collected by the author from the New Idria and New Almaden districts, the Mt. Diablo, the Culver Bear, and the Buena Vista mines in California, and the Opalite district (Cordero and Bretz, mines) on the Oregon-Nevada border were studied for comparison with the Mt. Jackson samples. The mine description, maps and sketches were composed from field maps kindly provided by Francis Fredericks, consulting geologist to the Sonoma Quick-silver Mine Inc. during the author's visit in 1962. Additional information was obtained from the company maps and minor corrections and interpretations were added by the author.

Jan 1, 1965

By Martin H. Stanczyk

The Organic Act of 1910 established the Bureau of Mines and gave it authority and responsibility for conducting research on separation, recovery, and recycling of waste products and scrap generated by the mineral and metals industries and the consuming public.(1)1 It was apparent to our Nation's leaders even then that mineral resources, once mined, are irreplaceable and that the development of methods for recycling the values contained in wastes would be required to solve the problem of even¬tual scarcity, Estimates of the increase in per capita consumption of mineral resources in this country indicate that the consumption of metals, minerals, and fossil fuels by 1980 will be double that consumed in 1970 (2). The United States can expect to meet its future mineral needs in three basic ways: the first is through increased production of primary raw minerals; second by increasing imports from foreign sources; and third by recycling secondary materials and metals that were formerly discarded as waste. Rather than consider these

Jan 1, 1972

By N. Damiano, C. Zhou, B. Whisner, M. Reyes

"The industrial Internet of Things (IIoT)—a concept that combines sensor networks and control systems—has been employed in several industries to improve productivity and safety. NIOSH researchers are investigating IIoT applications to identify challenges of and potential solutions for transferability of IIoT from other industries to the mining industry. Specifically, NIOSH has reviewed existing sensors and communications network systems used in U.S. underground coal mines to determine whether they are capable of supporting IIoT systems. The results show that about 40% of the installed post-accident communication systems as of 2014 require minimal or no modification to support IIoT applications. NIOSH researchers also developed an IIoT monitoring and control prototype system based on low-cost microcontroller Wi-Fi boards, to detect a door opening on a refuge alternative, activate fans located inside the Pittsburgh Experimental Mine, and actuate an alarm beacon on the surface. The results of this feasibility study can be used to explore IIoT applications in underground coal mines based on existing communications and tracking infrastructure. INTRODUCTION The nation’s approach to health and safety in mining has historically been reactive in the sense that health and safety regulations and mandates have traditionally been passed as a result of tragic mining accidents. An example of this is the Mine Improvement and New Emergency Response Act (MINER Act) of 2006, which was passed as a result of several mining accidents where tracking of and communications with underground personnel were severely limited. While this reactive approach has led to the development and implementation of highly impactful safety interventions and safety practices, there currently exists a technological revolution that can shift the paradigm toward a proactive approach based on preventative methods: Internet of Things (IoT). IoT is the network of physical objects or ""things"" embedded with electronics, software, sensors, and connectivity to enable that network to achieve greater value and service by exchanging data with the manufacturer, operator, and/or other connected devices [1, 2]. It should be noted that IoT has been defined from various perspectives, and hence numerous definitions exist in the literature. The apparent ambiguity of the IoT definition might be due to the fact that IoT is syntactically composed of two terms: internet and things. The first one pushes towards a network-oriented vision, while the second tends to put the focus on generic objects. The traditional internet can be viewed as an internet of computers —i.e., “things” connected to the internet are computers only. IoT “extends” the internet by allowing other generic things that are commonly found in our daily life, such as refrigerators and cars, to be interconnected via the internet, and thus creates a bridge between the virtual word and the physical world."

Jan 1, 2017

By Y. Zhang, M. Yekich, C. Zhou, C. Jobes, J. Galanko, D. Tuchman, J. Srednicki, J. Carr

The continuous personal dust monitor (CPDM) is an essential instrument for working in hazardous environments, is used to monitor real-time coal dust exposure, and is mandated by the Mine Safety and Health Administration (MSHA) for underground coal mines. Researchers from the National Institute for Occupational Safety and Health (NIOSH) found that it is possible for electromagnetic interference (EMI) between a CPDM and a proximity detection system (PDS) to occur. Various approaches have been taken by researchers and manufacturers to address this EMI issue. Administrative controls were recommended to keep the CPDM six inches away from the wearable PDS device. Shielding pouches were made to contain the electromagnetic (EM) emission from the CPDM. Metal shielding was added to major EM emitting components. EMI filtering with large capacitors was introduced to mitigate EMI. Most recently, a novel magnetic-field-cancellation-based approach was developed and achieved remarkable results. In this paper, we provide a comparison between these approaches. The pros and cons of each approach are presented and discussed, so that mining device manufacturers and operators can best evaluate the technology and controls that improve the health and safety of mine workers.

