Search Documents

By W. M. Husslage

The permeability in the blast furnace shaft is adversely affected by low temperature reduction degradation of sinters. The fundamental cause is an expansion of the iron oxide phase resulting from reduction of hematite to magnetite. The present study showed that expansion behavior during the hematite / magnetite reduction step and the resulting microstructure are strongly influenced by the reduction temperature (viz. partial oxygen pressure), the reducing agent and the nature of the hematite. The reduction rate is of minor importance. A reduction mechanism is proposed, explaining the dilation behavior and the magnetite microstructure. The results can provide better insight into reduction degradation behavior.

Jan 1, 1998

By K. H. McDaniel, L. Griswold

The Waste Isolation Pilot Plant (WIPP) is adding a third fan to supplement its two existing main fans. The third fan will operate in parallel with the two existing fans. An engineering analysis conducted in 1995 identified the need for improved system availability and efficiency. The WIPP, located near Carlsbad, NM, is a US Department of Energy (DOE), Carlsbad Area Office, facility that is designed to permanently dispose of US defense-generated transuranic waste in a deep, bedded salt deposit. Engineers at the WIPP performed a feasibility analysis for modifying, supplementing or replacing its two main mine fans. Since the centrifugal fans were installed in 1988, multiple operational and performance concerns have been identified. A comprehensive engineering study was conducted (McDaniel et al., 1997) to identify and quantify operational concerns, evaluate possible alternatives and recommend an optimum solution. The study indicated that adding a third single-duty centrifugal fan similar to the two existing fans and equipping that fan with Inlet Van Controls (IVCs) was the best choice. This alternative provided the most desirable combination of operational readiness and improving system performance. The fan installation project accommodates several operational and scheduling con¬straints. WIPP was scheduled to receive waste in May 1998. This milestone is proceeded by an operational readiness review. Fan installation could not be allowed to compromise the WIPP 's ability to declare facility readiness. Therefore, operational disruptions during the system tie-in had to be minimized. All engineering for the project has been com¬pleted, and physical modifications were begun in July 1997. The project was completed in 1998.

Jan 1, 2000

By VIVEK KUMAR HIMANSHU, M. P. Roy, P. K. Singh, A. K. Mishra, RAVI SHANKAR

Blasting with the aim to reduce oversize boulders in underground has many hurdles due to limited accessibilities and poor site conditions. Optimized drilling and blasting parameters can help to achieve this objective. The major challenges of the blast designers lie within deciding blast geometry, namely drill hole diameter, burden, and spacing. The general approaches covered worldwide to determine burden-spacing are based on various rules of thumb, which are based on previous experiences of blasts and the associated outcomes. However, many parameters influencing optimum burden-spacing to achieve desired fragment size are site specific. Sometimes drill geometry is decided based on associated blasting hazards rather than rock fragmentation. The Kuz–Ram model is a worldwide accepted rock fragmentation predictor. The parameters associated with this predictor also include burden-spacing for a blast. Back calculation of burden-spacing from the Kuz–Ram model can be used to achieve desired fragment size. This paper deals with burden-spacing determination by using an empirical approach for the underground stope ring blasting.

Jan 4, 2020

By Alvaro Lucio

The continuous increase of the fuel oil price compelled CV3D to look for an alternative fuel. Charcoal was selected as the alternative energy source. This paper justifies its selection, describes charcoal properties, the methods for using charcoal in the pelletizing and shows the results of the in-plant tests.

Jan 1, 1982

By TUIJA MONONEN, LUDGER BENIGHAUS, CHRISTINA BENIGHAUS, Virginia del Rio, SARI KAUPPI, JUHA M. KOTILAINEN, JAVIER GÓMEZ, JARI LYYTIMÄKI

