Search Documents

By Kenneth N. Han

The effect of anions such as sulfate, chloride, and nitrate on the solubility of rare earth element-bearing phosphates and fluorocarbonates has been examined using relevant thermodynamic data. The study has found that these anions have significant influences on the overall dissolution of rare earth elements (REEs) from various sources in the aqueous media. The thermodynamic calculations in this study have indicated that the speciation of REEs with the anions tends to increase the overall solubility of the REE-bearing minerals. However, in some cases, strong precipitation of REEs with some of these anions causes an adverse effect on the solubility of these elements. It has been found that sulfate ion has the most pronounced effect on the solubility compared to nitrate and chloride, in which the latter two acids exhibited almost identical results. The calculated results have indicated that REE-oxide (hydrated) is the easiest compound to dissolve, followed by carbonate, phosphate, fluoride, sulfate, fluoro-carbonate, and oxalate in that order.

By A. A. Zatout, G. H. Sedahmed, T. M. Zewail, M. H. Abdel-Aziz, B. S. Ibrahim, E-S. Z. El-Ashtoukhy

In this work, the possibility of intensifying the cementation process in stirred vessels was studied by using the perforated baffles as turbulence promoters; the cementation reaction of Cu+2 on Zn was selected as a model. Zn was used in the form of a sheet lining the inner wall of an agitated vessel. Parameters considered are initial concentration of Cu+2, solution temperature, impeller rotation speed, and impeller geometry. Within the present range of parameters studied, the rate of cementation was found to increase with increasing initial concentration of Cu+2, solution temperature, and impeller rotation speed. At the same rotational speed, a flat turbine gave a higher rate of cementation than a 45° pitched turbine. The present suggested that baffles’ geometry gave superior performance in terms of mass transfer of copper cementation compared to the conventional baffle geometry. All parameters that affect the rate of cementation were correlated in the form of dimensionless equations suitable for the design and performance prediction of the agitated vessel. Potential applications of the obtained results in the field of hydrometallurgical processes and wastewater treatment were discussed.

Jan 12, 2021

By K. V. K. Prasad

Stochastic simulation has been routinely used for performing risk and sensitivity analyses in a variety of fields. The commonly used means of generating the simulations has been the Monte Carlo approach which usually employs a Simple Random Sampling (SRS) scheme of the variable distributions. This method is prone to sample clustering and requires a large number of samples to represent the distribution faith-fully. This can become problematic for simulating complex processes where it is impossible to run an arbitrarily large number of replicate simulations. The Latin Hypercube Sampling (LHS) method uses a stratified sampling approach which assures representation of the input distributions for any given number of samples. In this paper the LHS and SRS approaches are compared using a petroleum resource estimation example.

Jan 1, 1993

By Jonathan K. Hrica, Brianna M. Eiter

The ability to identify hazards during a workplace examination is a critical skill for mineworkers to have in order to maintain a safe workplace. While research suggests that being able to successfully recognize hazards requires a complex set of competencies, it is unclear which competencies are most critical to adequately perform a workplace examination. This paper presents a hazard recognition competencies framework as an explanation of the competencies that affect mineworker hazard recognition. To better understand how the industry is selecting and preparing workplace examiners, researchers fromthe National Institute for Occupational Safety and Health (NIOSH) interviewed nine health and safety (H&S) professionals at surface stone, sand, and gravel mine sites throughout the USA. A primary purpose of these interviews was to verify the competencies included in the hazard recognition competencies framework and to understand why these competencies are critical. Finally, the results of this study are presented within the context of current NIOSH research findings related to hazard recognition.

