Search Documents

By Thomas N. Walthier

Exploration is the systematically financed and technically oriented search for mineral wealth. Almost all established mining companies have an exploration department. The size of a company's search varies over the years as the company's profits, or the corporate philosophy change. While the established mining companies have exploration departments, they are also alert to acquiring discoveries made by others -- especially by prospectors and small companies without the resources to develop their find. The emphasis in some large companies stresses self-generated discoveries while others rely heavily on acquisitions; again, over the years the emphasis may alternate. In the last analysis, essentially all new mineral wealth was found through someone's exploration effort. Before we discuss how exploration is financed, it will be informative to analyze how discoveries have been made and by whom. Recently, the author conducted a survey of randomly selected major mining companies to answer these questions. Most companies responded and many went to considerable effort to give complete and detailed answers. I thank all for their help and cooperation. The questionnaire is attached as Appendix I. Appendix II is a list of the 400 companies that replied in a complete enough manner and format to be analyzed here. The results of the questionnaire are given in Table 1. Over 57% of the new orebodies acquired by 40 major mining companies during the past quarter of a century were generated

Jan 1, 1977

By J. G. Groppo

A series of performance studies have been conducted using counter-current column flotation to recover a marketable clean coal product from existing preparation plant fine waste streams. The test work was conducted at several preparation plant sites in Kentucky and Virginia and utilized a 0.15m (6 in.) I.D. column that was 5.79m (19 ft.) high. The refuse streams tested included both thickener feed and classifying cyclone overflow with a typical size distribution of 100 mesh X O. The percent solids of the column flotation feed varied from 1.5 to 15% while the ash content ranged from 30-60%. The concentrates produced contained 2-10% ash with BTU recoveries of nearly 90% using 0.12-1.25 kg/ton (0.25-2.5 lbs/ton) fuel oil and 0.12 kg/ton (0.25 lb/ton) MIBC. These results were consistent with or better than results obtained in preliminary laboratory scale column flotation evaluation. Test results from 7 different seams are discussed as well as scale-up relationships utilized to design a full scale installation presently in operation.

Jan 1, 1990

By J. Fuller, J. Beale, Q. Justice, Z. Agioutantis, S. Hicks, Z. Khademian

Seismic events can be induced by mining due to unstable rock failures or slips along geologic structures leading to the sudden release of strain energy stored within the rock near underground openings. Depending on their intensity and proximity to the working area, seismic events may raise safety concerns, and thus the forecasting of the seismic potential in advance of mining can mitigate safety hazards. The integration of seismic data into geomechanical modeling can provide a tool for identifying areas with elevated potential for seismic activity. In previous works, a methodology was developed to forecast seismic potentials in a pseudo-2D geomechanical model. In this paper, seismic events, ranging in magnitude from about -1.0 ML to 3.7 ML, recorded in a deep longwall mine (> 450 m) in Virginia during mining of six adjacent panels, were evaluated to identify areas where larger magnitude events (> 1 ML) had occurred. A three-dimensional geomechanical model of the same area was constructed in the 3DEC software to calculate the state of energy in the system with the progress of mining along the entire length of each panel. The variation in the energy content of the model was monitored, and zones with potentially damaging slip-type events along bedding planes followed by compressive-type events in the sandstone roof are the mechanism for large seismic events in the studied mine. The locations of anomalous events corresponded to the regions where both compression-type SPI (C-SPI) and slip-type SPI (S-SPI) were elevated. The modeling results were compared with the recorded seismic events to evaluate the model performance in forecasting the seismic potentials. The model was able to forecast 100% of regions with elevated and moderate seismic potential and 89% of regions with low seismic potential. This shows the applicability of energy balance calculations for forecasting the approximate location and timing of destructive seismic events in advance of mining.