The understanding of public debates over mineral exploration and mining largely originates from exceptional situations such as mining accidents of conflicts. Less is known about how mining is portrayed and understood under more conventional settings. What storylines dominate the local day-to-day public debate? This article presents results from a comparative case study focusing on newspaper coverage of mineral exploration and mining in three European countries representing different geological and socio-economic contexts. Newspaper articles from the Geyer-Erzgebirge region in Germany, the Andalusia region in Spain, and Northern Finland are studied. The sample looks into the period between September 2018 and February 2020 and shows that regional newspapers report about mining issues relatively intensively even in the absence of major accidents or other media events causing peaks of attention. The tone of the articles is generally neutral to positive towards mining activities, reflecting the specific local settings, historical experiences, and future expectations. Despite the different contexts of the three countries, there were considerable similarities to the topics highlighted, including common themes of mining revival, mining events and social interaction, history of mining, and damages related to mining. Past, present, and future employment opportunities related directly or indirectly to the mining sector are key storylines. Another recurrent underlying theme is the need to balance environment and safety risks and socio-economic prosperity, typically covered through ordinary disputes among the mining sector, public authorities, regional non-governmental organizations, and local initiatives.

Jul 6, 2021

By Russell Frith

The entire subject area of micro-seismic events due to stored strain energy, as distinct from gas-driven coal outbursts, can be readily sub-divided into firstly events with their energy source from within the coal seam (termed “bursts”) and secondly, event with their energy source outside of the coal seam in either the overburden and/or floor strata. The reason for sub-dividing micro-seismic events in this manner is that if the causation mechanisms and associated geotechnical conditions are materially different, then effective pre-mining predictions and subsequent operational controls may also differ. Attempting to explain a multitude of micro-seismic event types without consideration of varying source mechanisms will inevitably lead to inadequate causal explanations and effective controls.

By George J. Skoronski

The economics of pellet plant operation, in terms of fuel and power consumption, flexibility in the selection of the cheapest fuel source, system availability, maintenance costs, and the simplicity of process design, contribute to the determination of building and profitably operating a pellet plant. Design innovations, sup- ported by actual field data, have been initiated into the GRATE-KILN System design to positively address these factors. This paper presents the recent state of the art design concepts which have helped the GRATE- KILN System assume worldwide acceptance status.

Jan 1, 1983

By S. C. Sun

A process was developed to recover coal, clays and pyrite from coal wastes. The process consists of fine grinding followed by coal flotation and pyrite flotation leaving the clays in the flotation pulp. A bituminous coal refuse, containing l0% S-30% C*, was treated by this method to yield a coal product containing 4% sulfur, 10% ash; a pyrite product containing 45% sulfur (84% FeS2), 1% carbonaceous material and a clay product containing 2% sulfur (3.5% FeS2). The coal yield was about 89%. The pyrite yield was about 77%. The process steps may be entirely flotation, or gravity separation (hydrocyclone) may be used to increase the pyrite: coal ratio in the flotation feed. Cost estimation shows a profit of $2.28 per ton of low pyrite grade refuse (Labor, maintenance, overhead and plant depreciation were not included). The development of this process consisted of three parts: 1) exploratory tests, 2) optimization tests and 3) confirmatory tests.

Jan 1, 1968

By Robert Stefanko

The Federal Coal Mine Health and Safety Act of 1969 had far reaching effects upon many aspects of mining, ventilation being no exception. In this paper, good ventilation procedures are briefly reviewed, and attention is focused on the changes brought about by the new Act. By way of illustration the ventilation system for a typical Pittsburgh Block system is developed and the requirements of the fan determined. This is then solved by an available computer program, and the application is evaluated. Figure 1 represents a projected system for a coal property 1 by 3 miles in plan at a depth of 1000 feet with a coal thickness of 6 feet and desired daily tonnage of approximately 7200 tons on a two-shift basis. Only one half of the mine is shown (north area) with a mirror image mining arrangement to be developed concurrently for the south area. Six working units are projected, three in each area, one on pillar extraction, another developing panel entries and a third on main entry development. A two-split system is used for each working section so that the continuous miner and bolting crews each have a separate split of air, and no equipment need pass through a line brattice. The old requirement of 6000 cfm at the last open crosscut has been increased to 9000 cfm, and for the first time a minimum quantity (3000 cfm) is stipulated at the face thus requiring either line brattice or an auxiliary fan. With the respirable dust requirement limited to 3 mg/m3, the use of a blower system is precluded and exhaust systems are virtually the only choice. Maintaining the line brattice within 10 feet of the working face at all times as required by the new law has a definite effect on the mining cycle and is most difficult at best. In the highly gaseous Pittsburgh seam located in south-western Pennsylvania and northern West Virginia quantities of 20,000 cfm per split are not uncommon to maintain the methane percentage below the required l%