Jul 27, 2020

By C. L. Kosmoski, B. M. Eiter, B. P. Connor

"In the recent past, the mining industry has witnessed a substantial increase in the numbers of fatalities occurring at metal and nonmetal mine sites, but it is unclear why this is occurring. One possible explanation is that workers struggle with identifying worksite hazards and accurately assessing the associated risk. The purpose of this research was to explore this possibility within the mining industry and to more fully understand stone, sand and gravel (SSG) mine workers’ thoughts, understandings and perceptions of worksite hazards and risks. Eight mine workers were interviewed and asked to identify common hazards they come across when doing their jobs and to then discuss their perceptions of the risks associated with those identified hazards. The results of this exploratory study indicate the importance of workers’ jobrelated experience as it applies to hazard identification and risk perception, particularly their knowledge of or familiarity with a task, whether or not they had personal control over that task, and the frequency with which they perform that task. IntroductionAccording to the U.S. Mine Safety and Health Administration (MSHA, 2015a), 37 mine workers were fatally injured in accidents at metal and nonmetal mine sites between October 2013 and January 2015, following a record low of 16 in 2012 and in 2011. In 2014 alone, 29 mine workers were fatally injured at a metal or nonmetal mine site, and 52 percent of these fatalities occurred at a surface stone, sand or gravel (SSG) mine. In January 2015, Joseph A. Main, Assistant Secretary of Labor for Mine Safety and Health wrote to stakeholders in the metal and nonmetal mining community and identified several areas where improvement was necessary to promote the health and safety of mine workers. One area identified was an increased focus on “daily and effective workplace exams to find and fix hazards” (MSHA, 2015b).Hazard detection is challenging in the mining industry, despite the existence of regulation. Mining is a major undertaking involving the use of complex heavy machinery, equipment and processes as well as numerous and diverse worker activities that take place in a dynamic, challenging environment (Scharf et al., 2001). In other industries that are similarly dynamic and unpredictable, such as the construction industry, a large proportion of hazards go undetected (Carter and Smith, 2006). It is critical that miners are able to both recognize worksite hazards and accurately assess the risk associated with the hazards, because their health and safety depend on their deciding whether and how to remove hazards and mitigate risks."

Nov 1, 2016

By S. Maurigiannakis

In an effort to promote sustainability in the construction industry, the natural decorative stones that cover large external areas of buildings may be replaced with artificial stones. In this paper the physical and mechanical properties of artificial decorative stones are presented and are critically compared with corresponding natural stones. To test suitability for various applications, artificial stone specimens were subjected to weathering testing (freezing-thaw cycles in a climatic chamber). Mechanical characterization of these specimens was based on uniaxial compressive testing as well as non-destructive ultrasonic testing. Preliminary results show that artificial stones can replace natural stones, thus creating a sustainable development option for the construction industry.

Jan 1, 2003

By Montaser S. El‑Salmawy, AHMED A. S. SEIFELNASSR, Ahmed Al‑Abady, Abdeaziem M. Abdelaal, Amr F. M. Ibrahim

Iron is a key detrimental impurity in silica sands that determines their contribution to high-technology industries. Herein, a simple ecologically sound approach is investigated for iron removal from a silica sand sample obtained from the El-Zaafarana area-Egypt. The sample was subjected to a detailed microscopic mineralogical study supported by XRD and XRF characterization. The sample was beneficiated using distilled water attrition scrubbing and screening over a 25 μm sieve followed by leaching using a mixture of equal amounts of phosphoric and oxalic acids. Leaching experiments were designed and analyzed using the Box-Behnken design (BBD) methodology. A model was developed and evaluated using the analysis of variance technique to map the relationship between the residual iron oxide in the produced concentrate and selected variables such as leaching temperature, oxalic acid, and phosphoric acid concentrations. XRD and mineralogical analysis reveal that quartz is the most dominant constituent of the studied sand and other minerals such as kaolinite, iron oxide, rutile, and zircon exist in trace amounts. The head sample shows a silica and iron oxide content of 95.69% and 2379 ppm, respectively. Attrition and separation over a 25 μm sieve increase the silica content to 97.05% and decreases the residual iron oxide to 455 ppm. The final product after leaching under optimized conditions shows 99.82% silica and 55 ppm iron oxide.