Jun 25, 2024

By MOHAMMAD R. H. GORAKHKI, CHRISTOPHER BAREITHER, MANUEL APARICIO, IV JOSEPH SCALIA

Comingling filtered tailings and waste rock in a tailingsdominated mixture is a mine waste management strategy that has the potential to create geotechnically and geochemically stable landforms. Potentially acid-generating (PAG) waste rock can be sequestered within a filtered tailings matrix to enhance water retention and decrease hydraulic conductivity relative to a waste rock pile, potentially minimizing acid rock drainage (ARD). Enhanced water retention can reduce oxygen ingress limiting oxidation and resultant acid generation. Reduced hydraulic conductivity can slow inward percolation and outward drainage. In dry climates, the tailings matrix can hold precipitation near the ground surface accessible to evaporation and transpiration, thereby decreasing percolation. This paper presents an evaluation of comingled filtered tailings and waste rock in a tailings-dominated mixture (termed GeoWaste herein) and illustrates that ARD can be reduced under field conditions in a subtropical–highland climate.

By Clinton Birch

The multiple-criteria decision analysis is a technique that helps to find an optimal solution by evaluating conflicting criteria. In this study, an approach to perform multiple-criteria decision analysis for cut-off grade optimization, which considers the diverse stakeholder groups prevalent in the mining industry, is presented. The optimization model developed in this approach links the resource block model to the financial model, enabling the process to either maximize profit, net present value, revenue to the State, or extend the mine's life. To identify the optimal cut-off grade in each case, the Excel Solver function is utilized. Although it has limitations, the Solver function can still be modified to handle models with thousands of block values for determining input variables based on the target value. Following stakeholder engagement and dialogue, a single weighted average cut-off grade can then be determined. This approach is demonstrated for nine South African Witwatersrand gold mines.

Jun 25, 2023

By RICKARD HANSEN

With vehicles frequently found in underground mines and tyres being a major fuel item, the risk of tyre fires will be severe underground. This study presents an in-depth analysis of tyre fires on mining vehicles to increase the knowledge of the risk, applying data from full-scale fire experiments and CFD simulations. It was found that the wheelhouse of the loader caused an increase in the flame tilt angle of approximately 10%, decreasing the flame impingement and heat flux downstream. The flame temperature of the drilling rig tyre was found to be approximately 7% higher than the loader tyre, increasing the risk of igniting adjacent fuel items. The construction of the wheelhouse/mudguard will contribute to a longer flame length by creating a fuel-rich environment. The CFD simulations predicted higher flame tilt angles for the drilling rig case for higher flow velocities, indicating the influence of a varying wheelhouse/mudguard construction and tyre geometry on the flame tilt angle. The construction of the loader resulted in a flow behaviour, where the short distance to the front mudguard/tyre and the separation of flow directly downstream of the protruding construction led to fire gases being steered past the front mudguard/tyre. In the drilling rig case, the longer distance to the front mudguard/tyre led to fire gases being directed towards the body of the vehicle after passing the area with flow separation. An increased knowledge of the tyre fire risk on mining vehicles and mitigating measures would improve the fire safety in underground mines.

Feb 10, 2022

By J. B. Yianatos

This paper addresses the impact on performance of column height (H), and column height to diameter (H/D) ratio by modelling the effect of HID on mixing and consequently on recovery and grade. Mineral recovery increases with increasing H/D ratio for a constant column volume and feed flowrate, while the concentrate grade decreases to a minor extent. Columns 10-15m in height with H/D-10 are well suited for feed rates 150-600 L/min. Maximum H/D is determined by the gas carrying capacity, an important consideration for pilot units where H/D?200.

Jan 1, 1987

By H. Lawrence

In 1977, the Bureau of Mines awarded a grant to the State of South Carolina to explore the possibility of using Landsat multispectral scanner (MSS) data as an aid in monitoring surface mining activities in selected counties of the State. Work had been done in Aiken County prior to the grant by Bureau of Mines and State personnel at the EROS Data Center using both the GE Image 100 and ESL IDIMS systems. The initial work on the 1-100 consisted of locating and measuring the areas of various kaolin mines. The results were excellent on location, identification, and accurate area measurements of several mines as compared with aerial photos of each mine. The effort also included locating and measuring the size of all mines (including sand and gravel) within two U.S. Geological Survey (USGS) 7 ½ min quadrangle maps. Line printer overlays using the IDIMS equipment and software resulted in the location of all known mines within an estimated error less than ±91.4m (5300 feet). Mine acreage was calculated by counting each symbol (which represented one pixel) and multiplying by 1.1 (the number of acres per pixel). Figure 1 shows a portion of one quadrangle overlay. Table I gives a comparison of acreage measured for sever- al mines from the 1-100 and IDIMS systems vs. aerial photo measurements.