Feb 1, 2023

By Louis P. Gignac

The Lac Shortt gold deposit is located in Northwestern Quebec, at some 115 km west of the Opemiska Division and 380 km northeast of the Lac Dufault Division, as shown on Figure 1. Falconbridge's exploration crews drilled the first six holes in the gold-bearing ore zone in 1979. After further diamond drilling from surface in 1980, the decision was taken to carry out an underground exploration program. A three-compartment shaft was sunk to a depth of 340 metres in 1981 and 1982; it was followed by an extensive exploration program, which included 1073 metres of cross-cutting and footwall drifting, 645 metres of ore drifting and 11 200 metres of diamond drilling. The underground work was completed by mid-winter 1983. It was followed by a complete feasibility study of the Lac Shortt Project. After some $Can 14.2 millions in exploration expenditures, the Board of Directors of Corp. Falconbridge Copper approved in July 1983 additional expenditures of $Can 45 millions to bring the Lac Shortt Mine in production at the capacity of 261 000 tonnes per year. Gold price was $US 425 per ounce at the time.

Jan 1, 1985

By K. Osseo-Asare

LIX63 in combination with DNNS selectively extracts nickel and/or cobalt from acidic leach liquors with pH values as low as 1.0. Nickel/cobalt and cobalt/nickel selectivities are achieved by varying the relative concentrations of LIX63 and DNNS. Increasing LIX63 concentration retards both extraction and strip-ping rates while DNNS has the opposite effect. Slope analyses of equilibrium data indicate that both LIX63 and DNNS are present in the extracted complexes. Examples of possible flowsheets are presented.

Jan 1, 1978

By V

"Recent regulations, as well as a general aversion to central dust collectors within the Powder River Basin Coal user’s community, have created a need for an alternate method for eliminating airborne dust. This paper addresses the capital expenditure as well as the cost of ownership of an integrated point source air cleaning system in comparison to a central collection system. This assessment was conducted by comparing the cost to purchase and operate a central dust collection system and integrated air cleaner system on a typical multiple transfer point application. The central dust collector consists of a negative pressure blower, a series of filter bags, a collection hopper, a screw conveyor to place collected material back into the material stream, and a series of ducts to pull air and dust from individual pickup points. The point specific integrated air cleaners consists of a negative pressure blower to pull dust and air from an application point through a bag-less filter media located at the application point. The agglomerated material is then redeposited into the material stream at point of use without the need for ducting or a central material hopper. The assessment yielded a 54% reduction in capital expenditure and a 26% reduction in operating costs for the same application when using individual dust filters as opposed to a central system. In addition to the lowered cost, there are reductions in risk associated with the elimination of ductwork and the central containment enclosure for collected explosive dust. By the conclusion of this paper, the reader will have a better understanding of the quantifiable differences between a central dust collection system and a set integrated air cleaner systems. BACKGROUND Spillage has always been a problem in the bulk solids handling industry. As long as there have been conveyors, there has been spillage. Spillage is material that falls off a conveyor belt and creates a hazard in the environment around a conveyor belt."

Jan 1, 2016

By Roy A. Grancher

HAPPY BIRTHDAY Not only is 1971 the Centennial Year of the AIME, but it also marks the One Hundredth Anniversary of the United States Portland Cement Industry. On September 26th in 1871 David O. Saylor of Allentown, Pennsylvania, received his patent Numbered 119,413 for the manufacture of portland cement. "Cement" had been used in the United States before that. This was, however, natural cement - a direct product of rocks as found in nature, usually burned at low temperatures in open kilns. During the early 1800s this natural cement played an important role in such projects as the building of the Erie Canal. It was only after the Civil War that small amounts of high priced portland cement was imported from Europe. The successful use of this material in construction led to Saylor's experiments and subsequent patent for the manufacture of a scientifically controlled product in this country. These one hundred years have witnessed four major "ages" of cement . . . three of them occurring in the last quarter century since World War Two. The first age was the "Age of Development", a seventy-year period which saw the growth of cement and its concrete end uses as major construction materials. Next followed a period called the "Age of Demand" when, after the war, cement became in short supply relative to large building requirements. In effect a cement shortage existed. The decade of the Sixties proved to be the "Age of Reaction", with its courses of action coming in response to the problems that arose when the industry's expansion programs provided too much capacity. Today cement, and the concrete industries, find themselves entering the "Age of Reason". Overcapacity, low price, rising costs, and poor returns are several of the reasons behind that name, As these industries face the construction challenge of the Seventies, and beyond, the application of basic management principles (otherwise known

Jan 1, 1971