Search Documents

By Hao Zhang, Mi Zhou, Lichun Jiang, Xihong Zhang

This study investigates the roof stability of underground limestone mining in the presence of stratified joints during the excavation process. An analytical solution is derived to predict the stresses and deformation of underground tunnel structures, with the structure simplified as a double-hinge arch. The accuracy of the analytical model is validated through comparison with finite element modeling results. A parametric study is then conducted to assess the influence of different design parameters on the optimization of tunnel stability during excavation. The results indicate that the best stability of the tunnel can be achieved in engineering practices when the applied load (q) is 5 MPa and the joint inclination angle (θ) is 45°, with the roof span and thickness set at either 12 m and 8 m or 15 m and 10 m. These findings provide valuable design guidance for underground limestone mines with stratified joints.

Oct 18, 2023

By A. Thatcher, C. Day, C. Meyer

The purpose of this paper is to provide general information about the bioaccessibility of metals and specific information about the use of bioaccessibility in risk assessments (human health risk assessments [HHRA] or ecological risk assessments [ERA]) and a list of sites where regulatory agencies have approved the use of bioaccessibility data in risk assessment. The memorandum also cites current U.S. Environmental Protection Agency (USEPA) guidance as well as state specific guidance where applicable. BRIEF HISTORY OF METAL BIOACCESSIBILITY TESTING AND METHODS The bioaccessible fraction of a constituent is that fraction that dissolves or desorbs from its matrix (e.g., soil) in the gastrointestinal tract and is available for absorption (USEPA 2007a; ITRC 2011; ITRC 2017). This is different from the bioavailable fraction, which is the percentage of the amount of an element that an organism is exposed to that is absorbed by that organism during a given time under defined conditions (USEPA 2007a). The bioaccessibility factor is the percentage of a metal that is potentially available for absorption and, therefore, is a conservative estimate of the bioavailable fraction since all that is available for absorption may not ultimately be absorbed into the organism’s system. Currently, there are two main techniques for estimating bioavailability of metals within a medium: in vivo animal studies (time-consuming and often cost-prohibitive), and in vitro tests that simulate human, or animal digestion in a laboratory setting. In vitro and in vivo test methods and protocols have been extensively evaluated by numerous researchers (Ruby et al. 1996; Rodriguez and Basta 1999; Sips et al. 1998; Sips et al. 2001; Molly et al 1993; Oomen et al 2002; Kelley et al. 2002; Oomen et al. 2003; Furman et al. 2006; Drexler and Brattin 2007; Basta et al. 2007; Wragg et al. 2009; Wragg et al. 2011; Chaney et al. 2011; Bradham et al. 2015; Bradham et al. 2018). The most recent scientific literature demonstrates that protocols used to estimate the bioavailability of metals to mammals also predict bioavailability of metals to birds as well (Beyer et al., 2016).

Jan 1, 2019

By Samir Kumar Pal, Rajasekar Rathanasamy, Gobinath Velu Kaliyannan, Moganapriya Chinnasamy, Sathish Kumar Palaniappan

The research examines the performance of uncoated and coated tungsten carbide-cobalt rock cutting bits. It aims to optimize process variables (cutting speed, depth, coating material) considering multiple output responses (cutting forces, specific energy, wear rate, material removed, angle of reaction forces). The study uses a hybrid optimization technique combining Taguchi design, grey relational analysis, and fuzzy logic. The optimal parameter combination was found to be cutting speed: 200 mm/s, cutting depth: 6 mm, and titanium aluminum silicon nitride coating.