Jan 1, 1979

By Dejan Petrović, Pavle Stojković, Jelena Ivaz, Saša Stojadinović

In spite of the fact that flyrock phenomenon represents the real threat for personnel and machinery, it still remains insufficiently investigated. There are efforts, in the mining community, to explain the causes of flyrock, but the models capable to accurately predict flyrock occurrence and define the flyrock distance still do not exist. This article is an attempt to establish such a predictive model. The model utilized the adaptive nature of artificial neural networks and combined it with the accuracy of numerical modeling of physical phenomena. Necessary data were collected by high-speed camera recordings of actual blasts at three different surface mines and processed for further use for artificial network training. The result was a neuro-numerical couple which was capable to predict flyrock occurrence, estimate the launch velocity of flyrock fragments, and calculate the maximum distance of flyrock fragments. The safe distance was then calculated by multiplying the flyrock distance with a factor of safety. The article explains the procedure for data acquisition and processing, artificial network construction, training, and validation. It also explains the principles of flyrock distance calculation and, finally, provides a definition of factor of safety and safe distance. The results showed that the prediction was satisfactorily accurate and reliable.

Oct 22, 2021

By L. J. Drew

The plate tectonic setting, regional geology, and certain aspects of the economic geology of the iron-rare-earth-nio-bium ore bodies at Bayan Obo, Inner Mongolia, China, were studied by a team of geologists from the Tianjin Geologic Research Academy and the U.s. Geological Survey between 1987 and 1989. These ore bodies were formed by hydrothermal replacement of Middle Proterozoic dolomite in an intracontinental rift setting. A variety of veins and/or dikes that have a carbonatite-like mineralogy cut the footwall clastic rocks and migmatites. A stockwork of veins occurs at several locations in the footwall. The hanging wall is a shale that has been converted to a K-metasomatite and has microcrystalline potassium feldspar as its principal constituent. This shale served as a sealing caprock that contained the chemical solutions that reacted with the dolomite and that created the enormous concentration of mineralized rock in an 18-kilometer-long syncline. The rocks that host these ore bodies and the associated mineralized areas occur today as roof pendants in granitoid rocks of Pennian age that were emplaced during a continent-to-continent collision during that period.

Jan 1, 1991

By D. M. S. Bhatia

Five sulfide minerals from the Magiwnt mine, southeast Missouri were analyzed for 31 trace elements in over 300 samples by laser microprobe spectrographic analysis of polished sections. The concentration of several trace elements shows a pattern of progressive variation with depth (space) and variation with different paragenetic stages (time) of each mineral. Factor analysis of the geochemical data shows sympathetic correlation both in space and in time of Bi, Cd, Ge, and Sn in galena and sphalerite, and Ni and Co in sphalerite and marcasite.

Jan 1, 1979

By H. B. Miller

Contract Incentives have long been employed in the underground hardrock industry as a tool to influence employee performance, enhance productivity, and control labor costs. While traditionally structured to establish a direct correlation between performance and compensation, many contract programs have evolved into elaborate systems that promote strategies often viewed as independent of productivity. This paper presents the findings of research into these contract incentives and was conducted with the cooperation of 33 mines utilizing a spectrum of employee compensation and incentive programs. Emphasis of this analysis focuses on the types of production contracts observed and their role with respect to employee earnings.