Jan 1, 1972

By Wen Tao Liu, Tong Tian, Fu Sheng Niu, Xiu Man Liang

The level of automation employed in flotation production is relatively low. In an actual concentrator, operators use their judgment to adjust the production state based on the visual characteristics of the flotation froth surface. There are shortcomings, such as strong subjectivity and lagging process operation, that easily cause the waste of manpower and material resources. Machine vision technology is introduced to replace human visualization, achieving a quantitative description of the visual characteristics of the froth surface. The state variable parameters are provided for the identification of the flotation conditions.

By Russell W. Hunt

The cave man of ages past took his wife-and family from the cave pointing to a fire he had built and beating on his breast said, "Look what I have done". Today man is taking his family back to a cave saying, "Come enter in because of what I have done". At the close of World War II Germany said if they had gone underground one year earlier with more of their operations, the war could have lasted four years longer with perhaps much of Britain devastated. The protection of the home front no longer rests with the soldier in actual combat. The battle will be won at home with the most careful kind of protection against missiles. After Nagasaki-Hiroshima Sir Winston Churchill said in substance "Up to now the Almighty has mercifully withheld from man the knowledge of these terrible weapons of destruction."

Jan 1, 1959

By Ronald M. Hays

The White Pine Copper Division of Copper Range Company is a large copper producer operating an underground mine, mill, and smelter on Michigan's Upper Peninsula. Principal water discharges are from the tailings basin where these discharges are high in dissolved solids because of mine water pumped into the basin. Principal air emissions are from the smelter where SO2 emissions are uncontrolled. Although water discharges and air emissions have not had significant environmental impacts, environmental regulations could require additional control procedures. Because of low copper prices and poor profitability, cost of compliance with possible new environmental regulations could have serious impact on White Pine with no apparent significant beneficial environmental impacts.

Jan 1, 1979

By R. K. Sinha, B. S. Choudhary, Desh Deepak, A. K. Mishra, Hemant Agrawal, Shankar Kumar

There are several methods (empirical, statistical, and machine learning tools) to calculate blast-induced ground vibration. Still, due to complications in the blasting procedure, under varying blasting loads and strata conditions, it is not easy to predict and simulate blast vibration precisely. Therefore, a study was conducted to simulate the field blast data in Ansys software using explicit dynamics. For this study, monitoring of ground vibration for 20 single hole blasts was carried out. The density of emulsion explosives was in the range of 0.9 to 1.15 g/cc. In the laboratory, rock properties were determined from the rock sample collected from the mine site before blasting. The in-hole velocity of detonation (VoD) and the density of the emulsion explosive were also determined. These parameters were used for numerical analysis to know the ground vibrations at specified points. The results of ground vibration predicted by the model are validated using field data.

By L. G. Austin

The model originally proposed by Austin, et al., has been modified in the light of further investigation of the breakage laws in SAG milling. The model uses a fully-mixed reactor for short L/D mills and calculates the breakage of small particles by the nipping action of balls and pebbles. The autogenous self-breakage of larger lumps is treated as an effective means of fast breaking rock and much slower breaking rock. Experiments show that fast autogenous breakage can be treated as a first-order breakage with an overall specific breakage rate which incorporates fracture and chipping. Similarly, slow breakage incorporates fracture and abrasion. Autogenous breakage is cushioned by the accumulation of fine material. Simulation results are compared to results from tests in a 2 m diameter continuous pilot-scale SAG mill. Future work is discussed.