Aug 30, 2022

By M. Ralchenko, C. Samson, M. Svilans, C. Walsh

"Through-the-Earth (TTE) radio has been proposed as a means of emergency communications in mines. The propagation of a TTE radio signal depends chiefly on the subsurface conductivity distribution. Robust forward models of signal propagation can be computed based on a realistic conductivity estimate. These models can be used, for example, to optimize frequency, estimate signal range, identify zones of anomalously strong or weak signals, or to optimize the position of the above-ground TTE radio unit. A method was developed to determine the conductivity distribution of a mine overburden using TTE radio transmission data. At multiple locations in an underground test mine, we recorded a wideband electromagnetic signal, spanning a frequency range of approximately 500 to 8,500 Hz, transmitted from a vertical magnetic dipole at the surface. Using a finite-difference time-domain forward modeling code, a layered Earth conductivity model that accounts for topography was fitted to the observed data, which minimizes the difference between the calculated and observed attenuations for each transmitter-receiver pair, for each frequency of interest. Introduction and objectiveThrough-the-Earth (TTE) radio has been proposed for emergency underground communications. The most common type of TTE radio is based on the transmission and reception of signals by electromagnetic induction. These signals are in the extremely low to very low frequency range — in practice, between 400 and 9,000 Hz. This technology was historically developed for mine safety, although recently other applications have been suggested, such as communications in civilian infrastructure like high-rise buildings or tunnels, in the military, and even for wireless detonation and activation. In a coal mine, which is a setting of particular importance for TTE radio due to the higher risk of accidents, day-to-day communications can be done through a wired link. High-frequency line-ofsight systems, whose signals cannot penetrate rock, are also used for communications from nonfixed points. Another option is a leaky feeder system, which is a permutation of a line-ofsight system and a wired link, where a partially shielded coaxial cable allows the signal to “leak” (Delogne, 1982). In an incident such as a mine collapse or explosion, a TTE radio system can still provide a communication link, as wired systems can be severed, and line-ofsight systems cannot penetrate through collapsed portions of the mine, or to the surface (Forooshani et al., 2013; Yarkan et al., 2009)."

Jan 7, 2018

By David B. McWhorter

Conventional analyses of seepage through saturated media do not apply when tailings impoundments are located above a partially saturated zone. Three stages of seepage are identified and methods for estimating the seepage rates and duration of each stage, based upon flow in partially saturated and saturated porous media, are demonstrated. The effectiveness of earthen liners is discussed and procedures for estimating the required properties of the porous media are provided.

Jan 1, 1978

By Del Brock, Dan Wooton

The design/build of two adjacent vertical mine shafts in difficult ground conditions at a mining complex in the midwestern United States required innovative construction techniques. Construction of the 267-m-deep Service Shaft required full depth dewatering wells and ground freezing. Blind drilling was utilized to excavate the 257-m-deep Production Shaft and it was finished with a steel/concrete composite liner that was floated into place. An equally unique component of the installation included supplying a high capacity vertical conveyor system, featuring a 273-m-lift. Other components of the project include the mine level development, as well as the design and installation of three hoisting systems, including a 45-ton capacity men/materials hoisting system.

Jan 1, 2003

By Rudrajit Mitra, Erik Hulthén, TOBIAS HARTMANN, ELISABETH CLAUSEN, Aarti Sörensen

There has been an ongoing debate on how to transform engineering education to better prepare students for today`s professional world that is characterized by increasingly complex problems and challenges that engineers are tasked with upon entering the industry. Within the conceive–design–implement–operate (CDIO) framework, entrepreneurship education presents a valuable pedagogical approach to foster the necessary skills of the students through integrated, hands-on, active learning experiences. While numerous publications have addressed possibilities of how experiential, problem-based, project-based and active learning can be integrated into engineering curriculum, there has been hardly any attention on mining engineering with respect to adopting this approach. This paper will address the possibilities of integrating entrepreneurship education into mining engineering programs in particular. This paper will enhance and foster discussion among academics from mining engineering on how to integrate elements of entrepreneurship education on a course, program and departmental level to infuse value creation experiences across the curriculum.