Jan 1, 1994

By David R. Delling

Introduction In 1967, Tenneco acquired Kern County Land Co. The primary reason for the acquisition was to obtain Kern's agricultural, manufacturing, and oil interests. Included in the Kern portfolio were the core of Tenneco's present sodium leases in Sweetwater County, WY. This lease base has been ex¬panded and now consists of 62 km2 (24 sq miles). Beneath this property lies more than 500 Mt (550 million st) of economic trona ore. Following the Kern acquisition, Tenneco continued exploration and feasibility studies concerning the trona leases. The effort was accelerated in 1976. Tenneco was attracted to trona because of the favorable lease position it held, the growth rate of the Wyoming industry during the 1960s and 1970s, and the prospects for a long-term, stable business enterprise. The reserve picture was certainly attractive to a company long accustomed to the never-ending struggle to replace oil and gas reserves. In 1978, Wyoming was a boom area that had experienced rapid growth for a number of years. Unemployment was very low and vacant housing nonexistent. The prospects for soda ash were somewhat different in the 1970s than now. But it was recognized even then that a new producer would have a challenging task to compete in this business. Tenneco knew the capital burden required to build a grassroots facility during inflationary time, would have to be offset elsewhere Since labor and energy are the dominant direct costs in mining trona and producing soda ash these factors have always received a great deal of attention. Contracting and permits Environmental monitoring on the site began in late 1977. With the already mentioned considerations in mind, engineering began by mid-1978. Brown & Root Inc. was selected as the general contractor for the project. S. A. Scott & Co. was the engineering subcontractor for the mine shafts, hoists, ventilation system, and miscellaneous mine facilities. Frontier-Kemper was awarded the contract for sinking the two mine shafts. Acquisition of numerous federal, state, and local permits occupied all of 1978 and 1979. The Wyoming Industrial Siting Permit, which addresses socioeconomic issues, drew the most public interest. Siting issues were all satisfactorily resolved by negotiating reasonable stipulations with various local governmental units, school districts, and the like. Site location The Green River project location is not truly remote. It is located within 5 km (3 miles) of Interstate 80 and only about 32 km (20 miles) west of the city of Green River. Nevertheless, a substantial investment had to be made in communication and utility links to the site. These included: • A 14-km (8.5-mile) rail spur connecting with the Union Pacific Railroad at Bryan, WY. This spur has four bridge structures including one crossing Interstate 80. Most soda ash is shipped by rail, and coal is received over this line as well. • A paved 5-km (3-mile) roadway connecting to Interstate 80. • A powerline extension of about 27 km (16.5 miles), along with two new substations. • A 24-km (15-mile) waterline connecting the plant to a pump station on the Green River. The site is located on gently sloping terrain at an elevation of about 2.1 km (6800 ft). Ground conditions are good for construction. Weathered bedrock lies near the surface in most places. Geology The general geology of the Green River Basin has been well described previously. Tenneco's ore is in several superimposed evaporate beds. But the bulk of it is present in Bed 17, located about 457 m

Jan 10, 1985

By D. Nutakor

This paper presents the results of a study conducted on a slope failure that occurred in the Q7 mining cut at Rio Tinto's Bingham Canyon Mine. The slope failure occurred in a weak rock mass with an estimated rock mass rating of 25%. The failure mechanism was of the circular type, involving ten 15-m (50-ft) benches and covered a total width of 152 m (500 ft). The analysis used Adam Technology's photogrammetric method with a two-dimensional rock fall simulation program (RocFall software) to design a 3-m- (1 0-ft-) high berm located 7 m (24 ft) from the toe of the failed mass. Back and predictive analyses were performed on a cross-section through the slide using Slope/W software, resulting in flattening the interramp angle (IRA) from 44° to 38°. This design modification produced a factor of safety (FOS) of 1.14. Sensitivity analysis involving FOS vs. pore water pressure showed that FOS is sensitive to water saturation. A dewatering system using a series of horizontal holes drilled below the slide and dewatering holes drilled from a drainage gallery has since been established to improve the stability of the slope. Throughout the one-year period since this investigation, no significant slope movement has been detected by the slope stability radar, and mining is in progress below the failure.

Jan 1, 2012

By Fred W. Brackebush

In underground stopes that require more than minimal support, backfill is almost universally used. The term cut and fill stopingis used in a broad sense in this section, which describes underground mining methods requiring support. Support in stopes can be classified as local or short-term and general or long-term. Local support for the back of a stope, for example, can be accomplished with rock bolts or timber stulls. General support for the walls of the stope is provided by backfill. Local support provides a safe working place for the stope miners. General support, provided by backfill, preserves the access way to the stope and prevents large scale dilution of ore. Supported methods are a set of cut and fill stoping methods using backfill for general support and various local support methods. his section is subdivided into three chapters: 19.1 Cut and Fill Mining 19.2 Excavation Techniques 19.3 Backfilling Methods