Jan 1, 1985

By M. N. Nabighian

Utilization of x-ray diffraction data for mineral identification has been well documented and accepted as an analytical tool in industrial and research organizations. However, the search for new methods to minimize errors affecting measured reflection intensities is being carried out by all concerned. Recent application of computer capability has greatly reduced the time required in handling data for mineral analysis and has increased the capability of accepting more data for greater precision. The purpose of this communication is (1) to describe the concept of cross-power in XRD analysis, and (2) to show that direct comparison analysis for multiphase systems has improved analytical accuracy when all available x-ray diffraction data are used in conjunction with high speed data processing by computer.

Jan 1, 1972

By K. D. Luxbacher, E. C. Jong

Perfluoromethylcyclohexane (PMCH), a member of the perfluorocarbon tracer group of compounds, has been shown to be a viable supplement to the widely used tracer gas sulfur hexafluoride (SF6). This viability stems from the fact that PMCH can be used concurrently with SF6 while maintaining adequate chromatographic separation and comparable sensitivity during analysis. However, the release of PMCH in an underground mine ventilation system is challenging due to its physical characteristics. While SF6 exists as a gas at room temperature and pressure and can be accurately released by a variety of means, PMCH exists as a volatile liquid at room temperature and pressure, preventing it from being deployed in a similar manner. One method to release PMCH is to use a permeation plug passive release vessel (PPRV), which allows for the controlled release of the gas. This paper presents the results of a study evaluating various preparation techniques, plug thicknesses and plug materials of an aluminumvessel PMCH release source, so that a source appropriate for the mine scale may be developed.

Jan 1, 2015

By H. Huang, R. N. Gow

"EH-pH diagrams are useful tools in understanding how mineral surfaces react in solution and particularly how aqueous conditions can be changed to enhance mineral leaching processes. Successful application of these diagrams, however, requires that several considerations be kept in mind to prevent what had been termed as “gross errors” in their calculation and use. In this paper, the aqueous Cu-S system is used as the basis for explaining the mass-balanced method of calculating EH-pH diagrams with the STABCAL thermodynamic equilibrium software. A breakdown of the Gibbs’ Phase Rule and how it is used in STABCAL to modify the diagrams is included. The methodology was applied to the aqueous Cu-As-S system, and resulting diagrams were compared against examples of those generated using the predominant-ion method. The complexity of such diagrams increases with every additional component, and competition between species becomes more apparent, as can be seen by curvature in the resulting mass-balanced diagrams. The complete diagram for enargite (Cu3AsS4) is shown. It compares well with spectroelectrochemical measurements from Raman spectroscopy and cyclic voltammetry studies.IntroductionInnovation in the field of processing arsenicbearing copper ores has been of particular interest. Copper arsenic sulfosalt minerals such as enargite (Cu3AsS4) and tennanite (Cu12As4S13) are now frequently prevalent in ore bodies as the oxide and easily leachable sulfides become harder to find. These minerals, unless pretreated somehow, concentrate in copper sulfide flotation processes, in turn concentrating the arsenic levels. Increasing environmental restrictions on arsenic content for smelters makes the hydrometallurgical processing of these concentrates more favorable. While enargite is considered one of the more refractory copper sulfides, more so than chalcopyrite (CuFeS2), there are still several methods, both industrially proven and in development, that are capable of processing these ore types. Alkaline sulfide leaching can be used as a pretreatment method to solubilize arsenic selectively (Delfini et al., 2003; Anderson and Twidwell, 2008; Tongamp, Takasaki and Shibayama, 2010a, 2010b), or the entire metal content can be leached using acid-type leaches such as acidified ferric sulfate (Dutrizac, 1981; Hackl et al., 1995; Klauber, 2008), or the chloride assisted, CESL (McDonald and Muir, 2007) or nitrogen species catalyzed (Anderson, 2003) processes can be used.As development of these leaching technologies proceed, it is also important to develop an understanding of the mineral thermodynamics. To date, there are numerous studies on the Cu-Fe-S-H2O system, particularly as it relates to chalcopyrite leaching, yet few studies have done on the Cu-As-S-H2O system. Computer-generated EH-pH diagrams have been employed to illustrate the importance of thermodynamic calculations in providing insight into such a system."