Apr 24, 2022

By K. Fuenkajorn, S. Serata

Discussion by S. Serata and K. Fuenkajorn Background Results of the above study in the August 1991 issue of Mining Engineering offer valuable lessons in the solution of cutter-roof problems. The original study plan was initiated by the discussion authors to solve the problems using the "stress control method" of mining (Serata 1976, 1982; Serata, Carr and Martin, 1984; Serata and Gardner, 1986; Serata, Gardner and Preston, 1986; Serata, Gardnerand Shrinivasan, 1986; Serata and Kikuchi, 1986; Serata, Preston and Galagoda, 1987) However, the plan and the planner were changed to the arrangement reported in the paper. The change was considered reasonable at the time due to the mine engineers' uncertainties about the stress control method. Consequently, the basic principle of the study was shifted from the original stress control method to the method described in the paper, which will be called the "yield pillar method" for the purposes of this discussion. The paper convinces the reader that the yield pillar method fails to solve the cutter-roof problems. This doesn't mean that the stress control method also fails. Actually the contrary is true, as discussed below. Limitation of the yield pillar method The paper illustrates clearly how poorly the yield pillar method performs in solving the problem. The reason for this failure is the lack of the protective stress envelope needed to stabilize the cutter roof. Unfortunately, the protective envelope cannot be formed properly without utilizing the stress control method of mining. Changing the pillar size does not make much difference in the roof stability. Stress measurement The key issue is how to form the global stress envelope to make the gate entries safe for production. Therefore, measuring the stress condition of the ground around the mine opening is critically important to solving the cutter-roof problem, regardless of the method applied. With regard to the stress measurement, there is a serious question as to the reported stress state of [6 i = -51.7 MPa (-7499 psi), G2 = -44.5 MPa (-6458 psi) and 63 = -30.8 MPa (-4465 psi)]. It is mechanically impossible to have such a stress state at any location in the mine ground since the known initial vertical stress [o,,] is less than or equal to 800 psi. There may be a large stress state in the [61] direction, but that is possible only at the expense of the [63] value. Having the above stress tensors in the mine is simply impossible. The questionable, reported stress values could be attributed to the application of the overcoring method, which tends to produce erroneously large stress values in the extremely nonelastic mine ground. Stress control method The paper should be considered as a major contribution demonstrating the limitation of the yield pillar method. At the same time, the paper does not disprove the stress control method. However, in comparing the paper with stress control studies conducted in other similar failing grounds, the stress control method appears to be able to solve the problem more effectively. Therefore it is advisable that the mine not give up its efforts to solve the problem. [•] References Serata, S., 1976, "Stress control technique - An alternative to roof bolting?," Mining Engineering, May. Serata, S., 1982, "Stress control methods: Quantitative approach to stabilizing mine openings in weak ground," Proceedings, 1st International Conference on Stability in Underground Mining, Vancouver, BC, Aug. 16-18. Serata, S., Carr, F., and Martin, E., 1984, "Stress control method applied to stabilization of underground coal mine openings," Proceedings, 25th US Symposium on Rock Mechanics, Northwestern University, June, pp. 583-590. Serata, S., and Gardner, B.H., 1986, "Benefits of the stress control method," invited paper, American Mining Congress Coal Convention, Pittsburgh, PA, May 7. Serata, S., Gardner, B.H., and Shrinivasan, K., 1986, "Integrated instrumentation method of stress state, material property and deformation measurement for stress control method of mining," invited paper, 5th Conference on Ground Control in Mining, West Virginia University, Morgantown, WV, June 11-13. Serata, S., and Kikuchi, S., 1986, "A diametral deformation method for in situ stress and rock property measurement," International Journal of Mining and Geological Engineering, Vol. 4, pp. 15-38. Serata, S., Preston, M., and Galagoda, H.M., 1987, "Integration of finite element analysis and field instrumentation for application of the stress control method in underground coal mining," Proceedings, 28th US Symposium on Rock Mechanics, Tucson, AZ, pp. 265-272.