May 25, 2022

By M. E. Ryan, C. L. Hoebbel, E. J. Haas

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Mention of any company or product does not imply endorsement does not constitute endorsement by NIOSH. ABSTRACT It has been suggested that effective disaster prevention and response in mining requires that elements of emergency management be incorporated into everyday operations, planning, and decision-making, much in the same way that the industry approaches routine risk management. Since Congress passed the MINER Act in 2006, the newly mandated structural and technological advancements in mine emergency response preparation have been made and are apparent, but measureable improvement in mineworker emergency preparedness is difficult to ascertain. To begin exploring whether measurable indicators of mine workforce preparedness can or should be addressed within a risk management framework, NIOSH researchers examined the datasets from two separate research efforts—one which measured the organizational safety climate and self-reported safety performance, and the other which measured individuals’ perceptions of their own self-escape competency. INTRODUCTION In response to the mine disasters in 2006, the United States Congress passed the Mine Improvement and New Emergency Response Act (MINER Act), which strengthened existing regulations [30 CFR, Part 48] and introduced new provisions to improve mine emergency response. Since that time, new technological and structural features, such as mandated redundant communication systems, personnel tracking systems, and lifelines in primary and secondary escapeways, have been installed in underground coal mines across the country. Additionally, mine operators are required to develop emergency response plans, provide adequate supplies of breathable air throughout the mine, provide more frequent and realistic expectations training, and are required to immediately notify the Mine Safety and Health Administration (MSHA) in the event of an accident. While the structural and technological advancements in emergency preparedness are readily observable and easily measured, levels of individual mineworker preparedness remain difficult to assess. There is a general consensus that deficiencies in competence in the non-routine tasks required for individual miners to effectively respond to a mine emergency likely remain (e.g., National Research Council [NRC], 2013), and NIOSH research continues address this concern (Haas, et al., 2015; Hoebbel et al., 2018). To maximize an operation’s capacity to effectively prevent disasters and/or respond to emergency events, it has been suggested that individual and emergency management efforts be incorporated into everyday operations, planning, and decision-making in much the same way organizations manage routine risks to health and safety (Haddow et al., 2017). To the authors’ knowledge, the mindful intersection of routine risk management policies and practices and emergency prevention and response readiness have yet to be empirically studied within the mining industry.

Jan 1, 2019

By M. D. Ballain, V. C. Storhok, B. Pesic, J. C. Sever

Northwest Alloys, a wholly owned subsidiary of Alcoa, produces magnesium from dolomite by reduction with ferrosilicon and aluminum. This process produces alkaline by-products in quantities that allow their consideration for use as commercial by-products. Two such products are dicalcium silicate slag, Di-Cal, and magnesium oxide condensate, MgO. The alkaline properties of these materials offer acid neutralizing capability comparable to the traditionally used lime, therefore, warranting a study for their use in applications where the neutralization of acidic waters or process solutions is required, such as treatment of mine waters. In this ongoing study, three mine waters (Bunker HillMine, Berkeley Pit, and Blackbird Mine) were selected for treatment with Di-Cal and MgO. Lime was used as the background control. The solid precipitates were subsequently contacted with pure water at four different pH conditions for stability testing of prepared metal precipitates (expanded TCLP). It was found that neutralization with Di-Cal results in precipitates which are of equivalent to superior stability than those from lime treatment.

Jan 1, 1999

By James K. Wright

This chapter will discuss the use of financial models as an evaluation tool for various phases of decision making from exploration strategy to the analysis of a producing mine. The text of this chapter was not received in time for printing.