Jan 1, 2016

By Shailendra Chawla, Ashok Jaiswal, B. K. Shrivastva

The study aims to evaluate the pillar behavior during the depillaring operation by continuous miner (CM) technology. A panel with five headings developed as per the coal mine regulation of Indian coal mines [2] has been selected for the study. The depillaring operation has been carried out using CM technology after widening and heightening the original entries. An extensive field investigation has been carried out throughout the depillaring operation to access the mining conditions. Depillaring operation has been performed smoothly up to the middle of the panel (fourth row out of eight rows of four pillars each). Advanced blinking of the auto warning tell-tale (AWTT ) has also been observed on some of the instruments during the splitting of pillar no. 18. The panel shows extremely difficult mining conditions at this stage. The case has been numerically simulated using three-dimensional numerical techniques. The simulation result has indicated the high stress and yield condition on the working and the barrier pillar (surrounding goaf from both sides) after the extraction of pillar no. 18. The analysis has also indicated the marginal stability of the 2nd barrier pillar (namely “pillar B”). The failure of the barrier pillar could be the responsible for global instability of the panel as observed in the field. Understanding the importance of the barrier pillars, panel design has been modified by incorporating an additional row of barrier pillars. The stability of the modified panel has been evaluated. Both working and barrier pillars have been observed stable in the modified panel. This could be an alternative layout considering safety at the working face.

May 8, 2022

By P. Bissert, M. Klein, L. Yan, D. Yantek, R. Matetic

"U.S. Mine Safety and Health Administration (MSHA) regulations require underground coal mines to use refuge alternatives (RAs) to provide a breathable air environment for 96 hours. One of the main concerns with the use of mobile RAs is heat and humidity buildup inside the RA. The accumulation of heat and humidity can result in miners suffering heat stress or even death. MSHA regulations require that the apparent temperature in an occupied RA not exceed 95 °F. To investigate this, the U.S. National Institute for Occupational Safety and Health (NIOSH) conducted testing on a 23-person tent-type RA in its Experimental Mine in a test area that was isolated from the mine ventilation system. The test results showed that the average measured air temperature within the RA increased by 9.4 °C (17 °F) and the relative humidity approached 94 percent at the end of a 96-hour test. The test results were used to benchmark a thermal simulation model of the tested RA. The validated thermal simulation model predicted the volume-weighted average air temperature inside the RA tent at the end of 96 hours to within 0.06 °C (0.1 °F) of the average measured air temperature. IntroductionIf an accident occurs in an underground coal mine, miners who fail to escape from the mine can enter a refuge alternative (RA) for protection from adverse conditions, such as high carbon monoxide levels. One of the main concerns with the use of mobile RAs is the potentially adverse thermal environment inside an RA from the metabolic heat of the occupants and the heat released by the carbon dioxide (CO2) scrubbing system. Moreover, the humidity within the RA will increase through occupants’ respiration and perspiration, and from the chemical reaction within the CO2 scrubbing system. The accumulation of heat and humidity can result in miners suffering heat stress, heat stroke or even death."

Sep 1, 2016

By J. K. Hrica, T. J. Orr, J. Navoyski, B. Macdonald, C. L. Hoebbel, J. L. Bellanca, B. Demich

Haul truck fatal accidents and injuries continue to be a significant concern for the mining industry. However, the availability of high-quality training materials continues to be limited. Near-miss incident accounts, if packaged well, could help fill this gap, because for every fatality, there are hundreds of reportable accidents and thousands of undocumented near misses. Researchers from the National Institute for Occupational Safety and Health (NIOSH) collected detailed accounts of 21 near-miss incidents in virtual interviews with mineworkers at surface mining operations across the country. From these interviews, researchers created four simulation videos. The videos bring these events to life through first-person retelling and various visual perspectives of actual events. Each video exemplifies a critical safety message and a common haul truck hazard. This paper describes the process of taking narratives and turning them into impactful visual stories. NIOSH plans to co-release these simulation videos with the Mine Safety and Health Administration (MSHA) to the mining industry to raise awareness and ultimately help reduce haul truck-related accidents and fatalities in mining.

Feb 1, 2023