Jan 1, 2008

By Gordon Kidd

Inflation and burgeoning costs are two among many factors which have generated a new surge of interest in "fringe benefits" (sometimes referred to as "supplementary remuneration" or "supplementary compensation"). Other specialized forms of compensation ("perks", in the vernacular) such as company cars, windowed offices, etc., which also are the subjects of current study, are outside the scope of this paper. For businesses, interest in fringe benefits is based on concern for employees? welfare, compliance with government requirements, and an increasingly burdensome impact on bottom lines. In 1980, according to Fred D. Lindsey in the October 1980 issue of Nation's Business, employee benefits will cost American employers an estimated $420 billion. To paraphrase Winston Churchill, "some fringes!" Indeed, few if any administrators consider employee benefits as fringes. Employee benefits impact other major areas of a company's operations as well. As listed by Beadle (1980), these areas include employee relations, collective bargaining, short-term costs, long-range funding, manpower planning, compliance with legislation, taxation for the company and for the employee, corporate image in the community, competitiveness for staff, communications, administration, claims cost containment, etc., etc.

Jan 1, 1980

By J. Restrepo, N. Ripepi

"The International Organization of Standards defines risk as “the effect of uncertainties on achieving objectives (15).” In mining, many uncertainties can influence the outcome of personal or professional objectives and are often difficult to predict. Risk management, the minimization and control of adverse effects from exposure to identified risks, is a well-established concept that can summarized as “being smart about taking chances” (12). Risk management now consists of management processes unique to numerous organizations across many industries, as varying sectors encounter a variety of needs, including the analysis and mitigation of risks related to physical security, product liability, information security, various forms of insurance, regulatory compliance, and workplace safety (12). The reoccurrence of multiple fatality events in the US mining industry, especially the underground coal sector, suggests an opportunity for improved methods of major safety hazard identification, assessment, and mitigation. A risk management approach would include ready identification and mitigation of these risks, inclusive stakeholder engagement, and rapid integration. While many solutions to reducing the risk of mine disasters have been proposed including stricter regulation and improved technology, a comprehensive risk management approach has yet to be fully integrated in the US mining industry. In December of 2006, R. Larry Grayson of the National Mining Association’s Mine Safety Technology and Training Commission called for “a new paradigm for ensuring safety in underground coal mines, one that focuses on systematic and comprehensive risk management as the foundation from which all life-safety efforts emanate (7).” A risk management approach has already been implemented with success in Australia’s minerals industry as part of a transition during the mid-1990s from a prescriptive based health and safety attitude to a more proactive, duty-of care [risk-based] philosophy (13, 16, 17).FUNDAMENTAL ELEMENTS OF RISK MANAGEMENT TECHNIQUES The fundamental components of a comprehensive risk assessment/management program are well-established within the realm of mining health and safety. Figure 1 depicts the elements of a typical mining hazard management framework. The first step in any safety-based risk management system is to identify and assess hazards by their location, nature, and magnitude within a mine. Next, a decision is made about choosing to eliminate, mitigate, or tolerate each hazard. Ideally, a hazard will be eliminated during the design stages of mining, though dynamic mining conditions often require continuous improvement and reevaluation of existing hazard controls. If elimination is not possible, hazard mitigation actions can consist of methods, rules, equipment, competencies, or other mechanisms. If a hazard is simply tolerated, as many inherent mining hazards must be, then specialized administrative controls must be utilized to minimize losses. During this process, the performance of each action is monitored and modified as needed (13)."

Jan 1, 2015

By J. Paraszczak

Application of teleoperated and automated (or ?autonomous?) mobile equipment in underground metal mines is a promising avenue for overcoming some of the challenges facing mine operators. These include, but are not limited to, the issues related to safety and health of underground workers, better use of the shift time leading to increased productivity, skilled manpower shortages, and remoteness of some mine sites. Autonomous load-haul-dump machines and trucks offer several benefits over man-operated ones, but their use at their full capacity is a challenging and complex task. This paper makes an overview of commercially available equipment and systems and their applications. It examines factors affecting adversely availability, utilization, and production efficiency of autonomous vehicles and compares them to conventional man-operated machines. Technical and operational aspects are discussed and their criticality is analyzed. Based on that, recommendations concerning means and measures that may help raise operational effectiveness are given. It is stressed that due to a scarcity of publicly available information on the performance and cost of autonomous loading and haulage operations, more field studies and in-depth analysis are needed.