Jan 1, 1979

By Sheshang Singh Chandel, Prvan Kumar Katiyar, Navneet Singh Randhawa, Prince Kumar Singh

Mineral process wastes, such as metallurgical slags nowadays, are of significant metals and materials resources in the circular economy. The usability of iron-making slag is well established; however, steel slag still needs to be utilized due to various physicochemical constraints. In this context, we have reviewed the global steel slag generation, processing, characteristics, and potential application with suggestions for futuristic possibilities to address the technical, economic, and environmental aspects of steel slag recycling. The steel slags inherit characteristics from ore chemistry and their processing routes, which may be Blast Furnace-Basic Oxygen Furnace (BF-BOF) or Direct Reduced Iron-Electric Arc Furnace (DRI-EAF) steel-making routes with/without treatment in a Ladle Furnace (LF). The average generation of slags in BOF, EAF, and LF processes accounts for 110 kg, 70 kg, and 40 kg per tonne of steel, respectively. Considering global steel production of 1878 million tonnes in 2020, the associated slag by-products possess a significant resource of major components like FeO, CaO, SiO2, Al2O3, etc. Selecting a recycling technique depends on the slag's end use, logistics, and physicochemical characteristics. BOF and EAF slag are used ~ 48% in road construction applications and ~ 10% for industrial specific metallurgical use. EAF slag is preferred as cementitious material as compared to BOF. Hot-stage modification of BOF slag has emerged as a preferred method to achieve desired chemical and subsequent mechanical properties for end use. BOF slag has high carbon dioxide sequestration potential for in-plant remediation among steel slags.

Nov 20, 2023

By Josef Arnold, Norbert Fuegenschuh

The “Eggequerung” is an important part of the German Railway’s (Deutsche BahnAG) modernized Dortmund—Kassel line. The heart of this 13-km-long (8 miles)construction lot is the double-track Egge Tunnel with a total length of 2,880 m(9,450 ft.). The tunnel was driven using the New Austrian Tunnelling Method (NATM).The construction contract also called for a reinforced concrete secondary lining, guaranteed for a full water pressure of 30 m (100 ft.) water column. Preliminary geological study already showed that very problematic geological-hydrological conditions would have to be expected. This talk describes the chosen NATM driving concept that was adapted to the prevailing geological and hydrological conditions, the special driving method applied in geologically difficult zones as well as the water control concept used during driving. The flexibility and the limits of the NATM under exceptional hydrological conditions are illustrated. Also described are reinforced concrete lining works for the watertight secondary vault (reinforced concrete secondary lining without water-proofing membrane).