Jan 1, 1993

By J. H. van Laar, C. S. L. Schutte, M. Le Roux

Highly energy-intensive systems prone to wastage are significant causes of unnecessary energy losses in industry. Deep-level mine chilled water reticulation systems fall within this category of inefficient energy-intensive systems. Some techniques (measured baselining, zero-waste baselining, leak detection, and control valves) exist to identify and reduce wastage in mine water reticulation systems. However, these techniques have not been compared, which begs the question of which is more accurate. A need, therefore, exists to compare these methods to determine the effectiveness of each. This study investigates each method and applies them to a case study mine, providing a platform for comparison. These methods identified wastage ranging between 2 and 20 l/s (3–30% of water consumption). The comparative effectiveness of the methods from best to worst was found to be zero-waste baselining, leak detection, control valves, then measure baselining. This study proposes an application procedure combining the considered methods to identify and eliminate wastage on deep-level mine systems more efficiently.

Jan 31, 2024

By Wen Tao Liu, Tong Tian, Fu Sheng Niu, Xiu Man Liang

In order to address the difficulty of accurate segmentation of froth images of different sizes, a method of froth image segmentation based on highlight correction and parameter adaptation is proposed. First, a machine vision system on a single-cell flotation machine is built to collect froth images. Homomorphic filtering is used to improve the uneven brightness and shadow of the images. Fuzzy c-means (FCM) clustering is then utilized to classify similar highlights that belong to the same froth. After Otsu threshold segmentation, a parameter-adaptive morphological operation is used to extract the marker points and edge bands and correct the froth edges in the original image. Finally, the modified image is filtered by morphological reconstruction, and the highlight mark is used as the local minimum point for watershed segmentation. Three sizes of froth images are segmented in comparative experiments. The results show that the proposed method is suitable for the segmentation of froth images of different sizes. The position of the extracted segmentation line is close to reality, with average over-segmentation and under-segmentation rates for froth images of 2.6% and 6.8%, respectively. The froth image segmentation performance is stronger than that of the other methods examined.

The removal of tritium from tritiated water (-0.5 µCiIL) was studied by metallothermic reduction using aluminum. The influence of the three variables namely the aluminum powder amount, the NaOH concentration and the reaction time has been studied on the tritium activity reduction. The experimental results and statistical analysis showed that more than 85% of tritium can be removed from the tritiated water. Further work on the tritium recovery as well as efforts to totally decontaminate water by incorporating a cryogenic concept is currently pursued.

Jan 1, 1998

By D. A. Peacock

"INTRODUCTION Outer space technology and exploration have reached a tipping point so that mining and mineral processing in outer space is now a certainty and not a dream. Several competing companies, worldwide, are well on the way to building spaceships to land on the Moon and eventually mine the Moon and asteroids for volatiles, rare earth metals and Helium-3. The Google Lunar XPrize offers a $30 million prize1. China has recently landed a spacecraft on the Moon. The European Space Agency, with cooperation from the United States, has landed a spacecraft, Philae, on a comet. And, Mars One is planning a one-way trip to establish a settlement of humans on Mars. How and why are the Moon and asteroids and their resources of interest to private space industry and companies? Why are the Moon and asteroids viewed as a potential business venue? GEOLOGY OF THE MOON AND ASTEROIDS –WHY DO WE WANT TO MINE THERE? Space enterprises are actively working towards establishing and operating lunar and asteroid mining locations for resource extraction, resource processing, conversion to salable products, and distribution of the products and services in space and to Earth and beyond2. Forty-five years ago, the Apollo manned missions to the Moon returned rocks and regolith to Earth, which were studied and analyzed. What they found was that the Moon contains valuable minerals and resources. These minerals are largely due to meteor and asteroid impacts, which have, over eons, created this mineral rich regolith. These impacts have occurred on Earth as well, for billions of years, particularly early on in the history of the solar system. However, on Earth, wind, water, and vegetation have erased most of these impacts. On the Moon, in contrast, the only weathering is caused by subsequent impacts and the solar wind. The Moon regolith contains valuable rare earth minerals, platinum-group minerals (particularly where the Moon has been impacted by asteroids), volatiles (useful for processing and habitation), Helium-3 and titanium. Almost non-existent on earth, Helium-3 is abundant and accessible on the Moon and can be used in nuclear fusion power plants, producing much more energy than fission reactions and with much less radioactive waste. One of the main reasons Helium-3 is sought after as a fusion fuel is because there are no neutrons generated as a reaction product. Governments and private companies focus on mining of Helium-3 on the Moon as a basis for their economic models. Moon Express, one of the private companies who is planning on mining on the Moon, will recover moon rocks to fund its early operations25. Subsequently, it will recover Helium-3, platinum, and rare earth metals, as it engages in surface mining operations."