Feb 23, 2014

By N. K. Dumakor-Dupey, G. B. Sakyi-Addo, K. J. Bansah

"Artisanal and small-scale mining (ASM) occurs in many countries around the world, and provides a source of livelihood to many impoverished local people in areas where it occurs. This paper reports the role of female participants and reasons why they engage in ASM. Field visits were made to 12 ASM sites located in the Tarkwa Mining District of Ghana to conduct interviews with male diggers and female participants. It was observed that over 100 women between the ages of 18 and 50 participate in ASM for survival. They engage in ASM largely because they have no alternative employable skills and income sources. These female participants depend on ASM to sustain the lives of their dependents. INTRODUCTION Artisanal and small-scale mining (ASM) conventionally involves use of rudimentary tools (such as picks, shovels, chisels and hammers) to exploit precious minerals and metals from the ground. It has been a major source of livelihood to many impoverished local people for more than a century. In many instances, it is the only source of income to indigenous people who have no alternative employable skills. The World Bank estimated that more than 100 million people around the world benefit from ASM which largely occurs in developing countries in Asia, Africa, Oceania, and South and Central America (World Bank, 2013). Cobalt, which is used in lithium-ion batteries to power cellphones, laptop computers, and electric vehicles, is largely produced by artisanal miners in Congo (The Washington Post, 2016). In Sudan, ASM is a significant contributor to the national economy, accounting for about 85% of total gold extracted yearly from 2010 to 2015 (Ibrahim, 2015). Also, according to the Embassy of Sierra Leone in Washington DC, USA, 90% of mineral export in Sierra Leone can be attributed to thriving artisanal diamond mining in the country (Sierra Leone Embassy, 2016). In Ghana, the ASM sector was recognized by government as a multimillion industrial activity, and through a series of initiatives, it was legalized by promulgating the Small Scale Gold Mining Law of 1989 (PNDCL 218). Presently, artisanal mining is widely practiced in two forms: licensed (registered), sometimes referred to as formal ASM, and unregistered (informal or illegal) operations, popularly called “galamsey”, a name believed to have been derived from “gather and sell” by ancient miners who could not communicate in the English language with European/British miners. The ASM sector in Ghana, like other countries, has seen a rise in female participation over the years. A report by the International Labour Organization (ILO) indicated that women account for about 15% of total workforce in ASM in Ghana, and up to 50% in Africa (ILO, 1999). Other researchers have also estimated women participants in ASM to be between 30 and 70% in Africa (Hinton et al., 2003a; Hinton et al. 2003b; Hilson, 2002). Presently, there is no reliable data from Ghanaian authorities on number of females engaged in ASM. However, data obtained from 15 ASM sites suggest that at least 40% of the employees are women. It is expected that a similar trend exists across ASM operations in Ghana."

Jan 1, 2017

By Yuting Xue, Alper Kirmaci, Taghi Sherizadeh, Dogukan Guner, Khaled Mohamed

Rib brows present a significant safety hazard in underground coal mines in the United States. To address this issue, researchers at the National Institute for Occupational Safety and Health (NIOSH) and Missouri University of Science and Technology (MST) are developing a practical tool to assess both the potential of rib brow formation and the stability of any formed brows. As part of this effort, a monitoring study was conducted to assess the potential for rib brow formation in coal pillar ribs. This study was conducted in a room-and-pillar coal mine where coal pillar ribs are prone to developing rib brows. Although no rib brows formed in the instrumented pillar, data from monitoring and visual observations provided valuable insights into the loading mechanisms impacting the instrumented pillar. These findings helped identify factors that may reduce rib brow formation, including the cavability of the roof in mined areas, the applied rib support, the strength of rock partings, and the overall integrity of the coal seam. The scientific findings published in the case study aid in assessing the potential of brow formation, offering additional evidence for the need to improve rib control methods in underground coal mines.

Feb 1, 2025