Jan 1, 2003

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

The integrated grouting method, as developed in the USSR, can be applied to multi-purpose operations that in¬clude the construction of shafts, drifts, and tunnels. In the USSR it has been used extensively for primary and final grouting of underground excavations in mining engineering and civil engineering projects. It has been applied in projects where the primary objective was waste contain¬ment. It has also been used to control subsidence beneath buildings located over mined out openings and to eliminate the flow of ground water beneath and around dams. This chapter considers several industrial applications in the form of case histories. The word integrated means that grouting activities were integrated with other activities. 9.1 CASE HISTORIES OF GROUTING FRACTURED ROCK WHEN SINKING VERTICAL SHAFTS The integrated grouting method has been applied most widely in the sinking of vertical shafts in fractured, satu¬rated rock. As explained previously herein, grouting oper¬ations preferably are carried out from the ground surface where they are integrated into the schedule of the setting up of the shaft excavation and construction equipment. Such integration reduces significantly the length of time required for preparation of shaft construction and the time required to sink the shaft. The increased efficiency is achieved by the elimination of cementing operations from the working face upon the penetration of each aquifer. Concomitantly, labor and energy consumption during shaft sinking are minimized because the more complicated and labor-intensive work is carried out at the surface section. Table 9.1 presents the essential parameters for the pri¬mary grouting of saturated fractured rock carried out by the integrated method when sinking vertical shafts. 9.1.1 NAGOL'CHANSK MINE NO. 1-2, VENTILATION SHAFT NO. 1 The integrated method of grouting saturated fractured rock through holes drilled from the surface was employed for the first time during the sinking of vertical shaft No. 1 at the Nagol'chansk mine No. 1-2 in the Don Basin. The shaft had an inside diameter of 6 m. The grouting operations commenced by using cement grout with a density of 1.7 to 1.8 g/cm3. Clay-based grout with cement and other addi¬tives was used only for grouting the aquifers where cement grout proved to be ineffective. By the time of the grouting of ventilation shaft No. 1, hydrodynamic analytical methods were well in hand and a preliminary method for designing isolation curtains had been developed. A method for designing and drilling ori¬ented directional drillholes whose natural curvature re¬flected the characteristics of the fracturing had been devel¬oped. The majority of the necessary equipment had been developed. Clay-based grouts were considered ready for the first industrial application. The hydrogeologic environment at the Nagol'chansk mine No. 1-2 contained many prolific aquifers. According to monitored drillhole data, the total expected inflow into ventilation shaft No. 1 without grouting was 425 m3/hr. This large ground water inflow rate was supported by in¬formation obtained during the sinking of the main shaft and from the auxiliary shaft of the "Nagol'chansk" mine No. 1-2. The construction contractor at the site began sinking ventilation shaft No. 1 to a depth of 217 m by cement grouting from the working face of the shaft. As a result of the cement grouting operations, the inflow of water was reduced from 105.4 to 40 m3/hr over this 217 m interval. However the residual inflow rate caused the shaft to become functional at the depth of 217 m. At this point all grouting operations were transferred to SPETSTAMPONAZHGEOLOGIA (STG) in an effort to improve the operation. In order to carry out preliminary grouting from the sur¬face, seven drillholes were installed and designed for re¬ceiving grout. Drilling was implemented by the ZIF-1200A rig to the design depth of the shaft. The geometry of the principal fracture system that would be encountered by the shaft was estimated while breaking ground using informa¬tion from other shafts. The drillholes were arranged so that they cut through the aquifers uniformly around the shaft. Some preference was given to intercepting the aquifers that were located along the rock dip above the shaft bottom because it was established that the ground water in the aqui¬fers flowed downward along the dip into the cone of de¬pression of the shaft. Investigations in the drillholes using the DAU-3M flowmeter described in Chapter 3 showed that all of the nine aquifers were penetrated by the time a depth of 690 m had been reached. The flowmetric information showed that aquifer numbers [1 and 2], [4, 5, and 6], and [7 and 8] had practically identical hydrogeologic characteristics; so it was decided to connect them into combined stopes and inject the grout using five stopes instead of nine. Table 9.2 shows the results of the grout injection into the aquifers. The volume of grout pumped into the separate intervals through single holes varied from 204 to 15 m3. The trend of grout consumption showed a reduction of grout consump

Jan 1, 1993

By Yanxu Shen, Cheng Liu, Zhijie Chen, Hao Chen, Huimin Gao, Zijie Ren

Fluorite, a kind of critical non-metallic minerals, is the primary source of industrial fluorine. Sodium oleate (SO) is commonly used as the collector of fluorite ores. However, because of its some features (such as the low solubility, high solidifying point, and poor dispersion of SO) at low temperatures, it profoundly inhibits its collecting ability as well as the flotation performance. Herein, we have developed a low-temperature-resistant collector for the efficient flotation separation of fluorite from quartz. The advantages and disadvantages of the SO and sodium petroleum sulfonate (SPS) were analyzed by comparing the performance under different temperature conditions. The results of flotation tests suggest that SPS exhibited much better collecting performance than SO under low temperature. The flotation mechanism of the two collecting agents were further analyzed by contact angle measurements, zeta potential measurements, Fourier-transform infrared spectroscopy (FT-IR), and flotation kinetics. The results indicated that both collectors can selectively undergo electrostatic and chemical adsorption with fluorite, with no adsorption on quartz surface. The sulfonic acid group in SPS is a hydrophilic functional group, which has a relatively higher solubility in water. Therefore, the water solubility of SPS is better at low temperatures.