Jan 1, 2016

By Jiawang Hao, Qinglong Zhang, Liang Han, Chuhan Wang, Shenfang Chen, Lan Qiao

The surface collapse and surrounding rock failure caused by goaf instability are the mining disasters that cannot be ignored. It is of great value to evaluate the stability of goaf accurately and treat it economically for the mine safety and the maintenance of ecological environment. However, in previous studies based on numerical simulation methods, the spatial complexity and the irregularity of actual goaf were not considered. Therefore, based on the internal space data of goaf obtained by high-precision laser detector, the goaf stability was comprehensively analyzed through Plaxis software and two-stage fuzzy judgment theory in this study. To effectively improve the goaf stability, the optimal backfill parameters for the goaf treatment were obtained by a series of mechanical tests. The research results provide some good references for the stability evaluation and the treatment of underground goaf.

Sep 26, 2023

By MOHAMMED AMINE BELMI, ANAS DRIOUCH, ABDELAZIZ LAHMILI, LATIFA OUADIF

For many years, underground workings in the Bou Azzer mine have been challenged by geotechnical problems related to the serpentinite instability. The stage of evaluation of the compression potential is crucial to develop an appropriate drilling method and the choice of non-standard support. This research work presents a retro-analysis of serpentinite behavior in underground excavations at different depths, using a multi-approach method, based on several empirical and semi-empirical and theoretical-analytical methods, calibrated by the observational method. The analysis performed in this work reveals that underground excavations in Bouazzer East and Ait Hmane area would encounter compression problems that were recognized as the most serious from a depth of 300 m because of the effects of lithology and tectonics. Therefore, the Aghbar region has a slightly negligible compression potential. The compressive failure mechanism in this mine, depending on the mechanical strength, is started at induced stress of 9 MPa.

Nov 27, 2021

By Arif Emre Dursun

The aim of this study is to present hazard classifications of location, type, and causes of accidents in Turkish coal-extracting industries using Analytic Hierarchy Process (AHP). In this study, fatal mine accidents were analyzed by pairwise comparison and weighting, and the most important hazards were identified by determining the effective main and sub-criteria among location, type, and causes of accidents. For this purpose, 1st, 2nd, and 3rd level hazards consisting of location, type, and causes of accident were determined by using the data of fatal mine accidents in underground and open-pit coal mining in Turkey between the years of 2010 and 2020. And then the data were categorized, and each category was prioritized using the AHP technique. According to the weights calculated by AHP, the most dangerous main criteria at 1st level hazards in underground coal mining is ventilation operations (0.363), while the most dangerous sub-criterion at 2nd level hazards is firedamp explosions and other gas accidents (0.409). On the other hand, in open-pit coal mining, the most dangerous main criteria at 1st level hazards are slopes and benches (0.575), while the most dangerous sub-criterion at 2nd level hazards are landslides (0.429).

Dec 30, 2023

By Rong Lu, Hao Wu, Bing Dai, Guoyan Zhao, Li Cheng, Weizhang Liang

Affected by the disturbance of blasting activities, deformation instability and rock dynamic disasters are prone to occur in deep hard rock roadways. Thus, it is particularly necessary to understand the failure behavior of rocks and roadways under dynamic loads. In this study, a series of impact loading tests were carried out on sandstone samples with and without a circular cavity by a modified split Hopkinson pressure bar (SHPB) test system. The mechanical properties and energy evolution of the samples were systematically investigated, and the effect of cavity size was analyzed. The results showed that the presence of the cavity in the samples weakens the dynamic compressive strength by more than 10%, and the peak strain and brittleness are also reduced to varying degrees. Under dynamic loading, spalling cracks occur first on the roof and floor of the cavity, and then different numbers of shear cracks are formed on the sample diagonals. The eventual shear failure mode is the result of the connection of the shear cracks and the cavity. As the cavity radius increases, the dissipated energy density and fractal dimension both grow accordingly, leading to smaller and smaller rock fragments. The dynamic failure behavior of the circular cavity can be well explained based on the dynamic stress distribution law. Overall, this study can provide a reference for the study of the mechanism of rock burst in deep roadways.

Feb 18, 2021

By BHAMIDIPATI S. SASTRY, ANMAYA NAIK, ASIF AHMAD, Srivatsan Jayaraman Sridharan, ADITYA PANDEY

Wet kata cooling power (WKCP) as measured by a kata thermometer is a well-known heat stress index used in the mining industry. Although, over the years, several researchers proposed different heat indices and indicated limitations of the kata thermometer, WKCP is used in the South African gold mining industry due to its simplicity and rapidity of assessment. This paper presents a comparative analysis of the newly developed empirical expression for the WKCP and some of the more commonly used empirical models. For this purpose, WKCP measurements are obtained based on experiments conducted in a low-speed wind tunnel. Based on a regression technique, the analysis presented aims to assess the disagreement between the empirical model predictions and actual measurements. The correlation is also presented between WKCP and the well-established thermoregulation models using parameters from the low-speed wind tunnel experiments, including dry-bulb temperature (Td), wet-bulb temperature (Tw), barometric pressure (P), and wind speed (v). It is found that the proposed empirical model for the WKCP represents the bioclimatic interaction quite well under the specific parameters that defines the harsh thermal environment and air condition, such as metabolic activity, clothing of the person, and the velocity of the ventilating air in which the person is working. The statistical analyses performed show that the empirical model proposed for the WKCP produces satisfactory estimates of the thermal stress experienced under lower air velocities, light clothing, and higher metabolic activity rates.

Sep 2, 2021

By R. R. Fernández

Newmont Mining Corporation has been processing refractory gold ores by roasting since January 1995. The ores are refractory due to the association of the gold with iron sulfides, namely pyrite and marcasite, and the presence of carbonaceous components and is oxidized in an oxygen-enriched gaseous atmosphere. The structural characteristics of the calcine have a strong influence on the eventual recovery of gold by cyanidation. These characteristics are strongly dependent upon the roasting conditions, mainly the roasting temperature. Originally, the sulfides and carbonaceous matter were oxidized at a temperature that typically ranged between 535 and 560 °C. Controlling the roasting temperature within the lower and narrower range of 510 to 515 °C produced a calcine with a larger surface area(e.g. higher porosity), which resulted in a gold recovery increase of3.3 percent in 2001 equivalent to 5.1 million dollars of additional gross revenue. The new strategies of operating at temperatures never tested before are discussed. It constituted a great challenge to the control room operators for the lower operating temperature falls much closer to the ignition temperature of the sulfide ore and smaller and more frequent adjustments in operating parameters were needed to improve and maintain high gold recoveries. Based on the encouraging results that were achieved in 2001, a decision was made to install a “smart” process control system because the roaster temperature control was performed by manual inputs from the control room operators. The development and implementation of the control system to reduce or eliminate the temperature variability between the different control room operators commenced in June of 2002 and was fully operational by the end of October. Lower roaster temperatures were achieved (500 to 505 °C), which resulted in further increase of gold recovery by about two percent. The overall recovery increase equated to 8.0 million dollars of additional revenue for the first 10 months of 2002.