Sep 30, 2021

By Eduardo Pimenta de Melo, Rambabu Pothina, Rajive Ganguli

Sensors are everywhere in the mining industry, with sensor information being used to monitor and operate processes. Therefore, when sensor information is wrong, economic losses can occur. Unfortunately, sensor errors are usually not detected till they become large. This is problematic as most calibrate their sensors no more than once a year (Beamex, n.d.). Using principles of data mining, where all relevant information is tapped to glean hidden information, Pothina [8] designed an algorithm to detect errors in temperature sensors in gold stripping circuit in Pogo mine, Alaska. This paper continued his work by analyzing the behavior of the algorithm on baseline data and testing the algorithm in new data and under more rigorous conditions. It also made a change to the algorithm. The modified algorithm performed very well in the new data. It also worked well under the new error conditions. Three types of errors were seeded, a fixed additive error (+ 2%), a fixed subtractive error (− 2%), and a noisy, normally distributed error, with a mean value of + 2%. Artificially seeded errors were detected within about 20 gold stripping cycles. Inherent bias in operation impacted algorithm performance by increasing the number of cycles needed to detect errors. This paper reinforced Pothina’s [8] conclusion that when data mining approach is used, sensor errors can be detected even when they are pretty low. Significant economic losses can thus be minimized.

By Y. Lahaye, O. Martinsson, B. I. Palsson

"Four main and three minor rare-earth-element (REE)-bearing minerals were identified and quantified in the Kiirunavaara apatite iron ore tailings using optical microscopy, an electron probe microanalyzer (EPMA) and a mineral liberation analyzer, and their chemical compositions were analyzed by the EPMA and laser ablation inductively coupled plasmamass spectrometry. REEs are shown to be contained in the minerals apatite, monazite, allanite, titanite, zircon, thorite and synchysite. In zircon, thorite and synchysite, they occurred in only trace amounts and contributed limited amounts to the total REE budget, and these are consequently of minor importance. Monazite occurred as inclusions in apatite and as free particles, 90 percent liberated. Allanite occurred to some degree in mixed grains with magnetite but also as free particles. Monazite mainly reported to the apatite concentrate, while allanite and titanite largely went to the tailings, the latter preferably to those fractions smaller than 38 µm. The amount of titanite in the finest tailings fraction was 2.3 weight percent, containing close to 1 percent REEs, with heavy rare earth elements (HREEs) making up 28 percent of the total REEs. However, a texturally distinct group of titanite grains showed an HREE/REE ratio of up to 67 percent. Furthermore, titanum dioxide analyses indicate that titanite is preferentially released into the tailings from the secondary magnetic separation step in the concentrator. Our data therefore suggest that titanite, occasionally enriched in HREEs, can be extracted from the processing stream and might thus be considered a new source for REEs at Kiirunavaara and similar deposits.IntroductionDeposits of apatite iron ores are the major source for iron in the European Union and are exploited by Luossavaara-Kiirunavaara AB (LKAB) in several mines in the Kiruna-Malmberget area in northern Sweden. Kiirunavaara is the largest of the apatite iron orebodies in Sweden, comprising more than 2 Gt of iron ore with 60 to 68 percent iron (Fe). At the end of 2015, the total accumulated production of crude ore from openpit and underground mining since the start of mining was 1,566 Mt, with ore reserves of 644 Mt grading 46.3 percent Fe (LKAB, 2016). The deposit defines a steeply dipping tabular body, approximately 6 km long and up to 180 m thick, extending at least 1,500 m below the surface. It is situated in the middle part of the Palaeoproterozoic Kiirunavaara Group of volcanic rocks and follows the contact between a thick pile of trachyandesitic lava and overlying pyroclastics (Martinsson, 2004)."

Jan 1, 2017