Jan 1, 2003

By Smart Chika Obiora, Anthony Chukwu

Mining and processing of raw materials is one of the earliest activities of man for survival and development. The products are used for making jewelleries, metal tools, and for exchange of goods and services. However, despite the benefits of mine recoveries, it’s negative and long term effects on the environment and lives remain the point of discussion throughout the world. This study summarizes findings of researches in active/abandoned lead–zinc mines in Enyigba and Ishiagu mining districts including social surveys in the localities surrounding the mines in order to ascertain the effects on the inhabitants. Lead–zinc mining in Enyigba and Ishiagu, southeastern Nigeria has lasted for decades and has affected the socio-economic well-being of the host communities. There are evidences of soil, water, and plants contamination by Pb, Zn, Cd, and Mn in these mining communities. The mining activities also affect the overall social development of the host communities. These effects include retardation in educational development, health care provision, unemployment, and access to potable water supply. Others are rise in poverty level, social amenities, sanitary/hygiene level, high cost of living, and fertility rate. Possible mitigation strategies such as to liaising with relevant government agencies in collaboration with mine owner, mine workers, and host communities can ameliorate these negative effects and promote environmental sustainability.

Feb 24, 2023

By 1980, the U.S. mining community had reached a broad consensus regarding coal pillar design. The pillar load could be estimated from tributary area theory, and the pillar strength from empirical formulas and laboratory coal strength testing. Then the growth of longwall mining required new thinking. Recently, powerful design methods have emerged from analysis of large data bases of real-world pillar successes and failures. These include the Analysis of Retreat Mining Pillar Stability (ARMPS), the Analysis of Longwall Pillar Stability (ALPS), the Mark-Bieniawski rectangular pillar strength formula, and guidelines for preventing massive pillar collapses. Sophisticated numerical models have also helped transform the pillar design landscape. In the process, our understanding of pillar mechanics has been greatly enriched. A new paradigm divides pillar failure into three categories:

Jan 1, 1999

By Felicia F. Peng

One of the serious environmental problems related with the extraction of coal for carbon and energy resources is that upon preparation of coal a large quantity of fine coal has been discarded and/or lost to tailing impoundments. These problems present hazardous conditions to the local community. Also, the precious heating value of energy resources has been wasted and Left unrecovered in the tailing impoundments. Both RCR and SMRC ACTs recognize and mandate an investigation into slurry impoundment problems, including consideration of potential use of those coal fines in the tailing ponds. Bituminous coal producing district 46 encompasses the northern panhandle of West Virginia. The major producing seam in this district is the Pittsburgh coal, 1-7 meters thick. 75 percent of the coal producted in this district is deep mine. This district produces approximately 3 million tons of coal waste materials annually. One of the coal preparation plants in the district which we have visited has been processing Pittsburgh too. 8 seam coal for the past ten years. The characteristic data of the Pittsburgh raw coal is shown in Table 1. The raw coal produced in this district is characterized by its high heating value, high ash and high sulfur contents. The coal preparation plant flowsheet designed and used to process this Pittsburgh raw coal prior to 1979 is shown in Figure 1. It was a partial coal cleaning plant' with 1 092 mt/hr designed capacity, which consisted mainly of a coarse coal cleaning circuit. The rejected fine particles in the size range of -600µm which consisted of vorsiv underflow and cyclone underflow from clean coal streams and spiral classifier overflow from refuse stream were settled down in a thickener with the aid of anionic flocculant prior to being pumped to the tailing ponds for disposal. Figure 2 shows that the same coal preparation plant in Figure 1 was modified to a semi-complete coal cleaning plant and expanded its designed capacity to 1 820 mt/hr, when market of coal fines becomes feasible in 1979. Tabling in the clean coal circuit and thermal dryer in the dewatering circuit were added to the flow sheet. The purpose is to recover more coal fines, reduce more pyritic sulfur and ash contents in coal and also to reduce solid waste material to be stored into the slurry impoundment, giving them a Longer Life. The rejected fine particles fed to the thickener are clean coal fines from two cyclone overflows and the fine refuse from the rufuse cyclone overflow. The clean coal fines presently lost to the tailing impoundments are in the size range of -150 µm and constitute about 5 percent of the overall plant feed. Total amount of tailing waste material accumulated in a tailing impoundment is estimated at 1.3 million metricton for the past ten years.

Jan 1, 1982

By G. J. Joy, J. P. Rider

Technical advances in longwall mining over the last several years have resulted in much larger and faster shearers that have the capability of mining at speeds over 30 m/min (100 fpm). This has resulted in a substantial increase in the amount of dust that is generated at the shearer and during shield advances. Meanwhile, increased underground coal production has put a greater demand on longwall dust control systems as some operators have had difficulty maintaining consistent compliance with federal dust standards. To address this need, the U.S. National Institute for Occupational Safety and Health (NIOSH) is investigating the effectiveness of a water spray manifold mounted on the tailgate end of the shearer body. The sprays are oriented parallel to the tailgate ranging arm, and these sprays create a water curtain confining the dust plume near the face, preventing the dust from drifting into the walkway. This redirection of dust provides a clean air envelope for the tailgate shearer operator and jacksetters working near the tailgate drum. Three different tailgate spray manifold designs were tested and evaluated at the Office of Mine Safety and Health Research (OMSHR) Pittsburgh Longwall Test Facility. Manifolds were equipped with hollow cone or flat fan water spray nozzles and evaluated at three face air velocities — 152, 213 and 274 m/min (500, 700 and 900 fpm)— and at water pressures of 689, 1,034 and 1,379 kPa (100, 150 and 200 psi). Reductions in dust concentrations were observed at six face sampling locations for all the tailgate manifold systems at each of the tested spray pressures and face velocities. Average reduction efficiencies of at least 90 percent were seen at the three sampling locations closest to the shearer for all three manifold systems at nozzle spray pressures greater than 689 kPa (100 psi). Based on results from the laboratory tests showing reductions in dust concentrations at sampling locations downwind of the shearer, a spray manifold was fabricated and evaluated at an underground operation.

Jan 1, 2016

By Charles B. Manula

This paper describes the development of a mathematical model for simulating the behavior of a longwall coal production system. The longwall simulator is a design simulator incorporating both deterministic and stochastic methods to calculate: (a) the size and density of support; (b) the cutting force, power requirements and haulage speed for the loader-shearer; (c) the conveyor size, speed and power requirements; and (d) delay generation at head and tail-gates and the longwall face.

Jan 1, 1978

By F. S. Knoll

GENERAL INTRODUCTION Electrostatic separation has found a number of applications since its initial installation as a processing method. Three broad types of electrostatic installations are discussed in order to provide a practical guide for three widely divergent uses of electrostatic separation. Only operating and installation data are covered in detail. A detailed technical treatment on the various types of electrostatic separation described in this paper can be found in the literature by F. S. Knoll, J. B. Taylor and J. E. Lawer.8, 9 ELECTROSTATIC SEPARATION OF IRON ORE: WABDSH MINES, CANADA Introduction Electrostatic roll-type separator technology which had been in use in various forms since the 1920's evolved in the late 1940's when this separation process was developed and applied to the extraction of titanium bearing minerals from beach sands by J. H. Carpenter. Equipment design and industrial flowsheets developed for the recovery of rutile and ilmenite found new application in iron ore by chance in the year, 1956. From the time of the first beach sands plant, Carpco had developed other technology, gravity and magnetic separation to better serve the beach sands industry. It was in the fall of 1956 that an iron ore producer from the upper Michigan Peninsula sent a sample of jaspilite (fine-grained specular hematite in a jasper matrix) to Carpco's laboratory for the purpose of determining if a new high-intensity magnetic separator would be beneficial. Process Development W. P. Dyrenforth, while presenting a paper on the subject in the fall of 1957, recounts the laboratory tests. "High-intensity magnetic separators have been employed (for the beneficiation of iron ore) with some success and are still being investigated. Magnetic separation is a natural field of investigation, since iron and magnetism have been almost synonymous since ancient times. As a matter of fact, when Carpco first began investigating the possibilities of upgrading specular hematite, the first thought was in terms of magnetic separation; and the second thought was in terms of gravimetric separation. It was found

Jan 1, 1986